[PATCH v2 2/3] mmc: stm32_sdmmc2: remove privdata

Patrick Delaunay patrick.delaunay at foss.st.com
Thu Jun 30 10:01:46 CEST 2022


All the elements of privdata are static and build from device tree,
they are moved in platdata to prepare the support of ops
of_to_plat.

Signed-off-by: Patrick Delaunay <patrick.delaunay at foss.st.com>
---

(no changes since v1)

 drivers/mmc/stm32_sdmmc2.c | 145 ++++++++++++++++++-------------------
 1 file changed, 70 insertions(+), 75 deletions(-)

diff --git a/drivers/mmc/stm32_sdmmc2.c b/drivers/mmc/stm32_sdmmc2.c
index e3853b7fbfb..41f375b9d32 100644
--- a/drivers/mmc/stm32_sdmmc2.c
+++ b/drivers/mmc/stm32_sdmmc2.c
@@ -30,9 +30,6 @@
 struct stm32_sdmmc2_plat {
 	struct mmc_config cfg;
 	struct mmc mmc;
-};
-
-struct stm32_sdmmc2_priv {
 	fdt_addr_t base;
 	struct clk clk;
 	struct reset_ctl reset_ctl;
@@ -208,7 +205,7 @@ static void stm32_sdmmc2_start_data(struct udevice *dev,
 				    struct mmc_data *data,
 				    struct stm32_sdmmc2_ctx *ctx)
 {
-	struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+	struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
 	u32 data_ctrl, idmabase0;
 
 	/* Configure the SDMMC DPSM (Data Path State Machine) */
@@ -224,10 +221,10 @@ static void stm32_sdmmc2_start_data(struct udevice *dev,
 	}
 
 	/* Set the SDMMC DataLength value */
-	writel(ctx->data_length, priv->base + SDMMC_DLEN);
+	writel(ctx->data_length, plat->base + SDMMC_DLEN);
 
 	/* Write to SDMMC DCTRL */
-	writel(data_ctrl, priv->base + SDMMC_DCTRL);
+	writel(data_ctrl, plat->base + SDMMC_DCTRL);
 
 	/* Cache align */
 	ctx->cache_start = rounddown(idmabase0, ARCH_DMA_MINALIGN);
@@ -242,19 +239,19 @@ static void stm32_sdmmc2_start_data(struct udevice *dev,
 	flush_dcache_range(ctx->cache_start, ctx->cache_end);
 
 	/* Enable internal DMA */
-	writel(idmabase0, priv->base + SDMMC_IDMABASE0);
-	writel(SDMMC_IDMACTRL_IDMAEN, priv->base + SDMMC_IDMACTRL);
+	writel(idmabase0, plat->base + SDMMC_IDMABASE0);
+	writel(SDMMC_IDMACTRL_IDMAEN, plat->base + SDMMC_IDMACTRL);
 }
 
 static void stm32_sdmmc2_start_cmd(struct udevice *dev,
 				   struct mmc_cmd *cmd, u32 cmd_param,
 				   struct stm32_sdmmc2_ctx *ctx)
 {
-	struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+	struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
 	u32 timeout = 0;
 
-	if (readl(priv->base + SDMMC_CMD) & SDMMC_CMD_CPSMEN)
-		writel(0, priv->base + SDMMC_CMD);
+	if (readl(plat->base + SDMMC_CMD) & SDMMC_CMD_CPSMEN)
+		writel(0, plat->base + SDMMC_CMD);
 
 	cmd_param |= cmd->cmdidx | SDMMC_CMD_CPSMEN;
 	if (cmd->resp_type & MMC_RSP_PRESENT) {
@@ -277,30 +274,30 @@ static void stm32_sdmmc2_start_cmd(struct udevice *dev,
 	if (ctx->data_length) {
 		timeout = SDMMC_CMD_TIMEOUT;
 	} else {
-		writel(0, priv->base + SDMMC_DCTRL);
+		writel(0, plat->base + SDMMC_DCTRL);
 
 		if (cmd->resp_type & MMC_RSP_BUSY)
 			timeout = SDMMC_CMD_TIMEOUT;
 	}
 
 	/* Set the SDMMC Data TimeOut value */
-	writel(timeout, priv->base + SDMMC_DTIMER);
+	writel(timeout, plat->base + SDMMC_DTIMER);
 
 	/* Clear flags */
-	writel(SDMMC_ICR_STATIC_FLAGS, priv->base + SDMMC_ICR);
+	writel(SDMMC_ICR_STATIC_FLAGS, plat->base + SDMMC_ICR);
 
