[PATCH v2 04/32] board: mediatek: add MT7981 reference boards

Weijie Gao weijie.gao at mediatek.com
Wed Aug 31 13:00:25 CEST 2022


This patch adds general board files based on MT7981 SoCs.

MT7981 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with spi controller.
So three configs are need for these boot types:

1. mt7981_rfb_defconfig - SPI-NOR and SPI-NAND
2. mt7981_emmc_rfb_defconfig - eMMC only
3. mt7981_sd_rfb_defconfig - SD only

Signed-off-by: Weijie Gao <weijie.gao at mediatek.com>
---
v2 changes:
  Remove mt7981_spim_nand_rfb_defconfig and mt7981_spim_nor_rfb_defconfig
---
 arch/arm/dts/Makefile              |   3 +
 arch/arm/dts/mt7981-emmc-rfb.dts   | 139 +++++++++++++++++++++++
 arch/arm/dts/mt7981-rfb.dts        | 173 +++++++++++++++++++++++++++++
 arch/arm/dts/mt7981-sd-rfb.dts     | 139 +++++++++++++++++++++++
 board/mediatek/mt7981/MAINTAINERS  |  10 ++
 board/mediatek/mt7981/Makefile     |   3 +
 board/mediatek/mt7981/mt7981_rfb.c |  10 ++
 configs/mt7981_emmc_rfb_defconfig  |  64 +++++++++++
 configs/mt7981_rfb_defconfig       |  69 ++++++++++++
 configs/mt7981_sd_rfb_defconfig    |  64 +++++++++++
 include/configs/mt7981.h           |  26 +++++
 11 files changed, 700 insertions(+)
 create mode 100644 arch/arm/dts/mt7981-emmc-rfb.dts
 create mode 100644 arch/arm/dts/mt7981-rfb.dts
 create mode 100644 arch/arm/dts/mt7981-sd-rfb.dts
 create mode 100644 board/mediatek/mt7981/MAINTAINERS
 create mode 100644 board/mediatek/mt7981/Makefile
 create mode 100644 board/mediatek/mt7981/mt7981_rfb.c
 create mode 100644 configs/mt7981_emmc_rfb_defconfig
 create mode 100644 configs/mt7981_rfb_defconfig
 create mode 100644 configs/mt7981_sd_rfb_defconfig
 create mode 100644 include/configs/mt7981.h

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index ee86e467f7..3436b20917 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -1230,6 +1230,9 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
 	mt7622-bananapi-bpi-r64.dtb \
 	mt7623n-bananapi-bpi-r2.dtb \
 	mt7629-rfb.dtb \
+	mt7981-rfb.dtb \
+	mt7981-emmc-rfb.dtb \
+	mt7981-sd-rfb.dtb \
 	mt7986a-rfb.dtb \
 	mt7986b-rfb.dtb \
 	mt7986a-sd-rfb.dtb \
diff --git a/arch/arm/dts/mt7981-emmc-rfb.dts b/arch/arm/dts/mt7981-emmc-rfb.dts
new file mode 100644
index 0000000000..2b7eae99ce
--- /dev/null
+++ b/arch/arm/dts/mt7981-emmc-rfb.dts
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2022 MediaTek Inc.
