[PATCH v2 02/12] rockchip: puma-rk3399: use gpio-hog instead of fixed-regulator for enabling eMMC/SPI-NOR

[Quentin Schulz]

From: Quentin Schulz <quentin.schulz at theobroma-systems.com>

On Haikou devkit, it is possible to disable eMMC and SPI-NOR to force
booting from SD card or USB via rkdeveloptool by toggling a switch. This
switch needs to be overridden in software to be able to access eMMC and
SPI-NOR once the device has booted from SD Card. Puma SoM can override
this pin via gpio3_d5.

Until now, fixed regulator device was abused to model this, but since
there's now support for GPIO hogs, let's use it.

Since we want to be able to boot the SPL from SD Card but give it the
ability to load U-Boot proper from a fallback medium such as eMMC and
SPI-NOR, SPL support for GPIO hogs needs to be enabled too. Support for
other kinds of regulators are not needed anymore, so let's disable them.

Cc: Quentin Schulz <foss+uboot at 0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz at theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang at rock-chips.com>
---
 arch/arm/dts/rk3399-puma-haikou-u-boot.dtsi | 32 +++++++++------------
 configs/puma-rk3399_defconfig               |  5 ++--
 2 files changed, 16 insertions(+), 21 deletions(-)

diff --git a/arch/arm/dts/rk3399-puma-haikou-u-boot.dtsi b/arch/arm/dts/rk3399-puma-haikou-u-boot.dtsi
index e0476ab25c..b9b6ac3f6c 100644
--- a/arch/arm/dts/rk3399-puma-haikou-u-boot.dtsi
+++ b/arch/arm/dts/rk3399-puma-haikou-u-boot.dtsi
@@ -31,24 +31,6 @@
 		spi5 = &spi5;
 	};
 
-	/*
-	 * The Qseven BIOS_DISABLE signal on the RK3399-Q7 keeps the on-module
-	 * eMMC and SPI flash powered-down initially (in fact it keeps the
-	 * reset signal asserted).  Even though it is an enable signal, we
-	 * model this as a regulator.
-	 */
-	bios_enable: bios_enable {
-		compatible = "regulator-fixed";
-		u-boot,dm-pre-reloc;
-		regulator-name = "bios_enable";
-		enable-active-high;
-		gpio = <&gpio3 RK_PD5 GPIO_ACTIVE_LOW>;
-		regulator-always-on;
-		regulator-boot-on;
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
 	vdd_log: vdd-log {
 		compatible = "pwm-regulator";
 		pwms = <&pwm2 0 25000 1>;
@@ -68,6 +50,20 @@
 
 &gpio3 {
 	u-boot,dm-pre-reloc;
+
+	/*
+	 * The Qseven BIOS_DISABLE signal on the RK3399-Q7 keeps the on-module
+	 * eMMC and SPI flash powered-down initially (in fact it keeps the
+	 * reset signal asserted). BIOS_DISABLE_OVERRIDE pin allows to re-enable
+	 * eMMC and SPI after the SPL has been booted from SD Card.
+	 */
+	bios_disable_override {
+		u-boot,dm-pre-reloc;
+		gpios = <RK_PD5 GPIO_ACTIVE_LOW>;
+		output-high;
+		line-name = "bios_disable_override";
+		gpio-hog;
+	};
 };
 
 &norflash {
diff --git a/configs/puma-rk3399_defconfig b/configs/puma-rk3399_defconfig
index 6acc442ba8..6082b67523 100644
--- a/configs/puma-rk3399_defconfig
+++ b/configs/puma-rk3399_defconfig
@@ -58,6 +58,8 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_SYS_MMC_ENV_DEV=1
 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
 CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_GPIO_HOG=y
+CONFIG_SPL_GPIO_HOG=y
 CONFIG_ROCKCHIP_GPIO=y
 CONFIG_SYS_I2C_ROCKCHIP=y
 CONFIG_MISC=y
@@ -80,10 +82,7 @@ CONFIG_PHY_ROCKCHIP_TYPEC=y
 CONFIG_DM_PMIC_FAN53555=y
 CONFIG_PMIC_RK8XX=y
 CONFIG_SPL_PMIC_RK8XX=y
-CONFIG_SPL_DM_REGULATOR=y
 CONFIG_REGULATOR_PWM=y
-CONFIG_SPL_DM_REGULATOR_FIXED=y
-CONFIG_DM_REGULATOR_GPIO=y
 CONFIG_REGULATOR_RK8XX=y
 CONFIG_PWM_ROCKCHIP=y
 CONFIG_DM_RESET=y
-- 
2.37.3