[PATCH 21/41] global: Remove unused CONFIG symbols

Tom Rini trini at konsulko.com
Fri Dec 2 22:42:31 CET 2022


This removes the following unreferenced CONFIG symbols:
   CONFIG_FDTADDR
   CONFIG_FDTFILE
   CONFIG_FLASH_SECTOR_SIZE
   CONFIG_FSL_CPLD
   CONFIG_HDMI_ENCODER_I2C_ADDR
   CONFIG_I2C_MVTWSI
   CONFIG_I2C_RTC_ADDR
   CONFIG_IRAM_END
   CONFIG_IRAM_SIZE
   CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
   CONFIG_L1_INIT_RAM
   CONFIG_MACB_SEARCH_PHY
   CONFIG_MIU_2BIT_21_7_INTERLEAVED
   CONFIG_MTD_NAND_VERIFY_WRITE
   CONFIG_MVGBE_PORTS
   CONFIG_NETDEV
   CONFIG_NUM_DSP_CPUS
   CONFIG_PHY_BASE_ADR
   CONFIG_PHY_INTERFACE_MODE
   CONFIG_PSRAM_SCFG
   CONFIG_RAMBOOT_SPIFLASH
   CONFIG_RAMBOOT_TEXT_BASE
   CONFIG_RD_LVL
   CONFIG_ROCKCHIP_SDHCI_MAX_FREQ
   CONFIG_SETUP_INITRD_TAG
   CONFIG_SH_QSPI_BASE
   CONFIG_SMDK5420
   CONFIG_SOCRATES
   CONFIG_SPI_ADDR
   CONFIG_SPI_FLASH_QUAD
   CONFIG_SPI_FLASH_SIZE
   CONFIG_SPI_HALF_DUPLEX
   CONFIG_SPI_N25Q256A_RESET
   CONFIG_TEGRA_SLINK_CTRLS
   CONFIG_TPM_TIS_BASE_ADDRESS
   CONFIG_UBOOT_SECTOR_COUNT
   CONFIG_UBOOT_SECTOR_START
   CONFIG_VAR_SIZE_SPL
   CONFIG_VERY_BIG_RAM

And also:
   BL1_SIZE
   PHY_NO
   RESERVE_BLOCK_SIZE

Signed-off-by: Tom Rini <trini at konsulko.com>
---
 README                                     | 11 -----------
 arch/arm/include/asm/arch-ls102xa/config.h |  1 -
 arch/arm/mach-mvebu/include/mach/config.h  |  9 ---------
 arch/powerpc/include/asm/config_mpc85xx.h  |  1 -
 arch/xtensa/include/asm/config.h           |  1 -
 board/Marvell/openrd/openrd.c              |  2 +-
 drivers/net/mvgbe.c                        |  4 ----
 drivers/net/mvgbe.h                        |  7 -------
 drivers/ram/mpc83xx_sdram.c                |  7 +------
 include/configs/MPC837XERDB.h              |  8 +++-----
 include/configs/P1010RDB.h                 |  1 -
 include/configs/P2041RDB.h                 |  9 ++-------
 include/configs/SBx81LIFKW.h               |  9 ---------
 include/configs/SBx81LIFXCAT.h             |  9 ---------
 include/configs/T102xRDB.h                 |  2 --
 include/configs/T104xRDB.h                 |  4 ----
 include/configs/T208xQDS.h                 |  2 --
 include/configs/T208xRDB.h                 |  2 --
 include/configs/T4240RDB.h                 |  3 ---
 include/configs/alt.h                      |  3 ---
 include/configs/ax25-ae350.h               |  3 ---
 include/configs/beaver.h                   |  4 ----
 include/configs/blanche.h                  |  4 +---
 include/configs/cardhu.h                   |  4 ----
 include/configs/cei-tk1-som.h              |  3 ---
 include/configs/colibri_vf.h               |  4 ----
 include/configs/dalmore.h                  |  3 ---
 include/configs/dns325.h                   |  7 -------
 include/configs/dockstar.h                 |  6 ------
 include/configs/dra7xx_evm.h               |  1 -
 include/configs/dreamplug.h                |  6 ------
 include/configs/ds109.h                    |  8 --------
 include/configs/eb_cpu5282.h               |  8 --------
 include/configs/efi-x86_app.h              |  2 --
 include/configs/embestmx6boards.h          |  6 +++---
 include/configs/ethernut5.h                |  1 -
 include/configs/exynos5-common.h           |  2 --
 include/configs/exynos5420-common.h        |  2 --
 include/configs/exynos7420-common.h        |  4 ----
 include/configs/goflexhome.h               |  6 ------
 include/configs/guruplug.h                 |  8 --------
 include/configs/ib62x0.h                   |  8 --------
 include/configs/iconnect.h                 | 10 ----------
 include/configs/jetson-tk1.h               |  5 -----
 include/configs/k2e_evm.h                  |  1 -
 include/configs/k2g_evm.h                  |  1 -
 include/configs/k2l_evm.h                  |  1 -
 include/configs/kmcent2.h                  |  1 -
 include/configs/kontron_sl28.h             |  1 -
 include/configs/lacie_kw.h                 |  7 -------
 include/configs/legoev3.h                  |  1 -
 include/configs/ls1028a_common.h           |  1 -
 include/configs/ls1043a_common.h           |  1 -
 include/configs/ls1043aqds.h               |  1 -
 include/configs/ls1043ardb.h               |  1 -
 include/configs/ls1046a_common.h           |  1 -
 include/configs/ls1046afrwy.h              |  1 -
 include/configs/ls1046aqds.h               |  1 -
 include/configs/ls1046ardb.h               |  1 -
 include/configs/ls1088a_common.h           |  1 -
 include/configs/ls1088aqds.h               |  1 -
 include/configs/ls1088ardb.h               |  1 -
 include/configs/ls2080a_common.h           |  1 -
 include/configs/ls2080aqds.h               |  1 -
 include/configs/ls2080ardb.h               |  1 -
 include/configs/lx2160a_common.h           |  1 -
 include/configs/malta.h                    |  2 --
 include/configs/mt7621.h                   |  1 -
 include/configs/mt7629.h                   |  5 +----
 include/configs/mxs.h                      |  5 -----
 include/configs/nas220.h                   | 12 ------------
 include/configs/nsa310s.h                  |  4 ----
 include/configs/nyan-big.h                 |  3 ---
 include/configs/openrd.h                   | 22 ----------------------
 include/configs/origen.h                   |  6 ------
 include/configs/p2371-0000.h               |  3 ---
 include/configs/p2371-2180.h               |  3 ---
 include/configs/p2571.h                    |  3 ---
 include/configs/p3450-0000.h               |  3 ---
 include/configs/pm9263.h                   |  5 -----
 include/configs/pogo_e02.h                 |  6 ------
 include/configs/pogo_v4.h                  |  6 ------
 include/configs/porter.h                   |  3 ---
 include/configs/qemu-ppce500.h             |  1 -
 include/configs/rcar-gen3-common.h         |  1 -
 include/configs/rk3399_common.h            | 10 ----------
 include/configs/sheevaplug.h               |  6 ------
 include/configs/silk.h                     |  3 ---
 include/configs/smdk5420.h                 |  2 --
 include/configs/smdkv310.h                 |  3 ---
 include/configs/socfpga_sr1500.h           |  6 ------
 include/configs/socrates.h                 |  4 ----
 include/configs/stout.h                    |  3 ---
 include/configs/synquacer.h                |  1 -
 include/configs/tec-ng.h                   |  6 ------
 include/configs/venice2.h                  |  3 ---
 include/configs/vinco.h                    |  3 ---
 include/configs/x86-common.h               | 16 ----------------
 include/configs/xpress.h                   |  7 ++-----
 99 files changed, 14 insertions(+), 391 deletions(-)

diff --git a/README b/README
index 120963317608..9e2627863ce5 100644
--- a/README
+++ b/README
@@ -373,12 +373,6 @@ The following options need to be configured:
 		such as ARM architectural timer initialization.
 
 - Linux Kernel Interface:
-		CONFIG_MEMSIZE_IN_BYTES		[relevant for MIPS only]
-
-		When transferring memsize parameter to Linux, some versions
-		expect it to be in bytes, others in MB.
-		Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
-
 		CONFIG_OF_LIBFDT
 
 		New kernel versions are expecting firmware settings to be
@@ -585,11 +579,6 @@ The following options need to be configured:
 		Support for generic parallel port TPM devices. Only one device
 		per system is supported at this time.
 