+ * Author: Sam Shih <sam.shih at mediatek.com>
+ */
+
+/dts-v1/;
+#include "mt7981.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "mt7981-rfb";
+	compatible = "mediatek,mt7981", "mediatek,mt7981-rfb";
+	chosen {
+		stdout-path = &uart0;
+		tick-timer = &timer0;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		  compatible = "regulator-fixed";
+		  regulator-name = "fixed-3.3V";
+		  regulator-min-microvolt = <3300000>;
+		  regulator-max-microvolt = <3300000>;
+		  regulator-boot-on;
+		  regulator-always-on;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&eth {
+	status = "okay";
+	mediatek,gmac-id = <0>;
+	phy-mode = "sgmii";
+	mediatek,switch = "mt7531";
+	reset-gpios = <&gpio 39 GPIO_ACTIVE_HIGH>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&pinctrl {
+	spic_pins: spi1-pins-func-1 {
+		mux {
+			function = "spi";
+			groups = "spi1_1";
+		};
+	};
+
+	uart1_pins: spi1-pins-func-3 {
+		mux {
+			function = "uart";
+			groups = "uart1_2";
+		};
+	};
+
+	/* pin15 as pwm0 */
+	one_pwm_pins: one-pwm-pins {
+		mux {
+			function = "pwm";
+			groups = "pwm0_1";
+		};
+	};
+
+	/* pin15 as pwm0 and pin14 as pwm1 */
+	two_pwm_pins: two-pwm-pins {
+		mux {
+			function = "pwm";
+			groups = "pwm0_1", "pwm1_0";
+		};
+	};
+
+	/* pin15 as pwm0, pin14 as pwm1, pin7 as pwm2 */
+	three_pwm_pins: three-pwm-pins {
+		mux {
+			function = "pwm";
+			groups = "pwm0_1", "pwm1_0", "pwm2";
+		};
+	};
+
+	mmc0_pins_default: mmc0default {
+		mux {
+			function = "flash";
+			groups =  "emmc_45";
+		};
+		conf-cmd-dat {
+			pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO",
+				"SPI0_CS",  "SPI0_HOLD", "SPI0_WP",
+				"SPI1_CLK", "SPI1_MOSI", "SPI1_MISO";
+			input-enable;
+			drive-strength = <MTK_DRIVE_4mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+		conf-clk {
+			pins = "SPI1_CS";
+			drive-strength = <MTK_DRIVE_6mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+		conf-rst {
+			pins = "PWM0";
+			drive-strength = <MTK_DRIVE_4mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&two_pwm_pins>;
+	status = "okay";
+};
+
+&watchdog {
+	status = "disabled";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_default>;
+	bus-width = <8>;
+	max-frequency = <52000000>;
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	vmmc-supply = <&reg_3p3v>;
+	non-removable;
+	status = "okay";
+};
diff --git a/arch/arm/dts/mt7981-rfb.dts b/arch/arm/dts/mt7981-rfb.dts
new file mode 100644
index 0000000000..5559ace953
--- /dev/null
+++ b/arch/arm/dts/mt7981-rfb.dts
@@ -0,0 +1,173 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2022 MediaTek Inc.
+ * Author: Sam Shih <sam.shih at mediatek.com>
+ */
+
+/dts-v1/;
+#include "mt7981.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "mt7981-rfb";
+	compatible = "mediatek,mt7981", "mediatek,mt7981-rfb";
+	chosen {
+		stdout-path = &uart0;
+		tick-timer = &timer0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&eth {
+	status = "okay";
+	mediatek,gmac-id = <0>;
+	phy-mode = "sgmii";
+	mediatek,switch = "mt7531";
+	reset-gpios = <&gpio 39 GPIO_ACTIVE_HIGH>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&pinctrl {
+	spi_flash_pins: spi0-pins-func-1 {
+		mux {
+			function = "flash";
+			groups = "spi0", "spi0_wp_hold";
+		};
+
+		conf-pu {
+			pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+		};
+
+		conf-pd {
+			pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+		};
+	};
+
+	spi2_flash_pins: spi2-spi2-pins {
+		mux {
+			function = "spi";
+			groups = "spi2", "spi2_wp_hold";
+		};
+
+		conf-pu {
+			pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_00>;
+		};
+
+		conf-pd {
+			pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_00>;
+		};
+	};
+
+	spic_pins: spi1-pins-func-1 {
+		mux {
+			function = "spi";
+			groups = "spi1_1";
+		};
+	};
+
+	uart1_pins: spi1-pins-func-3 {
+		mux {
+			function = "uart";
+			groups = "uart1_2";
+		};
+	};
+
+	/* pin15 as pwm0 */
+	one_pwm_pins: one-pwm-pins {
+		mux {
+			function = "pwm";
+			groups = "pwm0_1";
+		};
+	};
+
+	/* pin15 as pwm0 and pin14 as pwm1 */
+	two_pwm_pins: two-pwm-pins {
+		mux {
+			function = "pwm";
+			groups = "pwm0_1", "pwm1_0";
+		};
+	};
+
+	/* pin15 as pwm0, pin14 as pwm1, pin7 as pwm2 */
+	three_pwm_pins: three-pwm-pins {
+		mux {
+			function = "pwm";
+			groups = "pwm0_1", "pwm1_0", "pwm2";
+		};
+	};
+};
+
+&spi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	status = "okay";
+	must_tx;
+	enhance_timing;
+	dma_ext;
+	ipm_design;
+	support_quad;
+	tick_dly = <2>;
+	sample_sel = <0>;
+
+	spi_nand at 0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-max-frequency = <52000000>;
+	};
+};
+
+&spi2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_flash_pins>;
+	status = "okay";
+	must_tx;
+	enhance_timing;
+	dma_ext;
+	ipm_design;
+	support_quad;
+	tick_dly = <2>;
+	sample_sel = <0>;
+
+	spi_nor at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <52000000>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&two_pwm_pins>;
+	status = "okay";
+};
+
+&watchdog {
+	status = "disabled";
+};
diff --git a/arch/arm/dts/mt7981-sd-rfb.dts b/arch/arm/dts/mt7981-sd-rfb.dts
new file mode 100644
index 0000000000..34ac227ecf
--- /dev/null
+++ b/arch/arm/dts/mt7981-sd-rfb.dts
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2022 MediaTek Inc.