 	/* Set SDMMC argument value */
-	writel(cmd->cmdarg, priv->base + SDMMC_ARG);
+	writel(cmd->cmdarg, plat->base + SDMMC_ARG);
 
 	/* Set SDMMC command parameters */
-	writel(cmd_param, priv->base + SDMMC_CMD);
+	writel(cmd_param, plat->base + SDMMC_CMD);
 }
 
 static int stm32_sdmmc2_end_cmd(struct udevice *dev,
 				struct mmc_cmd *cmd,
 				struct stm32_sdmmc2_ctx *ctx)
 {
-	struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+	struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
 	u32 mask = SDMMC_STA_CTIMEOUT;
 	u32 status;
 	int ret;
@@ -314,7 +311,7 @@ static int stm32_sdmmc2_end_cmd(struct udevice *dev,
 	}
 
 	/* Polling status register */
-	ret = readl_poll_timeout(priv->base + SDMMC_STA, status, status & mask,
+	ret = readl_poll_timeout(plat->base + SDMMC_STA, status, status & mask,
 				 10000);
 
 	if (ret < 0) {
@@ -339,11 +336,11 @@ static int stm32_sdmmc2_end_cmd(struct udevice *dev,
 	}
 
 	if (status & SDMMC_STA_CMDREND && cmd->resp_type & MMC_RSP_PRESENT) {
-		cmd->response[0] = readl(priv->base + SDMMC_RESP1);
+		cmd->response[0] = readl(plat->base + SDMMC_RESP1);
 		if (cmd->resp_type & MMC_RSP_136) {
-			cmd->response[1] = readl(priv->base + SDMMC_RESP2);
-			cmd->response[2] = readl(priv->base + SDMMC_RESP3);
-			cmd->response[3] = readl(priv->base + SDMMC_RESP4);
+			cmd->response[1] = readl(plat->base + SDMMC_RESP2);
+			cmd->response[2] = readl(plat->base + SDMMC_RESP3);
+			cmd->response[3] = readl(plat->base + SDMMC_RESP4);
 		}
 
 		/* Wait for BUSYD0END flag if busy status is detected */
@@ -352,7 +349,7 @@ static int stm32_sdmmc2_end_cmd(struct udevice *dev,
 			mask = SDMMC_STA_DTIMEOUT | SDMMC_STA_BUSYD0END;
 
 			/* Polling status register */
-			ret = readl_poll_timeout(priv->base + SDMMC_STA,
+			ret = readl_poll_timeout(plat->base + SDMMC_STA,
 						 status, status & mask,
 						 SDMMC_BUSYD0END_TIMEOUT_US);
 
@@ -380,7 +377,7 @@ static int stm32_sdmmc2_end_data(struct udevice *dev,
 				 struct mmc_data *data,
 				 struct stm32_sdmmc2_ctx *ctx)
 {
-	struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+	struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
 	u32 mask = SDMMC_STA_DCRCFAIL | SDMMC_STA_DTIMEOUT |
 		   SDMMC_STA_IDMATE | SDMMC_STA_DATAEND;
 	u32 status;
@@ -390,9 +387,9 @@ static int stm32_sdmmc2_end_data(struct udevice *dev,
 	else
 		mask |= SDMMC_STA_TXUNDERR;
 
-	status = readl(priv->base + SDMMC_STA);
+	status = readl(plat->base + SDMMC_STA);
 	while (!(status & mask))
-		status = readl(priv->base + SDMMC_STA);
+		status = readl(plat->base + SDMMC_STA);
 
 	/*
 	 * Need invalidate the dcache again to avoid any
@@ -404,7 +401,7 @@ static int stm32_sdmmc2_end_data(struct udevice *dev,
 	if (status & SDMMC_STA_DCRCFAIL) {
 		dev_dbg(dev, "error SDMMC_STA_DCRCFAIL (0x%x) for cmd %d\n",
 			status, cmd->cmdidx);
-		if (readl(priv->base + SDMMC_DCOUNT))
+		if (readl(plat->base + SDMMC_DCOUNT))
 			ctx->dpsm_abort = true;
 		return -EILSEQ;
 	}
@@ -443,7 +440,7 @@ static int stm32_sdmmc2_end_data(struct udevice *dev,
 static int stm32_sdmmc2_send_cmd(struct udevice *dev, struct mmc_cmd *cmd,
 				 struct mmc_data *data)
 {
-	struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+	struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
 	struct stm32_sdmmc2_ctx ctx;
 	u32 cmdat = data ? SDMMC_CMD_CMDTRANS : 0;
 	int ret, retry = 3;
@@ -470,9 +467,9 @@ retry_cmd:
 		ret = stm32_sdmmc2_end_data(dev, cmd, data, &ctx);
 