-			CONFIG_TPM_TIS_BASE_ADDRESS
-			Base address where the generic TPM device is mapped
-			to. Contemporary x86 systems usually map it at
-			0xfed40000.
-
 		CONFIG_TPM
 		Define this to enable the TPM support library which provides
 		functional interfaces to some TPM commands.
diff --git a/arch/arm/include/asm/arch-ls102xa/config.h b/arch/arm/include/asm/arch-ls102xa/config.h
index 14f86df5ed5a..4a4d64244148 100644
--- a/arch/arm/include/asm/arch-ls102xa/config.h
+++ b/arch/arm/include/asm/arch-ls102xa/config.h
@@ -70,7 +70,6 @@
 /* SATA */
 #define AHCI_BASE_ADDR				(CONFIG_SYS_IMMR + 0x02200000)
 #ifdef CONFIG_DDR_SPD
-#define CONFIG_VERY_BIG_RAM
 #define CONFIG_MAX_MEM_MAPPED			((phys_size_t)2 << 30)
 #endif
 
diff --git a/arch/arm/mach-mvebu/include/mach/config.h b/arch/arm/mach-mvebu/include/mach/config.h
index 2e06f2bdaee3..96a08104ff46 100644
--- a/arch/arm/mach-mvebu/include/mach/config.h
+++ b/arch/arm/mach-mvebu/include/mach/config.h
@@ -30,13 +30,4 @@
 /* Needed for SPI NOR booting in SPL */
 #define CONFIG_DM_SEQ_ALIAS		1
 
-/*
- * I2C related stuff
- */
-#ifdef CONFIG_CMD_I2C
-#ifndef CONFIG_SYS_I2C_SOFT
-#define CONFIG_I2C_MVTWSI
-#endif
-#endif
-
 #endif /* __MVEBU_CONFIG_H */
diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h
index edaf8baaaebe..e80599106066 100644
--- a/arch/powerpc/include/asm/config_mpc85xx.h
+++ b/arch/powerpc/include/asm/config_mpc85xx.h
@@ -133,7 +133,6 @@
 #define CFG_SYS_FM_MURAM_SIZE	0x60000
 
 #ifdef CONFIG_ARCH_B4860
-#define CONFIG_NUM_DSP_CPUS		6
 #define CFG_SYS_FSL_CLUSTER_CLOCKS	{ 1, 4, 4, 4 }
 #define CFG_SYS_NUM_FM1_DTSEC	6
 #define CFG_SYS_NUM_FM1_10GEC	2
diff --git a/arch/xtensa/include/asm/config.h b/arch/xtensa/include/asm/config.h
index a1096ab1961b..21b334b93896 100644
--- a/arch/xtensa/include/asm/config.h
+++ b/arch/xtensa/include/asm/config.h
@@ -14,7 +14,6 @@
  * restricting used physical memory to the first 128MB.
  */
 #if XCHAL_HAVE_PTP_MMU
-#define CONFIG_VERY_BIG_RAM
 #define CONFIG_MAX_MEM_MAPPED (128 << 20)
 #endif
 
diff --git a/board/Marvell/openrd/openrd.c b/board/Marvell/openrd/openrd.c
index f44ac3315ebc..581e2e084d6f 100644
--- a/board/Marvell/openrd/openrd.c
+++ b/board/Marvell/openrd/openrd.c
@@ -140,7 +140,7 @@ void mv_phy_init(char *name)
 	/* reset the phy */
 	miiphy_reset(name, devadr);
 
-	printf(PHY_NO" Initialized on %s\n", name);
+	printf("Initialized on %s\n", name);
 }
 
 void reset_phy(void)
diff --git a/drivers/net/mvgbe.c b/drivers/net/mvgbe.c
index 58363fce0570..3587ca2124e3 100644
--- a/drivers/net/mvgbe.c
+++ b/drivers/net/mvgbe.c
@@ -37,10 +37,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#ifndef CONFIG_MVGBE_PORTS
-# define CONFIG_MVGBE_PORTS {0, 0}
-#endif
-
 #define MV_PHY_ADR_REQUEST 0xee
 #define MVGBE_SMI_REG (((struct mvgbe_registers *)MVGBE0_BASE)->smi)
 #define MVGBE_PGADR_REG	22
diff --git a/drivers/net/mvgbe.h b/drivers/net/mvgbe.h
index e3f5ac06399d..6514ab67bab9 100644
--- a/drivers/net/mvgbe.h
+++ b/drivers/net/mvgbe.h
@@ -11,13 +11,6 @@
 #ifndef __MVGBE_H__
 #define __MVGBE_H__
 
-/* PHY_BASE_ADR is board specific and can be configured */
-#if defined (CONFIG_PHY_BASE_ADR)
-#define PHY_BASE_ADR		CONFIG_PHY_BASE_ADR
-#else
-#define PHY_BASE_ADR		0x08	/* default phy base addr */
-#endif
-
 /* Constants */
 #define INT_CAUSE_UNMASK_ALL		0x0007ffff
 #define INT_CAUSE_UNMASK_ALL_EXT	0x0011ffff
diff --git a/drivers/ram/mpc83xx_sdram.c b/drivers/ram/mpc83xx_sdram.c
index a53ff93a6b06..11676d4fae7e 100644
--- a/drivers/ram/mpc83xx_sdram.c
+++ b/drivers/ram/mpc83xx_sdram.c
@@ -118,12 +118,7 @@ int dram_init(void)
 
 phys_size_t get_effective_memsize(void)
 {
-	if (!IS_ENABLED(CONFIG_VERY_BIG_RAM))
-		return gd->ram_size;
-
-	/* Limit stack to what we can reasonable map */
-	return ((gd->ram_size > CONFIG_MAX_MEM_MAPPED) ?
-		CONFIG_MAX_MEM_MAPPED : gd->ram_size);
+	return gd->ram_size;
 }
 
 /**
diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h
index 7dff3cc69136..7b932eb38901 100644
--- a/include/configs/MPC837XERDB.h
+++ b/include/configs/MPC837XERDB.h
@@ -195,12 +195,10 @@
  * Environment Configuration
  */
 
-#define CONFIG_NETDEV		"eth1"
-
-#define CONFIG_FDTFILE		"mpc8379_rdb.dtb"
+#define FDTFILE			"mpc8379_rdb.dtb"
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
-	"netdev=" CONFIG_NETDEV "\0"				\
+	"netdev=eth1\0"				\
 	"uboot=" CONFIG_UBOOTPATH "\0"					\
 	"tftpflash=tftp $loadaddr $uboot;"				\
 		"protect off " __stringify(CONFIG_TEXT_BASE)	\
@@ -214,7 +212,7 @@
 		"cmp.b $loadaddr " __stringify(CONFIG_TEXT_BASE)	\
 			" $filesize\0"	\
 	"fdtaddr=780000\0"						\
-	"fdtfile=" CONFIG_FDTFILE "\0"					\
+	"fdtfile=" FDTFILE "\0"					\
 	"ramdiskaddr=1000000\0"						\
 	"ramdiskfile=rootfs.ext2.gz.uboot\0"				\
 	"console=ttyS0\0"						\
diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h
index d83563d6181d..02d49c3d3407 100644
--- a/include/configs/P1010RDB.h
+++ b/include/configs/P1010RDB.h
@@ -24,7 +24,6 @@
 
 #ifdef CONFIG_SPIFLASH
 #ifdef CONFIG_NXP_ESBC
-#define CONFIG_RAMBOOT_SPIFLASH
 #define CONFIG_RESET_VECTOR_ADDRESS	0x110bfffc
 #else
 #define CFG_SYS_SPI_FLASH_U_BOOT_SIZE	(512 << 10)
diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h
index 0f0cdb3a6815..1a157a7da05d 100644
--- a/include/configs/P2041RDB.h
+++ b/include/configs/P2041RDB.h
@@ -12,7 +12,6 @@
 #define __CONFIG_H
 
 #ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_TEXT_BASE
 #define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
 #endif
 
@@ -46,10 +45,9 @@
 /*
  *  Config the L3 Cache as L3 SRAM
  */
-#define CFG_SYS_INIT_L3_ADDR		CONFIG_RAMBOOT_TEXT_BASE
+#define CFG_SYS_INIT_L3_ADDR		CONFIG_TEXT_BASE
 #ifdef CONFIG_PHYS_64BIT
-#define CFG_SYS_INIT_L3_ADDR_PHYS	(0xf00000000ull | \
-		CONFIG_RAMBOOT_TEXT_BASE)
+#define CFG_SYS_INIT_L3_ADDR_PHYS	(0xf00000000ull | CONFIG_TEXT_BASE)
 #else
 #define CFG_SYS_INIT_L3_ADDR_PHYS	CFG_SYS_INIT_L3_ADDR
 #endif
@@ -62,7 +60,6 @@
 /*
  * DDR Setup
  */
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
 
@@ -88,7 +85,6 @@
 #define CFG_SYS_FLASH_BASE_PHYS	CFG_SYS_FLASH_BASE
 #endif
 
-#define CONFIG_FSL_CPLD
 #define CPLD_BASE		0xffdf0000	/* CPLD registers */
 #ifdef CONFIG_PHYS_64BIT
 #define CPLD_BASE_PHYS		0xfffdf0000ull
@@ -131,7 +127,6 @@
 #define CFG_SYS_FLASH_BANKS_LIST	{CFG_SYS_FLASH_BASE_PHYS + 0x8000000}
 
