[PATCH 3/3] rockchip: Add initial support for the PINE64 Pinephone Pro
Kever Yang
kever.yang at rock-chips.com
Sun Dec 18 10:40:43 CET 2022
On 2022/10/25 15:52, Peter Robinson wrote:
> The Pinephone Pro is another device by PINE64. It's closely related
> to the Pinebook Pro of which this initial support is derived from.
>
> Specification:
> - A variant of the Rockchip RK3399
> - A 6 inch 720*1440 DSI display
> - Front and rear cameras
> - Type-C interface with alt mode display (DP 1.2) and PD charging
> - 4GB LPDDR4 RAM
> - 128GB eMMC
> - mSD card slot
> - An AP6255 module for 802.11ac WiFi and Bluetooth 5
> - Quectel EG25-G 4G/LTE modem
>
> Signed-off-by: Peter Robinson <pbrobinson at gmail.com>
Reviewed-by: Kever Yang <kever.yang at rock-chips.com>
Thanks,
- Kever
> ---
> arch/arm/dts/rk3399-pinephone-pro-u-boot.dtsi | 39 +++++++
> arch/arm/mach-rockchip/rk3399/Kconfig | 8 ++
> board/pine64/pinephone-pro-rk3399/Kconfig | 15 +++
> board/pine64/pinephone-pro-rk3399/MAINTAINERS | 8 ++
> board/pine64/pinephone-pro-rk3399/Makefile | 1 +
> .../pinephone-pro-rk3399.c | 76 +++++++++++++
> configs/pinephone-pro-rk3399_defconfig | 104 ++++++++++++++++++
> include/configs/pinephone-pro-rk3399.h | 19 ++++
> 8 files changed, 270 insertions(+)
> create mode 100644 arch/arm/dts/rk3399-pinephone-pro-u-boot.dtsi
> create mode 100644 board/pine64/pinephone-pro-rk3399/Kconfig
> create mode 100644 board/pine64/pinephone-pro-rk3399/MAINTAINERS
> create mode 100644 board/pine64/pinephone-pro-rk3399/Makefile
> create mode 100644 board/pine64/pinephone-pro-rk3399/pinephone-pro-rk3399.c
> create mode 100644 configs/pinephone-pro-rk3399_defconfig
> create mode 100644 include/configs/pinephone-pro-rk3399.h
>
> diff --git a/arch/arm/dts/rk3399-pinephone-pro-u-boot.dtsi b/arch/arm/dts/rk3399-pinephone-pro-u-boot.dtsi
> new file mode 100644
> index 00000000000..c9f1f4af635
> --- /dev/null
> +++ b/arch/arm/dts/rk3399-pinephone-pro-u-boot.dtsi
> @@ -0,0 +1,39 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2022 Peter Robinson <pbrobinson at gmail.com>
> + */
> +
> +#include "rk3399-u-boot.dtsi"
> +#include "rk3399-sdram-lpddr4-100.dtsi"
> +
> +/ {
> + chosen {
> + u-boot,spl-boot-order = "same-as-spl", &sdhci, &sdmmc;
> + };
> +
> + config {
> + u-boot,spl-payload-offset = <0x60000>; /* @ 384KB */
> + };
> +};
> +
> +&i2c0 {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&rk818 {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&rng {
> + status = "okay";
> +};
> +
> +&sdhci {
> + max-frequency = <25000000>;
> + u-boot,dm-pre-reloc;
> +};
> +
> +&sdmmc {
> + max-frequency = <20000000>;
> + u-boot,dm-pre-reloc;
> +};
> diff --git a/arch/arm/mach-rockchip/rk3399/Kconfig b/arch/arm/mach-rockchip/rk3399/Kconfig
> index b48feeb3466..d01063ac98b 100644
> --- a/arch/arm/mach-rockchip/rk3399/Kconfig
> +++ b/arch/arm/mach-rockchip/rk3399/Kconfig
> @@ -39,6 +39,13 @@ config TARGET_PINEBOOK_PRO_RK3399
> with 4Gb RAM, onboard eMMC, USB-C, a USB3 and USB2 port,
> 1920*1080 screen and all the usual laptop features.
