[PATCH 0/6] Enable CONFIG_TIMER for all Kirwood / MVEBU boards
Tony Dinh
mibodhi at gmail.com
Thu Sep 1 09:39:41 CEST 2022
Hi Simon,
On Wed, Aug 31, 2022 at 7:27 PM Simon Glass <sjg at chromium.org> wrote:
>
> Hi Tony,
>
> On Wed, 31 Aug 2022 at 19:39, Tony Dinh <mibodhi at gmail.com> wrote:
> >
> > Hi Stefan,
> >
> > On Wed, Aug 31, 2022 at 2:53 PM Tony Dinh <mibodhi at gmail.com> wrote:
> > >
> > > Hi Stefan,
> > >
> > > On Wed, Aug 31, 2022 at 8:08 AM Tony Dinh <mibodhi at gmail.com> wrote:
> > > >
> > > > Hi Stefan,
> > > >
> > > > On Wed, Aug 31, 2022 at 12:22 AM Stefan Roese <sr at denx.de> wrote:
> > > > >
> > > > > Hi Tony,
> > > > >
> > > > > On 31.08.22 08:30, Tony Dinh wrote:
> > > > > > Hi Stefan,
> > > > > >
> > > > > > On Tue, Aug 30, 2022 at 10:08 PM Stefan Roese <sr at denx.de> wrote:
> > > > > >>
> > > > > >> Hi Tony,
> > > > > >>
> > > > > >> On 31.08.22 07:02, Stefan Roese wrote:
> > > > > >>> Hi Tony,
> > > > > >>>
> > > > > >>> On 31.08.22 00:15, Tony Dinh wrote:
> > > > > >>>> Hi Stefan,
> > > > > >>>>
> > > > > >>>> On Tue, Aug 30, 2022 at 4:53 AM Stefan Roese <sr at denx.de> wrote:
> > > > > >>>>>
> > > > > >>>>> This patchset enhaces the recently added Orion Timer driver to support
> > > > > >>>>> all other Kirkwood & 32bit MVEBU Armada platforms. Additionally, this
> > > > > >>>>> timer support is then enabled per default for those platforms, so that
> > > > > >>>>> the board config files don't need to be changed. Also necessary is
> > > > > >>>>> some dts hacking, so that the timer DT node is available in early
> > > > > >>>>> U-Boot stages.
> > > > > >>>>>
> > > > > >>>>> I've successfully tested this patchset on an Armada XP board. Additional
> > > > > >>>>> test on other boards and platforms are very welcome and necessary.
> > > > > >>>>
> > > > > >>>> I've run some tests with the following 2 Kirkwood boards: Cloud
> > > > > >>>> Engines Pogo V4 88F6192 (with CONFIG_DM_RTC and CONFIG_RTC_EMULATION),
> > > > > >>>> and Marvell Sheevaplug 88F6281 (with CONFIG_DM_RTC and CONFIG_RTC_MV).
> > > > > >>>>
> > > > > >>>> It seems that it was either frozen or the timer did not expire at some
> > > > > >>>> subsequent sleep commands. Sometime it happened at 2nd command, some
> > > > > >>>> time at a later sleep command. For example,
> > > > > >>>>
> > > > > >>>> === Pogo V4 (the 1st sleep command works correctly at 10 seconds on my
> > > > > >>>> stopwatch)
> > > > > >>>>
> > > > > >>>> U-Boot 2022.10-rc3-00048-g66ccd87a9c-dirty (Aug 30 2022 - 13:38:24 -0700)
> > > > > >>>> Pogoplug V4
> > > > > >>>>
> > > > > >>>> Hit any key to stop autoboot: 0
> > > > > >>>> Pogo_V4> sleep 10
> > > > > >>>> Pogo_V4> sleep 31.5
> > > > > >>>> <frozen here>
> > > > > >>>
> > > > > >>> Does the cmd interface support fractial numbers? Please test again with
> > > > > >>> 31 or other integral numbers.
