[PATCH v2 0/9] Add DM support for atmel NAND driver

[Simon Glass]

Hi,

On Mon, 29 Aug 2022 at 00:41, Michael Nazzareno Trimarchi
<michael at amarulasolutions.com> wrote:
>
> Hi
>
> On Mon, Aug 29, 2022 at 8:19 AM Balamanikandan Gunasundar
> <balamanikandan.gunasundar at microchip.com> wrote:
> >
> > Change include:
> >
> > - Adapt GPIO descriptor apis for U-Boot. Use
> >   gpio_request_by_name_nodev, dm_gpio_get_value etc.
> > - Use U_BOOT_DRIVER instead of platform_driver.
> > - Replace struct platform_device with struct udevice
> > - Check the status of nfc exec operation by polling the status
> >   register instead of interrupt based handling
> > - DMA operations not supported. Remove it
> > - Adapt DT parsing to U-Boot APIs
> >
> > v2:
> >
> > - Add linux reference version in the commit message from which the
> >   driver is ported from
> > - Reword the commit message to describe the changes clearly
> >
>
> Thank you to repost it again, I will review it and try to include soon
>
> Michael
>
> > Balamanikandan Gunasundar (9):
> >   nand: atmel: Add DM based NAND driver
> >   nand: atmel: Add pmecc driver
> >   mfd: syscon: Add atmel-matrix registers definition
> >   memory: atmel-ebi: add Atmel EBI (External Bus Interface) driver
> >   mfd: syscon: atmel-smc: Add driver for atmel SMC
> >   configs: at91: sam9x60ek: Enable DM based nand driver
> >   ARM: dts: at91: sam9x60: Add nodes for EBI and NAND
> >   ARM: dts: at91: sam9x60ek: Enable NAND support
> >   board: sam9x60ek: remove nand init from board file
> >
> >  MAINTAINERS                                  |    1 +
> >  arch/arm/dts/sam9x60.dtsi                    |   42 +
> >  arch/arm/dts/sam9x60ek.dts                   |  103 +
> >  board/atmel/sam9x60ek/sam9x60ek.c            |   59 -
> >  configs/sam9x60ek_mmc_defconfig              |    9 +-
> >  configs/sam9x60ek_nandflash_defconfig        |    9 +-
> >  configs/sam9x60ek_qspiflash_defconfig        |    8 +-
> >  drivers/Kconfig                              |    2 +
> >  drivers/Makefile                             |    1 +
> >  drivers/memory/Kconfig                       |    7 +
> >  drivers/memory/Makefile                      |    1 +
> >  drivers/memory/atmel_ebi.c                   |   37 +
> >  drivers/mfd/Kconfig                          |    4 +
> >  drivers/mfd/Makefile                         |    1 +
> >  drivers/mfd/atmel-smc.c                      |  364 +++
> >  drivers/mtd/nand/raw/Kconfig                 |    8 +
> >  drivers/mtd/nand/raw/Makefile                |    1 +
> >  drivers/mtd/nand/raw/atmel/Makefile          |    5 +
> >  drivers/mtd/nand/raw/atmel/nand-controller.c | 2293 ++++++++++++++++++
> >  drivers/mtd/nand/raw/atmel/pmecc.c           |  965 ++++++++
> >  drivers/mtd/nand/raw/atmel/pmecc.h           |   94 +
> >  include/configs/sam9x60ek.h                  |    5 -
> >  include/linux/mfd/syscon/atmel-matrix.h      |  112 +
> >  include/linux/mfd/syscon/atmel-smc.h         |  119 +
> >  24 files changed, 4177 insertions(+), 73 deletions(-)
> >  create mode 100644 drivers/memory/atmel_ebi.c
> >  create mode 100644 drivers/mfd/Kconfig
> >  create mode 100644 drivers/mfd/Makefile
> >  create mode 100644 drivers/mfd/atmel-smc.c
> >  create mode 100644 drivers/mtd/nand/raw/atmel/Makefile
> >  create mode 100644 drivers/mtd/nand/raw/atmel/nand-controller.c
> >  create mode 100644 drivers/mtd/nand/raw/atmel/pmecc.c
> >  create mode 100644 drivers/mtd/nand/raw/atmel/pmecc.h
> >  create mode 100644 include/linux/mfd/syscon/atmel-matrix.h
> >  create mode 100644 include/linux/mfd/syscon/atmel-smc.h
> >
> > --
> > 2.34.1
> >

Once this series is in, I wonder if it might be possible to drop the
nand_init() call and have this happen as needed, i.e. lazy init?

Regards,
Simon