[PATCH] arm: orion5: Completely remove Orion5 platform support
Stefan Roese
sr at denx.de
Fri Sep 2 07:34:41 CEST 2022
Hi Mauri,
On 01.09.22 16:23, Mauri Sandberg wrote:
> Hi Stefan!
>
> On 1.9.2022 12.06, Stefan Roese wrote:
>> Hi Mauri,
>>
>> On 01.09.22 11:03, Pali Rohár wrote:
>>> + Mauri
>>>
>>> I think that we could wait a bit as Mauri is interested in Orion
>>> support and in last weeks we have been debugging and adding Orion
>>> support for pci-mvebu.c kernel driver.
>>
>> Ah, thanks Pali.
>>
>> Mauri, please let us know what your plans are with Orion5 support in
>> mainline U-Boot. Without a board using the code its practically dead and
>> will be removed completely soon. But if you have plans to add at least
>> one Orion5 based board to mainline then this is very welcome of course.
>>
>
> Yes, I am trying to get a device tree version of D-Link DNS323 (Orion 1)
> pushed to mainline kernel but I have not had any time to think about
> U-boot on that regard. To be honest I didn't even know there was any
> existing support in U-boot. In my development so far I have settled with
> the original vendor U-boot, which is quite crippled, though.
>
> So, if you are under pressure to clean up your source tree I cannot be
> there to stop the progress because as of now my plans are vague at best.
I'm in no real hurry - it's more a cleanup. I can postpone this patch
removing this platforms a few months.
> First off I would have to be educated in adding support for a new
> target. Does having a proper device tree help?
Yes, this does help. Even though I have to admit, that I'm not sure
which essential drivers for Orion support DT based probing, as this
platform was not really maintained properly in the last years.
> Second thing is that I
> cannot say anything about schedule as this is a hobby of mine. I think
> I have an Olimex JTAG thingy somewhere, but I don't think there exists a
> config file for OpenOCD so I am missing a few pieces before I can get
> going.
Might be that you many things by TFTP'ing the new U-Boot image to the
board and starting it directly from RAM via go? It's worth a try. This
helps with the not so low-level stuff like device drivers (e.g.
network). And it makes sense to restrict your board support for the
really necessary devices for Linux booting. Meaning, if you don't need
e.g. USB just drop it (for now).
But as mentioned above, I'll just postpone the Orion arch drop for
a while.
Thanks,
Stefan
> Cheers,
> Mauri
>
>> Thanks,
>> Stefan
>>
>>> On Thursday 01 September 2022 10:53:28 Stefan Roese wrote:
>>>> As there is no Orion5 based target in mainline U-Boot any more, let's
>>>> completely remove the support for this pretty old Marvell platform.
>>>>
>>>> Signed-off-by: Stefan Roese <sr at denx.de>
>>>> Cc: Tony Dinh <mibodhi at gmail.com>
>>>> Cc: Pali Rohár <pali at kernel.org>
>>>> Cc: Michael Walle <michael at walle.cc>
>>>> ---
>>>> arch/arm/Kconfig | 9 -
>>>> arch/arm/Makefile | 1 -
>>>> arch/arm/mach-orion5x/Kconfig | 13 -
>>>> arch/arm/mach-orion5x/Makefile | 26 --
>>>> arch/arm/mach-orion5x/cpu.c | 298 ------------------
>>>> arch/arm/mach-orion5x/dram.c | 58 ----
>>>> arch/arm/mach-orion5x/include/mach/cpu.h | 242 --------------
>>>> .../arm/mach-orion5x/include/mach/mv88f5182.h | 23 --
>>>> arch/arm/mach-orion5x/include/mach/orion5x.h | 66 ----
>>>> arch/arm/mach-orion5x/lowlevel_init.S | 286 -----------------
>>>> arch/arm/mach-orion5x/timer.c | 174 ----------
>>>> arch/arm/mach-orion5x/u-boot-spl.lds | 60 ----
>>>> drivers/i2c/mvtwsi.c | 4 +-
>>>> drivers/net/Kconfig | 2 +-
>>>> drivers/net/mvgbe.c | 2 -
>>>> drivers/usb/host/Kconfig | 2 +-
>>>> drivers/usb/host/ehci-marvell.c | 2 -
>>>> include/configs/mv-common.h | 1 -
>>>> 18 files changed, 3 insertions(+), 1266 deletions(-)
>>>> delete mode 100644 arch/arm/mach-orion5x/Kconfig
>>>> delete mode 100644 arch/arm/mach-orion5x/Makefile
>>>> delete mode 100644 arch/arm/mach-orion5x/cpu.c
>>>> delete mode 100644 arch/arm/mach-orion5x/dram.c
>>>> delete mode 100644 arch/arm/mach-orion5x/include/mach/cpu.h
>>>> delete mode 100644 arch/arm/mach-orion5x/include/mach/mv88f5182.h
>>>> delete mode 100644 arch/arm/mach-orion5x/include/mach/orion5x.h
>>>> delete mode 100644 arch/arm/mach-orion5x/lowlevel_init.S
>>>> delete mode 100644 arch/arm/mach-orion5x/timer.c
>>>> delete mode 100644 arch/arm/mach-orion5x/u-boot-spl.lds
>>>>
>>>> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
>>>> index 60f524a2d118..206e34412b3e 100644
>>>> --- a/arch/arm/Kconfig
>>>> +++ b/arch/arm/Kconfig
>>>> @@ -637,13 +637,6 @@ config ARCH_MVEBU
>>>> select SPI
>>>> imply CMD_DM
>>>> -config ARCH_ORION5X
>>>> - bool "Marvell Orion"
>>>> - select CPU_ARM926EJS
>>>> - select GPIO_EXTRA_HEADER
>>>> - select SPL_SEPARATE_BSS if SPL
>>>> - select TIMER
>>>> -
>>>> config TARGET_STV0991
>>>> bool "Support stv0991"
>>>> select CPU_V7A
>>>> @@ -2246,8 +2239,6 @@ source "arch/arm/mach-omap2/Kconfig"
>>>> source "arch/arm/cpu/armv8/fsl-layerscape/Kconfig"
>>>> -source "arch/arm/mach-orion5x/Kconfig"
>>>> -
>>>> source "arch/arm/mach-owl/Kconfig"
>>>> source "arch/arm/mach-rmobile/Kconfig"
>>>> diff --git a/arch/arm/Makefile b/arch/arm/Makefile
>>>> index 1f4a1d57883b..680c152cae5e 100644
>>>> --- a/arch/arm/Makefile
>>>> +++ b/arch/arm/Makefile
>>>> @@ -72,7 +72,6 @@ machine-$(CONFIG_ARCH_MVEBU) += mvebu
>>>> machine-$(CONFIG_ARCH_NEXELL) += nexell
>>>> machine-$(CONFIG_ARCH_NPCM) += npcm
>>>> machine-$(CONFIG_ARCH_OMAP2PLUS) += omap2
>>>> -machine-$(CONFIG_ARCH_ORION5X) += orion5x
>>>> machine-$(CONFIG_ARCH_OWL) += owl
>>>> machine-$(CONFIG_ARCH_RMOBILE) += rmobile
>>>> machine-$(CONFIG_ARCH_ROCKCHIP) += rockchip
>>>> diff --git a/arch/arm/mach-orion5x/Kconfig
>>>> b/arch/arm/mach-orion5x/Kconfig
>>>> deleted file mode 100644
>>>> index e677211b2e91..000000000000
>>>> --- a/arch/arm/mach-orion5x/Kconfig
>>>> +++ /dev/null
>>>> @@ -1,13 +0,0 @@
>>>> -if ARCH_ORION5X
>>>> -
>>>> -config 88F5182
>>>> - bool
>>>> -
>>>> -config FEROCEON
>>>> - bool
>>>> -
>>>> -config SYS_SOC
>>>> - default "orion5x"
>>>> -
>>>> -
>>>> -endif
>>>> diff --git a/arch/arm/mach-orion5x/Makefile
>>>> b/arch/arm/mach-orion5x/Makefile
>>>> deleted file mode 100644
>>>> index a8b87f6d7103..000000000000
>>>> --- a/arch/arm/mach-orion5x/Makefile
>>>> +++ /dev/null
>>>> @@ -1,26 +0,0 @@
>>>> -# SPDX-License-Identifier: GPL-2.0+
>>>> -#
>>>> -# Copyright (C) 2010 Albert ARIBAUD <albert.u.boot at aribaud.net>
>>>> -#
>>>> -# Based on original Kirkwood support which is
>>>> -# (C) Copyright 2009
>>>> -# Marvell Semiconductor <www.marvell.com>
>>>> -# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
>>>> -
>>>> -obj-y = cpu.o
>>>> -obj-y += dram.o
>>>> -obj-y += timer.o
>>>> -
>>>> -ifndef CONFIG_$(SPL_)SKIP_LOWLEVEL_INIT
>>>> -obj-y += lowlevel_init.o
>>>> -endif
>>>> -
>>>> -# some files can only build in ARM or THUMB2, not THUMB1
>>>> -
>>>> -ifdef CONFIG_$(SPL_)SYS_THUMB_BUILD
>>>> -ifndef CONFIG_HAS_THUMB2
>>>> -
>>>> -CFLAGS_cpu.o := -marm
>>>> -
>>>> -endif
>>>> -endif
>>>> diff --git a/arch/arm/mach-orion5x/cpu.c b/arch/arm/mach-orion5x/cpu.c
>>>> deleted file mode 100644
>>>> index ffae9a01e37c..000000000000
>>>> --- a/arch/arm/mach-orion5x/cpu.c
>>>> +++ /dev/null
>>>> @@ -1,298 +0,0 @@
>>>> -// SPDX-License-Identifier: GPL-2.0+
>>>> -/*
>>>> - * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot at aribaud.net>
>>>> - *
>>>> - * Based on original Kirkwood support which is
>>>> - * (C) Copyright 2009
>>>> - * Marvell Semiconductor <www.marvell.com>
>>>> - * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
>>>> - */
>>>> -
>>>> -#include <common.h>
>>>> -#include <cpu_func.h>
>>>> -#include <init.h>
>>>> -#include <net.h>
>>>> -#include <netdev.h>
>>>> -#include <asm/cache.h>
>>>> -#include <asm/io.h>
>>>> -#include <u-boot/md5.h>
>>>> -#include <asm/arch/cpu.h>
>>>> -
>>>> -#define BUFLEN 16
>>>> -
>>>> -void reset_cpu(void)
>>>> -{
>>>> - struct orion5x_cpu_registers *cpureg =
>>>> - (struct orion5x_cpu_registers *)ORION5X_CPU_REG_BASE;
>>>> -
>>>> - writel(readl(&cpureg->rstoutn_mask) | (1 << 2),
>>>> - &cpureg->rstoutn_mask);
>>>> - writel(readl(&cpureg->sys_soft_rst) | 1,
>>>> - &cpureg->sys_soft_rst);
>>>> - while (1)
>>>> - ;
>>>> -}
>>>> -
>>>> -/*
>>>> - * Compute Window Size field value from size expressed in bytes
>>>> - * Used with the Base register to set the address window size and
>>>> location.