 /* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
 #define CFG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
 #ifdef CONFIG_PHYS_64BIT
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
diff --git a/include/configs/SBx81LIFKW.h b/include/configs/SBx81LIFKW.h
index bad34d9771ec..eb302348800b 100644
--- a/include/configs/SBx81LIFKW.h
+++ b/include/configs/SBx81LIFKW.h
@@ -37,14 +37,5 @@
 /* size in bytes reserved for initial data */
 
 #include <asm/arch/config.h>
-/* There is no PHY directly connected so don't ask it for link status */
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable a single port */
-#define CONFIG_PHY_BASE_ADR	0x01
-#endif /* CONFIG_CMD_NET */
 
 #endif /* _CONFIG_SBX81LIFKW_H */
diff --git a/include/configs/SBx81LIFXCAT.h b/include/configs/SBx81LIFXCAT.h
index 9a9663b34ba8..8c5e81aebd9b 100644
--- a/include/configs/SBx81LIFXCAT.h
+++ b/include/configs/SBx81LIFXCAT.h
@@ -42,14 +42,5 @@
 /* size in bytes reserved for initial data */
 
 #include <asm/arch/config.h>
-/* There is no PHY directly connected so don't ask it for link status */
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable a single port */
-#define CONFIG_PHY_BASE_ADR	0x01
-#endif /* CONFIG_CMD_NET */
 
 #endif /* _CONFIG_SBX81LIFXCAT_H */
diff --git a/include/configs/T102xRDB.h b/include/configs/T102xRDB.h
index e815d9f81a1e..4b443c750425 100644
--- a/include/configs/T102xRDB.h
+++ b/include/configs/T102xRDB.h
@@ -112,7 +112,6 @@
 /*
  * DDR Setup
  */
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
 #if defined(CONFIG_TARGET_T1024RDB)
@@ -269,7 +268,6 @@
 #endif
 
 /* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
 #define CFG_SYS_INIT_RAM_ADDR	0xfdd00000	/* Initial L1 address */
 #ifdef CONFIG_PHYS_64BIT
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
diff --git a/include/configs/T104xRDB.h b/include/configs/T104xRDB.h
index 6fe0bd682801..dfad76e16f11 100644
--- a/include/configs/T104xRDB.h
+++ b/include/configs/T104xRDB.h
@@ -86,7 +86,6 @@
 /*
  * DDR Setup
  */
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
 
@@ -247,7 +246,6 @@
 #endif
 
 /* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
 #define CFG_SYS_INIT_RAM_ADDR	0xfdd00000	/* Initial L1 address */
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe03c000
@@ -285,8 +283,6 @@
  */
 #define CFG_SYS_I2C_RTC_ADDR         0x68
 
-/*DVI encoder*/
-#define CONFIG_HDMI_ENCODER_I2C_ADDR  0x75
 #endif
 
 /*
diff --git a/include/configs/T208xQDS.h b/include/configs/T208xQDS.h
index 79b3d7af4eac..24c1daf9985f 100644
--- a/include/configs/T208xQDS.h
+++ b/include/configs/T208xQDS.h
@@ -78,7 +78,6 @@
 /*
  * DDR Setup
  */
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
 #define CFG_SYS_SDRAM_SIZE	2048	/* for fixed parameter use */
@@ -245,7 +244,6 @@
 #endif
 
 /* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
 #define CFG_SYS_INIT_RAM_ADDR	0xfdd00000 /* Initial L1 address */
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe03c000
diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h
index 2a32fe37aa92..c825e7fa0c65 100644
--- a/include/configs/T208xRDB.h
+++ b/include/configs/T208xRDB.h
@@ -78,7 +78,6 @@
 /*
  * DDR Setup
  */
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
 #define CFG_SYS_SDRAM_SIZE	2048	/* for fixed parameter use */
@@ -210,7 +209,6 @@
 #endif
 
 /* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
 #define CFG_SYS_INIT_RAM_ADDR	0xfdd00000 /* Initial L1 address */
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe03c000
diff --git a/include/configs/T4240RDB.h b/include/configs/T4240RDB.h
index d8c4de5b3d73..95735f3fcb1e 100644
--- a/include/configs/T4240RDB.h
+++ b/include/configs/T4240RDB.h
@@ -16,7 +16,6 @@
 
 #ifdef CONFIG_RAMBOOT_PBL
 #ifndef CONFIG_SDCARD
-#define CONFIG_RAMBOOT_TEXT_BASE        CONFIG_TEXT_BASE
 #define CONFIG_RESET_VECTOR_ADDRESS     0xfffffffc
 #else
 #define RESET_VECTOR_OFFSET		0x27FFC
@@ -60,7 +59,6 @@
 /*
  * DDR Setup
  */
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
 
@@ -71,7 +69,6 @@
 #define CFG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CFG_SYS_FLASH_BASE)
 
 /* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
 #define CFG_SYS_INIT_RAM_ADDR	0xfdd00000	/* Initial L1 address */
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe03c000
diff --git a/include/configs/alt.h b/include/configs/alt.h
index fe303fda78a0..f27740016927 100644
--- a/include/configs/alt.h
+++ b/include/configs/alt.h
@@ -20,9 +20,6 @@
 #define RCAR_GEN2_SDRAM_SIZE		(1024u * 1024 * 1024)
 #define RCAR_GEN2_UBOOT_SDRAM_SIZE	(512 * 1024 * 1024)
 
-/* FLASH */
-#define CONFIG_SPI_FLASH_QUAD
-
 /* SH Ether */
 #define CONFIG_SH_ETHER_USE_PORT	0
 #define CONFIG_SH_ETHER_PHY_ADDR	0x1
diff --git a/include/configs/ax25-ae350.h b/include/configs/ax25-ae350.h
index 03e04e6e6805..d70f0382300f 100644
--- a/include/configs/ax25-ae350.h
+++ b/include/configs/ax25-ae350.h
@@ -49,9 +49,6 @@
 */
 #define CFG_SYS_FLASH_BANKS_SIZES {0x4000000}
 
-/* max number of sectors on one chip */
-#define CONFIG_FLASH_SECTOR_SIZE	(0x10000*2)
-
 /* environments */
 
 /* SPI FLASH */
diff --git a/include/configs/beaver.h b/include/configs/beaver.h
index 6b5f650811b8..7078c2745c8e 100644
--- a/include/configs/beaver.h
+++ b/include/configs/beaver.h
@@ -20,10 +20,6 @@
 #define CONFIG_TEGRA_ENABLE_UARTA
 #define CFG_SYS_NS16550_COM1		NV_PA_APB_UARTA_BASE
 
-/* SPI */
-#define CONFIG_TEGRA_SLINK_CTRLS       6
-#define CONFIG_SPI_FLASH_SIZE          (4 << 20)
-
 #include "tegra-common-post.h"
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/blanche.h b/include/configs/blanche.h
index fe09997e1784..d4e0f677e67b 100644
--- a/include/configs/blanche.h
+++ b/include/configs/blanche.h
@@ -22,9 +22,7 @@
 #define RCAR_GEN2_UBOOT_SDRAM_SIZE	(512 * 1024 * 1024)
 
 /* FLASH */
-#if !defined(CONFIG_MTD_NOR_FLASH)
-#define CONFIG_SH_QSPI_BASE	0xE6B10000
-#else
+#if defined(CONFIG_MTD_NOR_FLASH)
 #define CFG_SYS_FLASH_BASE		0x00000000
 #define CFG_SYS_FLASH_SIZE		0x04000000	/* 64 MB */
 #define CFG_SYS_FLASH_BANKS_LIST	{ (CFG_SYS_FLASH_BASE) }
diff --git a/include/configs/cardhu.h b/include/configs/cardhu.h
index 35c5a4f12261..5cca1e18348d 100644
--- a/include/configs/cardhu.h
+++ b/include/configs/cardhu.h
@@ -24,10 +24,6 @@
 #define CONFIG_TEGRA_ENABLE_UARTA
 #define CFG_SYS_NS16550_COM1		NV_PA_APB_UARTA_BASE
 
-/* SPI */
-#define CONFIG_TEGRA_SLINK_CTRLS       6
-#define CONFIG_SPI_FLASH_SIZE          (4 << 20)
-
 #include "tegra-common-post.h"
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/cei-tk1-som.h b/include/configs/cei-tk1-som.h
index 55e2d744c4a0..e3519ed75169 100644
--- a/include/configs/cei-tk1-som.h
+++ b/include/configs/cei-tk1-som.h
@@ -22,9 +22,6 @@
 #define CONFIG_TEGRA_ENABLE_UARTD
 #define CFG_SYS_NS16550_COM1		NV_PA_APB_UARTD_BASE
 
