[PATCH 0/6] Enable CONFIG_TIMER for all Kirwood / MVEBU boards
Tony Dinh
mibodhi at gmail.com
Thu Sep 1 03:38:55 CEST 2022
Hi Stefan,
On Wed, Aug 31, 2022 at 2:53 PM Tony Dinh <mibodhi at gmail.com> wrote:
>
> Hi Stefan,
>
> On Wed, Aug 31, 2022 at 8:08 AM Tony Dinh <mibodhi at gmail.com> wrote:
> >
> > Hi Stefan,
> >
> > On Wed, Aug 31, 2022 at 12:22 AM Stefan Roese <sr at denx.de> wrote:
> > >
> > > Hi Tony,
> > >
> > > On 31.08.22 08:30, Tony Dinh wrote:
> > > > Hi Stefan,
> > > >
> > > > On Tue, Aug 30, 2022 at 10:08 PM Stefan Roese <sr at denx.de> wrote:
> > > >>
> > > >> Hi Tony,
> > > >>
> > > >> On 31.08.22 07:02, Stefan Roese wrote:
> > > >>> Hi Tony,
> > > >>>
> > > >>> On 31.08.22 00:15, Tony Dinh wrote:
> > > >>>> Hi Stefan,
> > > >>>>
> > > >>>> On Tue, Aug 30, 2022 at 4:53 AM Stefan Roese <sr at denx.de> wrote:
> > > >>>>>
> > > >>>>> This patchset enhaces the recently added Orion Timer driver to support
> > > >>>>> all other Kirkwood & 32bit MVEBU Armada platforms. Additionally, this
> > > >>>>> timer support is then enabled per default for those platforms, so that
> > > >>>>> the board config files don't need to be changed. Also necessary is
> > > >>>>> some dts hacking, so that the timer DT node is available in early
> > > >>>>> U-Boot stages.
> > > >>>>>
> > > >>>>> I've successfully tested this patchset on an Armada XP board. Additional
> > > >>>>> test on other boards and platforms are very welcome and necessary.
> > > >>>>
> > > >>>> I've run some tests with the following 2 Kirkwood boards: Cloud
> > > >>>> Engines Pogo V4 88F6192 (with CONFIG_DM_RTC and CONFIG_RTC_EMULATION),
> > > >>>> and Marvell Sheevaplug 88F6281 (with CONFIG_DM_RTC and CONFIG_RTC_MV).
> > > >>>>
> > > >>>> It seems that it was either frozen or the timer did not expire at some
> > > >>>> subsequent sleep commands. Sometime it happened at 2nd command, some
> > > >>>> time at a later sleep command. For example,
> > > >>>>
> > > >>>> === Pogo V4 (the 1st sleep command works correctly at 10 seconds on my
> > > >>>> stopwatch)
> > > >>>>
> > > >>>> U-Boot 2022.10-rc3-00048-g66ccd87a9c-dirty (Aug 30 2022 - 13:38:24 -0700)
> > > >>>> Pogoplug V4
> > > >>>>
> > > >>>> Hit any key to stop autoboot: 0
> > > >>>> Pogo_V4> sleep 10
> > > >>>> Pogo_V4> sleep 31.5
> > > >>>> <frozen here>
> > > >>>
> > > >>> Does the cmd interface support fractial numbers? Please test again with
> > > >>> 31 or other integral numbers.
> > > >>>
> > > >>>> === Sheevaplug (RTC battery is old, so the date was not updated, but
> > > >>>> the clock seems OK)
> > > >>>>
> > > >>>> U-Boot 2022.10-rc3-00048-g66ccd87a9c-dirty (Aug 30 2022 - 14:14:24 -0700)
> > > >>>> Marvell-Sheevaplug
> > > >>>> Hit any key to stop autoboot: 0
> > > >>>> => date
> > > >>>> Date: 2000-01-01 (Saturday) Time: 0:02:55
> > > >>>> => sleep 10
> > > >>>> => date
> > > >>>> Date: 2000-01-01 (Saturday) Time: 0:03:18
> > > >>>> => sleep 10
> > > >>>> => sleep 20.1
> > > >>>> <frozen here>
> > > >>>>
> > > >>>> Please let me know what I can do (i.e. perhaps running a debug patch).
> > > >>>
> > > >>> Please see above. I assume that the fractional numbers result in very
> > > >>> long numbers internally, which result in a frozen / hanging system.
> > > >>
> > > >> I just tested fractional numbers on another board and hey, it just
> > > >> works. Learned something new. So we seem to have a problem here. Let
> > > >> me see, if I can find something.
> > > >
> > > > I've added debug printfs and possibly tracked down this issue. Seems
> > > > like in the 2nd call to sleep, get_timer(0) did not reset the start
> > > > number.
> > > >
> > > > cmd/sleep.c
> > > > static int do_sleep(struct cmd_tbl *cmdtp, int flag, int argc,
> > > > char *const argv[])
> > > > {
> > > > ulong start = get_timer(0);
> > > >
> > > > "do_sleep got a timer start = 2015" is the 1st call to sleep 5.
> > > > "do_sleep got a timer start = 16304" is the 2nd call to sleep 10.
