Peculiar problem executing boot.scr

[Simon Glass]

+U-Boot Mailing List

On Mon, 14 Nov 2022 at 22:24, Terzidis Tasos <terzanasta at teemail.gr> wrote:
>
> Hello,
>
> > Can you post the whole console output so we can see version, etc.?
> Unfortunately I don’t have a serial console, so I will reproduce by writing the monitor output
>
> Boot.scr.uimg Script is
> printenv
> fatload mmc 0:1 ${kernel_addr_r} kernel7.img
> bootz ${kernel_addr_r} - ${fdt_addr}
>
>
> I manually load and run the script
>
> U-Boot> Fatload mmc 0:1 0x30000000 boot.scr.uimg
> 168 bytes read in 3 ms (54.7 KiB/s)
> U-Boot> source 0x30000000
> ## Executing script at 30000000
> ' - try 'help'd ' printenv
> 'ailed to load 'kernel7.img
> zimage: Bad magic!
> ' - try 'help' d '
>
> The version is
> U-Boot> version
> U-Boot 2023.01-rc1-00041-g0cbeed4f66-dirty (Nov 14 2022 - 18:44:50 +0200)
> Gcc (Rasbian 10.2.1 -6+rpi1) 10.2.1 20210110
> GNU id (GNU Binutils for Raspbian) 2.35.2
>
>
> I installed U-boot again at 14 November just in case I made something wrong
>
> The same error result I get, when let U-boot to automatically read and execute the script after autocount.
>
> Thank you
>
> Tasos Terzidis

This seems to be a mystery. Probably need to debug U-Boot and narrow
down what is happening. I assume that the board is reliable.

Regards,
Simon



>
> -----Original Message-----
> From: U-Boot [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Simon Glass
> Sent: Tuesday, November 15, 2022 12:51 AM
> To: terzanasta at yahoo.gr
> Cc: u-boot at lists.denx.de
> Subject: Re: Peculiar problem executing boot.scr
>
> Hi,
>
> On Mon, 14 Nov 2022 at 06:50, Tasos Terzidis <terzanasta at gmail.com> wrote:
> >
> > Hello,
> >
> > I have a very peculiar problem.
> >
> > I have a very simple boot.scr script so that u-boot can load it and run it.
> >
> > My set up is a Raspberry 3 B (32 bit)
> >
> > Sript is
> >
> > Fatload mmc 0:1 ${kernel_addr_r} kernel7.img
> >
> > Bootz ${kernel_addr_r} - ${fdt_addr}
> >
> >
> >
> > When u-boot stops autocounting, finds the script loads it and the error
> > message is
> >
> > -à    ‘ailed to find kernel7.img     ß--
> >
> >
> >
> > Instead of F for word Failed, prints ‘ailed.
> >
> >
> >
> > If I stop auto counting and enter the commands of script by hand it runs
> > and loads kernel as expected
> >
> >
> >
> > As a matter of fact whatever command I add to the script gives an error
> >
> > Example : if I add printenv the error is “can not find command”
> >
> >
> >
> > I can not understand what the problem is.
> >
> >
> >
> > Has anyone encountered such a problem ??
>
> Can you post the whole console output so we can see version, etc.?
>
> I cannot immediately even find that 'Failed to find %s' string in U-Boot.
>
> Regards,
> Simon
>
>
> --
> This email has been checked for viruses by Avast antivirus software.
> www.avast.com