-/* SPI */
-#define CONFIG_SPI_FLASH_SIZE		(4 << 20)
-
 #include "tegra-common-post.h"
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/colibri_vf.h b/include/configs/colibri_vf.h
index 8a790400b46d..e8918df69e05 100644
--- a/include/configs/colibri_vf.h
+++ b/include/configs/colibri_vf.h
@@ -14,10 +14,6 @@
 #include <asm/arch/imx-regs.h>
 #include <linux/sizes.h>
 
-/* NAND support */
-
-#define CONFIG_FDTADDR			0x84000000
-
 #define MEM_LAYOUT_ENV_SETTINGS \
 	"bootm_size=0x10000000\0" \
 	"fdt_addr_r=0x82000000\0" \
diff --git a/include/configs/dalmore.h b/include/configs/dalmore.h
index 24cf554649ba..82b2efdfe897 100644
--- a/include/configs/dalmore.h
+++ b/include/configs/dalmore.h
@@ -19,9 +19,6 @@
 
 /* Environment in eMMC, at the end of 2nd "boot sector" */
 
-/* SPI */
-#define CONFIG_SPI_FLASH_SIZE          (4 << 20)
-
 #include "tegra-common-post.h"
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/dns325.h b/include/configs/dns325.h
index 015bc78648f3..1bfb741346a7 100644
--- a/include/configs/dns325.h
+++ b/include/configs/dns325.h
@@ -16,13 +16,6 @@
 
 /* Remove or override few declarations from mv-common.h */
 
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS		{1, 0} /* enable port 0 only */
-#endif
-
 /*
  * Enable GPI0 support
  */
diff --git a/include/configs/dockstar.h b/include/configs/dockstar.h
index 33ae7d654b0b..a6c1e9c6d029 100644
--- a/include/configs/dockstar.h
+++ b/include/configs/dockstar.h
@@ -28,10 +28,4 @@
 	"initrd=/boot/uInitrd\0" \
 	"bootargs_root=ubi.mtd=1 root=ubi0:root rootfstype=ubifs ro\0"
 
-/*
- * Ethernet Driver configuration
- */
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
-#define CONFIG_PHY_BASE_ADR	0
-
 #endif /* _CONFIG_DOCKSTAR_H */
diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h
index b8f518612ee3..f8afcc7826e9 100644
--- a/include/configs/dra7xx_evm.h
+++ b/include/configs/dra7xx_evm.h
@@ -13,7 +13,6 @@
 
 #include <environment/ti/dfu.h>
 
-#define CONFIG_VERY_BIG_RAM
 #define CONFIG_MAX_MEM_MAPPED		0x80000000
 
 #ifndef CONFIG_QSPI_BOOT
diff --git a/include/configs/dreamplug.h b/include/configs/dreamplug.h
index fbd83d629c02..98322a54f631 100644
--- a/include/configs/dreamplug.h
+++ b/include/configs/dreamplug.h
@@ -24,10 +24,4 @@
 	"x_bootargs=console=ttyS0,115200\0"	\
 	"x_bootargs_root=root=/dev/sda2 rootdelay=10\0"
 
-/*
- * Ethernet Driver configuration
- */
-#define CONFIG_MVGBE_PORTS	{1, 1}	/* enable both ports */
-#define CONFIG_PHY_BASE_ADR	0
-
 #endif /* _CONFIG_DREAMPLUG_H */
diff --git a/include/configs/ds109.h b/include/configs/ds109.h
index 8553ea0b95f2..8e7a86e06262 100644
--- a/include/configs/ds109.h
+++ b/include/configs/ds109.h
@@ -35,12 +35,4 @@
 	"ipaddr=192.168.1.5\0"		\
 	"usb0Mode=host\0"
 
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable one port */
-#define CONFIG_PHY_BASE_ADR	8
-#endif /* CONFIG_CMD_NET */
-
 #endif /* _CONFIG_DS109_H */
diff --git a/include/configs/eb_cpu5282.h b/include/configs/eb_cpu5282.h
index 717f49ca29d8..029f13dad36f 100644
--- a/include/configs/eb_cpu5282.h
+++ b/include/configs/eb_cpu5282.h
@@ -144,13 +144,5 @@
 #define CFG_SYS_DDRUA		0x05
 #define CFG_SYS_PJPAR		0xFF
 
-/*-----------------------------------------------------------------------
- * I2C
- */
-
-#ifdef CONFIG_CMD_DATE
-#define CONFIG_I2C_RTC_ADDR		0x68
-#endif
-
 #endif	/* _CONFIG_M5282EVB_H */
 /*---------------------------------------------------------------------*/
diff --git a/include/configs/efi-x86_app.h b/include/configs/efi-x86_app.h
index 6061a6db0a40..17a785140262 100644
--- a/include/configs/efi-x86_app.h
+++ b/include/configs/efi-x86_app.h
@@ -8,8 +8,6 @@
 
 #include <configs/x86-common.h>
 
-#undef CONFIG_TPM_TIS_BASE_ADDRESS
-
 #define CONFIG_STD_DEVICES_SETTINGS	"stdin=serial\0" \
 					"stdout=vidconsole\0" \
 					"stderr=vidconsole\0"
diff --git a/include/configs/embestmx6boards.h b/include/configs/embestmx6boards.h
index 22e0fa5aabfd..1742b1192fb4 100644
--- a/include/configs/embestmx6boards.h
+++ b/include/configs/embestmx6boards.h
@@ -35,11 +35,11 @@
 
 #if defined(CONFIG_ENV_IS_IN_MMC)
 /* RiOTboard */
-#define CONFIG_FDTFILE	"imx6dl-riotboard.dtb"
+#define FDTFILE	"imx6dl-riotboard.dtb"
 #define CFG_SYS_FSL_USDHC_NUM	3
 #elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
 /* MarSBoard */
-#define CONFIG_FDTFILE	"imx6q-marsboard.dtb"
+#define FDTFILE	"imx6q-marsboard.dtb"
 #define CFG_SYS_FSL_USDHC_NUM	2
 #endif
 
@@ -79,7 +79,7 @@
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	CONSOLE_ENV_SETTINGS \
 	MEM_LAYOUT_ENV_SETTINGS \
-	"fdtfile=" CONFIG_FDTFILE "\0" \
+	"fdtfile=" FDTFILE "\0" \
 	"finduuid=part uuid mmc 0:1 uuid\0" \
 	BOOTENV
 
diff --git a/include/configs/ethernut5.h b/include/configs/ethernut5.h
index 52eb0be67611..3fd58d6bd4a7 100644
--- a/include/configs/ethernut5.h
+++ b/include/configs/ethernut5.h
@@ -49,7 +49,6 @@
 
 /* Ethernet */
 #define CONFIG_PHY_ID			0
-#define CONFIG_MACB_SEARCH_PHY
 
 /* MMC */
 #ifdef CONFIG_CMD_MMC
diff --git a/include/configs/exynos5-common.h b/include/configs/exynos5-common.h
index 9b5c329bda18..8e277ce7ff26 100644
--- a/include/configs/exynos5-common.h
+++ b/include/configs/exynos5-common.h
@@ -27,8 +27,6 @@
 /* MMC SPL */
 #define COPY_BL2_FNPTR_ADDR	0x02020030
 
-#define CONFIG_RD_LVL
-
 #define PHYS_SDRAM_1		CFG_SYS_SDRAM_BASE
 #define PHYS_SDRAM_1_SIZE	SDRAM_BANK_SIZE
 #define PHYS_SDRAM_2		(CFG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
diff --git a/include/configs/exynos5420-common.h b/include/configs/exynos5420-common.h
index 7a9307ccc3db..934a4ef9d1f1 100644
--- a/include/configs/exynos5420-common.h
+++ b/include/configs/exynos5420-common.h
@@ -8,8 +8,6 @@
 #ifndef __CONFIG_EXYNOS5420_H
 #define __CONFIG_EXYNOS5420_H
 
-#define CONFIG_VAR_SIZE_SPL
-
 #define CONFIG_IRAM_TOP			0x02074000
 
 #define CONFIG_PHY_IRAM_BASE		0x02020000
diff --git a/include/configs/exynos7420-common.h b/include/configs/exynos7420-common.h
index cff910c1bd5b..e22dd036ccb8 100644
--- a/include/configs/exynos7420-common.h
+++ b/include/configs/exynos7420-common.h
@@ -15,10 +15,6 @@
 
 /* select serial console configuration */
 
-/* IRAM Layout */
-#define CONFIG_IRAM_BASE		0x02100000
-#define CONFIG_IRAM_SIZE		0x58000
-#define CONFIG_IRAM_END			(CONFIG_IRAM_BASE + CONFIG_IRAM_SIZE)
 #define CPU_RELEASE_ADDR		secondary_boot_addr
 
 /* select serial console configuration */
diff --git a/include/configs/goflexhome.h b/include/configs/goflexhome.h
index 66eed9e14f81..1c86dcb1f6dd 100644
--- a/include/configs/goflexhome.h
+++ b/include/configs/goflexhome.h
@@ -36,10 +36,4 @@
 	"kernel=/boot/uImage\0" \
 	"bootargs_root=ubi.mtd=root root=ubi0:root rootfstype=ubifs ro\0"
 