> > > > > >>>
> > > > > >>>> === Sheevaplug (RTC battery is old, so the date was not updated, but
> > > > > >>>> the clock seems OK)
> > > > > >>>>
> > > > > >>>> U-Boot 2022.10-rc3-00048-g66ccd87a9c-dirty (Aug 30 2022 - 14:14:24 -0700)
> > > > > >>>> Marvell-Sheevaplug
> > > > > >>>> Hit any key to stop autoboot: 0
> > > > > >>>> => date
> > > > > >>>> Date: 2000-01-01 (Saturday) Time: 0:02:55
> > > > > >>>> => sleep 10
> > > > > >>>> => date
> > > > > >>>> Date: 2000-01-01 (Saturday) Time: 0:03:18
> > > > > >>>> => sleep 10
> > > > > >>>> => sleep 20.1
> > > > > >>>> <frozen here>
> > > > > >>>>
> > > > > >>>> Please let me know what I can do (i.e. perhaps running a debug patch).
> > > > > >>>
> > > > > >>> Please see above. I assume that the fractional numbers result in very
> > > > > >>> long numbers internally, which result in a frozen / hanging system.
> > > > > >>
> > > > > >> I just tested fractional numbers on another board and hey, it just
> > > > > >> works. Learned something new. So we seem to have a problem here. Let
> > > > > >> me see, if I can find something.
> > > > > >
> > > > > > I've added debug printfs and possibly tracked down this issue. Seems
> > > > > > like in the 2nd call to sleep, get_timer(0) did not reset the start
> > > > > > number.
> > > > > >
> > > > > > cmd/sleep.c
> > > > > > static int do_sleep(struct cmd_tbl *cmdtp, int flag, int argc,
> > > > > > char *const argv[])
> > > > > > {
> > > > > > ulong start = get_timer(0);
> > > > > >
> > > > > > "do_sleep got a timer start = 2015" is the 1st call to sleep 5.
> > > > > > "do_sleep got a timer start = 16304" is the 2nd call to sleep 10.
> > > > > >
> > > > > > <BEGIN log>
> > > > > > Pogo_V4> sleep 5
> > > > > > do_sleep got a timer start = 2015
> > > > > > do_sleep delay = 5000
> > > > > > do_sleep delay = 5000
> > > > > > do_sleep sleeping...
> > > > > > do_sleep start 2015 curent 100
> > > > > > do_sleep start 2015 curent 200
> > > > > > do_sleep start 2015 curent 300
> > > > > > <snip>
> > > > > > do_sleep start 2015 curent 4900
> > > > > > do_sleep end of sleep ... current = 5000
> > > > > > Pogo_V4>
> > > > > >
> > > > > > Pogo_V4> sleep 10
> > > > > > do_sleep got a timer start = 16304
> > > > > > do_sleep delay = 10000
> > > > > > do_sleep delay = 10000
> > > > > > do_sleep sleeping...
> > > > > > <snip>
> > > > > >
> > > > > > <END log>
> > > > > >
> > > > > > So somewhere in the DM timer, "start" got accumulated. I think each
> > > > > > get_timer(0) should be a different timer instance. It looks like the
> > > > > > same timer instance is used again and again, causing the "start "to
> > > > > > grow bigger, and at one point it might just overflow.
> > > > >
> > > > > Frankly I don't really understand the problem you describe above. What
> > > > > do you mean with "timer instance"? get_timer(0) will return different
> > > > > values, depending on when you call this function. So where exactly is
> > > > > the problem with the 2nd "sleep 10" above?
> > > >
> > > > Please ignore what I said above! I misunderstood what get_timer()
> > > > does. I'll try again on another KIrkwood board to see if the behavior
> > > > will be the same.
> > >
> > > I've run the tests again with the Seagate GoFlex Home board (Kirkwood
> > > 88F6281). Below is the log, with my annotated comments starting with
> > > ****.
> > > In these tests, current = get_timer(start) is inside the while loop.
> > > And I printed out the start and current values when (current % 100 ==
> > > 0).
