[PATCH v2 u-boot-mvebu 4/4] arm: mvebu: clearfog: Update eMMC/SD/SATA instructions

[Stefan Roese]

Hi Pali,

On 4/27/23 01:44, Pali Rohár wrote:
> On Thursday 13 April 2023 22:43:25 Martin Rowe wrote:
>> On Thu, 13 Apr 2023 at 20:58, Pali Rohár <pali at kernel.org> wrote:
>>>
>>> BootROM and neither SPL does not use eMMC boot acknowledgement or boot
>>> enable bits in EXT_CSD_PART_CONF eMMC register. And also fixed SATA disk
>>> sector 0x141 is not used at all.
>>>
>>> Signed-off-by: Pali Rohár <pali at kernel.org>
>>
>> SPL successfully loads u-boot from the same partition as SPL. SD card
>> and UART continue to boot.
>>
>> Thanks Pali!
>>
>> Tested-by: Martin Rowe <martin.p.rowe at gmail.com>
> 
> Ok, is something more needed for this patch series?

Unfortunately yes. As at least this board breaks with this patchset
added:

$ make sama5d2_icp_mmc_defconfig
$ make -sj
/opt/kernel.org/gcc-12.2.0-nolibc/arm-linux-gnueabi/bin/arm-linux-gnueabi-ld.bfd: 
u-boot-spl section `__u_boot_list' will not fit in region `.sram'
/opt/kernel.org/gcc-12.2.0-nolibc/arm-linux-gnueabi/bin/arm-linux-gnueabi-ld.bfd: 
region `.sram' overflowed by 32 bytes
make[1]: *** [scripts/Makefile.spl:527: spl/u-boot-spl] Error 1
make: *** [Makefile:2049: spl/u-boot-spl] Error 2

So CI build fails and I can't send a pull request. I'm sending a patch
though, to fix this image overflow by enabling LTO. Stay tuned...

Thanks,
Stefan

>>> ---
>>>   board/solidrun/clearfog/README | 20 ++++++++++----------
>>>   1 file changed, 10 insertions(+), 10 deletions(-)
>>>
>>> diff --git a/board/solidrun/clearfog/README b/board/solidrun/clearfog/README
>>> index ed4a712c5aa2..c86b37061a30 100644
>>> --- a/board/solidrun/clearfog/README
>>> +++ b/board/solidrun/clearfog/README
>>> @@ -1,7 +1,7 @@
>>>   Update from original Marvell U-Boot to mainline U-Boot:
>>>   -------------------------------------------------------
>>>
>>> -Generate the U-Boot image with these commands:
>>> +Generate the U-Boot image for eMMC/SD with these commands:
>>>
>>>   $ make clearfog_defconfig
>>>   $ make
>>> @@ -9,7 +9,7 @@ $ make
>>>   The resulting image including the SPL binary with the
>>>   full DDR setup is "u-boot-with-spl.kwb".
>>>
>>> -Now all you need to do is copy this image on a SD card.
>>> +Now all you need to do is copy this image on a SD card's sector 1.
>>>   For example with this command:
>>>
>>>   $ sudo dd if=u-boot-with-spl.kwb of=/dev/sdX bs=512 seek=1
>>> @@ -20,12 +20,6 @@ of "/dev/sdX" here!
>>>   Install U-Boot on eMMC:
>>>   -----------------------
>>>
>>> -To make SPL load the main U-Boot image from the eMMC boot partition enable
>>> -eMMC boot acknowledgement and boot partition with the following U-Boot
>>> -command:
>>> -
>>> -  mmc partconf 0 1 1 0
>>> -
>>>   Install U-Boot on eMMC boot partition from Linux running on Clearfog:
>>>
>>>     echo 0 > /sys/block/mmcblk0boot0/force_ro
>>> @@ -37,8 +31,14 @@ Consider initial boot from UART (see below).
>>>   Install U-Boot on SATA:
>>>   -----------------------
>>>
>>> -When loading the main U-Boot image from raw SATA sector, set
>>> -CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR to 0x141.
>>> +Generate the U-Boot image for SATA with these commands:
>>> +
>>> +$ make clearfog_sata_defconfig
>>> +$ make
>>> +
>>> +Copy image on a SATA disk's sector 1:
>>> +
>>> +$ sudo dd if=u-boot-with-spl.kwb of=/dev/sdX bs=512 seek=1
>>>
>>>   Boot selection:
>>>   ---------------
>>> --
>>> 2.20.1
>>>

Viele Grüße,
Stefan Roese

-- 
DENX Software Engineering GmbH,      Managing Director: Erika Unter
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de