-/*
- * Ethernet Driver configuration
- */
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
-#define CONFIG_PHY_BASE_ADR	0
-
 #endif /* _CONFIG_GOFLEXHOME_H */
diff --git a/include/configs/guruplug.h b/include/configs/guruplug.h
index 4954c5ca0800..d196c4eda535 100644
--- a/include/configs/guruplug.h
+++ b/include/configs/guruplug.h
@@ -30,12 +30,4 @@
 	"fdt=/boot/guruplug-server-plus.dtb\0"				\
 	"bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw\0"
 
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS	{1, 1}	/* enable both ports */
-#define CONFIG_PHY_BASE_ADR	0
-#endif /* CONFIG_CMD_NET */
-
 #endif /* _CONFIG_GURUPLUG_H */
diff --git a/include/configs/ib62x0.h b/include/configs/ib62x0.h
index 05192218d225..76fc4ac8b66c 100644
--- a/include/configs/ib62x0.h
+++ b/include/configs/ib62x0.h
@@ -24,14 +24,6 @@
 	"fdt=/boot/ib62x0.dtb\0"					\
 	"bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw\0"
 
-/*
- * Ethernet driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
-#define CONFIG_PHY_BASE_ADR	0
-#endif /* CONFIG_CMD_NET */
-
 /*
  * SATA driver configuration
  */
diff --git a/include/configs/iconnect.h b/include/configs/iconnect.h
index f2e3608d3a3f..6d2104b3a1cd 100644
--- a/include/configs/iconnect.h
+++ b/include/configs/iconnect.h
@@ -16,14 +16,4 @@
 	"kernel=/boot/uImage\0"			\
 	"bootargs_root=noinitrd ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs\0"
 
-/*
- * Ethernet driver configuration
- *
- * This board has PCIe Wifi card, so allow Ethernet to be disabled
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
-#define CONFIG_PHY_BASE_ADR	11
-#endif /* CONFIG_CMD_NET */
-
 #endif /* _CONFIG_ICONNECT_H */
diff --git a/include/configs/jetson-tk1.h b/include/configs/jetson-tk1.h
index b846889541c7..ea4964b13d67 100644
--- a/include/configs/jetson-tk1.h
+++ b/include/configs/jetson-tk1.h
@@ -18,11 +18,6 @@
 #define CONFIG_TEGRA_ENABLE_UARTD
 #define CFG_SYS_NS16550_COM1		NV_PA_APB_UARTD_BASE
 
-/* Environment in eMMC, at the end of 2nd "boot sector" */
-
-/* SPI */
-#define CONFIG_SPI_FLASH_SIZE		(4 << 20)
-
 #include "tegra-common-post.h"
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/k2e_evm.h b/include/configs/k2e_evm.h
index bbc58be511e4..174a91c83e19 100644
--- a/include/configs/k2e_evm.h
+++ b/include/configs/k2e_evm.h
@@ -39,6 +39,5 @@
 /* Network */
 #define CONFIG_KSNET_NETCP_V1_5
 #define CONFIG_KSNET_CPSW_NUM_PORTS	9
-#define CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
 
 #endif /* __CONFIG_K2E_EVM_H */
diff --git a/include/configs/k2g_evm.h b/include/configs/k2g_evm.h
index bb91751d5d90..dc06d5943e5c 100644
--- a/include/configs/k2g_evm.h
+++ b/include/configs/k2g_evm.h
@@ -53,7 +53,6 @@
 /* Network */
 #define CONFIG_KSNET_NETCP_V1_5
 #define CONFIG_KSNET_CPSW_NUM_PORTS	2
-#define CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
 #define PHY_ANEG_TIMEOUT	10000 /* PHY needs longer aneg time */
 
 #define SPI_MTD_PARTS	KEYSTONE_SPI1_MTD_PARTS
diff --git a/include/configs/k2l_evm.h b/include/configs/k2l_evm.h
index a18158a7eb33..5d629452bae4 100644
--- a/include/configs/k2l_evm.h
+++ b/include/configs/k2l_evm.h
@@ -39,6 +39,5 @@
 /* Network */
 #define CONFIG_KSNET_NETCP_V1_5
 #define CONFIG_KSNET_CPSW_NUM_PORTS	5
-#define CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
 
 #endif /* __CONFIG_K2L_EVM_H */
diff --git a/include/configs/kmcent2.h b/include/configs/kmcent2.h
index 366272d49e86..580d3a0faf01 100644
--- a/include/configs/kmcent2.h
+++ b/include/configs/kmcent2.h
@@ -160,7 +160,6 @@
 /*
  * DDR Setup
  */
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
 
diff --git a/include/configs/kontron_sl28.h b/include/configs/kontron_sl28.h
index 9c3174d0e02c..f7bb97aa0e6c 100644
--- a/include/configs/kontron_sl28.h
+++ b/include/configs/kontron_sl28.h
@@ -18,7 +18,6 @@
 /* DDR */
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x80000000
 #define CFG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
diff --git a/include/configs/lacie_kw.h b/include/configs/lacie_kw.h
index 828f91096344..7a66df548a3b 100644
--- a/include/configs/lacie_kw.h
+++ b/include/configs/lacie_kw.h
@@ -14,13 +14,6 @@
  * Enable platform initialisation via misc_init_r() function
  */
 
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS		{1, 0} /* enable port 0 only */
-#endif
-
 /*
  * Enable GPI0 support
  */
diff --git a/include/configs/legoev3.h b/include/configs/legoev3.h
index abe470fe890b..794c1fcbed06 100644
--- a/include/configs/legoev3.h
+++ b/include/configs/legoev3.h
@@ -48,7 +48,6 @@
  * Linux Information
  */
 #define LINUX_BOOT_PARAM_ADDR	(PHYS_SDRAM_1 + 0x100)
-#define CONFIG_SETUP_INITRD_TAG
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"bootenvfile=uEnv.txt\0" \
 	"fdtfile=da850-lego-ev3.dtb\0" \
diff --git a/include/configs/ls1028a_common.h b/include/configs/ls1028a_common.h
index b190bfe9c8e0..2ccb20192d4f 100644
--- a/include/configs/ls1028a_common.h
+++ b/include/configs/ls1028a_common.h
@@ -12,7 +12,6 @@
 
 /* Link Definitions */
 
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x80000000UL
 #define CFG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
diff --git a/include/configs/ls1043a_common.h b/include/configs/ls1043a_common.h
index e54e903a8a94..d0380b33732d 100644
--- a/include/configs/ls1043a_common.h
+++ b/include/configs/ls1043a_common.h
@@ -31,7 +31,6 @@
 
 /* Link Definitions */
 
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x80000000
 #define CFG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
diff --git a/include/configs/ls1043aqds.h b/include/configs/ls1043aqds.h
index dab57382eddf..1dca7f0aa6b9 100644
--- a/include/configs/ls1043aqds.h
+++ b/include/configs/ls1043aqds.h
@@ -107,7 +107,6 @@
 #define CFG_SYS_NAND_FTIM3           0x0
 
 #define CFG_SYS_NAND_BASE_LIST	{ CFG_SYS_NAND_BASE }
-#define CONFIG_MTD_NAND_VERIFY_WRITE
 #endif
 
 #ifdef CONFIG_NAND_BOOT
diff --git a/include/configs/ls1043ardb.h b/include/configs/ls1043ardb.h
index 12c4853ea963..043904197f01 100644
--- a/include/configs/ls1043ardb.h
+++ b/include/configs/ls1043ardb.h
@@ -82,7 +82,6 @@
 #define CFG_SYS_NAND_FTIM3		0x0
 
 #define CFG_SYS_NAND_BASE_LIST	{ CFG_SYS_NAND_BASE }
-#define CONFIG_MTD_NAND_VERIFY_WRITE
 
 #ifdef CONFIG_NAND_BOOT
 #define CFG_SYS_NAND_U_BOOT_SIZE	(1024 << 10)
diff --git a/include/configs/ls1046a_common.h b/include/configs/ls1046a_common.h
index 4ed5481c3e74..250891e9e301 100644
--- a/include/configs/ls1046a_common.h
+++ b/include/configs/ls1046a_common.h
@@ -31,7 +31,6 @@
 
 /* Link Definitions */
 
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x80000000
 #define CFG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
diff --git a/include/configs/ls1046afrwy.h b/include/configs/ls1046afrwy.h
index 1759d25f3a39..5e03a962d10e 100644
--- a/include/configs/ls1046afrwy.h
+++ b/include/configs/ls1046afrwy.h
@@ -45,7 +45,6 @@
 #define CFG_SYS_NAND_FTIM3		0x0
 