>
> +config TARGET_PINEPHONE_PRO_RK3399
> + bool "PinePhone Pro"
> + help
> + PinePhone Pro is a phone based on a variant of the Rockchip
> + rk3399 SoC with 4Gb RAM, onboard eMMC, USB-C, headphone jack,
> + 720x1440 screen and a Quectel 4G/LTE modem.
> +
> config TARGET_PUMA_RK3399
> bool "Theobroma Systems RK3399-Q7 (Puma)"
> help
> @@ -165,6 +172,7 @@ endif # BOOTCOUNT_LIMIT
> source "board/firefly/roc-pc-rk3399/Kconfig"
> source "board/google/gru/Kconfig"
> source "board/pine64/pinebook-pro-rk3399/Kconfig"
> +source "board/pine64/pinephone-pro-rk3399/Kconfig"
> source "board/pine64/rockpro64_rk3399/Kconfig"
> source "board/rockchip/evb_rk3399/Kconfig"
> source "board/theobroma-systems/puma_rk3399/Kconfig"
> diff --git a/board/pine64/pinephone-pro-rk3399/Kconfig b/board/pine64/pinephone-pro-rk3399/Kconfig
> new file mode 100644
> index 00000000000..13d6465ae6e
> --- /dev/null
> +++ b/board/pine64/pinephone-pro-rk3399/Kconfig
> @@ -0,0 +1,15 @@
> +if TARGET_PINEPHONE_PRO_RK3399
> +
> +config SYS_BOARD
> + default "pinephone-pro-rk3399"
> +
> +config SYS_VENDOR
> + default "pine64"
> +
> +config SYS_CONFIG_NAME
> + default "pinephone-pro-rk3399"
> +
> +config BOARD_SPECIFIC_OPTIONS
> + def_bool y
> +
> +endif
> diff --git a/board/pine64/pinephone-pro-rk3399/MAINTAINERS b/board/pine64/pinephone-pro-rk3399/MAINTAINERS
> new file mode 100644
> index 00000000000..c923ff1be32
> --- /dev/null
> +++ b/board/pine64/pinephone-pro-rk3399/MAINTAINERS
> @@ -0,0 +1,8 @@
> +PINEPHONE_PRO
> +M: Peter Robinson <pbrobinson at gmail.com>
> +S: Maintained
> +F: board/pine64/rk3399-pinephone-pro/
> +F: include/configs/rk3399-pinephone-pro.h
> +F: arch/arm/dts/rk3399-pinephone-pro.dts
> +F: arch/arm/dts/rk3399-pinephone-pro-u-boot.dtsi
> +F: configs/pinephone-pro-rk3399_defconfig
> diff --git a/board/pine64/pinephone-pro-rk3399/Makefile b/board/pine64/pinephone-pro-rk3399/Makefile
> new file mode 100644
> index 00000000000..8d9203053e5
> --- /dev/null
> +++ b/board/pine64/pinephone-pro-rk3399/Makefile
> @@ -0,0 +1 @@
> +obj-y += pinephone-pro-rk3399.o
> diff --git a/board/pine64/pinephone-pro-rk3399/pinephone-pro-rk3399.c b/board/pine64/pinephone-pro-rk3399/pinephone-pro-rk3399.c
> new file mode 100644
> index 00000000000..eb639cd0d07
> --- /dev/null
> +++ b/board/pine64/pinephone-pro-rk3399/pinephone-pro-rk3399.c
> @@ -0,0 +1,76 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * (C) Copyright 2016 Rockchip Electronics Co., Ltd
> + * (C) Copyright 2022 Peter Robinson <pbrobinson at gmail.com>
> + */
> +
> +#include <common.h>
> +#include <dm.h>
> +#include <init.h>
> +#include <syscon.h>
> +#include <asm/io.h>
> +#include <asm/arch-rockchip/clock.h>
> +#include <asm/arch-rockchip/grf_rk3399.h>
> +#include <asm/arch-rockchip/hardware.h>
> +#include <asm/arch-rockchip/misc.h>
