[PATCH v4 8/8] board: gw_ventana: enable MV88E61XX DSA support
Tim Harvey
tharvey at gateworks.com
Wed Sep 28 21:37:32 CEST 2022
Add MV88E61XX DSA support:
- update dt: U-Boot dsa driver requires different device-tree syntax
than the linux driver in order to link the dsa ports to the mdio bus.
- update defconfig
- replace mv88e61xx_hw_reset weak override with board_phy_config support
for mv88e61xx configuration that is outside the scope of the DSA driver
Signed-off-by: Tim Harvey <tharvey at gateworks.com>
---
v4:
- use standard Linux internal MDIO dt structure
- use PHY_FIXED_ID define
v3:
- move mdio's mdio at 0 subnode
v2: no changes
---
arch/arm/dts/imx6qdl-gw5904.dtsi | 31 +++++++++++++++
board/gateworks/gw_ventana/gw_ventana.c | 50 +++++++++----------------
configs/gwventana_gw5904_defconfig | 8 ++--
drivers/net/mv88e6xxx.c | 29 ++++++--------
4 files changed, 65 insertions(+), 53 deletions(-)
diff --git a/arch/arm/dts/imx6qdl-gw5904.dtsi b/arch/arm/dts/imx6qdl-gw5904.dtsi
index 612b6e068e28..487dd7648274 100644
--- a/arch/arm/dts/imx6qdl-gw5904.dtsi
+++ b/arch/arm/dts/imx6qdl-gw5904.dtsi
@@ -212,6 +212,27 @@
compatible = "marvell,mv88e6085";
reg = <0>;
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sw_phy0: ethernet-phy at 0 {
+ reg = <0x0>;
+ };
+
+ sw_phy1: ethernet-phy at 1 {
+ reg = <0x1>;
+ };
+
+ sw_phy2: ethernet-phy at 2 {
+ reg = <0x2>;
+ };
+
+ sw_phy3: ethernet-phy at 3 {
+ reg = <0x3>;
+ };
+ };
+
ports {
#address-cells = <1>;
#size-cells = <0>;
@@ -219,27 +240,37 @@
port at 0 {
reg = <0>;
label = "lan4";
+ phy-handle = <&sw_phy0>;
};
port at 1 {
reg = <1>;
label = "lan3";
+ phy-handle = <&sw_phy1>;
};
port at 2 {
reg = <2>;
label = "lan2";
+ phy-handle = <&sw_phy2>;
};
port at 3 {
reg = <3>;
label = "lan1";
+ phy-handle = <&sw_phy3>;
};
port at 5 {
reg = <5>;
label = "cpu";
ethernet = <&fec>;
+ phy-mode = "rgmii-id";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
};
};
};
diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c
index 99f52b9953e2..1c3da2c82707 100644
--- a/board/gateworks/gw_ventana/gw_ventana.c
+++ b/board/gateworks/gw_ventana/gw_ventana.c
@@ -83,44 +83,30 @@ int board_phy_config(struct phy_device *phydev)
break;
}
+ /* Fixed PHY: for GW5904/GW5909 this is Marvell 88E6176 GbE Switch */
+ if (phydev->phy_id == PHY_FIXED_ID &&
+ (board_type == GW5904 || board_type == GW5909)) {
+ struct mii_dev *bus = miiphy_get_dev_by_name("mdio");
+
+ puts("MV88E61XX ");
+ /* GPIO[0] output CLK125 for RGMII_REFCLK */
+ bus->write(bus, 0x1c, 0, 0x1a, (1 << 15) | (0x62 << 8) | 0xfe);
+ bus->write(bus, 0x1c, 0, 0x1a, (1 << 15) | (0x68 << 8) | 7);
+
+ /* Port 0-3 LED configuration: Table 80/82 */
+ /* LED configuration: 7:4-green (8=Activity) 3:0 amber (8=Link) */
+ bus->write(bus, 0x10, 0, 0x16, 0x8088);
+ bus->write(bus, 0x11, 0, 0x16, 0x8088);
+ bus->write(bus, 0x12, 0, 0x16, 0x8088);
+ bus->write(bus, 0x13, 0, 0x16, 0x8088);
+ }
+
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
-#ifdef CONFIG_MV88E61XX_SWITCH
-int mv88e61xx_hw_reset(struct phy_device *phydev)