 #define CFG_SYS_NAND_BASE_LIST	{ CFG_SYS_NAND_BASE }
-#define CONFIG_MTD_NAND_VERIFY_WRITE
 
 /* IFC Timing Params */
 #define CFG_SYS_CSPR0_EXT		CFG_SYS_NAND_CSPR_EXT
diff --git a/include/configs/ls1046aqds.h b/include/configs/ls1046aqds.h
index e9b8ad0c0b7f..c4e5f4928d22 100644
--- a/include/configs/ls1046aqds.h
+++ b/include/configs/ls1046aqds.h
@@ -123,7 +123,6 @@
 #define CFG_SYS_NAND_FTIM3           0x0
 
 #define CFG_SYS_NAND_BASE_LIST	{ CFG_SYS_NAND_BASE }
-#define CONFIG_MTD_NAND_VERIFY_WRITE
 #endif
 
 #ifdef CONFIG_NAND_BOOT
diff --git a/include/configs/ls1046ardb.h b/include/configs/ls1046ardb.h
index f3904e7b3f7b..ad766b034b16 100644
--- a/include/configs/ls1046ardb.h
+++ b/include/configs/ls1046ardb.h
@@ -50,7 +50,6 @@
 #define CFG_SYS_NAND_FTIM3		0x0
 
 #define CFG_SYS_NAND_BASE_LIST	{ CFG_SYS_NAND_BASE }
-#define CONFIG_MTD_NAND_VERIFY_WRITE
 
 /*
  * CPLD
diff --git a/include/configs/ls1088a_common.h b/include/configs/ls1088a_common.h
index 57429d4bbe32..bcba8d81c04c 100644
--- a/include/configs/ls1088a_common.h
+++ b/include/configs/ls1088a_common.h
@@ -29,7 +29,6 @@
 /* Link Definitions */
 #define CFG_SYS_FSL_QSPI_BASE	0x20000000
 
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x80000000UL
 #define CFG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
diff --git a/include/configs/ls1088aqds.h b/include/configs/ls1088aqds.h
index dc9cded49fdf..49ad14692623 100644
--- a/include/configs/ls1088aqds.h
+++ b/include/configs/ls1088aqds.h
@@ -97,7 +97,6 @@
 #define CFG_SYS_NAND_FTIM3		0x0
 
 #define CFG_SYS_NAND_BASE_LIST	{ CFG_SYS_NAND_BASE }
-#define CONFIG_MTD_NAND_VERIFY_WRITE
 
 #define CFG_SYS_I2C_FPGA_ADDR	0x66
 #define QIXIS_LBMAP_SWITCH		6
diff --git a/include/configs/ls1088ardb.h b/include/configs/ls1088ardb.h
index e2444cd8eb4b..9033f6e937c2 100644
--- a/include/configs/ls1088ardb.h
+++ b/include/configs/ls1088ardb.h
@@ -81,7 +81,6 @@
 #define CFG_SYS_NAND_FTIM3		0x0
 
 #define CFG_SYS_NAND_BASE_LIST	{ CFG_SYS_NAND_BASE }
-#define CONFIG_MTD_NAND_VERIFY_WRITE
 
 #define CFG_SYS_I2C_FPGA_ADDR	0x66
 #define QIXIS_BRDCFG4_OFFSET            0x54
diff --git a/include/configs/ls2080a_common.h b/include/configs/ls2080a_common.h
index e82456fd8148..bd78bdb793a6 100644
--- a/include/configs/ls2080a_common.h
+++ b/include/configs/ls2080a_common.h
@@ -16,7 +16,6 @@
 
 /* Link Definitions */
 
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x80000000UL
 #define CFG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
diff --git a/include/configs/ls2080aqds.h b/include/configs/ls2080aqds.h
index 4e6d40afbf1c..7d3e8912c3b0 100644
--- a/include/configs/ls2080aqds.h
+++ b/include/configs/ls2080aqds.h
@@ -98,7 +98,6 @@
 #define CFG_SYS_NAND_FTIM3		0x0
 
 #define CFG_SYS_NAND_BASE_LIST	{ CFG_SYS_NAND_BASE }
-#define CONFIG_MTD_NAND_VERIFY_WRITE
 
 #define QIXIS_LBMAP_SWITCH		0x06
 #define QIXIS_LBMAP_MASK		0x0f
diff --git a/include/configs/ls2080ardb.h b/include/configs/ls2080ardb.h
index 8f36958f7103..4573906115eb 100644
--- a/include/configs/ls2080ardb.h
+++ b/include/configs/ls2080ardb.h
@@ -95,7 +95,6 @@
 #define CFG_SYS_NAND_FTIM3		0x0
 
 #define CFG_SYS_NAND_BASE_LIST	{ CFG_SYS_NAND_BASE }
-#define CONFIG_MTD_NAND_VERIFY_WRITE
 
 #define QIXIS_LBMAP_SWITCH		0x06
 #define QIXIS_LBMAP_MASK		0x0f
diff --git a/include/configs/lx2160a_common.h b/include/configs/lx2160a_common.h
index a469c83fa4eb..3347920f03f7 100644
--- a/include/configs/lx2160a_common.h
+++ b/include/configs/lx2160a_common.h
@@ -13,7 +13,6 @@
 #define CFG_SYS_FLASH_BASE		0x20000000
 
 /* DDR */
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE		0x80000000UL
 #define CFG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
 #define CFG_SYS_DDR_BLOCK2_BASE		0x2080000000ULL
diff --git a/include/configs/malta.h b/include/configs/malta.h
index 65f4b05649b2..8ba04b4e6c31 100644
--- a/include/configs/malta.h
+++ b/include/configs/malta.h
@@ -11,8 +11,6 @@
  */
 #define CONFIG_MALTA
 
-#define CONFIG_MEMSIZE_IN_BYTES
-
 /*
  * CPU Configuration
  */
diff --git a/include/configs/mt7621.h b/include/configs/mt7621.h
index 7c8c67f44697..b6e680bcc78e 100644
--- a/include/configs/mt7621.h
+++ b/include/configs/mt7621.h
@@ -10,7 +10,6 @@
 
 #define CFG_SYS_SDRAM_BASE		0x80000000
 
-#define CONFIG_VERY_BIG_RAM
 #define CONFIG_MAX_MEM_MAPPED		0x1c000000
 
 #define CFG_SYS_INIT_SP_OFFSET	0x800000
diff --git a/include/configs/mt7629.h b/include/configs/mt7629.h
index 99b09ad41e74..f6ab486fa292 100644
--- a/include/configs/mt7629.h
+++ b/include/configs/mt7629.h
@@ -15,10 +15,7 @@
 
 /* Environment */
 
-/* Defines for SPL */
-
-#define CONFIG_SPI_ADDR			0x30000000
-#define CFG_SYS_UBOOT_BASE		(CONFIG_SPI_ADDR + CONFIG_SPL_PAD_TO)
+#define CFG_SYS_UBOOT_BASE		(0x30000000 + CONFIG_SPL_PAD_TO)
 
 /* SPL -> Uboot */
 
diff --git a/include/configs/mxs.h b/include/configs/mxs.h
index 30f27e7f0c19..32e0e06617e5 100644
--- a/include/configs/mxs.h
+++ b/include/configs/mxs.h
@@ -86,9 +86,4 @@
 #define CFG_SYS_NAND_BASE		0x60000000
 #endif
 
-/* SPI */
-#ifdef CONFIG_CMD_SPI
-#define CONFIG_SPI_HALF_DUPLEX
-#endif
-
 #endif	/* __CONFIGS_MXS_H__ */
diff --git a/include/configs/nas220.h b/include/configs/nas220.h
index 1b7eb3433483..85691ca94f08 100644
--- a/include/configs/nas220.h
+++ b/include/configs/nas220.h
@@ -39,16 +39,4 @@
 	"bootargs=console=ttyS0,115200\0" \
 	"autostart=no\0"
 
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS {1, 0}	/* enable port 0 only */
-#define CONFIG_PHY_BASE_ADR 8
-#endif /* CONFIG_CMD_NET */
-
-/*
- * EFI partition
- */
-
 #endif /* _CONFIG_NAS220_H */
diff --git a/include/configs/nsa310s.h b/include/configs/nsa310s.h
index 62f07011809c..e2ad77072cd5 100644
--- a/include/configs/nsa310s.h
+++ b/include/configs/nsa310s.h
@@ -46,8 +46,4 @@
 
 #endif /* CONFIG_SPL_BUILD */
 
-/* Ethernet driver configuration */
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
-#define CONFIG_PHY_BASE_ADR	1
-
 #endif /* _CONFIG_NSA310S_H */
diff --git a/include/configs/nyan-big.h b/include/configs/nyan-big.h
index baa452156ecd..21002f99dc88 100644
--- a/include/configs/nyan-big.h
+++ b/include/configs/nyan-big.h
@@ -18,9 +18,6 @@
 #define CONFIG_TEGRA_ENABLE_UARTA
 #define CFG_SYS_NS16550_COM1		NV_PA_APB_UARTA_BASE
 
-/* SPI */
-#define CONFIG_SPI_FLASH_SIZE          (4 << 20)
-
 #include "tegra-common-post.h"
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/openrd.h b/include/configs/openrd.h
index 006f06e6af5c..2cec20ca4259 100644
--- a/include/configs/openrd.h
+++ b/include/configs/openrd.h
@@ -33,26 +33,4 @@
 	"x_bootcmd_usb=usb start\0"					\
 	"x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0"
 
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-# ifdef CONFIG_BOARD_IS_OPENRD_BASE
-#  define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
-# else
-#  define CONFIG_MVGBE_PORTS	{1, 1}	/* enable both ports */
-# endif
-# ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE
-#  define CONFIG_PHY_BASE_ADR	0x0
-#  define PHY_NO		"88E1121"
-# else
-#  define CONFIG_PHY_BASE_ADR	0x8
-#  define PHY_NO		"88E1116"
-# endif
-#endif /* CONFIG_CMD_NET */
-
-/*
- * SATA Driver configuration
- */
-
 #endif /* _CONFIG_OPENRD_BASE_H */
diff --git a/include/configs/origen.h b/include/configs/origen.h
index 6633d541a31b..a608df44e80e 100644
--- a/include/configs/origen.h
+++ b/include/configs/origen.h
@@ -38,10 +38,4 @@
         "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
                 "source ${loadaddr}\0"
 
-/* MIU (Memory Interleaving Unit) */
-#define CONFIG_MIU_2BIT_21_7_INTERLEAVED
-
-#define RESERVE_BLOCK_SIZE		(512)
-#define BL1_SIZE			(16 << 10) /*16 K reserved for BL1*/
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/p2371-0000.h b/include/configs/p2371-0000.h
index ecd0405d297b..653b4c583ad2 100644
--- a/include/configs/p2371-0000.h
+++ b/include/configs/p2371-0000.h
@@ -19,9 +19,6 @@
 
 /* Environment in eMMC, at the end of 2nd "boot sector" */
 
-/* SPI */
-#define CONFIG_SPI_FLASH_SIZE		(4 << 20)
-
 #include "tegra-common-post.h"
 
 #endif /* _P2371_0000_H */
diff --git a/include/configs/p2371-2180.h b/include/configs/p2371-2180.h
index 7f942888e74d..2913d5304be7 100644
--- a/include/configs/p2371-2180.h
+++ b/include/configs/p2371-2180.h
@@ -19,9 +19,6 @@
 
 /* Environment in eMMC, at the end of 2nd "boot sector" */
 
-/* SPI */
-#define CONFIG_SPI_FLASH_SIZE		(4 << 20)
-
 #include "tegra-common-post.h"
 
 #endif /* _P2371_2180_H */
diff --git a/include/configs/p2571.h b/include/configs/p2571.h
index 50cddb4a4acb..e78e3c4d6b09 100644
--- a/include/configs/p2571.h
+++ b/include/configs/p2571.h
@@ -19,9 +19,6 @@
 
 /* Environment in eMMC, at the end of 2nd "boot sector" */
 
-/* SPI */
-#define CONFIG_SPI_FLASH_SIZE		(4 << 20)
-
 #include "tegra-common-post.h"
 
 #endif /* _P2571_H */
diff --git a/include/configs/p3450-0000.h b/include/configs/p3450-0000.h
index ec1a8634e718..bab02dc2d6ed 100644
--- a/include/configs/p3450-0000.h
+++ b/include/configs/p3450-0000.h
@@ -23,9 +23,6 @@
 	func(PXE, pxe, na) \
 	func(DHCP, dhcp, na)
 
-/* Environment at end of QSPI, in the VER partition */
-#define CONFIG_SPI_FLASH_SIZE		(4 << 20)
-
 #define BOARD_EXTRA_ENV_SETTINGS \
 	"preboot=if test -e mmc 1:1 /u-boot-preboot.scr; then " \
 		"load mmc 1:1 ${scriptaddr} /u-boot-preboot.scr; " \
diff --git a/include/configs/pm9263.h b/include/configs/pm9263.h
index 9fd897958a4f..fa08744b6feb 100644
--- a/include/configs/pm9263.h
+++ b/include/configs/pm9263.h
@@ -159,11 +159,6 @@
 /* PSRAM */
 #define	PHYS_PSRAM			0x70000000
 #define	PHYS_PSRAM_SIZE			0x00400000	/* 4MB */
-/* Slave EBI1, PSRAM connected */
-#define CONFIG_PSRAM_SCFG		(AT91_MATRIX_SCFG_ARBT_FIXED_PRIORITY	| \
-					 AT91_MATRIX_SCFG_FIXED_DEFMSTR(5)	| \
-					 AT91_MATRIX_SCFG_DEFMSTR_TYPE_FIXED	| \
-					 AT91_MATRIX_SCFG_SLOT_CYCLE(255))
 
 /* USB */
 #define CFG_SYS_USB_OHCI_REGS_BASE		0x00a00000	/* AT91SAM9263_UHP_BASE */
diff --git a/include/configs/pogo_e02.h b/include/configs/pogo_e02.h
index 085732214e50..fc9f113dee66 100644
--- a/include/configs/pogo_e02.h
+++ b/include/configs/pogo_e02.h
@@ -23,10 +23,4 @@
 	"bootcmd_usb=usb start; ext2load usb 0:1 0x00800000 /uImage; " \
 	"ext2load usb 0:1 0x01100000 /uInitrd\0"
 
-/*
- * Ethernet Driver configuration
- */
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
-#define CONFIG_PHY_BASE_ADR	0
-
 #endif /* _CONFIG_POGO_E02_H */
diff --git a/include/configs/pogo_v4.h b/include/configs/pogo_v4.h
index b5ce2dd13d08..239d33d8e9de 100644
--- a/include/configs/pogo_v4.h
+++ b/include/configs/pogo_v4.h
@@ -69,10 +69,4 @@
 	BOOTENV
 #endif /* CONFIG_SPL_BUILD */
 
-/*
- * Ethernet Driver configuration
- */
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
-#define CONFIG_PHY_BASE_ADR	0
-
 #endif /* _CONFIG_POGO_V4_H */
diff --git a/include/configs/porter.h b/include/configs/porter.h
index 88fa65e0ffc1..e0f77f358b95 100644
--- a/include/configs/porter.h
+++ b/include/configs/porter.h
@@ -21,9 +21,6 @@
 #define RCAR_GEN2_SDRAM_SIZE		(2048u * 1024 * 1024)
 #define RCAR_GEN2_UBOOT_SDRAM_SIZE	(1024u * 1024 * 1024)
 
-/* FLASH */
-#define CONFIG_SPI_FLASH_QUAD
-
 /* SH Ether */
 #define CONFIG_SH_ETHER_USE_PORT	0
 #define CONFIG_SH_ETHER_PHY_ADDR	0x1
diff --git a/include/configs/qemu-ppce500.h b/include/configs/qemu-ppce500.h
index d05618995861..20be4af4628f 100644
--- a/include/configs/qemu-ppce500.h
+++ b/include/configs/qemu-ppce500.h
@@ -29,7 +29,6 @@ extern unsigned long long get_phys_ccsrbar_addr_early(void);
 /*
  * DDR Setup
  */
-#define CONFIG_VERY_BIG_RAM
 #define CFG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
 
diff --git a/include/configs/rcar-gen3-common.h b/include/configs/rcar-gen3-common.h
index e9cbd2538240..86012adfb36f 100644
--- a/include/configs/rcar-gen3-common.h
+++ b/include/configs/rcar-gen3-common.h
@@ -28,7 +28,6 @@
 #define DRAM_RSV_SIZE			0x08000000
 #define CFG_SYS_SDRAM_BASE		(0x40000000 + DRAM_RSV_SIZE)
 #define CFG_SYS_SDRAM_SIZE		(0x80000000u - DRAM_RSV_SIZE)
-#define CONFIG_VERY_BIG_RAM
 #define CONFIG_MAX_MEM_MAPPED		(0x80000000u - DRAM_RSV_SIZE)
 
 /* ENV setting */
diff --git a/include/configs/rk3399_common.h b/include/configs/rk3399_common.h
index 78f624d31ca2..67e0c20dca29 100644
--- a/include/configs/rk3399_common.h
+++ b/include/configs/rk3399_common.h
@@ -10,16 +10,6 @@
 
 #define CONFIG_IRAM_BASE		0xff8c0000
 
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_TPL_BOOTROM_SUPPORT)
-#else
-/*  BSS setup */
-#endif
-
-/* MMC/SD IP block */
-#define CONFIG_ROCKCHIP_SDHCI_MAX_FREQ	200000000
-
-/* RAW SD card / eMMC locations. */
-
 /* FAT sd card locations. */
 #define CFG_SYS_SDRAM_BASE		0
 #define SDRAM_MAX_SIZE			0xf8000000
diff --git a/include/configs/sheevaplug.h b/include/configs/sheevaplug.h
index 19701ccce22e..d7923967a721 100644
--- a/include/configs/sheevaplug.h
+++ b/include/configs/sheevaplug.h
@@ -21,10 +21,4 @@
 	"x_bootcmd_usb=usb start\0" \
 	"x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0"
 
