[PATCH v10 02/15] FWU: Add FWU metadata structure and driver for accessing metadata

[Jassi Brar]

On Tue, Sep 27, 2022 at 2:14 AM Sughosh Ganu <sughosh.ganu at linaro.org> wrote:
>
> On Mon, 26 Sept 2022 at 20:12, Jassi Brar <jassisinghbrar at gmail.com> wrote:
> >
> > On Mon, Sep 26, 2022 at 5:00 AM Sughosh Ganu <sughosh.ganu at linaro.org> wrote:
> > >
> > > On Mon, 26 Sept 2022 at 08:28, Jassi Brar <jassisinghbrar at gmail.com> wrote:
> > > >
> >
> > > >
> > > > .....
> > > > > +/**
> > > > > + * fwu_revert_boot_index() - Revert the active index in the FWU metadata
> > > > > + *
> > > > > + * Revert the active_index value in the FWU metadata, by swapping the values
> > > > > + * of active_index and previous_active_index in both copies of the
> > > > > + * FWU metadata.
> > > > > + *
> > > > > + * Return: 0 if OK, -ve on error
> > > > > + *
> > > > > + */
> > > > > +int fwu_revert_boot_index(void)
> > > > > +{
> > > > > +       int ret;
> > > > > +       u32 cur_active_index;
> > > > > +       struct udevice *dev;
> > > > > +       struct fwu_mdata mdata = { 0 };
> > > > > +
> > > > > +       ret = fwu_get_dev_mdata(&dev, &mdata);
> > > > > +       if (ret)
> > > > > +               return ret;
> > > > > +
> > > > > +       /*
> > > > > +        * Swap the active index and previous_active_index fields
> > > > > +        * in the FWU metadata
> > > > > +        */
> > > > > +       cur_active_index = mdata.active_index;
> > > > > +       mdata.active_index = mdata.previous_active_index;
> > > > > +       mdata.previous_active_index = cur_active_index;
> > > > >
> > > > This may cause problems.
> > > > We are reverting because active_index does not work, and here we set
> > > > it to previous_active_index which is supposed to mean "last good
> > > > index".
> > > >  Also this logic assumes a 2-banks setup, and is obviously incorrect
> > > > for >2 banks where the previous_active_index should point to
> > > > "boot_index minus 2" bank (but of course there is no guarantee that
> > > > that bank is preserved still).
> > > >  So either previous_active_index be left changed OR we also copy the
> > > > previous bank to active bank before the swap.
> > >
> > > Sorry, but I don't understand the review comment here. Even in the
> > > case of num_banks > 2, this function is simply using the
> > > previous_active_index value. It does not care what the
> > > previous_active_index value is. If you remember, the setting of the
> > > update bank is really a platform
> > > function(fwu_plat_get_update_index()). A platform can set any bank
> > > number as the update bank. So we cannot tell what the value of the
> > > previous_active_index will be.
> > >
> > Do you remember you pick update_bank in a circular-buffer manner in
> > fwu_plat_get_update_index() ? But don't even bother the >2 banks.
> >
> > Consider the simple 2-banks platform....
> > Initially:
> >        active_index = 1
> >        previous_active_index = 0
> >
> > After update and before reboot
> >        active_index = 0                  <<<< updated bank 0
> >        previous_active_index = 1
> >
> > After reboot, for some reason update fails (reject bank0) and we call
> > fwu_revert_boot_index()
> >        active_index = 1                    <<< good
> >        previous_active_index = 0    <<<< points to unbootable bank
> >
> > Which may be seen as inconsistency if we assume previous_bank to
> > always contain a bootable set of images.
> > So we also need to copy bank1 into bank0 as part of the revert (at
> > least as a backup for reasons other than a/b update failure).
>
> If the platform owner wants to restore a particular bank with good
> images, the procedure to update that bank needs to be followed just
> like it was any other update.
>
The banks are under FWU and the platform has (should have) no control
over which bank the image goes in.


> If an updated bank fails the image
> acceptance test, the following boot would be from the
> previous_active_bank. In that case, the other bank needs to be updated
> by explicitly putting capsules in the ESP and initiating the update.
>
Which capsule - the one that just failed or the previous one (which
may not be available/provided)?
Doesn't simply copying over the bank make more sense?

 >
> > > All that this function does is use the
> > > previous_active_index as the partition/bank to boot from in the
> > > subsequent boot cycle.
> > >
> > That is, you assume the previous_active_index bank contains working images.
>
> It is the responsibility of the platform owner to ensure that all
> partitions have valid images.
>
I differ. The platform should not be modifying banks and meta-data
beneath the fwu framework.
The specification says "A Client can only read from or write to images
in the update bank"

-j