[PATCH 3/3] arm: dts: imx8mp: Sync with Linux 6.3
Adam Ford
aford173 at gmail.com
Thu Apr 27 21:22:30 CEST 2023
On Thu, Apr 27, 2023 at 1:09 PM Fabio Estevam <festevam at gmail.com> wrote:
>
> From: Fabio Estevam <festevam at denx.de>
>
> Sync imx8mp.dtsi and imx8mp-clock.h with Linux 6.3.
>
> Signed-off-by: Fabio Estevam <festevam at denx.de>
Reviewed-by: Adam Ford <aford173 at gmail.com>
> ---
> arch/arm/dts/imx8mp.dtsi | 374 ++++++++++++++++-------
> include/dt-bindings/clock/imx8mp-clock.h | 14 +-
> 2 files changed, 270 insertions(+), 118 deletions(-)
>
> diff --git a/arch/arm/dts/imx8mp.dtsi b/arch/arm/dts/imx8mp.dtsi
> index bb916a0948a8..a237275ee017 100644
> --- a/arch/arm/dts/imx8mp.dtsi
> +++ b/arch/arm/dts/imx8mp.dtsi
> @@ -123,6 +123,7 @@
>
> A53_L2: l2-cache0 {
> compatible = "cache";
> + cache-unified;
> cache-level = <2>;
> cache-size = <0x80000>;
> cache-line-size = <64>;
> @@ -379,6 +380,8 @@
> compatible = "fsl,imx8mp-tmu";
> reg = <0x30260000 0x10000>;
> clocks = <&clk IMX8MP_CLK_TSENSOR_ROOT>;
> + nvmem-cells = <&tmu_calib>;
> + nvmem-cell-names = "calib";
> #thermal-sensor-cells = <1>;
> };
>
> @@ -411,7 +414,7 @@
> reg = <0x30330000 0x10000>;
> };
>
> - gpr: iomuxc-gpr at 30340000 {
> + gpr: syscon at 30340000 {
> compatible = "fsl,imx8mp-iomuxc-gpr", "syscon";
> reg = <0x30340000 0x10000>;
> };
> @@ -424,27 +427,44 @@
> #address-cells = <1>;
> #size-cells = <1>;
>
> - imx8mp_uid: unique-id at 420 {
> + /*
> + * The register address below maps to the MX8M
> + * Fusemap Description Table entries this way.
> + * Assuming
> + * reg = <ADDR SIZE>;
> + * then
> + * Fuse Address = (ADDR * 4) + 0x400
> + * Note that if SIZE is greater than 4, then
> + * each subsequent fuse is located at offset
> + * +0x10 in Fusemap Description Table (e.g.
> + * reg = <0x8 0x8> describes fuses 0x420 and
> + * 0x430).