>>>> - * Must be programmed from LSB to MSB as sequence of ones followed by
>>>> - * sequence of zeros. The number of ones specifies the size of the
>>>> window in
>>>> - * 64 KiB granularity (e.g., a value of 0x00FF specifies 256 = 16 MiB).
>>>> - * NOTES:
>>>> - * 1) A sizeval equal to 0x0 specifies 4 GiB.
>>>> - * 2) A return value of 0x0 specifies 64 KiB.
>>>> - */
>>>> -unsigned int orion5x_winctrl_calcsize(unsigned int sizeval)
>>>> -{
>>>> - /*
>>>> - * Calculate the number of 64 KiB blocks needed minus one
>>>> (rounding up).
>>>> - * For sizeval > 0 this is equivalent to:
>>>> - * sizeval = (u32) ceil((double) sizeval / 65536.0) - 1
>>>> - */
>>>> - sizeval = (sizeval - 1) >> 16;
>>>> -
>>>> - /*
>>>> - * Propagate 'one' bits to the right by 'oring' them.
>>>> - * We need only treat bits 15-0.
>>>> - */
>>>> - sizeval |= sizeval >> 1; /* 'Or' bit 15 onto bit 14 */
>>>> - sizeval |= sizeval >> 2; /* 'Or' bits 15-14 onto bits 13-12 */
>>>> - sizeval |= sizeval >> 4; /* 'Or' bits 15-12 onto bits 11-8 */
>>>> - sizeval |= sizeval >> 8; /* 'Or' bits 15-8 onto bits 7-0*/
>>>> -
>>>> - return sizeval;
>>>> -}
>>>> -
>>>> -/*
>>>> - * orion5x_config_adr_windows - Configure address Windows
>>>> - *
>>>> - * There are 8 address windows supported by Orion5x Soc to addess
>>>> different
>>>> - * devices. Each window can be configured for size, BAR and remap addr
>>>> - * Below configuration is standard for most of the cases
>>>> - *
>>>> - * If remap function not used, remap_lo must be set as base
>>>> - *
>>>> - * NOTES:
>>>> - *
>>>> - * 1) in order to avoid windows with inconsistent control and base
>>>> values
>>>> - * (which could prevent access to BOOTCS and hence execution from
>>>> FLASH)
>>>> - * always disable window before writing the base value then
>>>> reenable it
>>>> - * by writing the control value.
>>>> - *
>>>> - * 2) in order to avoid losing access to BOOTCS when disabling
>>>> window 7,
>>>> - * first configure window 6 for BOOTCS, then configure window 7
>>>> for BOOTCS,
>>>> - * then configure windows 6 for its own target.
>>>> - *
>>>> - * Reference Documentation:
>>>> - * Mbus-L to Mbus Bridge Registers Configuration.
>>>> - * (Sec 25.1 and 25.3 of Datasheet)
>>>> - */
>>>> -int orion5x_config_adr_windows(void)
>>>> -{
>>>> - struct orion5x_win_registers *winregs =
>>>> - (struct orion5x_win_registers *)ORION5X_CPU_WIN_BASE;
>>>> -
>>>> -/* Disable window 0, configure it for its intended target, enable
>>>> it. */
>>>> - writel(0, &winregs[0].ctrl);
>>>> - writel(ORION5X_ADR_PCIE_MEM, &winregs[0].base);
>>>> - writel(ORION5X_ADR_PCIE_MEM_REMAP_LO, &winregs[0].remap_lo);
>>>> - writel(ORION5X_ADR_PCIE_MEM_REMAP_HI, &winregs[0].remap_hi);
>>>> - writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCIE_MEM,
>>>> - ORION5X_TARGET_PCIE, ORION5X_ATTR_PCIE_MEM,
>>>> - ORION5X_WIN_ENABLE), &winregs[0].ctrl);
>>>> -/* Disable window 1, configure it for its intended target, enable
>>>> it. */
>>>> - writel(0, &winregs[1].ctrl);
>>>> - writel(ORION5X_ADR_PCIE_IO, &winregs[1].base);
>>>> - writel(ORION5X_ADR_PCIE_IO_REMAP_LO, &winregs[1].remap_lo);
>>>> - writel(ORION5X_ADR_PCIE_IO_REMAP_HI, &winregs[1].remap_hi);
>>>> - writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCIE_IO,
>>>> - ORION5X_TARGET_PCIE, ORION5X_ATTR_PCIE_IO,
>>>> - ORION5X_WIN_ENABLE), &winregs[1].ctrl);
>>>> -/* Disable window 2, configure it for its intended target, enable
>>>> it. */
>>>> - writel(0, &winregs[2].ctrl);
>>>> - writel(ORION5X_ADR_PCI_MEM, &winregs[2].base);
>>>> - writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCI_MEM,
>>>> - ORION5X_TARGET_PCI, ORION5X_ATTR_PCI_MEM,
>>>> - ORION5X_WIN_ENABLE), &winregs[2].ctrl);
>>>> -/* Disable window 3, configure it for its intended target, enable
>>>> it. */
>>>> - writel(0, &winregs[3].ctrl);
>>>> - writel(ORION5X_ADR_PCI_IO, &winregs[3].base);
>>>> - writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCI_IO,
>>>> - ORION5X_TARGET_PCI, ORION5X_ATTR_PCI_IO,
>>>> - ORION5X_WIN_ENABLE), &winregs[3].ctrl);
>>>> -/* Disable window 4, configure it for its intended target, enable
>>>> it. */
>>>> - writel(0, &winregs[4].ctrl);
>>>> - writel(ORION5X_ADR_DEV_CS0, &winregs[4].base);
>>>> - writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_DEV_CS0,
>>>> - ORION5X_TARGET_DEVICE, ORION5X_ATTR_DEV_CS0,
>>>> - ORION5X_WIN_ENABLE), &winregs[4].ctrl);
>>>> -/* Disable window 5, configure it for its intended target, enable
>>>> it. */
>>>> - writel(0, &winregs[5].ctrl);
>>>> - writel(ORION5X_ADR_DEV_CS1, &winregs[5].base);
>>>> - writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_DEV_CS1,
>>>> - ORION5X_TARGET_DEVICE, ORION5X_ATTR_DEV_CS1,
>>>> - ORION5X_WIN_ENABLE), &winregs[5].ctrl);
>>>> -/* Disable window 6, configure it for FLASH, enable it. */
>>>> - writel(0, &winregs[6].ctrl);
>>>> - writel(ORION5X_ADR_BOOTROM, &winregs[6].base);
>>>> - writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_BOOTROM,
>>>> - ORION5X_TARGET_DEVICE, ORION5X_ATTR_BOOTROM,
>>>> - ORION5X_WIN_ENABLE), &winregs[6].ctrl);
>>>> -/* Disable window 7, configure it for FLASH, enable it. */
>>>> - writel(0, &winregs[7].ctrl);
>>>> - writel(ORION5X_ADR_BOOTROM, &winregs[7].base);
>>>> - writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_BOOTROM,
>>>> - ORION5X_TARGET_DEVICE, ORION5X_ATTR_BOOTROM,
>>>> - ORION5X_WIN_ENABLE), &winregs[7].ctrl);
>>>> -/* Disable window 6, configure it for its intended target, enable
>>>> it. */
>>>> - writel(0, &winregs[6].ctrl);
>>>> - writel(ORION5X_ADR_DEV_CS2, &winregs[6].base);
>>>> - writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_DEV_CS2,
>>>> - ORION5X_TARGET_DEVICE, ORION5X_ATTR_DEV_CS2,
>>>> - ORION5X_WIN_ENABLE), &winregs[6].ctrl);
>>>> -
>>>> - return 0;
>>>> -}
>>>> -
>>>> -/*
>>>> - * Orion5x identification is done through PCIE space.