+ * Author: Sam Shih <sam.shih at mediatek.com>
+ */
+
+/dts-v1/;
+#include "mt7981.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "mt7981-rfb";
+	compatible = "mediatek,mt7981", "mediatek,mt7981-sd-rfb";
+	chosen {
+		stdout-path = &uart0;
+		tick-timer = &timer0;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		  compatible = "regulator-fixed";
+		  regulator-name = "fixed-3.3V";
+		  regulator-min-microvolt = <3300000>;
+		  regulator-max-microvolt = <3300000>;
+		  regulator-boot-on;
+		  regulator-always-on;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&eth {
+	status = "okay";
+	mediatek,gmac-id = <0>;
+	phy-mode = "sgmii";
+	mediatek,switch = "mt7531";
+	reset-gpios = <&gpio 39 GPIO_ACTIVE_HIGH>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&pinctrl {
+	spic_pins: spi1-pins-func-1 {
+		mux {
+			function = "spi";
+			groups = "spi1_1";
+		};
+	};
+
+	uart1_pins: spi1-pins-func-3 {
+		mux {
+			function = "uart";
+			groups = "uart1_2";
+		};
+	};
+
+	/* pin15 as pwm0 */
+	one_pwm_pins: one-pwm-pins {
+		mux {
+			function = "pwm";
+			groups = "pwm0_1";
+		};
+	};
+
+	/* pin15 as pwm0 and pin14 as pwm1 */
+	two_pwm_pins: two-pwm-pins {
+		mux {
+			function = "pwm";
+			groups = "pwm0_1", "pwm1_0";
+		};
+	};
+
+	/* pin15 as pwm0, pin14 as pwm1, pin7 as pwm2 */
+	three_pwm_pins: three-pwm-pins {
+		mux {
+			function = "pwm";
+			groups = "pwm0_1", "pwm1_0", "pwm2";
+		};
+	};
+
+	mmc0_pins_default: mmc0default {
+		mux {
+			function = "flash";
+			groups =  "emmc_45";
+		};
+		conf-cmd-dat {
+			pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO",
+				"SPI0_CS",  "SPI0_HOLD", "SPI0_WP",
+				"SPI1_CLK", "SPI1_MOSI", "SPI1_MISO";
+			input-enable;
+			drive-strength = <MTK_DRIVE_4mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+		conf-clk {
+			pins = "SPI1_CS";
+			drive-strength = <MTK_DRIVE_6mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+		conf-rst {
+			pins = "PWM0";
+			drive-strength = <MTK_DRIVE_4mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&two_pwm_pins>;
+	status = "okay";
+};
+
+&watchdog {
+	status = "disabled";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_default>;
+	bus-width = <4>;
+	max-frequency = <52000000>;
+	cap-sd-highspeed;
+	r_smpl = <0>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
diff --git a/board/mediatek/mt7981/MAINTAINERS b/board/mediatek/mt7981/MAINTAINERS
new file mode 100644
index 0000000000..e7592a7a54
--- /dev/null
+++ b/board/mediatek/mt7981/MAINTAINERS
@@ -0,0 +1,10 @@
+MT7981
+M:	Sam Shih <sam.shih at mediatek.com>
+S:	Maintained
+F:	board/mediatek/mt7981
+F:	include/configs/mt7981.h
+F:	configs/mt7981_emmc_rfb_defconfig
+F:	configs/mt7981_rfb_defconfig
+F:	configs/mt7981_sd_rfb_defconfig
+F:	configs/mt7981_spim_nand_rfb_defconfig
+F:	configs/mt7981_spim_nor_rfb_defconfig
diff --git a/board/mediatek/mt7981/Makefile b/board/mediatek/mt7981/Makefile
new file mode 100644
index 0000000000..fa5990ffb2
--- /dev/null
+++ b/board/mediatek/mt7981/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier:	GPL-2.0
+
+obj-y	+= mt7981_rfb.o
diff --git a/board/mediatek/mt7981/mt7981_rfb.c b/board/mediatek/mt7981/mt7981_rfb.c
new file mode 100644
index 0000000000..846c715ca0
--- /dev/null
+++ b/board/mediatek/mt7981/mt7981_rfb.c
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 MediaTek Inc.