> +#include <power/regulator.h>
> +
> +#define GRF_IO_VSEL_BT565_SHIFT 0
> +#define PMUGRF_CON0_VSEL_SHIFT 8
> +
> +#ifndef CONFIG_SPL_BUILD
> +int board_early_init_f(void)
> +{
> + struct udevice *regulator;
> + int ret;
> +
> + ret = regulator_get_by_platname("vcc5v0_usb", ®ulator);
> + if (ret) {
> + pr_debug("%s vcc5v0_usb init fail! ret %d\n", __func__, ret);
> + goto out;
> + }
> +
> + ret = regulator_set_enable(regulator, true);
> + if (ret)
> + pr_debug("%s vcc5v0-host-en-gpio set fail! ret %d\n", __func__, ret);
> +
> +out:
> + return 0;
> +}
> +#endif
> +
> +#ifdef CONFIG_MISC_INIT_R
> +static void setup_iodomain(void)
> +{
> + struct rk3399_grf_regs *grf =
> + syscon_get_first_range(ROCKCHIP_SYSCON_GRF);
> + struct rk3399_pmugrf_regs *pmugrf =
> + syscon_get_first_range(ROCKCHIP_SYSCON_PMUGRF);
> +
> + /* BT565 is in 1.8v domain */
> + rk_setreg(&grf->io_vsel, 1 << GRF_IO_VSEL_BT565_SHIFT);
> +
> + /* Set GPIO1 1.8v/3.0v source select to PMU1830_VOL */
> + rk_setreg(&pmugrf->soc_con0, 1 << PMUGRF_CON0_VSEL_SHIFT);
> +}
> +
> +int misc_init_r(void)
> +{
> + const u32 cpuid_offset = 0x7;
> + const u32 cpuid_length = 0x10;
> + u8 cpuid[cpuid_length];
> + int ret;
> +
> + setup_iodomain();
> +
> + ret = rockchip_cpuid_from_efuse(cpuid_offset, cpuid_length, cpuid);
> + if (ret)
> + return ret;
> +
> + ret = rockchip_cpuid_set(cpuid, cpuid_length);
> + if (ret)
> + return ret;
> +
> + return ret;
> +}
> +#endif
> diff --git a/configs/pinephone-pro-rk3399_defconfig b/configs/pinephone-pro-rk3399_defconfig
> new file mode 100644
> index 00000000000..0082d3aec39
> --- /dev/null
> +++ b/configs/pinephone-pro-rk3399_defconfig
> @@ -0,0 +1,104 @@
> +CONFIG_ARM=y
> +CONFIG_SKIP_LOWLEVEL_INIT=y
> +CONFIG_COUNTER_FREQUENCY=24000000
> +CONFIG_ARCH_ROCKCHIP=y
> +CONFIG_SYS_TEXT_BASE=0x00200000
> +CONFIG_NR_DRAM_BANKS=1
> +CONFIG_ENV_SIZE=0x8000
> +CONFIG_ENV_OFFSET=0x3F8000
> +CONFIG_DEFAULT_DEVICE_TREE="rk3399-pinephone-pro"
> +CONFIG_ROCKCHIP_RK3399=y
> +CONFIG_TARGET_PINEPHONE_PRO_RK3399=y
> +CONFIG_DEBUG_UART_BASE=0xFF1A0000
> +CONFIG_DEBUG_UART_CLOCK=24000000
> +CONFIG_SPL_SPI_FLASH_SUPPORT=y
> +CONFIG_SPL_SPI=y
> +CONFIG_SYS_LOAD_ADDR=0x800800
> +CONFIG_DEBUG_UART=y
> +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
> +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x300000
> +CONFIG_BOOTDELAY=3
> +CONFIG_USE_PREBOOT=y
> +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-pinephone-pro.dtb"
> +CONFIG_DISPLAY_BOARDINFO_LATE=y
> +CONFIG_MISC_INIT_R=y
> +CONFIG_SPL_MAX_SIZE=0x2e000
> +CONFIG_SPL_PAD_TO=0x7f8000
> +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
> +CONFIG_SPL_BSS_START_ADDR=0x400000
> +CONFIG_SPL_BSS_MAX_SIZE=0x2000
> +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
> +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