>>>> - */
>>>> -
>>>> -u32 orion5x_device_id(void)
>>>> -{
>>>> - return readl(PCIE_DEV_ID_OFF) >> 16;
>>>> -}
>>>> -
>>>> -u32 orion5x_device_rev(void)
>>>> -{
>>>> - return readl(PCIE_DEV_REV_OFF) & 0xff;
>>>> -}
>>>> -
>>>> -#if defined(CONFIG_DISPLAY_CPUINFO)
>>>> -
>>>> -/* Display device and revision IDs.
>>>> - * This function must cover all known device/revision
>>>> - * combinations, not only the one for which u-boot is
>>>> - * compiled; this way, one can identify actual HW in
>>>> - * case of a mismatch.
>>>> - */
>>>> -int print_cpuinfo(void)
>>>> -{
>>>> - char dev_str[7]; /* room enough for 0x0000 plus null byte */
>>>> - char rev_str[5]; /* room enough for 0x00 plus null byte */
>>>> - char *dev_name = NULL;
>>>> - char *rev_name = NULL;
>>>> -
>>>> - u32 dev = orion5x_device_id();
>>>> - u32 rev = orion5x_device_rev();
>>>> -
>>>> - if (dev == MV88F5181_DEV_ID) {
>>>> - dev_name = "MV88F5181";
>>>> - if (rev == MV88F5181_REV_B1)
>>>> - rev_name = "B1";
>>>> - else if (rev == MV88F5181L_REV_A1) {
>>>> - dev_name = "MV88F5181L";
>>>> - rev_name = "A1";
>>>> - } else if (rev == MV88F5181L_REV_A0) {
>>>> - dev_name = "MV88F5181L";
>>>> - rev_name = "A0";
>>>> - }
>>>> - } else if (dev == MV88F5182_DEV_ID) {
>>>> - dev_name = "MV88F5182";
>>>> - if (rev == MV88F5182_REV_A2)
>>>> - rev_name = "A2";
>>>> - } else if (dev == MV88F5281_DEV_ID) {
>>>> - dev_name = "MV88F5281";
>>>> - if (rev == MV88F5281_REV_D2)
>>>> - rev_name = "D2";
>>>> - else if (rev == MV88F5281_REV_D1)
>>>> - rev_name = "D1";
>>>> - else if (rev == MV88F5281_REV_D0)
>>>> - rev_name = "D0";
>>>> - } else if (dev == MV88F6183_DEV_ID) {
>>>> - dev_name = "MV88F6183";
>>>> - if (rev == MV88F6183_REV_B0)
>>>> - rev_name = "B0";
>>>> - }
>>>> - if (dev_name == NULL) {
>>>> - sprintf(dev_str, "0x%04x", dev);
>>>> - dev_name = dev_str;
>>>> - }
>>>> - if (rev_name == NULL) {
>>>> - sprintf(rev_str, "0x%02x", rev);
>>>> - rev_name = rev_str;
>>>> - }
>>>> -
>>>> - printf("SoC: Orion5x %s-%s\n", dev_name, rev_name);
>>>> -
>>>> - return 0;
>>>> -}
>>>> -#endif /* CONFIG_DISPLAY_CPUINFO */
>>>> -
>>>> -#ifdef CONFIG_ARCH_CPU_INIT
>>>> -int arch_cpu_init(void)
>>>> -{
>>>> - /* Enable and invalidate L2 cache in write through mode */
>>>> - invalidate_l2_cache();
>>>> -
>>>> -#ifdef CONFIG_SPL_BUILD
>>>> - orion5x_config_adr_windows();
>>>> -#endif
>>>> -
>>>> - return 0;
>>>> -}
>>>> -#endif /* CONFIG_ARCH_CPU_INIT */
>>>> -
>>>> -/*
>>>> - * SOC specific misc init
>>>> - */
>>>> -#if defined(CONFIG_ARCH_MISC_INIT)
>>>> -int arch_misc_init(void)
>>>> -{
>>>> - u32 temp;
>>>> -
>>>> - /*CPU streaming & write allocate */
>>>> - temp = readfr_extra_feature_reg();
>>>> - temp &= ~(1 << 28); /* disable wr alloc */
>>>> - writefr_extra_feature_reg(temp);
>>>> -
>>>> - temp = readfr_extra_feature_reg();
>>>> - temp &= ~(1 << 29); /* streaming disabled */
>>>> - writefr_extra_feature_reg(temp);
>>>> -
>>>> - /* L2Cache settings */
>>>> - temp = readfr_extra_feature_reg();
>>>> - /* Disable L2C pre fetch - Set bit 24 */
>>>> - temp |= (1 << 24);
>>>> - /* enable L2C - Set bit 22 */
>>>> - temp |= (1 << 22);
>>>> - writefr_extra_feature_reg(temp);
>>>> -
>>>> - icache_enable();
>>>> - /* Change reset vector to address 0x0 */
>>>> - temp = get_cr();
>>>> - set_cr(temp & ~CR_V);
>>>> -
>>>> - /* Set CPIOs and MPPs - values provided by board
>>>> - include file */
>>>> - writel(ORION5X_MPP0_7, ORION5X_MPP_BASE+0x00);
>>>> - writel(ORION5X_MPP8_15, ORION5X_MPP_BASE+0x04);
>>>> - writel(ORION5X_MPP16_23, ORION5X_MPP_BASE+0x50);
>>>> - writel(ORION5X_GPIO_OUT_VALUE, ORION5X_GPIO_BASE+0x00);
>>>> - writel(ORION5X_GPIO_OUT_ENABLE, ORION5X_GPIO_BASE+0x04);
>>>> - writel(ORION5X_GPIO_IN_POLARITY, ORION5X_GPIO_BASE+0x0c);
>>>> -
>>>> - /* initialize timer */
>>>> - timer_init_r();
>>>> - return 0;
>>>> -}
>>>> -#endif /* CONFIG_ARCH_MISC_INIT */
>>>> -
>>>> -#ifdef CONFIG_MVGBE
>>>> -int cpu_eth_init(struct bd_info *bis)
>>>> -{
>>>> - mvgbe_initialize(bis);
>>>> - return 0;
>>>> -}
>>>> -#endif
>>>> diff --git a/arch/arm/mach-orion5x/dram.c b/arch/arm/mach-orion5x/dram.c
>>>> deleted file mode 100644
>>>> index c9a3750e48de..000000000000
>>>> --- a/arch/arm/mach-orion5x/dram.c
>>>> +++ /dev/null
>>>> @@ -1,58 +0,0 @@
>>>> -// SPDX-License-Identifier: GPL-2.0+
>>>> -/*
>>>> - * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot at aribaud.net>
>>>> - *
>>>> - * Based on original Kirkwood support which is
>>>> - * (C) Copyright 2009
>>>> - * Marvell Semiconductor <www.marvell.com>
>>>> - * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
>>>> - */
>>>> -
>>>> -#include <common.h>
>>>> -#include <config.h>
>>>> -#include <init.h>
>>>> -#include <asm/arch/cpu.h>
>>>> -#include <asm/global_data.h>
>>>> -
>>>> -DECLARE_GLOBAL_DATA_PTR;
>>>> -
>>>> -/*
>>>> - * orion5x_sdram_bar - reads SDRAM Base Address Register
>>>> - */
>>>> -u32 orion5x_sdram_bar(enum memory_bank bank)
>>>> -{
>>>> - struct orion5x_ddr_addr_decode_registers *winregs =
>>>> - (struct orion5x_ddr_addr_decode_registers *)
>>>> - ORION5X_DRAM_BASE;
>>>> -
>>>> - u32 result = 0;
>>>> - u32 enable = 0x01 & winregs[bank].size;
>>>> -
>>>> - if ((!enable) || (bank > BANK3))
>>>> - return 0;
>>>> -
>>>> - result = winregs[bank].base;
>>>> - return result;
>>>> -}
>>>> -int dram_init (void)
>>>> -{
>>>> - /* dram_init must store complete ramsize in gd->ram_size */
>>>> - gd->ram_size = get_ram_size(
>>>> - (long *) orion5x_sdram_bar(0),
>>>> - CONFIG_MAX_RAM_BANK_SIZE);
>>>> - return 0;
>>>> -}
>>>> -
>>>> -int dram_init_banksize(void)
>>>> -{
>>>> - int i;
>>>> -
>>>> - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
>>>> - gd->bd->bi_dram[i].start = orion5x_sdram_bar(i);
>>>> - gd->bd->bi_dram[i].size = get_ram_size(
>>>> - (long *) (gd->bd->bi_dram[i].start),
>>>> - CONFIG_MAX_RAM_BANK_SIZE);
>>>> - }
>>>> -
>>>> - return 0;
>>>> -}
>>>> diff --git a/arch/arm/mach-orion5x/include/mach/cpu.h
>>>> b/arch/arm/mach-orion5x/include/mach/cpu.h
>>>> deleted file mode 100644
>>>> index c3ff89669e45..000000000000
>>>> --- a/arch/arm/mach-orion5x/include/mach/cpu.h
