[PATCH 03/12] arm: K3: Add basic support for J784S4 SoC definition
Tom Rini
trini at konsulko.com
Mon Nov 21 17:01:34 CET 2022
On Sat, Nov 19, 2022 at 12:59:24PM -0600, Hari Nagalla wrote:
> Add basic support for J784S4 SoC definition
>
> Signed-off-by: Hari Nagalla <hnagalla at ti.com>
> Signed-off-by: Apurva Nandan <a-nandan at ti.com>
> Signed-off-by: Bryan Bratloff <bb at ti.com>
> Signed-off-by: Nishant Menon <nm at ti.com>
[snip]
> diff --git a/include/configs/j784s4_evm.h b/include/configs/j784s4_evm.h
> new file mode 100644
> index 0000000000..c05c16bea1
> --- /dev/null
> +++ b/include/configs/j784s4_evm.h
> @@ -0,0 +1,146 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Configuration header file for K3 J784S4 EVM
> + *
> + * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
> + * Hari Nagalla <hnagalla at ti.com>
> + */
> +
> +#ifndef __CONFIG_J784S4_EVM_H
> +#define __CONFIG_J784S4_EVM_H
> +
> +#include <linux/sizes.h>
> +#include <config_distro_bootcmd.h>
> +#include <environment/ti/mmc.h>
> +#include <environment/ti/k3_rproc.h>
> +#include <environment/ti/ufs.h>
> +#include <environment/ti/k3_dfu.h>
Note that while we do enable DISTRO_DEFAULTS later (and this file should
be in that patch), we don't use it. Which isn't great, but isn't a huge
problem.
> +/* U-Boot general configuration */
> +#define EXTRA_ENV_J784S4_BOARD_SETTINGS \
> + "default_device_tree=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
> + "findfdt=" \
> + "setenv name_fdt ${default_device_tree};" \
> + "setenv fdtfile ${name_fdt}\0" \
> + "name_kern=Image\0" \
> + "console=ttyS2,115200n8\0" \
> + "args_all=setenv optargs earlycon=ns16550a,mmio32,0x02880000 " \
> + "${mtdparts}\0" \
> + "run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0"
> +
> +#define PARTS_DEFAULT \
> + /* Linux partitions */ \
> + "uuid_disk=${uuid_gpt_disk};" \
> + "name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0"
> +
> +#ifdef CONFIG_SYS_K3_SPL_ATF
> +#if defined(CONFIG_TARGET_J784S4_R5_EVM)
> +#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \
> + "addr_mcur5f0_0load=0x89000000\0" \
> + "name_mcur5f0_0fw=/lib/firmware/j7-mcu-r5f0_0-fw\0"
> +#elif defined(CONFIG_TARGET_J7200_R5_EVM)
> +#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \
> + "addr_mcur5f0_0load=0x89000000\0" \
> + "name_mcur5f0_0fw=/lib/firmware/j7200-mcu-r5f0_0-fw\0"
> +#endif /* CONFIG_TARGET_J784S4_R5_EVM */
> +#else
> +#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC ""
> +#endif /* CONFIG_SYS_K3_SPL_ATF */
> +
> +/* U-Boot MMC-specific configuration */
> +#define EXTRA_ENV_J784S4_BOARD_SETTINGS_MMC \
> + "boot=mmc\0" \
> + "mmcdev=1\0" \
> + "bootpart=1:2\0" \
> + "bootdir=/boot\0" \
> + EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \
> + "rd_spec=-\0" \
> + "init_mmc=run args_all args_mmc\0" \
> + "get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${name_fdt}\0" \
> + "get_overlay_mmc=" \
> + "fdt address ${fdtaddr};" \
> + "fdt resize 0x100000;" \
> + "for overlay in $name_overlays;" \
> + "do;" \
> + "load mmc ${bootpart} ${dtboaddr} ${bootdir}/${overlay} && " \
> + "fdt apply ${dtboaddr};" \
> + "done;\0" \
> + "partitions=" PARTS_DEFAULT \
> + "get_kern_mmc=load mmc ${bootpart} ${loadaddr} " \
> + "${bootdir}/${name_kern}\0" \
> + "get_fit_mmc=load mmc ${bootpart} ${addr_fit} " \
> + "${bootdir}/${name_fit}\0" \
> + "partitions=" PARTS_DEFAULT
> +
> +/* Set the default list of remote processors to boot */
> +#if defined(CONFIG_TARGET_J784S4_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
> +#ifdef DEFAULT_RPROCS
> +#undef DEFAULT_RPROCS
> +#endif
> +#endif
> +
> +#ifdef CONFIG_TARGET_J784S4_A72_EVM
> +#define DEFAULT_RPROCS "" \
> + "2 /lib/firmware/j784s4-main-r5f0_0-fw " \
> + "3 /lib/firmware/j784s4-main-r5f0_1-fw " \
> + "4 /lib/firmware/j784s4-main-r5f1_0-fw " \
> + "5 /lib/firmware/j784s4-main-r5f1_1-fw " \
> + "6 /lib/firmware/j784s4-c71_0-fw " \
> + "7 /lib/firmware/j784s4-c71_1-fw "
> +#endif /* CONFIG_TARGET_J784S4_A72_EVM */
> +
> +#ifdef CONFIG_TARGET_J7200_A72_EVM
> +#define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY \
> + "do_main_cpsw0_qsgmii_phyinit=1\0" \
> + "init_main_cpsw0_qsgmii_phy=gpio set gpio at 22_17;" \
> + "gpio clear gpio at 22_16\0" \
> + "main_cpsw0_qsgmii_phyinit=" \
> + "if test ${do_main_cpsw0_qsgmii_phyinit} -eq 1 && test ${dorprocboot} -eq 1 && " \
> + "test ${boot} = mmc; then " \
> + "run init_main_cpsw0_qsgmii_phy;" \
> + "fi;\0"
> +#define DEFAULT_RPROCS "" \
> + "2 /lib/firmware/j7200-main-r5f0_0-fw " \
> + "3 /lib/firmware/j7200-main-r5f0_1-fw "
> +#endif /* CONFIG_TARGET_J7200_A72_EVM */
> +
> +#ifndef EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
> +#define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
> +#endif
> +
> +/* set default dfu_bufsiz to 128KB (sector size of OSPI) */
> +#define EXTRA_ENV_DFUARGS \
> + DFU_ALT_INFO_MMC \
> + DFU_ALT_INFO_EMMC \
> + DFU_ALT_INFO_RAM \
> + DFU_ALT_INFO_OSPI
> +
> +/* Incorporate settings into the U-Boot environment */
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + DEFAULT_LINUX_BOOT_ENV \
> + DEFAULT_MMC_TI_ARGS \
> + DEFAULT_FIT_TI_ARGS \
> + EXTRA_ENV_J784S4_BOARD_SETTINGS \
> + EXTRA_ENV_J784S4_BOARD_SETTINGS_MMC \
> + EXTRA_ENV_RPROC_SETTINGS \
> + EXTRA_ENV_DFUARGS \
> + DEFAULT_UFS_TI_ARGS \
> + EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
As much of this as possible needs to be moved over to using the text
based environment file support instead.
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20221121/36137cbb/attachment.sig>
More information about the U-Boot
mailing list