[PATCH v2 5/8] fpga: ACEX1K: Use logging feature instead of FPGA_DEBUG

Alexander Dahl ada at thorsis.com
Wed Sep 21 15:22:13 CEST 2022


Instead of using DEBUG or LOG_DEBUG the driver still had its own
definition for debug output.

Signed-off-by: Alexander Dahl <ada at thorsis.com>
---
 drivers/fpga/ACEX1K.c | 22 +++++++++-------------
 1 file changed, 9 insertions(+), 13 deletions(-)

diff --git a/drivers/fpga/ACEX1K.c b/drivers/fpga/ACEX1K.c
index aca8049c56..3877aedb1d 100644
--- a/drivers/fpga/ACEX1K.c
+++ b/drivers/fpga/ACEX1K.c
@@ -7,18 +7,14 @@
  * Rich Ireland, Enterasys Networks, rireland at enterasys.com.
  */
 
+#define LOG_CATEGORY UCLASS_FPGA
+
 #include <common.h>		/* core U-Boot definitions */
 #include <console.h>
+#include <log.h>
 #include <ACEX1K.h>		/* ACEX device family */
 #include <linux/delay.h>
 
-/* Define FPGA_DEBUG to get debug printf's */
-#ifdef	FPGA_DEBUG
-#define PRINTF(fmt,args...)	printf (fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-
 /* Note: The assumption is that we cannot possibly run fast enough to
  * overrun the device (the Slave Parallel mode can free run at 50MHz).
  * If there is a need to operate slower, define CONFIG_FPGA_DELAY in
@@ -44,7 +40,7 @@ int ACEX1K_load(Altera_desc *desc, const void *buf, size_t bsize)
 
 	switch (desc->iface) {
 	case passive_serial:
-		PRINTF ("%s: Launching Passive Serial Loader\n", __FUNCTION__);
+		log_debug("%s: Launching Passive Serial Loader\n", __func__);
 		ret_val = ACEX1K_ps_load (desc, buf, bsize);
 		break;
 
@@ -64,7 +60,7 @@ int ACEX1K_dump(Altera_desc *desc, const void *buf, size_t bsize)
 
 	switch (desc->iface) {
 	case passive_serial:
-		PRINTF ("%s: Launching Passive Serial Dump\n", __FUNCTION__);
+		log_debug("%s: Launching Passive Serial Dump\n", __func__);
 		ret_val = ACEX1K_ps_dump (desc, buf, bsize);
 		break;
 
@@ -93,8 +89,8 @@ static int ACEX1K_ps_load(Altera_desc *desc, const void *buf, size_t bsize)
 	Altera_ACEX1K_Passive_Serial_fns *fn = desc->iface_fns;
 	int i;
 
-	PRINTF ("%s: start with interface functions @ 0x%p\n",
-			__FUNCTION__, fn);
+	log_debug("%s: start with interface functions @ 0x%p\n",
+		  __func__, fn);
 
 	if (fn) {
 		size_t bytecount = 0;
@@ -102,7 +98,7 @@ static int ACEX1K_ps_load(Altera_desc *desc, const void *buf, size_t bsize)
 		int cookie = desc->cookie;	/* make a local copy */
 		unsigned long ts;		/* timestamp */
 
-		PRINTF ("%s: Function Table:\n"
+		log_debug("%s: Function Table:\n"
 				"ptr:\t0x%p\n"
 				"struct: 0x%p\n"
 				"config:\t0x%p\n"
@@ -110,7 +106,7 @@ static int ACEX1K_ps_load(Altera_desc *desc, const void *buf, size_t bsize)
 				"clk:\t0x%p\n"
 				"data:\t0x%p\n"
 				"done:\t0x%p\n\n",
-				__FUNCTION__, &fn, fn, fn->config, fn->status,
+				__func__, &fn, fn, fn->config, fn->status,
 				fn->clk, fn->data, fn->done);
 #ifdef CONFIG_SYS_FPGA_PROG_FEEDBACK
 		printf ("Loading FPGA Device %d...", cookie);
-- 
2.30.2



More information about the U-Boot mailing list