>>>> +++ /dev/null
>>>> @@ -1,242 +0,0 @@
>>>> -/* SPDX-License-Identifier: GPL-2.0+ */
>>>> -/*
>>>> - * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot at aribaud.net>
>>>> - *
>>>> - * Based on original Kirorion5x_ood support which is
>>>> - * (C) Copyright 2009
>>>> - * Marvell Semiconductor <www.marvell.com>
>>>> - * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
>>>> - */
>>>> -
>>>> -#ifndef _ORION5X_CPU_H
>>>> -#define _ORION5X_CPU_H
>>>> -
>>>> -#include <asm/system.h>
>>>> -
>>>> -#ifndef __ASSEMBLY__
>>>> -
>>>> -#define ORION5X_CPU_WIN_CTRL_DATA(size, target, attr, en) (en |
>>>> (target << 4) \
>>>> - | (attr << 8) | (orion5x_winctrl_calcsize(size) << 16))
>>>> -
>>>> -#define ORION5XGBE_PORT_SERIAL_CONTROL1_REG(_x) \
>>>> - ((_x ? ORION5X_EGIGA0_BASE : ORION5X_EGIGA1_BASE) + 0x44c)
>>>> -
>>>> -enum memory_bank {
>>>> - BANK0,
>>>> - BANK1,
>>>> - BANK2,
>>>> - BANK3
>>>> -};
>>>> -
>>>> -enum orion5x_cpu_winen {
>>>> - ORION5X_WIN_DISABLE,
>>>> - ORION5X_WIN_ENABLE
>>>> -};
>>>> -
>>>> -enum orion5x_cpu_target {
>>>> - ORION5X_TARGET_DRAM = 0,
>>>> - ORION5X_TARGET_DEVICE = 1,
>>>> - ORION5X_TARGET_PCI = 3,
>>>> - ORION5X_TARGET_PCIE = 4,
>>>> - ORION5X_TARGET_SASRAM = 9
>>>> -};
>>>> -
>>>> -enum orion5x_cpu_attrib {
>>>> - ORION5X_ATTR_DRAM_CS0 = 0x0e,
>>>> - ORION5X_ATTR_DRAM_CS1 = 0x0d,
>>>> - ORION5X_ATTR_DRAM_CS2 = 0x0b,
>>>> - ORION5X_ATTR_DRAM_CS3 = 0x07,
>>>> - ORION5X_ATTR_PCI_MEM = 0x59,
>>>> - ORION5X_ATTR_PCI_IO = 0x51,
>>>> - ORION5X_ATTR_PCIE_MEM = 0x59,
>>>> - ORION5X_ATTR_PCIE_IO = 0x51,
>>>> - ORION5X_ATTR_SASRAM = 0x00,
>>>> - ORION5X_ATTR_DEV_CS0 = 0x1e,
>>>> - ORION5X_ATTR_DEV_CS1 = 0x1d,
>>>> - ORION5X_ATTR_DEV_CS2 = 0x1b,
>>>> - ORION5X_ATTR_BOOTROM = 0x0f
>>>> -};
>>>> -
>>>> -/*
>>>> - * Device Address MAP BAR values
>>>> - *
>>>> - * All addresses and sizes not defined by board code
>>>> - * will be given default values here.
>>>> - */
>>>> -
>>>> -#if !defined (ORION5X_ADR_PCIE_MEM)
>>>> -#define ORION5X_ADR_PCIE_MEM 0x90000000
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_ADR_PCIE_MEM_REMAP_LO)
>>>> -#define ORION5X_ADR_PCIE_MEM_REMAP_LO 0x90000000
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_ADR_PCIE_MEM_REMAP_HI)
>>>> -#define ORION5X_ADR_PCIE_MEM_REMAP_HI 0
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_SZ_PCIE_MEM)
>>>> -#define ORION5X_SZ_PCIE_MEM (128*1024*1024)
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_ADR_PCIE_IO)
>>>> -#define ORION5X_ADR_PCIE_IO 0xf0000000
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_ADR_PCIE_IO_REMAP_LO)
>>>> -#define ORION5X_ADR_PCIE_IO_REMAP_LO 0xf0000000
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_ADR_PCIE_IO_REMAP_HI)
>>>> -#define ORION5X_ADR_PCIE_IO_REMAP_HI 0
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_SZ_PCIE_IO)
>>>> -#define ORION5X_SZ_PCIE_IO (64*1024)
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_ADR_PCI_MEM)
>>>> -#define ORION5X_ADR_PCI_MEM 0x98000000
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_SZ_PCI_MEM)
>>>> -#define ORION5X_SZ_PCI_MEM (128*1024*1024)
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_ADR_PCI_IO)
>>>> -#define ORION5X_ADR_PCI_IO 0xf0100000
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_SZ_PCI_IO)
>>>> -#define ORION5X_SZ_PCI_IO (64*1024)
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_ADR_DEV_CS0)
>>>> -#define ORION5X_ADR_DEV_CS0 0xfa000000
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_SZ_DEV_CS0)
>>>> -#define ORION5X_SZ_DEV_CS0 (2*1024*1024)
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_ADR_DEV_CS1)
>>>> -#define ORION5X_ADR_DEV_CS1 0xf8000000
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_SZ_DEV_CS1)
>>>> -#define ORION5X_SZ_DEV_CS1 (32*1024*1024)
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_ADR_DEV_CS2)
>>>> -#define ORION5X_ADR_DEV_CS2 0xfa800000
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_SZ_DEV_CS2)
>>>> -#define ORION5X_SZ_DEV_CS2 (1*1024*1024)
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_ADR_BOOTROM)
>>>> -#define ORION5X_ADR_BOOTROM 0xFFF80000
>>>> -#endif
>>>> -
>>>> -#if !defined (ORION5X_SZ_BOOTROM)
>>>> -#define ORION5X_SZ_BOOTROM (512*1024)
>>>> -#endif
>>>> -
>>>> -/*
>>>> - * PCIE registers are used for SoC device ID and revision
>>>> - */
>>>> -#define PCIE_DEV_ID_OFF (ORION5X_REG_PCIE_BASE + 0x0000)
>>>> -#define PCIE_DEV_REV_OFF (ORION5X_REG_PCIE_BASE + 0x0008)
>>>> -
>>>> -/*
>>>> - * The following definitions are intended for identifying
>>>> - * the real device and revision on which u-boot is running
>>>> - * even if it was compiled only for a specific one. Thus,
>>>> - * these constants must not be considered chip-specific.
>>>> - */
>>>> -
>>>> -/* Orion-1 (88F5181) and Orion-VoIP (88F5181L) */
>>>> -#define MV88F5181_DEV_ID 0x5181
>>>> -#define MV88F5181_REV_B1 3
>>>> -#define MV88F5181L_REV_A0 8
>>>> -#define MV88F5181L_REV_A1 9
>>>> -/* Orion-NAS (88F5182) */
>>>> -#define MV88F5182_DEV_ID 0x5182
>>>> -#define MV88F5182_REV_A2 2
>>>> -/* Orion-2 (88F5281) */
>>>> -#define MV88F5281_DEV_ID 0x5281
>>>> -#define MV88F5281_REV_D0 4
>>>> -#define MV88F5281_REV_D1 5
>>>> -#define MV88F5281_REV_D2 6
>>>> -/* Orion-1-90 (88F6183) */
>>>> -#define MV88F6183_DEV_ID 0x6183
>>>> -#define MV88F6183_REV_B0 3
>>>> -
>>>> -/*
>>>> - * read feroceon core extra feature register
>>>> - * using co-proc instruction
>>>> - */
>>>> -static inline unsigned int readfr_extra_feature_reg(void)
>>>> -{
>>>> - unsigned int val;
>>>> - asm volatile ("mrc p15, 1, %0, c15, c1, 0 @ readfr exfr" : "=r"
>>>> - (val) : : "cc");
>>>> - return val;
>>>> -}
>>>> -
>>>> -/*
>>>> - * write feroceon core extra feature register
>>>> - * using co-proc instruction
>>>> - */
>>>> -static inline void writefr_extra_feature_reg(unsigned int val)
>>>> -{
>>>> - asm volatile ("mcr p15, 1, %0, c15, c1, 0 @ writefr exfr" : : "r"
>>>> - (val) : "cc");
>>>> - isb();
>>>> -}
>>>> -
>>>> -/*
>>>> - * AHB to Mbus Bridge Registers
>>>> - * Source: 88F5182 User Manual, Appendix A, section A.4
>>>> - * Note: only windows 0 and 1 have remap capability.