> + */
> + imx8mp_uid: unique-id at 8 { /* 0x420-0x430 */
> reg = <0x8 0x8>;
> };
>
> - cpu_speed_grade: speed-grade at 10 {
> + cpu_speed_grade: speed-grade at 10 { /* 0x440 */
> reg = <0x10 4>;
> };
>
> - eth_mac1: mac-address at 90 {
> + eth_mac1: mac-address at 90 { /* 0x640 */
> reg = <0x90 6>;
> };
>
> - eth_mac2: mac-address at 96 {
> + eth_mac2: mac-address at 96 { /* 0x658 */
> reg = <0x96 6>;
> };
> +
> + tmu_calib: calib at 264 { /* 0xd90-0xdc0 */
> + reg = <0x264 0x10>;
> + };
> };
>
> - anatop: anatop at 30360000 {
> - compatible = "fsl,imx8mp-anatop", "fsl,imx8mm-anatop",
> - "syscon";
> + anatop: clock-controller at 30360000 {
> + compatible = "fsl,imx8mp-anatop", "fsl,imx8mm-anatop";
> reg = <0x30360000 0x10000>;
> + #clock-cells = <1>;
> };
>
> snvs: snvs at 30370000 {
> @@ -523,6 +543,7 @@
> compatible = "fsl,imx8mp-gpc";
> reg = <0x303a0000 0x1000>;
> interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
> interrupt-controller;
> #interrupt-cells = <3>;
>
> @@ -589,7 +610,7 @@
> reg = <IMX8MP_POWER_DOMAIN_MIPI_PHY2>;
> };
>
> - pgc_hsiomix: power-domains at 17 {
> + pgc_hsiomix: power-domain at 17 {
> #power-domain-cells = <0>;
> reg = <IMX8MP_POWER_DOMAIN_HSIOMIX>;
> clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
> @@ -631,6 +652,14 @@
> reg = <IMX8MP_POWER_DOMAIN_VPU_VC8000E>;
> clocks = <&clk IMX8MP_CLK_VPU_VC8KE_ROOT>;
> };
> +
> + pgc_mlmix: power-domain at 24 {
> + #power-domain-cells = <0>;
> + reg = <IMX8MP_POWER_DOMAIN_MLMIX>;
> + clocks = <&clk IMX8MP_CLK_ML_AXI>,
> + <&clk IMX8MP_CLK_ML_AHB>,
> + <&clk IMX8MP_CLK_NPU_ROOT>;
> + };
> };
> };
> };
> @@ -702,112 +731,129 @@
> #size-cells = <1>;
> ranges;
>
> - ecspi1: spi at 30820000 {
> + spba-bus at 30800000 {
> + compatible = "fsl,spba-bus", "simple-bus";
> + reg = <0x30800000 0x100000>;
> #address-cells = <1>;
> - #size-cells = <0>;
> - compatible = "fsl,imx8mp-ecspi", "fsl,imx51-ecspi";
> - reg = <0x30820000 0x10000>;
> - interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&clk IMX8MP_CLK_ECSPI1_ROOT>,
> - <&clk IMX8MP_CLK_ECSPI1_ROOT>;
> - clock-names = "ipg", "per";
> - dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> + #size-cells = <1>;
> + ranges;
>
> - ecspi2: spi at 30830000 {
> - #address-cells = <1>;
> - #size-cells = <0>;
> - compatible = "fsl,imx8mp-ecspi", "fsl,imx51-ecspi";
> - reg = <0x30830000 0x10000>;
> - interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&clk IMX8MP_CLK_ECSPI2_ROOT>,
> - <&clk IMX8MP_CLK_ECSPI2_ROOT>;
> - clock-names = "ipg", "per";
> - dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> + ecspi1: spi at 30820000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi";
> + reg = <0x30820000 0x10000>;
> + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MP_CLK_ECSPI1_ROOT>,
> + <&clk IMX8MP_CLK_ECSPI1_ROOT>;
> + clock-names = "ipg", "per";
> + assigned-clock-rates = <80000000>;
> + assigned-clocks = <&clk IMX8MP_CLK_ECSPI1>;
> + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>;
> + dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
>
> - ecspi3: spi at 30840000 {
> - #address-cells = <1>;
> - #size-cells = <0>;