> > >
> > > <BEGIN LOG>
> > > U-Boot 2022.10-rc3-00048-g66ccd87a9c-dirty (Aug 31 2022 - 13:06:04 -0700)
> > > Seagate GoFlex Home
> > >
> > > SoC: Kirkwood 88F6281_A1
> > > DRAM: 128 MiB
> > > Core: 12 devices, 10 uclasses, devicetree: separate
> > > NAND: orion_timer_probe successful
> > > 256 MiB
> > > Loading Environment from NAND... OK
> > > In: serial
> > > Out: serial
> > > Err: serial
> > > Net: eth0: ethernet-controller at 72000
> > > Hit any key to stop autoboot: 0
> > >
> > > GoFlexHome> date
> > > Date: 2022-08-31 (Wednesday) Time: 20:43:03
> > >
> > > GoFlexHome> sleep 5
> > > do_sleep got a timer start = 1244
> > > do_sleep delay = 5000
> > > do_sleep delay = 5000
> > > do_sleep sleeping...
> > > do_sleep start 1244 current 100
> > > <snip>
> > > do_sleep start 1244 current 2300
> > > <snip>
> > > do_sleep start 1244 current 3700
> > > <snip>
> > > do_sleep start 1244 current 4800
> > > do_sleep start 1244 current 4900
> > > do_sleep end of sleep ... current = 5000
> > >
> > > **** working as intended
> > >
> > > GoFlexHome> sleep 10
> > > do_sleep got a timer start = 11428
> > > do_sleep delay = 10000
> > > do_sleep delay = 10000
> > > do_sleep sleeping...
> > > do_sleep start 11428 current 100
> > > <snip>
> > > do_sleep start 11428 current 2300
> > > <snip>
> > > do_sleep start 11428 current 9900
> > > do_sleep end of sleep ... current = 10000
> > >
> > > **** working as intended
> > >
> > > GoFlexHome> sleep 20.5
> > > do_sleep got a timer start = 15031
> > > do_sleep delay = 20000
> > > do_sleep delay = 20500
> > > do_sleep sleeping...
> > > do_sleep start 15031 current 100
> > > <snip>
> > > do_sleep start 15031 current 6400
> > > do_sleep end of sleep ... current = 4294952265
> > >
> > > *** Something strange happened here. current should be 6500, but it
> > > seems to have garbage. So the loop exits prematurely.
> > >
> > > GoFlexHome> sleep 20.5
> > > do_sleep got a timer start = 8339
> > > do_sleep delay = 20000
> > > do_sleep delay = 20500
> > > do_sleep sleeping...
> > > do_sleep start 8339 current 100
> > > do_sleep start 8339 current 200
> > > <snip>
> > > do_sleep start 8339 current 12300
> > > do_sleep start 8339 current 12400
> > > do_sleep start 8339 current 12500
> > > do_sleep start 8339 current 12600
> > > do_sleep start 8339 current 12700
> > > do_sleep start 8339 current 12800
> > > do_sleep start 8339 current 12900
> > > do_sleep start 8339 current 13000
> > > do_sleep start 8339 current 13100
> > >
> > > *** It was frozen right here. Control-C could not interrupt the loop,
> > > so my guess
> > > *** either it was stuck during the call to get_timer(). Or the current value
> > > *** overflowed and crashed the system.
> > >
> > > <END LOG>
> > >
> > > Finally, I removed the patch set, and rerun the sleep tests on this
> > > board. They all worked fine, I did not see anything strange.
> > >
> >
> > Some ideas.
> >
> > The get_timer() function looks wrong assigning an uint64_t to ulong.
> >
> > lib/time.c
> >
> > static uint64_t notrace tick_to_time(uint64_t tick)
> > uint64_t notrace get_ticks(void)
> > uint64_t __weak notrace get_ticks(void)
> >
> > ulong __weak get_timer(ulong base)
> > {
> > return tick_to_time(get_ticks()) - base;
> > }
> >
> > Most of the timer infrastructure is using uint64_t. I'm seeing this
> > __weak function get_timer was invoked in Kirkwood boards. Both in
> > sleep and timer commands.
>
> The get_ticks() thing can run at 1MHz but the timer is 1KHz, so that
> is why we don't need a u64 for the timer.
Thanks for your explanation! However, would you agree that code is
problematic and needed some improvement ? IOW, depending what the
compiler does, it might return the 1st 32 bit of the 64-bit integer
result?
Thanks,
Tony
> Regards,
> Simon
More information about the U-Boot
mailing list