>>>> - */
>>>> -struct orion5x_win_registers {
>>>> - u32 ctrl;
>>>> - u32 base;
>>>> - u32 remap_lo;
>>>> - u32 remap_hi;
>>>> -};
>>>> -
>>>> -/*
>>>> - * CPU control and status Registers
>>>> - * Source: 88F5182 User Manual, Appendix A, section A.4
>>>> - */
>>>> -struct orion5x_cpu_registers {
>>>> - u32 config; /*0x20100 */
>>>> - u32 ctrl_stat; /*0x20104 */
>>>> - u32 rstoutn_mask; /* 0x20108 */
>>>> - u32 sys_soft_rst; /* 0x2010C */
>>>> - u32 ahb_mbus_cause_irq; /* 0x20110 */
>>>> - u32 ahb_mbus_mask_irq; /* 0x20114 */
>>>> -};
>>>> -
>>>> -/*
>>>> - * DDR SDRAM Controller Address Decode Registers
>>>> - * Source: 88F5182 User Manual, Appendix A, section A.5.1
>>>> - */
>>>> -struct orion5x_ddr_addr_decode_registers {
>>>> - u32 base;
>>>> - u32 size;
>>>> -};
>>>> -
>>>> -/*
>>>> - * functions
>>>> - */
>>>> -u32 orion5x_device_id(void);
>>>> -u32 orion5x_device_rev(void);
>>>> -unsigned int orion5x_winctrl_calcsize(unsigned int sizeval);
>>>> -void timer_init_r(void);
>>>> -#endif /* __ASSEMBLY__ */
>>>> -#endif /* _ORION5X_CPU_H */
>>>> diff --git a/arch/arm/mach-orion5x/include/mach/mv88f5182.h
>>>> b/arch/arm/mach-orion5x/include/mach/mv88f5182.h
>>>> deleted file mode 100644
>>>> index 0e9fe0dc51af..000000000000
>>>> --- a/arch/arm/mach-orion5x/include/mach/mv88f5182.h
>>>> +++ /dev/null
>>>> @@ -1,23 +0,0 @@
>>>> -/* SPDX-License-Identifier: GPL-2.0+ */
>>>> -/*
>>>> - * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot at aribaud.net>
>>>> - *
>>>> - * Based on original Kirkwood 88F6182 support which is
>>>> - * (C) Copyright 2009
>>>> - * Marvell Semiconductor <www.marvell.com>
>>>> - * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
>>>> - *
>>>> - * Header file for Feroceon CPU core 88F5182 SOC.
>>>> - */
>>>> -
>>>> -#ifndef _CONFIG_88F5182_H
>>>> -#define _CONFIG_88F5182_H
>>>> -
>>>> -/* SOC specific definitions */
>>>> -#define F88F5182_REGS_PHYS_BASE 0xf1000000
>>>> -#define ORION5X_REGS_PHY_BASE F88F5182_REGS_PHYS_BASE
>>>> -
>>>> -/* TCLK Core Clock defination */
>>>> -#define CONFIG_SYS_TCLK 166000000 /* 166MHz */
>>>> -
>>>> -#endif /* _CONFIG_88F5182_H */
>>>> diff --git a/arch/arm/mach-orion5x/include/mach/orion5x.h
>>>> b/arch/arm/mach-orion5x/include/mach/orion5x.h
>>>> deleted file mode 100644
>>>> index 4b1b0b0f3716..000000000000
>>>> --- a/arch/arm/mach-orion5x/include/mach/orion5x.h
>>>> +++ /dev/null
>>>> @@ -1,66 +0,0 @@
>>>> -/* SPDX-License-Identifier: GPL-2.0+ */
>>>> -/*
>>>> - * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot at aribaud.net>
>>>> - *
>>>> - * Based on original Kirkwood support which is
>>>> - * (C) Copyright 2009
>>>> - * Marvell Semiconductor <www.marvell.com>
>>>> - * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
>>>> - *
>>>> - * Header file for Marvell's Orion SoC with Feroceon CPU core.
>>>> - */
>>>> -
>>>> -#ifndef _ASM_ARCH_ORION5X_H
>>>> -#define _ASM_ARCH_ORION5X_H
>>>> -
>>>> -#if defined(CONFIG_FEROCEON)
>>>> -
>>>> -/* SOC specific definations */
>>>> -#define ORION5X_REGISTER(x) (ORION5X_REGS_PHY_BASE + x)
>>>> -
>>>> -/* Documented registers */
>>>> -#define ORION5X_DRAM_BASE (ORION5X_REGISTER(0x01500))
>>>> -#define ORION5X_TWSI_BASE (ORION5X_REGISTER(0x11000))
>>>> -#define ORION5X_UART0_BASE (ORION5X_REGISTER(0x12000))
>>>> -#define ORION5X_UART1_BASE (ORION5X_REGISTER(0x12100))
>>>> -#define ORION5X_MPP_BASE (ORION5X_REGISTER(0x10000))
>>>> -#define ORION5X_GPIO_BASE (ORION5X_REGISTER(0x10100))
>>>> -#define ORION5X_CPU_WIN_BASE (ORION5X_REGISTER(0x20000))
>>>> -#define ORION5X_CPU_REG_BASE (ORION5X_REGISTER(0x20100))
>>>> -#define ORION5X_TIMER_BASE (ORION5X_REGISTER(0x20300))
>>>> -#define ORION5X_REG_PCI_BASE (ORION5X_REGISTER(0x30000))
>>>> -#define ORION5X_REG_PCIE_BASE (ORION5X_REGISTER(0x40000))
>>>> -#define ORION5X_USB20_PORT0_BASE (ORION5X_REGISTER(0x50000))
>>>> -#define ORION5X_USB20_PORT1_BASE (ORION5X_REGISTER(0xA0000))
>>>> -#define ORION5X_EGIGA_BASE (ORION5X_REGISTER(0x72000))
>>>> -#define ORION5X_SATA_BASE (ORION5X_REGISTER(0x80000))
>>>> -#define ORION5X_SATA_PORT0_OFFSET 0x2000
>>>> -#define ORION5X_SATA_PORT1_OFFSET 0x4000
>>>> -
>>>> -/* Orion5x GbE controller has a single port */
>>>> -#define MAX_MVGBE_DEVS 1
>>>> -#define MVGBE0_BASE ORION5X_EGIGA_BASE
>>>> -
>>>> -/* Orion5x USB Host controller is port 1 */
>>>> -#define MVUSB0_BASE ORION5X_USB20_HOST_PORT_BASE
>>>> -#define MVUSB0_CPU_ATTR_DRAM_CS0 ORION5X_ATTR_DRAM_CS0
>>>> -#define MVUSB0_CPU_ATTR_DRAM_CS1 ORION5X_ATTR_DRAM_CS1
>>>> -#define MVUSB0_CPU_ATTR_DRAM_CS2 ORION5X_ATTR_DRAM_CS2
>>>> -#define MVUSB0_CPU_ATTR_DRAM_CS3 ORION5X_ATTR_DRAM_CS3
>>>> -
>>>> -/* Kirkwood CPU memory windows */
>>>> -#define MVCPU_WIN_CTRL_DATA ORION5X_CPU_WIN_CTRL_DATA
>>>> -#define MVCPU_WIN_ENABLE ORION5X_WIN_ENABLE
>>>> -#define MVCPU_WIN_DISABLE ORION5X_WIN_DISABLE
>>>> -
>>>> -#define CONFIG_MAX_RAM_BANK_SIZE (64*1024*1024)
>>>> -
>>>> -/* include here SoC variants. 5181, 5281, 6183 should go here when
>>>> - adding support for them, and this comment should then be updated. */
>>>> -#if defined(CONFIG_88F5182)
>>>> -#include <asm/arch/mv88f5182.h>
>>>> -#else
>>>> -#error "SOC Name not defined"
>>>> -#endif
>>>> -#endif /* CONFIG_FEROCEON */
>>>> -#endif /* _ASM_ARCH_ORION5X_H */
>>>> diff --git a/arch/arm/mach-orion5x/lowlevel_init.S
>>>> b/arch/arm/mach-orion5x/lowlevel_init.S
>>>> deleted file mode 100644
>>>> index aa3fcf7c3010..000000000000
>>>> --- a/arch/arm/mach-orion5x/lowlevel_init.S
>>>> +++ /dev/null
>>>> @@ -1,286 +0,0 @@
>>>> -/* SPDX-License-Identifier: GPL-2.0+ */
>>>> -/*
>>>> - * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot at aribaud.net>
>>>> - *
>>>> - * (C) Copyright 2009
>>>> - * Marvell Semiconductor <www.marvell.com>
>>>> - * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
>>>> - */
>>>> -
>>>> -#include <config.h>
>>>> -#include "asm/arch/orion5x.h"
>>>> -
>>>> -/*
>>>> - * Configuration values for SDRAM access setup
>>>> - */
>>>> -
>>>> -#define SDRAM_CONFIG 0x3148400
>>>> -#define SDRAM_MODE 0x62
>>>> -#define SDRAM_CONTROL 0x4041000
>>>> -#define SDRAM_TIME_CTRL_LOW 0x11602220
>>>> -#define SDRAM_TIME_CTRL_HI 0x40c
>>>> -#define SDRAM_OPEN_PAGE_EN 0x0
>>>> -/* DDR 1 2x 32M NANYA NT5DS16M16CS-6K ==> 64MB */
>>>> -#define SDRAM_BANK0_SIZE 0x3ff0001
>>>> -#define SDRAM_ADDR_CTRL 0x10
>>>> -
>>>> -#define SDRAM_OP_NOP 0x05
>>>> -#define SDRAM_OP_SETMODE 0x03
>>>> -
>>>> -#define SDRAM_PAD_CTRL_WR_EN 0x80000000
>>>> -#define SDRAM_PAD_CTRL_TUNE_EN 0x00010000
>>>> -#define SDRAM_PAD_CTRL_DRVN_MASK 0x0000003f
>>>> -#define SDRAM_PAD_CTRL_DRVP_MASK 0x00000fc0
>>>> -
>>>> -/*
>>>> - * For Guideline MEM-3 - Drive Strength value
>>>> - */
>>>> -
>>>> -#define DDR1_PAD_STRENGTH_DEFAULT 0x00001000
>>>> -#define SDRAM_PAD_CTRL_DRV_STR_MASK 0x00003000
>>>> -
>>>> -/*
>>>> - * For Guideline MEM-4 - DQS Reference Delay Tuning
>>>> - */
>>>> -
>>>> -#define MSAR_ARMDDRCLCK_MASK 0x000000f0
>>>> -#define MSAR_ARMDDRCLCK_H_MASK 0x00000100
>>>> -
>>>> -#define MSAR_ARMDDRCLCK_333_167 0x00000000
>>>> -#define MSAR_ARMDDRCLCK_500_167 0x00000030
>>>> -#define MSAR_ARMDDRCLCK_667_167 0x00000060
>>>> -#define MSAR_ARMDDRCLCK_400_200_1 0x000001E0
>>>> -#define MSAR_ARMDDRCLCK_400_200 0x00000010
>>>> -#define MSAR_ARMDDRCLCK_600_200 0x00000050
>>>> -#define MSAR_ARMDDRCLCK_800_200 0x00000070
>>>> -
>>>> -#define FTDLL_DDR1_166MHZ 0x0047F001
>>>> -
>>>> -#define FTDLL_DDR1_200MHZ 0x0044D001
>>>> -
>>>> -/*
>>>> - * Low-level init happens right after start.S has switched to SVC32,
>>>> - * flushed and disabled caches and disabled MMU. We're still running
>>>> - * from the boot chip select, so the first thing SPL should do is to
>>>> - * set up the RAM to copy U-Boot into.