> - compatible = "fsl,imx8mp-ecspi", "fsl,imx51-ecspi";
> - reg = <0x30840000 0x10000>;
> - interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&clk IMX8MP_CLK_ECSPI3_ROOT>,
> - <&clk IMX8MP_CLK_ECSPI3_ROOT>;
> - clock-names = "ipg", "per";
> - dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> + ecspi2: spi at 30830000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi";
> + reg = <0x30830000 0x10000>;
> + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MP_CLK_ECSPI2_ROOT>,
> + <&clk IMX8MP_CLK_ECSPI2_ROOT>;
> + clock-names = "ipg", "per";
> + assigned-clock-rates = <80000000>;
> + assigned-clocks = <&clk IMX8MP_CLK_ECSPI2>;
> + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>;
> + dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
>
> - uart1: serial at 30860000 {
> - compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart";
> - reg = <0x30860000 0x10000>;
> - interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&clk IMX8MP_CLK_UART1_ROOT>,
> - <&clk IMX8MP_CLK_UART1_ROOT>;
> - clock-names = "ipg", "per";
> - dmas = <&sdma1 22 4 0>, <&sdma1 23 4 0>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> + ecspi3: spi at 30840000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi";
> + reg = <0x30840000 0x10000>;
> + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MP_CLK_ECSPI3_ROOT>,
> + <&clk IMX8MP_CLK_ECSPI3_ROOT>;
> + clock-names = "ipg", "per";
> + assigned-clock-rates = <80000000>;
> + assigned-clocks = <&clk IMX8MP_CLK_ECSPI3>;
> + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>;
> + dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
>
> - uart3: serial at 30880000 {
> - compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart";
> - reg = <0x30880000 0x10000>;
> - interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&clk IMX8MP_CLK_UART3_ROOT>,
> - <&clk IMX8MP_CLK_UART3_ROOT>;
> - clock-names = "ipg", "per";
> - dmas = <&sdma1 26 4 0>, <&sdma1 27 4 0>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> + uart1: serial at 30860000 {
> + compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart";
> + reg = <0x30860000 0x10000>;
> + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MP_CLK_UART1_ROOT>,
> + <&clk IMX8MP_CLK_UART1_ROOT>;
> + clock-names = "ipg", "per";
> + dmas = <&sdma1 22 4 0>, <&sdma1 23 4 0>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
>
> - uart2: serial at 30890000 {
> - compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart";
> - reg = <0x30890000 0x10000>;
> - interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&clk IMX8MP_CLK_UART2_ROOT>,
> - <&clk IMX8MP_CLK_UART2_ROOT>;
> - clock-names = "ipg", "per";
> - dmas = <&sdma1 24 4 0>, <&sdma1 25 4 0>;
> - dma-names = "rx", "tx";
> - status = "disabled";
> - };
> + uart3: serial at 30880000 {
> + compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart";
> + reg = <0x30880000 0x10000>;
> + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MP_CLK_UART3_ROOT>,
> + <&clk IMX8MP_CLK_UART3_ROOT>;
> + clock-names = "ipg", "per";
> + dmas = <&sdma1 26 4 0>, <&sdma1 27 4 0>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
>