 	/* Clear flags */
-	writel(SDMMC_ICR_STATIC_FLAGS, priv->base + SDMMC_ICR);
+	writel(SDMMC_ICR_STATIC_FLAGS, plat->base + SDMMC_ICR);
 	if (data)
-		writel(0x0, priv->base + SDMMC_IDMACTRL);
+		writel(0x0, plat->base + SDMMC_IDMACTRL);
 
 	/*
 	 * To stop Data Path State Machine, a stop_transmission command
@@ -493,7 +490,7 @@ retry_cmd:
 				       SDMMC_CMD_CMDSTOP, &ctx);
 		stm32_sdmmc2_end_cmd(dev, &stop_cmd, &ctx);
 
-		writel(SDMMC_ICR_STATIC_FLAGS, priv->base + SDMMC_ICR);
+		writel(SDMMC_ICR_STATIC_FLAGS, plat->base + SDMMC_ICR);
 	}
 
 	if ((ret != -ETIMEDOUT) && (ret != 0) && retry) {
@@ -512,17 +509,17 @@ retry_cmd:
  * This will reset the SDMMC to the reset state and the CPSM and DPSM
  * to the Idle state. SDMMC is disabled, Signals Hiz.
  */
-static void stm32_sdmmc2_reset(struct stm32_sdmmc2_priv *priv)
+static void stm32_sdmmc2_reset(struct stm32_sdmmc2_plat *plat)
 {
-	if (reset_valid(&priv->reset_ctl)) {
+	if (reset_valid(&plat->reset_ctl)) {
 		/* Reset */
-		reset_assert(&priv->reset_ctl);
+		reset_assert(&plat->reset_ctl);
 		udelay(2);
-		reset_deassert(&priv->reset_ctl);
+		reset_deassert(&plat->reset_ctl);
 	}
 
 	/* init the needed SDMMC register after reset */
-	writel(priv->pwr_reg_msk, priv->base + SDMMC_POWER);
+	writel(plat->pwr_reg_msk, plat->base + SDMMC_POWER);
 }
 
 /*
@@ -531,13 +528,13 @@ static void stm32_sdmmc2_reset(struct stm32_sdmmc2_priv *priv)
  * SDMMC_CMD and SDMMC_CK are driven low, to prevent the card from being
  * supplied through the signal lines.
  */
-static void stm32_sdmmc2_pwrcycle(struct stm32_sdmmc2_priv *priv)
+static void stm32_sdmmc2_pwrcycle(struct stm32_sdmmc2_plat *plat)
 {
-	if ((readl(priv->base + SDMMC_POWER) & SDMMC_POWER_PWRCTRL_MASK) ==
+	if ((readl(plat->base + SDMMC_POWER) & SDMMC_POWER_PWRCTRL_MASK) ==
 	    SDMMC_POWER_PWRCTRL_CYCLE)
 		return;
 
-	stm32_sdmmc2_reset(priv);
+	stm32_sdmmc2_reset(plat);
 }
 
 /*
@@ -546,10 +543,10 @@ static void stm32_sdmmc2_pwrcycle(struct stm32_sdmmc2_priv *priv)
  * Reset => Power-Cycle => Power-Off => Power
  *    PWRCTRL=10     PWCTRL=00    PWCTRL=11
  */
-static void stm32_sdmmc2_pwron(struct stm32_sdmmc2_priv *priv)
+static void stm32_sdmmc2_pwron(struct stm32_sdmmc2_plat *plat)
 {
 	u32 pwrctrl =
-		readl(priv->base + SDMMC_POWER) &  SDMMC_POWER_PWRCTRL_MASK;
+		readl(plat->base + SDMMC_POWER) &  SDMMC_POWER_PWRCTRL_MASK;
 
 	if (pwrctrl == SDMMC_POWER_PWRCTRL_ON)
 		return;
@@ -558,21 +555,21 @@ static void stm32_sdmmc2_pwron(struct stm32_sdmmc2_priv *priv)
 	 * it is the reset state here = the only managed by the driver
 	 */
 	if (pwrctrl == SDMMC_POWER_PWRCTRL_OFF) {
-		writel(SDMMC_POWER_PWRCTRL_CYCLE | priv->pwr_reg_msk,
-		       priv->base + SDMMC_POWER);
+		writel(SDMMC_POWER_PWRCTRL_CYCLE | plat->pwr_reg_msk,
+		       plat->base + SDMMC_POWER);
 	}
 