>>>> - */
>>>> -
>>>> -.globl lowlevel_init
>>>> -
>>>> -lowlevel_init:
>>>> -
>>>> -#ifdef CONFIG_SPL_BUILD
>>>> -
>>>> - /* Use 'r2 as the base for internal register accesses */
>>>> - ldr r2, =ORION5X_REGS_PHY_BASE
>>>> -
>>>> - /* move internal registers from the default 0xD0000000
>>>> - * to their intended location, defined by SoC */
>>>> - ldr r3, =0xD0000000
>>>> - add r3, r3, #0x20000
>>>> - str r2, [r3, #0x80]
>>>> -
>>>> - /* Use R3 as the base for DRAM registers */
>>>> - add r3, r2, #0x01000
>>>> -
>>>> - /*DDR SDRAM Initialization Control */
>>>> - ldr r0, =0x00000001
>>>> - str r0, [r3, #0x480]
>>>> -
>>>> - /* Use R3 as the base for PCI registers */
>>>> - add r3, r2, #0x31000
>>>> -
>>>> - /* Disable arbiter */
>>>> - ldr r0, =0x00000030
>>>> - str r0, [r3, #0xd00]
>>>> -
>>>> - /* Use R3 as the base for DRAM registers */
>>>> - add r3, r2, #0x01000
>>>> -
>>>> - /* set all dram windows to 0 */
>>>> - mov r0, #0
>>>> - str r0, [r3, #0x504]
>>>> - str r0, [r3, #0x50C]
>>>> - str r0, [r3, #0x514]
>>>> - str r0, [r3, #0x51C]
>>>> -
>>>> - /* 1) Configure SDRAM */
>>>> - ldr r0, =SDRAM_CONFIG
>>>> - str r0, [r3, #0x400]
>>>> -
>>>> - /* 2) Set SDRAM Control reg */
>>>> - ldr r0, =SDRAM_CONTROL
>>>> - str r0, [r3, #0x404]
>>>> -
>>>> - /* 3) Write SDRAM address control register */
>>>> - ldr r0, =SDRAM_ADDR_CTRL
>>>> - str r0, [r3, #0x410]
>>>> -
>>>> - /* 4) Write SDRAM bank 0 size register */
>>>> - ldr r0, =SDRAM_BANK0_SIZE
>>>> - str r0, [r3, #0x504]
>>>> - /* keep other banks disabled */
>>>> -
>>>> - /* 5) Write SDRAM open pages control register */
>>>> - ldr r0, =SDRAM_OPEN_PAGE_EN
>>>> - str r0, [r3, #0x414]
>>>> -
>>>> - /* 6) Write SDRAM timing Low register */
>>>> - ldr r0, =SDRAM_TIME_CTRL_LOW
>>>> - str r0, [r3, #0x408]
>>>> -
>>>> - /* 7) Write SDRAM timing High register */
>>>> - ldr r0, =SDRAM_TIME_CTRL_HI
>>>> - str r0, [r3, #0x40C]
>>>> -
>>>> - /* 8) Write SDRAM mode register */
>>>> - /* The CPU must not attempt to change the SDRAM Mode register
>>>> setting */
>>>> - /* prior to DRAM controller completion of the DRAM
>>>> initialization */
>>>> - /* sequence. To guarantee this restriction, it is recommended
>>>> that */
>>>> - /* the CPU sets the SDRAM Operation register to NOP command,
>>>> performs */
>>>> - /* read polling until the register is back in Normal operation
>>>> value, */
>>>> - /* and then sets SDRAM Mode register to its new
>>>> value. */
>>>> -
>>>> - /* 8.1 write 'nop' to SDRAM operation */
>>>> - ldr r0, =SDRAM_OP_NOP
>>>> - str r0, [r3, #0x418]
>>>> -
>>>> - /* 8.2 poll SDRAM operation until back in 'normal' mode. */
>>>> -1:
>>>> - ldr r0, [r3, #0x418]
>>>> - cmp r0, #0
>>>> - bne 1b
>>>> -
>>>> - /* 8.3 Now its safe to write new value to SDRAM Mode
>>>> register */
>>>> - ldr r0, =SDRAM_MODE
>>>> - str r0, [r3, #0x41C]
>>>> -
>>>> - /* 8.4 Set new mode */
>>>> - ldr r0, =SDRAM_OP_SETMODE
>>>> - str r0, [r3, #0x418]
>>>> -
>>>> - /* 8.5 poll SDRAM operation until back in 'normal' mode. */
>>>> -2:
>>>> - ldr r0, [r3, #0x418]
>>>> - cmp r0, #0
>>>> - bne 2b
>>>> -
>>>> - /* DDR SDRAM Address/Control Pads Calibration */
>>>> - ldr r0, [r3, #0x4C0]
>>>> -
>>>> - /* Set Bit [31] to make the register writable */
>>>> - orr r0, r0, #SDRAM_PAD_CTRL_WR_EN
>>>> - str r0, [r3, #0x4C0]
>>>> -
>>>> - bic r0, r0, #SDRAM_PAD_CTRL_WR_EN
>>>> - bic r0, r0, #SDRAM_PAD_CTRL_TUNE_EN
>>>> - bic r0, r0, #SDRAM_PAD_CTRL_DRVN_MASK
>>>> - bic r0, r0, #SDRAM_PAD_CTRL_DRVP_MASK
>>>> -
>>>> - /* Get the final N locked value of driving strength [22:17] */
>>>> - mov r1, r0
>>>> - mov r1, r1, LSL #9
>>>> - mov r1, r1, LSR #26 /* r1[5:0]<DrvN> =
>>>> r3[22:17]<LockN> */
>>>> - orr r1, r1, r1, LSL #6 /* r1[11:6]<DrvP> = r1[5:0]<DrvN> */
>>>> -
>>>> - /* Write to both <DrvN> bits [5:0] and <DrvP> bits [11:6] */
>>>> - orr r0, r0, r1
>>>> - str r0, [r3, #0x4C0]
>>>> -
>>>> - /* DDR SDRAM Data Pads Calibration */
>>>> - ldr r0, [r3, #0x4C4]
>>>> -
>>>> - /* Set Bit [31] to make the register writable */
>>>> - orr r0, r0, #SDRAM_PAD_CTRL_WR_EN
>>>> - str r0, [r3, #0x4C4]
>>>> -
>>>> - bic r0, r0, #SDRAM_PAD_CTRL_WR_EN
>>>> - bic r0, r0, #SDRAM_PAD_CTRL_TUNE_EN
>>>> - bic r0, r0, #SDRAM_PAD_CTRL_DRVN_MASK
>>>> - bic r0, r0, #SDRAM_PAD_CTRL_DRVP_MASK
>>>> -
>>>> - /* Get the final N locked value of driving strength [22:17] */
>>>> - mov r1, r0
>>>> - mov r1, r1, LSL #9
>>>> - mov r1, r1, LSR #26
>>>> - orr r1, r1, r1, LSL #6 /* r1[5:0] = r3[22:17]<LockN> */
>>>> -
>>>> - /* Write to both <DrvN> bits [5:0] and <DrvP> bits [11:6] */
>>>> - orr r0, r0, r1
>>>> -
>>>> - str r0, [r3, #0x4C4]
>>>> -
>>>> - /* Implement Guideline (GL# MEM-3) Drive Strength Value */
>>>> - /* Relevant for: 88F5181-A1/B0/B1 and 88F5281-A0/B0 */
>>>> -
>>>> - ldr r1, =DDR1_PAD_STRENGTH_DEFAULT
>>>> -
>>>> - /* Enable writes to DDR SDRAM Addr/Ctrl Pads Calibration
>>>> register */
>>>> - ldr r0, [r3, #0x4C0]
>>>> - orr r0, r0, #SDRAM_PAD_CTRL_WR_EN
>>>> - str r0, [r3, #0x4C0]
>>>> -
>>>> - /* Correct strength and disable writes again */
>>>> - bic r0, r0, #SDRAM_PAD_CTRL_WR_EN
>>>> - bic r0, r0, #SDRAM_PAD_CTRL_DRV_STR_MASK
>>>> - orr r0, r0, r1
>>>> - str r0, [r3, #0x4C0]
>>>> -
>>>> - /* Enable writes to DDR SDRAM Data Pads Calibration register */
>>>> - ldr r0, [r3, #0x4C4]
>>>> - orr r0, r0, #SDRAM_PAD_CTRL_WR_EN
>>>> - str r0, [r3, #0x4C4]
>>>> -
>>>> - /* Correct strength and disable writes again */
>>>> - bic r0, r0, #SDRAM_PAD_CTRL_DRV_STR_MASK
>>>> - bic r0, r0, #SDRAM_PAD_CTRL_WR_EN
>>>> - orr r0, r0, r1
>>>> - str r0, [r3, #0x4C4]
>>>> -
>>>> - /* Implement Guideline (GL# MEM-4) DQS Reference Delay Tuning */
>>>> - /* Relevant for: 88F5181-A1/B0/B1 and 88F5281-A0/B0 */
>>>> -
>>>> - /* Get the "sample on reset" register for the DDR frequancy */
>>>> - ldr r3, =0x10000
>>>> - ldr r0, [r3, #0x010]
>>>> - ldr r1, =MSAR_ARMDDRCLCK_MASK
>>>> - and r1, r0, r1
>>>> -