-{
- struct mii_dev *bus = phydev->bus;
-
- /* GPIO[0] output, CLK125 */
- debug("enabling RGMII_REFCLK\n");
- bus->write(bus, 0x1c /*MV_GLOBAL2*/, 0,
- 0x1a /*MV_SCRATCH_MISC*/,
- (1 << 15) | (0x62 /*MV_GPIO_DIR*/ << 8) | 0xfe);
- bus->write(bus, 0x1c /*MV_GLOBAL2*/, 0,
- 0x1a /*MV_SCRATCH_MISC*/,
- (1 << 15) | (0x68 /*MV_GPIO01_CNTL*/ << 8) | 7);
-
- /* RGMII delay - Physical Control register bit[15:14] */
- debug("setting port%d RGMII rx/tx delay\n", CONFIG_MV88E61XX_CPU_PORT);
- /* forced 1000mbps full-duplex link */
- bus->write(bus, 0x10 + CONFIG_MV88E61XX_CPU_PORT, 0, 1, 0xc0fe);
- phydev->autoneg = AUTONEG_DISABLE;
- phydev->speed = SPEED_1000;
- phydev->duplex = DUPLEX_FULL;
-
- /* LED configuration: 7:4-green (8=Activity) 3:0 amber (8=Link) */
- bus->write(bus, 0x10, 0, 0x16, 0x8088);
- bus->write(bus, 0x11, 0, 0x16, 0x8088);
- bus->write(bus, 0x12, 0, 0x16, 0x8088);
- bus->write(bus, 0x13, 0, 0x16, 0x8088);
-
- return 0;
-}
-#endif // CONFIG_MV88E61XX_SWITCH
-
#if defined(CONFIG_VIDEO_IPUV3)
static void enable_hdmi(struct display_info_t const *dev)
{
diff --git a/configs/gwventana_gw5904_defconfig b/configs/gwventana_gw5904_defconfig
index 8c6baf0ae5e2..33b57c5a1c5d 100644
--- a/configs/gwventana_gw5904_defconfig
+++ b/configs/gwventana_gw5904_defconfig
@@ -111,11 +111,11 @@ CONFIG_SUPPORT_EMMC_BOOT=y
CONFIG_FSL_USDHC=y
CONFIG_MTD=y
CONFIG_PHYLIB=y
-CONFIG_MV88E61XX_SWITCH=y
-CONFIG_MV88E61XX_CPU_PORT=5
-CONFIG_MV88E61XX_PHY_PORTS=0xf
-CONFIG_MV88E61XX_FIXED_PORTS=0x0
+CONFIG_MV88E61XX=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
CONFIG_DM_MDIO=y
+CONFIG_DM_DSA=y
CONFIG_E1000=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
diff --git a/drivers/net/mv88e6xxx.c b/drivers/net/mv88e6xxx.c
index a3a3f6cf4acc..6064bb73257b 100644
--- a/drivers/net/mv88e6xxx.c
+++ b/drivers/net/mv88e6xxx.c
@@ -727,31 +727,26 @@ static const struct dsa_ops mv88e6xxx_dsa_ops = {
static int mv88e6xxx_probe_mdio(struct udevice *dev)
{
struct udevice *mdev;
- ofnode node, mdios;
const char *name;
+ ofnode node;
int ret;
- /* bind phy ports of mdios child node to mv88e6xxx_mdio device */
- mdios = dev_read_subnode(dev, "mdios");
- if (!ofnode_valid(mdios))
+ /* bind phy ports of mdio child node to mv88e6xxx_mdio device */
+ node = dev_read_subnode(dev, "mdio");
+ if (!ofnode_valid(node))
return 0;
- ofnode_for_each_subnode(node, mdios) {
- name = ofnode_get_name(node);
- ret = device_bind_driver_to_node(dev,
- "mv88e6xxx_mdio",
- name, node, NULL);
- if (ret) {
- dev_err(dev, "failed to bind %s: %d\n", name, ret);
- continue;
- }
-
+ name = ofnode_get_name(node);
+ ret = device_bind_driver_to_node(dev,
+ "mv88e6xxx_mdio",
+ name, node, NULL);
+ if (ret) {
+ dev_err(dev, "failed to bind %s: %d\n", name, ret);
+ } else {
/* need to probe it as there is no compatible to do so */
ret = uclass_get_device_by_ofnode(UCLASS_MDIO, node, &mdev);
- if (ret) {
+ if (ret)
dev_err(dev, "failed to probe %s: %d\n", name, ret);
- continue;
- }
}
return ret;
--
2.25.1
More information about the U-Boot
mailing list