> - flexcan1: can at 308c0000 {
> - compatible = "fsl,imx8mp-flexcan";
> - reg = <0x308c0000 0x10000>;
> - interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&clk IMX8MP_CLK_IPG_ROOT>,
> - <&clk IMX8MP_CLK_CAN1_ROOT>;
> - clock-names = "ipg", "per";
> - assigned-clocks = <&clk IMX8MP_CLK_CAN1>;
> - assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_40M>;
> - assigned-clock-rates = <40000000>;
> - fsl,clk-source = /bits/ 8 <0>;
> - fsl,stop-mode = <&gpr 0x10 4>;
> - status = "disabled";
> - };
> + uart2: serial at 30890000 {
> + compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart";
> + reg = <0x30890000 0x10000>;
> + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MP_CLK_UART2_ROOT>,
> + <&clk IMX8MP_CLK_UART2_ROOT>;
> + clock-names = "ipg", "per";
> + dmas = <&sdma1 24 4 0>, <&sdma1 25 4 0>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
>
> - flexcan2: can at 308d0000 {
> - compatible = "fsl,imx8mp-flexcan";
> - reg = <0x308d0000 0x10000>;
> - interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&clk IMX8MP_CLK_IPG_ROOT>,
> - <&clk IMX8MP_CLK_CAN2_ROOT>;
> - clock-names = "ipg", "per";
> - assigned-clocks = <&clk IMX8MP_CLK_CAN2>;
> - assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_40M>;
> - assigned-clock-rates = <40000000>;
> - fsl,clk-source = /bits/ 8 <0>;
> - fsl,stop-mode = <&gpr 0x10 5>;
> - status = "disabled";
> + flexcan1: can at 308c0000 {
> + compatible = "fsl,imx8mp-flexcan";
> + reg = <0x308c0000 0x10000>;
> + interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MP_CLK_IPG_ROOT>,
> + <&clk IMX8MP_CLK_CAN1_ROOT>;
> + clock-names = "ipg", "per";
> + assigned-clocks = <&clk IMX8MP_CLK_CAN1>;
> + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_40M>;
> + assigned-clock-rates = <40000000>;
> + fsl,clk-source = /bits/ 8 <0>;
> + fsl,stop-mode = <&gpr 0x10 4>;
> + status = "disabled";
> + };
> +
> + flexcan2: can at 308d0000 {
> + compatible = "fsl,imx8mp-flexcan";
> + reg = <0x308d0000 0x10000>;
> + interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MP_CLK_IPG_ROOT>,
> + <&clk IMX8MP_CLK_CAN2_ROOT>;
> + clock-names = "ipg", "per";
> + assigned-clocks = <&clk IMX8MP_CLK_CAN2>;
> + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_40M>;
> + assigned-clock-rates = <40000000>;
> + fsl,clk-source = /bits/ 8 <0>;
> + fsl,stop-mode = <&gpr 0x10 5>;
> + status = "disabled";
> + };
> };
>
> crypto: crypto at 30900000 {
> @@ -1063,11 +1109,11 @@
> noc_opp_table: opp-table {
> compatible = "operating-points-v2";
>
> - opp-200M {
> + opp-200000000 {
> opp-hz = /bits/ 64 <200000000>;
> };
>
> - opp-1000M {
> + opp-1000000000 {
> opp-hz = /bits/ 64 <1000000000>;
> };
> };
> @@ -1080,10 +1126,35 @@
> #size-cells = <1>;
> ranges;
>
> + lcdif2: display-controller at 32e90000 {
> + compatible = "fsl,imx8mp-lcdif";
> + reg = <0x32e90000 0x10000>;
> + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MP_CLK_MEDIA_DISP2_PIX_ROOT>,
> + <&clk IMX8MP_CLK_MEDIA_APB_ROOT>,
> + <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>;
> + clock-names = "pix", "axi", "disp_axi";
> + assigned-clocks = <&clk IMX8MP_CLK_MEDIA_DISP2_PIX>,