> +CONFIG_SPL_STACK=0x400000
> +CONFIG_SPL_STACK_R=y
> +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
> +CONFIG_SPL_SPI_LOAD=y
> +CONFIG_TPL=y
> +CONFIG_CMD_BOOTZ=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_GPT=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_PCI=y
> +CONFIG_CMD_USB=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_TIME=y
> +CONFIG_CMD_PMIC=y
> +CONFIG_CMD_REGULATOR=y
> +CONFIG_SPL_OF_CONTROL=y
> +CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
> +CONFIG_ENV_IS_IN_SPI_FLASH=y
> +CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> +CONFIG_SPL_DM_SEQ_ALIAS=y
> +CONFIG_ROCKCHIP_GPIO=y
> +CONFIG_SYS_I2C_ROCKCHIP=y
> +CONFIG_DM_KEYBOARD=y
> +CONFIG_LED=y
> +CONFIG_LED_GPIO=y
> +CONFIG_MISC=y
> +CONFIG_ROCKCHIP_EFUSE=y
> +CONFIG_MMC_DW=y
> +CONFIG_MMC_DW_ROCKCHIP=y
> +CONFIG_MMC_SDHCI=y
> +CONFIG_MMC_SDHCI_SDMA=y
> +CONFIG_MMC_SDHCI_ROCKCHIP=y
> +CONFIG_SF_DEFAULT_BUS=1
> +CONFIG_SF_DEFAULT_SPEED=20000000
> +CONFIG_SPI_FLASH_GIGADEVICE=y
> +CONFIG_SPI_FLASH_WINBOND=y
> +CONFIG_PHY_ROCKCHIP_INNO_USB2=y
> +CONFIG_PHY_ROCKCHIP_TYPEC=y
> +CONFIG_DM_PMIC_FAN53555=y
> +CONFIG_PMIC_RK8XX=y
> +CONFIG_REGULATOR_PWM=y
> +CONFIG_REGULATOR_RK8XX=y
> +CONFIG_PWM_ROCKCHIP=y
> +CONFIG_RAM_RK3399_LPDDR4=y
> +CONFIG_DM_RESET=y
> +CONFIG_DM_RNG=y
> +CONFIG_RNG_ROCKCHIP=y
> +CONFIG_BAUDRATE=1500000
> +CONFIG_DEBUG_UART_SHIFT=2
> +CONFIG_ROCKCHIP_SPI=y
> +CONFIG_SYSRESET=y
> +CONFIG_USB=y
> +CONFIG_USB_XHCI_HCD=y
> +CONFIG_USB_XHCI_DWC3=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_EHCI_GENERIC=y
> +CONFIG_USB_OHCI_HCD=y
> +CONFIG_USB_OHCI_GENERIC=y
> +CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS=2
> +CONFIG_USB_DWC3=y
> +CONFIG_USB_DWC3_GENERIC=y
> +CONFIG_USB_KEYBOARD=y
> +CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
> +CONFIG_USB_HOST_ETHER=y
> +CONFIG_USB_ETHER_ASIX=y
> +CONFIG_USB_ETHER_RTL8152=y
> +CONFIG_DM_VIDEO=y
> +CONFIG_DISPLAY=y
> +CONFIG_VIDEO_ROCKCHIP=y
> +CONFIG_DISPLAY_ROCKCHIP_EDP=y
> +CONFIG_SPL_TINY_MEMSET=y
> +CONFIG_ERRNO_STR=y
> diff --git a/include/configs/pinephone-pro-rk3399.h b/include/configs/pinephone-pro-rk3399.h
> new file mode 100644
> index 00000000000..78017d6bcc3
> --- /dev/null
> +++ b/include/configs/pinephone-pro-rk3399.h
> @@ -0,0 +1,19 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Copyright (C) 2016 Rockchip Electronics Co., Ltd
> + * Copyright (C) 2022 Peter Robinson <pbrobinson at gmail.com>
> + */
> +
> +#ifndef __PINEPHONE_PRO_RK3399_H
> +#define __PINEPHONE_PRO_RK3399_H
> +
> +#define ROCKCHIP_DEVICE_SETTINGS \
> + "stdin=serial,usbkbd\0" \
> + "stdout=serial,vidconsole\0" \
> + "stderr=serial,vidconsole\0"
> +
> +#include <configs/rk3399_common.h>
> +
> +#define SDRAM_BANK_SIZE (2UL << 30)
> +
> +#endif
More information about the U-Boot
mailing list