[PATCH v2 10/28] ram: rockchip: rv1126: Control ddr init prints via DEBUG

[Kever Yang]

On 2022/8/18 22:52, Jagan Teki wrote:
> Control the ddr init print messages via RAM_ROCKCHIP_DEBUG
> instead of printing by default.
>
> This gives an option to configs to enable these prints or
> not.
>
> Signed-off-by: Jagan Teki <jagan at edgeble.ai>
Reviewed-by: Kever Yang <kever.yang at rock-chips.com>

Thanks,
- Kever
> ---
> Changes for v2:
> - none
>
>   drivers/ram/rockchip/sdram_rv1126.c | 38 +++++++++++++++++++----------
>   1 file changed, 25 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/ram/rockchip/sdram_rv1126.c b/drivers/ram/rockchip/sdram_rv1126.c
> index 9b1c34391e..6fe5b0305e 100644
> --- a/drivers/ram/rockchip/sdram_rv1126.c
> +++ b/drivers/ram/rockchip/sdram_rv1126.c
> @@ -3358,22 +3358,33 @@ static void ddr_set_rate_for_fsp(struct dram_info *dram,
>   	if (get_wrlvl_val(dram, sdram_params))
>   		printascii("get wrlvl value fail\n");
>   
> -	printascii("change to: ");
> -	printdec(f1);
> -	printascii("MHz\n");
> +	if (IS_ENABLED(CONFIG_RAM_ROCKCHIP_DEBUG)) {
> +		printascii("change to: ");
> +		printdec(f1);
> +		printascii("MHz\n");
> +	}
>   	ddr_set_rate(&dram_info, sdram_params, f1,
>   		     sdram_params->base.ddr_freq, 1, 1, 1);
> -	printascii("change to: ");
> -	printdec(f2);
> -	printascii("MHz\n");
> +
> +	if (IS_ENABLED(CONFIG_RAM_ROCKCHIP_DEBUG)) {
> +		printascii("change to: ");
> +		printdec(f2);
> +		printascii("MHz\n");
> +	}
>   	ddr_set_rate(&dram_info, sdram_params, f2, f1, 2, 0, 1);
> -	printascii("change to: ");
> -	printdec(f3);
> -	printascii("MHz\n");
> +
> +	if (IS_ENABLED(CONFIG_RAM_ROCKCHIP_DEBUG)) {
> +		printascii("change to: ");
> +		printdec(f3);
> +		printascii("MHz\n");
> +	}
>   	ddr_set_rate(&dram_info, sdram_params, f3, f2, 3, 1, 1);
> -	printascii("change to: ");
> -	printdec(f0);
> -	printascii("MHz(final freq)\n");
> +
> +	if (IS_ENABLED(CONFIG_RAM_ROCKCHIP_DEBUG)) {
> +		printascii("change to: ");
> +		printdec(f0);
> +		printascii("MHz(final freq)\n");
> +	}
>   	ddr_set_rate(&dram_info, sdram_params, f0, f3, 0, 0, 1);
>   }
>   
> @@ -3465,7 +3476,8 @@ static int rv1126_dmc_init(struct udevice *dev)
>   	save_rw_trn_result_to_ddr(&rw_trn_result);
>   #endif
>   
> -	printascii("out\n");
> +	if (IS_ENABLED(CONFIG_RAM_ROCKCHIP_DEBUG))
> +		printascii("out\n");
>   
>   	return ret;
>   error: