[PATCH 043/149] global: Migrate CONFIG_I2C_MULTI_BUS to CFG

[Tom Rini]

Perform a simple rename of CONFIG_I2C_MULTI_BUS to CFG_I2C_MULTI_BUS

Signed-off-by: Tom Rini <trini at konsulko.com>
---
 README                         | 2 +-
 include/configs/omap3_beagle.h | 2 +-
 include/configs/sniper.h       | 2 +-
 include/configs/tqma6.h        | 2 +-
 include/i2c.h                  | 2 +-
 5 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/README b/README
index 84086764d810..05618352fa93 100644
--- a/README
+++ b/README
@@ -955,7 +955,7 @@ The following options need to be configured:
 		You should define these to the GPIO value as given directly to
 		the generic GPIO functions.
 
-		CONFIG_I2C_MULTI_BUS
+		CFG_I2C_MULTI_BUS
 
 		This option allows the use of multiple I2C buses, each of which
 		must have a controller.	 At any point in time, only one bus is
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index efeb7bf10078..af7cb3513f8f 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -29,7 +29,7 @@
 #endif /* CONFIG_MTD_RAW_NAND */
 
 /* Enable Multi Bus support for I2C */
-#define CONFIG_I2C_MULTI_BUS
+#define CFG_I2C_MULTI_BUS
 
 /* DSS Support */
 
diff --git a/include/configs/sniper.h b/include/configs/sniper.h
index eaee8dd37396..45a3102aeeef 100644
--- a/include/configs/sniper.h
+++ b/include/configs/sniper.h
@@ -38,7 +38,7 @@
  * I2C
  */
 
-#define CONFIG_I2C_MULTI_BUS
+#define CFG_I2C_MULTI_BUS
 
 /*
  * Input
diff --git a/include/configs/tqma6.h b/include/configs/tqma6.h
index 14d7730f67bf..cb5f7fc25af9 100644
--- a/include/configs/tqma6.h
+++ b/include/configs/tqma6.h
@@ -28,7 +28,7 @@
 #define TQMA6_SPI_FLASH_SECTOR_SIZE	SZ_64K
 
 /* I2C Configs */
-#define CONFIG_I2C_MULTI_BUS
+#define CFG_I2C_MULTI_BUS
 
 #if !defined(CONFIG_DM_PMIC)
 #define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
diff --git a/include/i2c.h b/include/i2c.h
index 51390f8fd84f..3811b26c08e0 100644
--- a/include/i2c.h
+++ b/include/i2c.h
@@ -930,7 +930,7 @@ unsigned int i2c_get_bus_speed(void);
  * only for backwardcompatibility, should go away if we switched
  * completely to new multibus support.
  */
-#if CONFIG_IS_ENABLED(SYS_I2C_LEGACY) || defined(CONFIG_I2C_MULTI_BUS)
+#if CONFIG_IS_ENABLED(SYS_I2C_LEGACY) || defined(CFG_I2C_MULTI_BUS)
 # if !defined(CFG_SYS_MAX_I2C_BUS)
 #  define CFG_SYS_MAX_I2C_BUS		2
 # endif
-- 
2.25.1