>>>> - ldr r0, =FTDLL_DDR1_166MHZ
>>>> - cmp r1, #MSAR_ARMDDRCLCK_333_167
>>>> - beq 3f
>>>> - cmp r1, #MSAR_ARMDDRCLCK_500_167
>>>> - beq 3f
>>>> - cmp r1, #MSAR_ARMDDRCLCK_667_167
>>>> - beq 3f
>>>> -
>>>> - ldr r0, =FTDLL_DDR1_200MHZ
>>>> - cmp r1, #MSAR_ARMDDRCLCK_400_200_1
>>>> - beq 3f
>>>> - cmp r1, #MSAR_ARMDDRCLCK_400_200
>>>> - beq 3f
>>>> - cmp r1, #MSAR_ARMDDRCLCK_600_200
>>>> - beq 3f
>>>> - cmp r1, #MSAR_ARMDDRCLCK_800_200
>>>> - beq 3f
>>>> -
>>>> - ldr r0, =0
>>>> -
>>>> -3:
>>>> - /* Use R3 as the base for DRAM registers */
>>>> - add r3, r2, #0x01000
>>>> -
>>>> - ldr r2, [r3, #0x484]
>>>> - orr r2, r2, r0
>>>> - str r2, [r3, #0x484]
>>>> -
>>>> - /* enable for 2 GB DDR; detection should find out real amount */
>>>> - sub r0, r0, r0
>>>> - str r0, [r3, #0x500]
>>>> - ldr r0, =0x7fff0001
>>>> - str r0, [r3, #0x504]
>>>> -
>>>> -#endif /* CONFIG_SPL_BUILD */
>>>> -
>>>> - /* Return to U-Boot via saved link register */
>>>> - mov pc, lr
>>>> diff --git a/arch/arm/mach-orion5x/timer.c
>>>> b/arch/arm/mach-orion5x/timer.c
>>>> deleted file mode 100644
>>>> index d7ea2e3943fc..000000000000
>>>> --- a/arch/arm/mach-orion5x/timer.c
>>>> +++ /dev/null
>>>> @@ -1,174 +0,0 @@
>>>> -// SPDX-License-Identifier: GPL-2.0+
>>>> -/*
>>>> - * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot at aribaud.net>
>>>> - *
>>>> - * Based on original Kirkwood support which is
>>>> - * Copyright (C) Marvell International Ltd. and its affiliates
>>>> - * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
>>>> - */
>>>> -
>>>> -#include <common.h>
>>>> -#include <init.h>
>>>> -#include <time.h>
>>>> -#include <asm/global_data.h>
>>>> -#include <asm/io.h>
>>>> -#include <linux/delay.h>
>>>> -
>>>> -#define UBOOT_CNTR 0 /* counter to use for uboot timer */
>>>> -
>>>> -/* Timer reload and current value registers */
>>>> -struct orion5x_tmr_val {
>>>> - u32 reload; /* Timer reload reg */
>>>> - u32 val; /* Timer value reg */
>>>> -};
>>>> -
>>>> -/* Timer registers */
>>>> -struct orion5x_tmr_registers {
>>>> - u32 ctrl; /* Timer control reg */
>>>> - u32 pad[3];
>>>> - struct orion5x_tmr_val tmr[2];
>>>> - u32 wdt_reload;
>>>> - u32 wdt_val;
>>>> -};
>>>> -
>>>> -struct orion5x_tmr_registers *orion5x_tmr_regs =
>>>> - (struct orion5x_tmr_registers *)ORION5X_TIMER_BASE;
>>>> -
>>>> -/*
>>>> - * ARM Timers Registers Map
>>>> - */
>>>> -#define CNTMR_CTRL_REG (&orion5x_tmr_regs->ctrl)
>>>> -#define CNTMR_RELOAD_REG(tmrnum)
>>>> (&orion5x_tmr_regs->tmr[tmrnum].reload)
>>>> -#define CNTMR_VAL_REG(tmrnum)
>>>> (&orion5x_tmr_regs->tmr[tmrnum].val)
>>>> -
>>>> -/*
>>>> - * ARM Timers Control Register
>>>> - * CPU_TIMERS_CTRL_REG (CTCR)
>>>> - */
>>>> -#define CTCR_ARM_TIMER_EN_OFFS(cntr) (cntr * 2)
>>>> -#define CTCR_ARM_TIMER_EN_MASK(cntr) (1 << CTCR_ARM_TIMER_EN_OFFS)
>>>> -#define CTCR_ARM_TIMER_EN(cntr) (1 <<
>>>> CTCR_ARM_TIMER_EN_OFFS(cntr))
>>>> -#define CTCR_ARM_TIMER_DIS(cntr) (0 << CTCR_ARM_TIMER_EN_OFFS(cntr))
>>>> -
>>>> -#define CTCR_ARM_TIMER_AUTO_OFFS(cntr) ((cntr * 2) + 1)
>>>> -#define CTCR_ARM_TIMER_AUTO_MASK(cntr) (1 << 1)
>>>> -#define CTCR_ARM_TIMER_AUTO_EN(cntr) (1 <<
>>>> CTCR_ARM_TIMER_AUTO_OFFS(cntr))
>>>> -#define CTCR_ARM_TIMER_AUTO_DIS(cntr) (0 <<
>>>> CTCR_ARM_TIMER_AUTO_OFFS(cntr))
>>>> -
>>>> -/*
>>>> - * ARM Timer\Watchdog Reload Register
>>>> - * CNTMR_RELOAD_REG (TRR)
>>>> - */
>>>> -#define TRG_ARM_TIMER_REL_OFFS 0
>>>> -#define TRG_ARM_TIMER_REL_MASK 0xffffffff
>>>> -
>>>> -/*
>>>> - * ARM Timer\Watchdog Register
>>>> - * CNTMR_VAL_REG (TVRG)
>>>> - */
>>>> -#define TVR_ARM_TIMER_OFFS 0
>>>> -#define TVR_ARM_TIMER_MASK 0xffffffff
>>>> -#define TVR_ARM_TIMER_MAX 0xffffffff
>>>> -#define TIMER_LOAD_VAL 0xffffffff
>>>> -
>>>> -static inline ulong read_timer(void)
>>>> -{
>>>> - return readl(CNTMR_VAL_REG(UBOOT_CNTR))
>>>> - / (CONFIG_SYS_TCLK / 1000);
>>>> -}
>>>> -
>>>> -DECLARE_GLOBAL_DATA_PTR;
>>>> -
>>>> -#define timestamp gd->arch.tbl
>>>> -#define lastdec gd->arch.lastinc
>>>> -
>>>> -static ulong get_timer_masked(void)
>>>> -{
>>>> - ulong now = read_timer();
>>>> -
>>>> - if (lastdec >= now) {
>>>> - /* normal mode */
>>>> - timestamp += lastdec - now;
>>>> - } else {
>>>> - /* we have an overflow ... */
>>>> - timestamp += lastdec +
>>>> - (TIMER_LOAD_VAL / (CONFIG_SYS_TCLK / 1000)) - now;
>>>> - }
>>>> - lastdec = now;
>>>> -
>>>> - return timestamp;
>>>> -}
>>>> -
>>>> -ulong get_timer(ulong base)
>>>> -{
>>>> - return get_timer_masked() - base;
>>>> -}
>>>> -
>>>> -static inline ulong uboot_cntr_val(void)
>>>> -{
>>>> - return readl(CNTMR_VAL_REG(UBOOT_CNTR));
>>>> -}
>>>> -
>>>> -void __udelay(unsigned long usec)
>>>> -{
>>>> - uint current;
>>>> - ulong delayticks;
>>>> -
>>>> - current = uboot_cntr_val();
>>>> - delayticks = (usec * (CONFIG_SYS_TCLK / 1000000));
>>>> -
>>>> - if (current < delayticks) {
>>>> - delayticks -= current;
>>>> - while (uboot_cntr_val() < current)
>>>> - ;
>>>> - while ((TIMER_LOAD_VAL - delayticks) < uboot_cntr_val())
>>>> - ;
>>>> - } else {
>>>> - while (uboot_cntr_val() > (current - delayticks))
>>>> - ;
>>>> - }
>>>> -}
>>>> -
>>>> -/*
>>>> - * init the counter
>>>> - */
>>>> -int timer_init(void)
>>>> -{
>>>> - unsigned int cntmrctrl;
>>>> -
>>>> - /* load value into timer */
>>>> - writel(TIMER_LOAD_VAL, CNTMR_RELOAD_REG(UBOOT_CNTR));
>>>> - writel(TIMER_LOAD_VAL, CNTMR_VAL_REG(UBOOT_CNTR));
>>>> -
>>>> - /* enable timer in auto reload mode */
>>>> - cntmrctrl = readl(CNTMR_CTRL_REG);
>>>> - cntmrctrl |= CTCR_ARM_TIMER_EN(UBOOT_CNTR);
>>>> - cntmrctrl |= CTCR_ARM_TIMER_AUTO_EN(UBOOT_CNTR);
>>>> - writel(cntmrctrl, CNTMR_CTRL_REG);
>>>> - return 0;
>>>> -}
>>>> -
>>>> -void timer_init_r(void)
>>>> -{
>>>> - /* init the timestamp and lastdec value */
>>>> - lastdec = read_timer();
>>>> - timestamp = 0;
>>>> -}
>>>> -
>>>> -/*
>>>> - * This function is derived from PowerPC code (read timebase as long
>>>> long).