 	/*
 	 * the remaining case is SDMMC_POWER_PWRCTRL_CYCLE
 	 * switch to Power-Off state: SDMCC disable, signals drive 1
 	 */
-	writel(SDMMC_POWER_PWRCTRL_OFF | priv->pwr_reg_msk,
-	       priv->base + SDMMC_POWER);
+	writel(SDMMC_POWER_PWRCTRL_OFF | plat->pwr_reg_msk,
+	       plat->base + SDMMC_POWER);
 
 	/* After the 1ms delay set the SDMMC to power-on */
 	mdelay(1);
-	writel(SDMMC_POWER_PWRCTRL_ON | priv->pwr_reg_msk,
-	       priv->base + SDMMC_POWER);
+	writel(SDMMC_POWER_PWRCTRL_ON | plat->pwr_reg_msk,
+	       plat->base + SDMMC_POWER);
 
 	/* during the first 74 SDMMC_CK cycles the SDMMC is still disabled. */
 }
@@ -581,18 +578,18 @@ static void stm32_sdmmc2_pwron(struct stm32_sdmmc2_priv *priv)
 static int stm32_sdmmc2_set_ios(struct udevice *dev)
 {
 	struct mmc *mmc = mmc_get_mmc_dev(dev);
-	struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+	struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
 	u32 desired = mmc->clock;
-	u32 sys_clock = clk_get_rate(&priv->clk);
+	u32 sys_clock = clk_get_rate(&plat->clk);
 	u32 clk = 0;
 
 	dev_dbg(dev, "bus_with = %d, clock = %d\n",
 		mmc->bus_width, mmc->clock);
 
 	if (mmc->clk_disable)
-		stm32_sdmmc2_pwrcycle(priv);
+		stm32_sdmmc2_pwrcycle(plat);
 	else
-		stm32_sdmmc2_pwron(priv);
+		stm32_sdmmc2_pwron(plat);
 
 	/*
 	 * clk_div = 0 => command and data generated on SDMMCCLK falling edge
@@ -602,7 +599,7 @@ static int stm32_sdmmc2_set_ios(struct udevice *dev)
 	 * SDMMCCLK falling edge
 	 */
 	if (desired && ((sys_clock > desired) ||
-			IS_RISING_EDGE(priv->clk_reg_msk))) {
+			IS_RISING_EDGE(plat->clk_reg_msk))) {
 		clk = DIV_ROUND_UP(sys_clock, 2 * desired);
 		if (clk > SDMMC_CLKCR_CLKDIV_MAX)
 			clk = SDMMC_CLKCR_CLKDIV_MAX;
@@ -613,30 +610,30 @@ static int stm32_sdmmc2_set_ios(struct udevice *dev)
 	if (mmc->bus_width == 8)
 		clk |= SDMMC_CLKCR_WIDBUS_8;
 
-	writel(clk | priv->clk_reg_msk | SDMMC_CLKCR_HWFC_EN,
-	       priv->base + SDMMC_CLKCR);
+	writel(clk | plat->clk_reg_msk | SDMMC_CLKCR_HWFC_EN,
+	       plat->base + SDMMC_CLKCR);
 
 	return 0;
 }
 
 static int stm32_sdmmc2_getcd(struct udevice *dev)
 {
-	struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+	struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
 
 	dev_dbg(dev, "%s called\n", __func__);
 
-	if (dm_gpio_is_valid(&priv->cd_gpio))
-		return dm_gpio_get_value(&priv->cd_gpio);
+	if (dm_gpio_is_valid(&plat->cd_gpio))
+		return dm_gpio_get_value(&plat->cd_gpio);
 
 	return 1;
 }
 
 static int stm32_sdmmc2_host_power_cycle(struct udevice *dev)
 {
-	struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+	struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
 
