[PATCH 1/2] arm: mvebu: turris_omnia: Show MCU type in show_board_info()

[Stefan Roese]

On 29.07.22 13:29, Pali Rohár wrote:
> Different Turris Omnia HW board revisions contains different MCU.
> Show type in show_board_info() to easily identify which MCU is populated.
> 
> Signed-off-by: Pali Rohár <pali at kernel.org>

Reviewed-by: Stefan Roese <sr at denx.de>

Thanks,
Stefan

> ---
>   board/CZ.NIC/turris_omnia/turris_omnia.c | 45 ++++++++++++++++++++++++
>   1 file changed, 45 insertions(+)
> 
> diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c
> index b169abca0956..6fc2018c1cfb 100644
> --- a/board/CZ.NIC/turris_omnia/turris_omnia.c
> +++ b/board/CZ.NIC/turris_omnia/turris_omnia.c
> @@ -62,13 +62,27 @@ enum mcu_commands {
>   	CMD_GET_STATUS_WORD	= 0x01,
>   	CMD_GET_RESET		= 0x09,
>   	CMD_WATCHDOG_STATE	= 0x0b,
> +
> +	/* available if STS_FEATURES_SUPPORTED bit set in status word */
> +	CMD_GET_FEATURES	= 0x10,
>   };
>   
>   enum status_word_bits {
> +	STS_MCU_TYPE_MASK	= GENMASK(1, 0),
> +	STS_MCU_TYPE_STM32	= 0,
> +	STS_MCU_TYPE_GD32	= 1,
> +	STS_MCU_TYPE_MKL	= 2,
> +	STS_MCU_TYPE_UNKN	= 3,
> +	STS_FEATURES_SUPPORTED	= BIT(2),
>   	CARD_DET_STSBIT		= 0x0010,
>   	MSATA_IND_STSBIT	= 0x0020,
>   };
>   
> +/* CMD_GET_FEATURES */
> +enum features_e {
> +	FEAT_PERIPH_MCU		= BIT(0),
> +};
> +
>   /*
>    * Those values and defines are taken from the Marvell U-Boot version
>    * "u-boot-2013.01-2014_T3.0"
> @@ -371,6 +385,36 @@ static int omnia_get_ram_size_gb(void)
>   	return ram_size;
>   }
>   
> +static const char * const omnia_get_mcu_type(void)
> +{
> +	static const char * const mcu_types[] = {
> +		[STS_MCU_TYPE_STM32] = "STM32",
> +		[STS_MCU_TYPE_GD32]  = "GD32",
> +		[STS_MCU_TYPE_MKL]   = "MKL",
> +		[STS_MCU_TYPE_UNKN]  = "unknown",
> +	};
> +	static const char * const mcu_types_with_perip_resets[] = {
> +		[STS_MCU_TYPE_STM32] = "STM32 (with peripheral resets)",
> +		[STS_MCU_TYPE_GD32]  = "GD32 (with peripheral resets)",
> +		[STS_MCU_TYPE_MKL]   = "MKL (with peripheral resets)",
> +		[STS_MCU_TYPE_UNKN]  = "unknown (with peripheral resets)",
> +	};
> +	u16 stsword, features;
> +	int ret;
> +
> +	ret = omnia_mcu_read(CMD_GET_STATUS_WORD, &stsword, sizeof(stsword));
> +	if (ret)
> +		return "unknown";
> +
> +	if (stsword & STS_FEATURES_SUPPORTED) {
> +		ret = omnia_mcu_read(CMD_GET_FEATURES, &features, sizeof(features));
> +		if (ret == 0 && (features & FEAT_PERIPH_MCU))
> +			return mcu_types_with_perip_resets[stsword & STS_MCU_TYPE_MASK];
> +	}
> +
> +	return mcu_types[stsword & STS_MCU_TYPE_MASK];
> +}
> +
>   /*
>    * Define the DDR layout / topology here in the board file. This will
>    * be used by the DDR3 init code in the SPL U-Boot version to configure
> @@ -688,6 +732,7 @@ int show_board_info(void)
>   
>   	err = turris_atsha_otp_get_serial_number(&version_num, &serial_num);
>   	printf("Model: Turris Omnia\n");
> +	printf("  MCU type: %s\n", omnia_get_mcu_type());
>   	printf("  RAM size: %i MiB\n", omnia_get_ram_size_gb() * 1024);
>   	if (err)
>   		printf("  Serial Number: unknown\n");

Viele Grüße,
Stefan Roese

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de