[PATCH v1 4/4] arm: s5p4418: dm_serial: remove old code / add DEBUG_UART
Stefan Bosch
stefan_b at posteo.net
Sun Dec 18 13:26:47 CET 2022
Remove init of UART-clock and UART-reset in arch_cpu_init(). Add DEBUG_UART
to s5p4418_nanopi2_defconfig.
Signed-off-by: Stefan Bosch <stefan_b at posteo.net>
---
arch/arm/cpu/armv7/s5p4418/cpu.c | 29 -----------------------------
arch/arm/mach-nexell/clock.c | 2 +-
configs/s5p4418_nanopi2_defconfig | 8 +++++++-
include/configs/s5p4418_nanopi2.h | 8 +++-----
4 files changed, 11 insertions(+), 36 deletions(-)
diff --git a/arch/arm/cpu/armv7/s5p4418/cpu.c b/arch/arm/cpu/armv7/s5p4418/cpu.c
index 3baa761ec7..fcaafc0ff7 100644
--- a/arch/arm/cpu/armv7/s5p4418/cpu.c
+++ b/arch/arm/cpu/armv7/s5p4418/cpu.c
@@ -13,10 +13,8 @@
#include <asm/io.h>
#include <asm/arch/nexell.h>
#include <asm/arch/clk.h>
-#include <asm/arch/reset.h>
#include <asm/arch/tieoff.h>
#include <cpu_func.h>
-#include <linux/delay.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -45,39 +43,12 @@ static void cpu_soc_init(void)
nx_tieoff_set(NX_TIEOFF_CORTEXA9MP_TOP_QUADL2C_L2RET1N_1, 1);
}
-#ifdef CONFIG_PL011_SERIAL
-static void serial_device_init(void)
-{
- char dev[10];
- int id;
-
- sprintf(dev, "nx-uart.%d", CONFIG_CONS_INDEX);
- id = RESET_ID_UART0 + CONFIG_CONS_INDEX;
-
- struct clk *clk = clk_get((const char *)dev);
-
- /* reset control: Low active ___|--- */
- nx_rstcon_setrst(id, RSTCON_ASSERT);
- udelay(10);
- nx_rstcon_setrst(id, RSTCON_NEGATE);
- udelay(10);
-
- /* set clock */
- clk_disable(clk);
- clk_set_rate(clk, CONFIG_PL011_CLOCK);
- clk_enable(clk);
-}
-#endif
-
int arch_cpu_init(void)
{
flush_dcache_all();
cpu_soc_init();
clk_init();
- if (IS_ENABLED(CONFIG_PL011_SERIAL))
- serial_device_init();
-
return 0;
}
diff --git a/arch/arm/mach-nexell/clock.c b/arch/arm/mach-nexell/clock.c
index 24fa204ccd..59ffa26255 100644
--- a/arch/arm/mach-nexell/clock.c
+++ b/arch/arm/mach-nexell/clock.c
@@ -856,7 +856,7 @@ void __init clk_init(void)
}
/* prevent uart clock disable for low step debug message */
- #ifndef CONFIG_DEBUG_NX_UART
+ #ifndef CONFIG_DEBUG_UART
if (peri->dev_name) {
#ifdef CONFIG_BACKLIGHT_PWM
if (!strcmp(peri->dev_name, DEV_NAME_PWM))
diff --git a/configs/s5p4418_nanopi2_defconfig b/configs/s5p4418_nanopi2_defconfig
index f3a316513c..042037acfc 100644
--- a/configs/s5p4418_nanopi2_defconfig
+++ b/configs/s5p4418_nanopi2_defconfig
@@ -54,7 +54,7 @@ CONFIG_MMC_DW=y
CONFIG_PINCTRL=y
CONFIG_DM_PMIC=y
CONFIG_DM_REGULATOR=y
-CONFIG_CONS_INDEX=0
+
CONFIG_DM_VIDEO=y
CONFIG_VIDEO_LOGO=y
CONFIG_DISPLAY=y
@@ -67,3 +67,9 @@ CONFIG_SPLASH_SCREEN_ALIGN=y
CONFIG_SPLASH_SOURCE=y
CONFIG_BMP_24BPP=y
CONFIG_ERRNO_STR=y
+
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_PL011=y
+CONFIG_DEBUG_UART_BASE=0xC00A1000
+CONFIG_DEBUG_UART_CLOCK=150000000
+CONFIG_DEBUG_UART_SKIP_INIT=y
diff --git a/include/configs/s5p4418_nanopi2.h b/include/configs/s5p4418_nanopi2.h
index ae94f0ecc5..a6d3957dc1 100644
--- a/include/configs/s5p4418_nanopi2.h
+++ b/include/configs/s5p4418_nanopi2.h
@@ -78,11 +78,9 @@
/*-----------------------------------------------------------------------
* serial console configuration
*/
-#define CONFIG_PL011_CLOCK 50000000
-#define CONFIG_PL01x_PORTS {(void *)PHY_BASEADDR_UART0, \
- (void *)PHY_BASEADDR_UART1, \
- (void *)PHY_BASEADDR_UART2, \
- (void *)PHY_BASEADDR_UART3}
+
+/* 150MHz is the clock rate set by SPL (uart0) */
+#define CONFIG_PL011_CLOCK 150000000
/*-----------------------------------------------------------------------
* BACKLIGHT
--
2.17.1
More information about the U-Boot
mailing list