> + <&clk IMX8MP_VIDEO_PLL1>;
> + assigned-clock-parents = <&clk IMX8MP_VIDEO_PLL1_OUT>,
> + <&clk IMX8MP_VIDEO_PLL1_REF_SEL>;
> + assigned-clock-rates = <0>, <1039500000>;
> + power-domains = <&media_blk_ctrl IMX8MP_MEDIABLK_PD_LCDIF_2>;
> + status = "disabled";
> +
> + port {
> + lcdif2_to_ldb: endpoint {
> + remote-endpoint = <&ldb_from_lcdif2>;
> + };
> + };
> + };
> +
> media_blk_ctrl: blk-ctrl at 32ec0000 {
> compatible = "fsl,imx8mp-media-blk-ctrl",
> - "syscon";
> + "simple-bus", "syscon";
> reg = <0x32ec0000 0x10000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> power-domains = <&pgc_mediamix>,
> <&pgc_mipi_phy1>,
> <&pgc_mipi_phy1>,
> @@ -1128,6 +1199,44 @@
> assigned-clock-rates = <500000000>, <200000000>;
>
> #power-domain-cells = <1>;
> +
> + lvds_bridge: bridge at 5c {
> + compatible = "fsl,imx8mp-ldb";
> + clocks = <&clk IMX8MP_CLK_MEDIA_LDB>;
> + clock-names = "ldb";
> + reg = <0x5c 0x4>, <0x128 0x4>;
> + reg-names = "ldb", "lvds";
> + assigned-clocks = <&clk IMX8MP_CLK_MEDIA_LDB>;
> + assigned-clock-parents = <&clk IMX8MP_VIDEO_PLL1_OUT>;
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> +
> + ldb_from_lcdif2: endpoint {
> + remote-endpoint = <&lcdif2_to_ldb>;
> + };
> + };
> +
> + port at 1 {
> + reg = <1>;
> +
> + ldb_lvds_ch0: endpoint {
> + };
> + };
> +
> + port at 2 {
> + reg = <2>;
> +
> + ldb_lvds_ch1: endpoint {
> + };
> + };
> + };
> + };
> };
>
> pcie_phy: pcie-phy at 32f00000 {
> @@ -1158,6 +1267,7 @@
> <&noc IMX8MP_ICM_PCIE &noc IMX8MP_ICN_HSIO>;
> interconnect-names = "noc-pcie", "usb1", "usb2", "pcie";
> #power-domain-cells = <1>;
> + #clock-cells = <0>;
> };
> };
>
> @@ -1165,6 +1275,13 @@
> compatible = "fsl,imx8mp-pcie";
> reg = <0x33800000 0x400000>, <0x1ff00000 0x80000>;
> reg-names = "dbi", "config";
> + clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
> + <&clk IMX8MP_CLK_HSIO_AXI>,
> + <&clk IMX8MP_CLK_PCIE_ROOT>;
> + clock-names = "pcie", "pcie_bus", "pcie_aux";
> + assigned-clocks = <&clk IMX8MP_CLK_PCIE_AUX>;
> + assigned-clock-rates = <10000000>;
> + assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_50M>;
> #address-cells = <3>;
> #size-cells = <2>;
> device_type = "pci";
> @@ -1223,6 +1340,28 @@
> power-domains = <&pgc_gpu2d>;
> };
>
> + vpu_g1: video-codec at 38300000 {
> + compatible = "nxp,imx8mm-vpu-g1";
> + reg = <0x38300000 0x10000>;
> + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MP_CLK_VPU_G1_ROOT>;
> + assigned-clocks = <&clk IMX8MP_CLK_VPU_G1>;
> + assigned-clock-parents = <&clk IMX8MP_VPU_PLL_OUT>;
> + assigned-clock-rates = <600000000>;
> + power-domains = <&vpumix_blk_ctrl IMX8MP_VPUBLK_PD_G1>;
> + };
> +
> + vpu_g2: video-codec at 38310000 {
> + compatible = "nxp,imx8mq-vpu-g2";
> + reg = <0x38310000 0x10000>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clk IMX8MP_CLK_VPU_G2_ROOT>;
> + assigned-clocks = <&clk IMX8MP_CLK_VPU_G2>;
> + assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_1000M>;
> + assigned-clock-rates = <500000000>;
> + power-domains = <&vpumix_blk_ctrl IMX8MP_VPUBLK_PD_G2>;
> + };
> +
> vpumix_blk_ctrl: blk-ctrl at 38330000 {
> compatible = "fsl,imx8mp-vpu-blk-ctrl", "syscon";