>>>> - * On ARM it just returns the timer value.
>>>> - */
>>>> -unsigned long long get_ticks(void)
>>>> -{
>>>> - return get_timer(0);
>>>> -}
>>>> -
>>>> -/*
>>>> - * This function is derived from PowerPC code (timebase clock
>>>> frequency).
>>>> - * On ARM it returns the number of timer ticks per second.
>>>> - */
>>>> -ulong get_tbclk(void)
>>>> -{
>>>> - return (ulong)CONFIG_SYS_HZ;
>>>> -}
>>>> diff --git a/arch/arm/mach-orion5x/u-boot-spl.lds
>>>> b/arch/arm/mach-orion5x/u-boot-spl.lds
>>>> deleted file mode 100644
>>>> index 154bb1206035..000000000000
>>>> --- a/arch/arm/mach-orion5x/u-boot-spl.lds
>>>> +++ /dev/null
>>>> @@ -1,60 +0,0 @@
>>>> -/* SPDX-License-Identifier: GPL-2.0+ */
>>>> -/*
>>>> - * (C) Copyright 2014 Albert ARIBAUD <albert.u.boot at aribaud.net>
>>>> - *
>>>> - * Based on:
>>>> - *
>>>> - * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
>>>> - * Tom Cubie <tangliang at allwinnertech.com>
>>>> - *
>>>> - * Based on omap-common/u-boot-spl.lds:
>>>> - *
>>>> - * (C) Copyright 2002
>>>> - * Gary Jennejohn, DENX Software Engineering, <garyj at denx.de>
>>>> - *
>>>> - * (C) Copyright 2010
>>>> - * Texas Instruments, <www.ti.com>
>>>> - * Aneesh V <aneesh at ti.com>
>>>> - */
>>>> -MEMORY { .nor : ORIGIN = IMAGE_TEXT_BASE,\
>>>> - LENGTH = IMAGE_MAX_SIZE }
>>>> -MEMORY { .bss : ORIGIN = CONFIG_SPL_BSS_START_ADDR, \
>>>> - LENGTH = CONFIG_SPL_BSS_MAX_SIZE }
>>>> -
>>>> -OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
>>>> -OUTPUT_ARCH(arm)
>>>> -ENTRY(_start)
>>>> -SECTIONS
>>>> -{
>>>> - .text :
>>>> - {
>>>> - __start = .;
>>>> - *(.vectors)
>>>> - CPUDIR/start.o (.text)
>>>> - *(.text*)
>>>> - } > .nor
>>>> -
>>>> - . = ALIGN(4);
>>>> - .rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } >.nor
>>>> -
>>>> - . = ALIGN(4);
>>>> - .data : { *(SORT_BY_ALIGNMENT(.data*)) } >.nor
>>>> -
>>>> - . = ALIGN(4);
>>>> - __u_boot_list : {
>>>> - KEEP(*(SORT(__u_boot_list*)));
>>>> - } > .nor
>>>> -
>>>> - . = ALIGN(4);
>>>> - __image_copy_end = .;
>>>> - _end = .;
>>>> -
>>>> - .bss :
>>>> - {
>>>> - . = ALIGN(4);
>>>> - __bss_start = .;
>>>> - *(.bss*)
>>>> - . = ALIGN(4);
>>>> - __bss_end = .;
>>>> - } > .bss
>>>> -}
>>>> diff --git a/drivers/i2c/mvtwsi.c b/drivers/i2c/mvtwsi.c
>>>> index f48a4f25aae6..b722089c3d58 100644
>>>> --- a/drivers/i2c/mvtwsi.c
>>>> +++ b/drivers/i2c/mvtwsi.c
>>>> @@ -30,9 +30,7 @@ DECLARE_GLOBAL_DATA_PTR;
>>>> */
>>>> #if !CONFIG_IS_ENABLED(DM_I2C)
>>>> -#if defined(CONFIG_ARCH_ORION5X)
>>>> -#include <asm/arch/orion5x.h>
>>>> -#elif (defined(CONFIG_ARCH_KIRKWOOD) || defined(CONFIG_ARCH_MVEBU))
>>>> +#if (defined(CONFIG_ARCH_KIRKWOOD) || defined(CONFIG_ARCH_MVEBU))
>>>> #include <asm/arch/soc.h>
>>>> #elif defined(CONFIG_ARCH_SUNXI)
>>>> #include <asm/arch/i2c.h>
>>>> diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
>>>> index 6bbbadc5eef3..89fd2d1db737 100644
>>>> --- a/drivers/net/Kconfig
>>>> +++ b/drivers/net/Kconfig
>>>> @@ -440,7 +440,7 @@ config KSZ9477
>>>> config MVGBE
>>>> bool "Marvell Orion5x/Kirkwood network interface support"
>>>> - depends on ARCH_KIRKWOOD || ARCH_ORION5X
>>>> + depends on ARCH_KIRKWOOD
>>>> select PHYLIB
>>>> help
>>>> This driver supports the network interface units in the
>>>> diff --git a/drivers/net/mvgbe.c b/drivers/net/mvgbe.c
>>>> index a77c05743262..c96732786d6c 100644
>>>> --- a/drivers/net/mvgbe.c
>>>> +++ b/drivers/net/mvgbe.c
>>>> @@ -29,8 +29,6 @@
>>>> #if defined(CONFIG_ARCH_KIRKWOOD)
>>>> #include <asm/arch/soc.h>
>>>> -#elif defined(CONFIG_ARCH_ORION5X)
>>>> -#include <asm/arch/orion5x.h>
>>>> #endif
>>>> #include "mvgbe.h"
>>>> diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
>>>> index a0f48f09a7f3..3a7cfd8043c8 100644
>>>> --- a/drivers/usb/host/Kconfig
>>>> +++ b/drivers/usb/host/Kconfig
>>>> @@ -175,7 +175,7 @@ config USB_EHCI_EXYNOS
>>>> config USB_EHCI_MARVELL
>>>> bool "Support for Marvell on-chip EHCI USB controller"
>>>> - depends on ARCH_MVEBU || ARCH_KIRKWOOD || ARCH_ORION5X
>>>> + depends on ARCH_MVEBU || ARCH_KIRKWOOD
>>>> default y
>>>> select USB_EHCI_IS_TDI if !ARM64
>>>> ---help---
>>>> diff --git a/drivers/usb/host/ehci-marvell.c
>>>> b/drivers/usb/host/ehci-marvell.c
>>>> index b7e60c690a4f..e7cb2ee92a01 100644
>>>> --- a/drivers/usb/host/ehci-marvell.c
>>>> +++ b/drivers/usb/host/ehci-marvell.c
>>>> @@ -18,8 +18,6 @@
>>>> #if defined(CONFIG_ARCH_KIRKWOOD)
>>>> #include <asm/arch/soc.h>
>>>> -#elif defined(CONFIG_ARCH_ORION5X)
>>>> -#include <asm/arch/orion5x.h>
>>>> #endif
>>>> DECLARE_GLOBAL_DATA_PTR;
>>>> diff --git a/include/configs/mv-common.h b/include/configs/mv-common.h
>>>> index 384a8f7d1dd8..0d39add6b602 100644
>>>> --- a/include/configs/mv-common.h
>>>> +++ b/include/configs/mv-common.h
>>>> @@ -10,7 +10,6 @@
>>>> * This file should be included in board config header file.
>>>> *
>>>> * It supports common definations for Kirkwood platform
>>>> - * TBD: support for Orion5X platforms
>>>> */
>>>> #ifndef _MV_COMMON_H
>>>> --
>>>> 2.37.3
>>>>
>>
>> Viele Grüße,
>> Stefan Roese
>>
Viele Grüße,
Stefan Roese
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de
More information about the U-Boot
mailing list