+ * Author: Sam Shih <sam.shih at mediatek.com>
+ */
+
+int board_init(void)
+{
+	return 0;
+}
diff --git a/configs/mt7981_emmc_rfb_defconfig b/configs/mt7981_emmc_rfb_defconfig
new file mode 100644
index 0000000000..5f9f6d8582
--- /dev/null
+++ b/configs/mt7981_emmc_rfb_defconfig
@@ -0,0 +1,64 @@
+CONFIG_ARM=y
+CONFIG_POSITION_INDEPENDENT=y
+CONFIG_ARCH_MEDIATEK=y
+CONFIG_SYS_TEXT_BASE=0x41e00000
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x80000
+CONFIG_ENV_OFFSET=0x300000
+CONFIG_DEFAULT_DEVICE_TREE="mt7981-emmc-rfb"
+CONFIG_TARGET_MT7981=y
+CONFIG_DEBUG_UART_BASE=0x11002000
+CONFIG_DEBUG_UART_CLOCK=40000000
+CONFIG_SYS_LOAD_ADDR=0x46000000
+CONFIG_DEBUG_UART=y
+# CONFIG_AUTOBOOT is not set
+CONFIG_DEFAULT_FDT_FILE="mt7981-emmc-rfb"
+CONFIG_LOGLEVEL=7
+CONFIG_LOG=y
+CONFIG_SYS_PROMPT="MT7981> "
+CONFIG_SYS_CBSIZE=512
+CONFIG_SYS_PBSIZE=1049
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_BOOTM_VXWORKS is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_UNLZ4 is not set
+# CONFIG_CMD_UNZIP is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_GPT_RENAME=y
+CONFIG_CMD_LSBLK=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_READ=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_SMC=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_PARTITION_TYPE_GUID=y
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_CLK=y
+CONFIG_MMC_HS200_SUPPORT=y
+CONFIG_MMC_MTK=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_MEDIATEK_ETH=y
+CONFIG_PINCTRL=y
+CONFIG_PINCONF=y
+CONFIG_PINCTRL_MT7981=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MTK_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_SERIAL=y
+CONFIG_MTK_SERIAL=y
+CONFIG_FAT_WRITE=y
+CONFIG_HEXDUMP=y
+# CONFIG_EFI_LOADER is not set
diff --git a/configs/mt7981_rfb_defconfig b/configs/mt7981_rfb_defconfig
new file mode 100644
index 0000000000..88299e3e51
--- /dev/null
+++ b/configs/mt7981_rfb_defconfig
@@ -0,0 +1,69 @@
+CONFIG_ARM=y
+CONFIG_POSITION_INDEPENDENT=y
+CONFIG_ARCH_MEDIATEK=y
+CONFIG_SYS_TEXT_BASE=0x41e00000
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEFAULT_DEVICE_TREE="mt7981-rfb"
+CONFIG_TARGET_MT7981=y
+CONFIG_DEBUG_UART_BASE=0x11002000
+CONFIG_DEBUG_UART_CLOCK=40000000
+CONFIG_SYS_LOAD_ADDR=0x46000000
+CONFIG_DEBUG_UART=y
+# CONFIG_AUTOBOOT is not set
+CONFIG_DEFAULT_FDT_FILE="mt7981-rfb"
+CONFIG_LOGLEVEL=7
+CONFIG_LOG=y
+CONFIG_SYS_PROMPT="MT7981> "
+CONFIG_SYS_CBSIZE=512
+CONFIG_SYS_PBSIZE=1049
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_BOOTM_VXWORKS is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_UNLZ4 is not set
+# CONFIG_CMD_UNZIP is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_SF_TEST=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_SMC=y
+CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_BLK=y
+CONFIG_HAVE_BLOCK_DEVICE=y
+CONFIG_CLK=y
+# CONFIG_MMC is not set
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_MTD_SPI_NAND=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_EON=y