> reg = <0x38330000 0x100>;
> @@ -1234,6 +1373,9 @@
> <&clk IMX8MP_CLK_VPU_G2_ROOT>,
> <&clk IMX8MP_CLK_VPU_VC8KE_ROOT>;
> clock-names = "g1", "g2", "vc8000e";
> + assigned-clocks = <&clk IMX8MP_CLK_VPU_BUS>, <&clk IMX8MP_VPU_PLL>;
> + assigned-clock-parents = <&clk IMX8MP_VPU_PLL_OUT>;
> + assigned-clock-rates = <600000000>, <600000000>;
> interconnects = <&noc IMX8MP_ICM_VPU_G1 &noc IMX8MP_ICN_VIDEO>,
> <&noc IMX8MP_ICM_VPU_G2 &noc IMX8MP_ICN_VIDEO>,
> <&noc IMX8MP_ICM_VPU_H1 &noc IMX8MP_ICN_VIDEO>;
> @@ -1279,7 +1421,7 @@
> reg = <0x32f10100 0x8>,
> <0x381f0000 0x20>;
> clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
> - <&clk IMX8MP_CLK_USB_ROOT>;
> + <&clk IMX8MP_CLK_USB_SUSP>;
> clock-names = "hsio", "suspend";
> interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
> power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB>;
> @@ -1292,9 +1434,9 @@
> usb_dwc3_0: usb at 38100000 {
> compatible = "snps,dwc3";
> reg = <0x38100000 0x10000>;
> - clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
> + clocks = <&clk IMX8MP_CLK_USB_ROOT>,
> <&clk IMX8MP_CLK_USB_CORE_REF>,
> - <&clk IMX8MP_CLK_USB_ROOT>;
> + <&clk IMX8MP_CLK_USB_SUSP>;
> clock-names = "bus_early", "ref", "suspend";
> interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
> phys = <&usb3_phy0>, <&usb3_phy0>;
> @@ -1321,7 +1463,7 @@
> reg = <0x32f10108 0x8>,
> <0x382f0000 0x20>;
> clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
> - <&clk IMX8MP_CLK_USB_ROOT>;
> + <&clk IMX8MP_CLK_USB_SUSP>;
> clock-names = "hsio", "suspend";
> interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
> power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB>;
> @@ -1334,9 +1476,9 @@
> usb_dwc3_1: usb at 38200000 {
> compatible = "snps,dwc3";
> reg = <0x38200000 0x10000>;
> - clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
> + clocks = <&clk IMX8MP_CLK_USB_ROOT>,
> <&clk IMX8MP_CLK_USB_CORE_REF>,
> - <&clk IMX8MP_CLK_USB_ROOT>;
> + <&clk IMX8MP_CLK_USB_SUSP>;
> clock-names = "bus_early", "ref", "suspend";
> interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> phys = <&usb3_phy1>, <&usb3_phy1>;
> diff --git a/include/dt-bindings/clock/imx8mp-clock.h b/include/dt-bindings/clock/imx8mp-clock.h
> index 9d5cc2ddde89..3f28ce685f41 100644
> --- a/include/dt-bindings/clock/imx8mp-clock.h
> +++ b/include/dt-bindings/clock/imx8mp-clock.h
> @@ -324,8 +324,18 @@
> #define IMX8MP_CLK_CLKOUT2_SEL 317
> #define IMX8MP_CLK_CLKOUT2_DIV 318
> #define IMX8MP_CLK_CLKOUT2 319
> -
> -#define IMX8MP_CLK_END 320
> +#define IMX8MP_CLK_USB_SUSP 320
> +#define IMX8MP_CLK_AUDIO_AHB_ROOT IMX8MP_CLK_AUDIO_ROOT
> +#define IMX8MP_CLK_AUDIO_AXI_ROOT 321
> +#define IMX8MP_CLK_SAI1_ROOT 322
> +#define IMX8MP_CLK_SAI2_ROOT 323
> +#define IMX8MP_CLK_SAI3_ROOT 324
> +#define IMX8MP_CLK_SAI5_ROOT 325
> +#define IMX8MP_CLK_SAI6_ROOT 326
> +#define IMX8MP_CLK_SAI7_ROOT 327
> +#define IMX8MP_CLK_PDM_ROOT 328
> +#define IMX8MP_CLK_MEDIA_LDB_ROOT 329
> +#define IMX8MP_CLK_END 330
>
> #define IMX8MP_CLK_AUDIOMIX_SAI1_IPG 0
> #define IMX8MP_CLK_AUDIOMIX_SAI1_MCLK1 1
> --
> 2.34.1
>
More information about the U-Boot
mailing list