> > > >
> > > > <BEGIN log>
> > > > Pogo_V4> sleep 5
> > > > do_sleep got a timer start = 2015
> > > > do_sleep delay = 5000
> > > > do_sleep delay = 5000
> > > > do_sleep sleeping...
> > > > do_sleep start 2015 curent 100
> > > > do_sleep start 2015 curent 200
> > > > do_sleep start 2015 curent 300
> > > > <snip>
> > > > do_sleep start 2015 curent 4900
> > > > do_sleep end of sleep ... current = 5000
> > > > Pogo_V4>
> > > >
> > > > Pogo_V4> sleep 10
> > > > do_sleep got a timer start = 16304
> > > > do_sleep delay = 10000
> > > > do_sleep delay = 10000
> > > > do_sleep sleeping...
> > > > <snip>
> > > >
> > > > <END log>
> > > >
> > > > So somewhere in the DM timer, "start" got accumulated. I think each
> > > > get_timer(0) should be a different timer instance. It looks like the
> > > > same timer instance is used again and again, causing the "start "to
> > > > grow bigger, and at one point it might just overflow.
> > >
> > > Frankly I don't really understand the problem you describe above. What
> > > do you mean with "timer instance"? get_timer(0) will return different
> > > values, depending on when you call this function. So where exactly is
> > > the problem with the 2nd "sleep 10" above?
> >
> > Please ignore what I said above! I misunderstood what get_timer()
> > does. I'll try again on another KIrkwood board to see if the behavior
> > will be the same.
>
> I've run the tests again with the Seagate GoFlex Home board (Kirkwood
> 88F6281). Below is the log, with my annotated comments starting with
> ****.
> In these tests, current = get_timer(start) is inside the while loop.
> And I printed out the start and current values when (current % 100 ==
> 0).
>
> <BEGIN LOG>
> U-Boot 2022.10-rc3-00048-g66ccd87a9c-dirty (Aug 31 2022 - 13:06:04 -0700)
> Seagate GoFlex Home
>
> SoC: Kirkwood 88F6281_A1
> DRAM: 128 MiB
> Core: 12 devices, 10 uclasses, devicetree: separate
> NAND: orion_timer_probe successful
> 256 MiB
> Loading Environment from NAND... OK
> In: serial
> Out: serial
> Err: serial
> Net: eth0: ethernet-controller at 72000
> Hit any key to stop autoboot: 0
>
> GoFlexHome> date
> Date: 2022-08-31 (Wednesday) Time: 20:43:03
>
> GoFlexHome> sleep 5
> do_sleep got a timer start = 1244
> do_sleep delay = 5000
> do_sleep delay = 5000
> do_sleep sleeping...
> do_sleep start 1244 current 100
> <snip>
> do_sleep start 1244 current 2300
> <snip>
> do_sleep start 1244 current 3700
> <snip>
> do_sleep start 1244 current 4800
> do_sleep start 1244 current 4900
> do_sleep end of sleep ... current = 5000
>
> **** working as intended
>
> GoFlexHome> sleep 10
> do_sleep got a timer start = 11428
> do_sleep delay = 10000
> do_sleep delay = 10000
> do_sleep sleeping...
> do_sleep start 11428 current 100
> <snip>
> do_sleep start 11428 current 2300
> <snip>
> do_sleep start 11428 current 9900
> do_sleep end of sleep ... current = 10000
>
> **** working as intended
>
> GoFlexHome> sleep 20.5
> do_sleep got a timer start = 15031
> do_sleep delay = 20000
> do_sleep delay = 20500
> do_sleep sleeping...
> do_sleep start 15031 current 100
> <snip>
> do_sleep start 15031 current 6400
> do_sleep end of sleep ... current = 4294952265
>
> *** Something strange happened here. current should be 6500, but it
> seems to have garbage. So the loop exits prematurely.
>
> GoFlexHome> sleep 20.5
> do_sleep got a timer start = 8339
> do_sleep delay = 20000
> do_sleep delay = 20500
> do_sleep sleeping...
> do_sleep start 8339 current 100
> do_sleep start 8339 current 200
> <snip>
> do_sleep start 8339 current 12300
> do_sleep start 8339 current 12400
> do_sleep start 8339 current 12500
> do_sleep start 8339 current 12600
> do_sleep start 8339 current 12700
> do_sleep start 8339 current 12800
> do_sleep start 8339 current 12900
> do_sleep start 8339 current 13000
> do_sleep start 8339 current 13100
>
> *** It was frozen right here. Control-C could not interrupt the loop,
> so my guess
> *** either it was stuck during the call to get_timer(). Or the current value
> *** overflowed and crashed the system.
>
> <END LOG>
>
> Finally, I removed the patch set, and rerun the sleep tests on this
> board. They all worked fine, I did not see anything strange.
>
Some ideas.
The get_timer() function looks wrong assigning an uint64_t to ulong.
lib/time.c
static uint64_t notrace tick_to_time(uint64_t tick)
uint64_t notrace get_ticks(void)
uint64_t __weak notrace get_ticks(void)
ulong __weak get_timer(ulong base)
{
return tick_to_time(get_ticks()) - base;
}
Most of the timer infrastructure is using uint64_t. I'm seeing this
__weak function get_timer was invoked in Kirkwood boards. Both in
sleep and timer commands.
Thanks,
Tony
More information about the U-Boot
mailing list