+CONFIG_SPI_FLASH_GIGADEVICE=y
+CONFIG_SPI_FLASH_ISSI=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_SPI_FLASH_XMC=y
+CONFIG_SPI_FLASH_XTX=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_MEDIATEK_ETH=y
+CONFIG_PINCTRL=y
+CONFIG_PINCONF=y
+CONFIG_PINCTRL_MT7981=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MTK_POWER_DOMAIN=y
+CONFIG_DM_SERIAL=y
+CONFIG_MTK_SERIAL=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_MTK_SPIM=y
+CONFIG_HEXDUMP=y
+# CONFIG_EFI_LOADER is not set
diff --git a/configs/mt7981_sd_rfb_defconfig b/configs/mt7981_sd_rfb_defconfig
new file mode 100644
index 0000000000..b5c765bd7c
--- /dev/null
+++ b/configs/mt7981_sd_rfb_defconfig
@@ -0,0 +1,64 @@
+CONFIG_ARM=y
+CONFIG_POSITION_INDEPENDENT=y
+CONFIG_ARCH_MEDIATEK=y
+CONFIG_SYS_TEXT_BASE=0x41e00000
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x80000
+CONFIG_ENV_OFFSET=0x300000
+CONFIG_DEFAULT_DEVICE_TREE="mt7981-sd-rfb"
+CONFIG_TARGET_MT7981=y
+CONFIG_DEBUG_UART_BASE=0x11002000
+CONFIG_DEBUG_UART_CLOCK=40000000
+CONFIG_SYS_LOAD_ADDR=0x46000000
+CONFIG_DEBUG_UART=y
+# CONFIG_AUTOBOOT is not set
+CONFIG_DEFAULT_FDT_FILE="mt7981-sd-rfb"
+CONFIG_LOGLEVEL=7
+CONFIG_LOG=y
+CONFIG_SYS_PROMPT="MT7981> "
+CONFIG_SYS_CBSIZE=512
+CONFIG_SYS_PBSIZE=1049
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_BOOTM_VXWORKS is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_UNLZ4 is not set
+# CONFIG_CMD_UNZIP is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_GPT_RENAME=y
+CONFIG_CMD_LSBLK=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_READ=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_SMC=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_PARTITION_TYPE_GUID=y
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_CLK=y
+CONFIG_MMC_HS200_SUPPORT=y
+CONFIG_MMC_MTK=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_MEDIATEK_ETH=y
+CONFIG_PINCTRL=y
+CONFIG_PINCONF=y
+CONFIG_PINCTRL_MT7981=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MTK_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_SERIAL=y
+CONFIG_MTK_SERIAL=y
+CONFIG_FAT_WRITE=y
+CONFIG_HEXDUMP=y
+# CONFIG_EFI_LOADER is not set
diff --git a/include/configs/mt7981.h b/include/configs/mt7981.h
new file mode 100644
index 0000000000..a213b8de88
--- /dev/null
+++ b/include/configs/mt7981.h
@@ -0,0 +1,26 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Configuration for MediaTek MT7981 SoC
+ *
+ * Copyright (C) 2022 MediaTek Inc.
+ * Author: Sam Shih <sam.shih at mediatek.com>
+ */
+
+#ifndef __MT7981_H
+#define __MT7981_H
+
+#include <linux/sizes.h>
+
+#define CONFIG_SYS_NONCACHED_MEMORY	SZ_1M
+#define CONFIG_SYS_MMC_ENV_DEV		0
+
+/* Uboot definition */
+#define CONFIG_SYS_UBOOT_BASE		CONFIG_SYS_TEXT_BASE
+
+/* SPL -> Uboot */
+#define CONFIG_SYS_UBOOT_START		CONFIG_SYS_TEXT_BASE
+
+/* DRAM */
+#define CONFIG_SYS_SDRAM_BASE		0x40000000
+
+#endif
-- 
2.17.1



More information about the U-Boot mailing list