-/*
- * Ethernet Driver configuration
- */
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
-#define CONFIG_PHY_BASE_ADR	0
-
 #endif /* _CONFIG_SHEEVAPLUG_H */
diff --git a/include/configs/silk.h b/include/configs/silk.h
index 58613effaf47..6d605edf7886 100644
--- a/include/configs/silk.h
+++ b/include/configs/silk.h
@@ -21,9 +21,6 @@
 #define RCAR_GEN2_SDRAM_SIZE		(1024u * 1024 * 1024)
 #define RCAR_GEN2_UBOOT_SDRAM_SIZE	(512 * 1024 * 1024)
 
-/* FLASH */
-#define CONFIG_SPI_FLASH_QUAD
-
 /* SH Ether */
 #define CONFIG_SH_ETHER_USE_PORT	0
 #define CONFIG_SH_ETHER_PHY_ADDR	0x1
diff --git a/include/configs/smdk5420.h b/include/configs/smdk5420.h
index 0392530c0adf..0cb70762d925 100644
--- a/include/configs/smdk5420.h
+++ b/include/configs/smdk5420.h
@@ -12,8 +12,6 @@
 #include <configs/exynos5-dt-common.h>
 #include <configs/exynos5-common.h>
 
-#define CONFIG_SMDK5420			/* which is in a SMDK5420 */
-
 #define CFG_SYS_SDRAM_BASE	0x20000000
 
 /* DRAM Memory Banks */
diff --git a/include/configs/smdkv310.h b/include/configs/smdkv310.h
index 601c16ea4538..38de1fa9849f 100644
--- a/include/configs/smdkv310.h
+++ b/include/configs/smdkv310.h
@@ -34,9 +34,6 @@
 
 /* FLASH and environment organization */
 
-#define RESERVE_BLOCK_SIZE		(512)
-#define BL1_SIZE			(16 << 10) /*16 K reserved for BL1*/
-
 /* Ethernet Controllor Driver */
 #ifdef CONFIG_CMD_NET
 #define CONFIG_ENV_SROM_BANK		1
diff --git a/include/configs/socfpga_sr1500.h b/include/configs/socfpga_sr1500.h
index 432144cb40ce..caff0cf25234 100644
--- a/include/configs/socfpga_sr1500.h
+++ b/include/configs/socfpga_sr1500.h
@@ -11,15 +11,9 @@
 #define PHYS_SDRAM_1_SIZE		0x40000000	/* 1GiB on SR1500 */
 
 /* Ethernet on SoC (EMAC) */
-#define CONFIG_PHY_INTERFACE_MODE	PHY_INTERFACE_MODE_RGMII
 /* The PHY is autodetected, so no MII PHY address is needed here */
 #define PHY_ANEG_TIMEOUT	8000
 
-/* Enable SPI NOR flash reset, needed for SPI booting */
-#define CONFIG_SPI_N25Q256A_RESET
-
-/* Environment setting for SPI flash */
-
 /* The rest of the configuration is shared */
 #include <configs/socfpga_common.h>
 
diff --git a/include/configs/socrates.h b/include/configs/socrates.h
index 2a076716023f..11d840223312 100644
--- a/include/configs/socrates.h
+++ b/include/configs/socrates.h
@@ -16,9 +16,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-/* High Level Configuration Options */
-#define CONFIG_SOCRATES		1
-
 /*
  * Only possible on E500 Version 2 or newer cores.
  */
@@ -55,7 +52,6 @@
 
 #define CFG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE
-#define CONFIG_VERY_BIG_RAM
 
 /* I2C addresses of SPD EEPROMs */
 #define SPD_EEPROM_ADDRESS	0x50	/* CTLR 0 DIMM 0 */
diff --git a/include/configs/stout.h b/include/configs/stout.h
index f49e88cb17cb..977c0adc5f02 100644
--- a/include/configs/stout.h
+++ b/include/configs/stout.h
@@ -25,9 +25,6 @@
 /* SCIF */
 #define CONFIG_SCIF_A
 
-/* SPI */
-#define CONFIG_SPI_FLASH_QUAD
-
 /* SH Ether */
 #define CONFIG_SH_ETHER_USE_PORT	0
 #define CONFIG_SH_ETHER_PHY_ADDR	0x1
diff --git a/include/configs/synquacer.h b/include/configs/synquacer.h
index 699268900109..a2b6a1f57d7c 100644
--- a/include/configs/synquacer.h
+++ b/include/configs/synquacer.h
@@ -14,7 +14,6 @@
 #define CFG_SYS_SDRAM_BASE		(0x80000000)	/* Start address of DDR3 */
 #define PHYS_SDRAM_SIZE			(0x7c000000)	/* Default size (2GB - Secure memory) */
 
-#define CONFIG_VERY_BIG_RAM				/* SynQuacer supports up to 64GB */
 #define CONFIG_MAX_MEM_MAPPED		PHYS_SDRAM_SIZE
 
 #define SQ_DRAMINFO_BASE		(0x2e00ffc0)	/* DRAM info from TF-A */
diff --git a/include/configs/tec-ng.h b/include/configs/tec-ng.h
index 098796637010..c98322cf0845 100644
--- a/include/configs/tec-ng.h
+++ b/include/configs/tec-ng.h
@@ -16,12 +16,6 @@
 #define CONFIG_TEGRA_ENABLE_UARTD
 #define CFG_SYS_NS16550_COM1		NV_PA_APB_UARTD_BASE
 
-/* Environment in eMMC, at the end of 2nd "boot sector" */
-
-/* SPI */
-#define CONFIG_TEGRA_SLINK_CTRLS       6
-#define CONFIG_SPI_FLASH_SIZE          (4 << 20)
-
 #include "tegra-common-post.h"
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/venice2.h b/include/configs/venice2.h
index b2dc04a975ad..a4eb4bf4aaf3 100644
--- a/include/configs/venice2.h
+++ b/include/configs/venice2.h
@@ -20,9 +20,6 @@
 
 /* Environment in eMMC, at the end of 2nd "boot sector" */
 
-/* SPI */
-#define CONFIG_SPI_FLASH_SIZE          (4 << 20)
-
 #include "tegra-common-post.h"
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/vinco.h b/include/configs/vinco.h
index 9f72bdde8167..1c1789ac3fb8 100644
--- a/include/configs/vinco.h
+++ b/include/configs/vinco.h
@@ -39,9 +39,6 @@
 
 /* USB device */
 
-/* Ethernet Hardware */
-#define CONFIG_MACB_SEARCH_PHY
-
 #ifdef CONFIG_SPI_BOOT
 /* bootstrap + u-boot + env + linux in serial flash */
 /* Use our own mapping for the VInCo platform */
diff --git a/include/configs/x86-common.h b/include/configs/x86-common.h
index 9bf2462010de..d71108dd3186 100644
--- a/include/configs/x86-common.h
+++ b/include/configs/x86-common.h
@@ -10,22 +10,6 @@
 #ifndef __CONFIG_X86_COMMON_H
 #define __CONFIG_X86_COMMON_H
 
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-/* Generic TPM interfaced through LPC bus */
-#define CONFIG_TPM_TIS_BASE_ADDRESS        0xfed40000
-
-/*-----------------------------------------------------------------------
- * Serial Configuration
- */
-
-/*
- * Miscellaneous configurable options
- */
-
 /*-----------------------------------------------------------------------
  * CPU Features
  */
diff --git a/include/configs/xpress.h b/include/configs/xpress.h
index 3e604894ad48..9f1f2d90dbe1 100644
--- a/include/configs/xpress.h
+++ b/include/configs/xpress.h
@@ -34,9 +34,6 @@
 #define CONFIG_FEC_ENET_DEV		0
 #define CONFIG_FEC_MXC_PHYADDR          0x0
 
-#define CONFIG_UBOOT_SECTOR_START	0x2
-#define CONFIG_UBOOT_SECTOR_COUNT	0x3fe
-
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"script=boot.scr\0" \
 	"image=zImage\0" \
@@ -75,8 +72,8 @@
 			"bootz; " \
 		"fi;\0" \
 	"uboot=ccv/u-boot.imx\0"					\
-	"uboot_start="__stringify(CONFIG_UBOOT_SECTOR_START)"\0"	\
-	"uboot_size="__stringify(CONFIG_UBOOT_SECTOR_COUNT)"\0"		\
+	"uboot_start=0x2\0"						\
+	"uboot_size=0x3fe\0"						\
 	"update_uboot=if tftp ${uboot}; then "				\
 		"if itest ${filesize} > 0; then "			\
 			"mmc dev 0 1;"					\
-- 
2.25.1



More information about the U-Boot mailing list