-	writel(SDMMC_POWER_PWRCTRL_CYCLE | priv->pwr_reg_msk,
-	       priv->base + SDMMC_POWER);
+	writel(SDMMC_POWER_PWRCTRL_CYCLE | plat->pwr_reg_msk,
+	       plat->base + SDMMC_POWER);
 
 	return 0;
 }
@@ -650,7 +647,7 @@ static const struct dm_mmc_ops stm32_sdmmc2_ops = {
 
 static int stm32_sdmmc2_probe_level_translator(struct udevice *dev)
 {
-	struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
+	struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
 	struct gpio_desc cmd_gpio;
 	struct gpio_desc ck_gpio;
 	struct gpio_desc ckin_gpio;
@@ -660,7 +657,7 @@ static int stm32_sdmmc2_probe_level_translator(struct udevice *dev)
 	 * Assume the level translator is present if st,use-ckin is set.
 	 * This is to cater for DTs which do not implement this test.
 	 */
-	priv->clk_reg_msk |= SDMMC_CLKCR_SELCLKRX_CKIN;
+	plat->clk_reg_msk |= SDMMC_CLKCR_SELCLKRX_CKIN;
 
 	ret = gpio_request_by_name(dev, "st,cmd-gpios", 0, &cmd_gpio,
 				   GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
@@ -694,7 +691,7 @@ static int stm32_sdmmc2_probe_level_translator(struct udevice *dev)
 
 	/* Level translator is present if CK signal is propagated to CKIN */
 	if (!clk_hi || clk_lo)
-		priv->clk_reg_msk &= ~SDMMC_CLKCR_SELCLKRX_CKIN;
+		plat->clk_reg_msk &= ~SDMMC_CLKCR_SELCLKRX_CKIN;
 
 	dm_gpio_free(dev, &ckin_gpio);
 
@@ -712,34 +709,33 @@ static int stm32_sdmmc2_probe(struct udevice *dev)
 {
 	struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
 	struct stm32_sdmmc2_plat *plat = dev_get_plat(dev);
-	struct stm32_sdmmc2_priv *priv = dev_get_priv(dev);
 	struct mmc_config *cfg = &plat->cfg;
 	int ret;
 
-	priv->base = dev_read_addr(dev);
-	if (priv->base == FDT_ADDR_T_NONE)
+	plat->base = dev_read_addr(dev);
+	if (plat->base == FDT_ADDR_T_NONE)
 		return -EINVAL;
 
 	if (dev_read_bool(dev, "st,neg-edge"))
-		priv->clk_reg_msk |= SDMMC_CLKCR_NEGEDGE;
+		plat->clk_reg_msk |= SDMMC_CLKCR_NEGEDGE;
 	if (dev_read_bool(dev, "st,sig-dir"))
-		priv->pwr_reg_msk |= SDMMC_POWER_DIRPOL;
+		plat->pwr_reg_msk |= SDMMC_POWER_DIRPOL;
 	if (dev_read_bool(dev, "st,use-ckin"))
 		stm32_sdmmc2_probe_level_translator(dev);
 
-	ret = clk_get_by_index(dev, 0, &priv->clk);
+	ret = clk_get_by_index(dev, 0, &plat->clk);
 	if (ret)
 		return ret;
 
-	ret = clk_enable(&priv->clk);
+	ret = clk_enable(&plat->clk);
 	if (ret)
 		goto clk_free;
 
-	ret = reset_get_by_index(dev, 0, &priv->reset_ctl);
+	ret = reset_get_by_index(dev, 0, &plat->reset_ctl);
 	if (ret)
 		dev_dbg(dev, "No reset provided\n");
 
-	gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio,
+	gpio_request_by_name(dev, "cd-gpios", 0, &plat->cd_gpio,
 			     GPIOD_IS_IN);
 
 	cfg->f_min = 400000;
@@ -754,11 +750,11 @@ static int stm32_sdmmc2_probe(struct udevice *dev)
 	upriv->mmc = &plat->mmc;
 
 	/* SDMMC init */
-	stm32_sdmmc2_reset(priv);
+	stm32_sdmmc2_reset(plat);
 	return 0;
 
 clk_free:
-	clk_free(&priv->clk);
+	clk_free(&plat->clk);
 
 	return ret;
 }
@@ -782,6 +778,5 @@ U_BOOT_DRIVER(stm32_sdmmc2) = {
 	.ops = &stm32_sdmmc2_ops,
 	.probe = stm32_sdmmc2_probe,
 	.bind = stm32_sdmmc2_bind,
-	.priv_auto	= sizeof(struct stm32_sdmmc2_priv),
 	.plat_auto	= sizeof(struct stm32_sdmmc2_plat),
 };
-- 
2.25.1



More information about the U-Boot mailing list