[PATCH 1/1] [u-boot][master][PATCH v2] pico-imx7d: add baseboard SD card boot detect
egyszeregy at freemail.hu
egyszeregy at freemail.hu
Wed Aug 2 15:41:53 CEST 2023
From: Benjamin Szőke <egyszeregy at freemail.hu>
Take over codes from Techenxion to support mmc autodetect boot for pico-imx7d.
Signed-off-by: Benjamin Szőke <egyszeregy at freemail.hu>
---
board/technexion/pico-imx7d/pico-imx7d.c | 60 ++++++++++++++++
board/technexion/pico-imx7d/spl.c | 91 ++++++++++++++++++++++--
include/configs/pico-imx7d.h | 4 +-
3 files changed, 147 insertions(+), 8 deletions(-)
diff --git a/board/technexion/pico-imx7d/pico-imx7d.c b/board/technexion/pico-imx7d/pico-imx7d.c
index 6e98b85b28..5c807646cf 100644
--- a/board/technexion/pico-imx7d/pico-imx7d.c
+++ b/board/technexion/pico-imx7d/pico-imx7d.c
@@ -19,6 +19,7 @@
#include <power/pmic.h>
#include <power/pfuze3000_pmic.h>
#include "../../freescale/common/pfuze.h"
+#include <asm/mach-imx/boot_mode.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -129,6 +130,53 @@ int board_phy_config(struct phy_device *phydev)
}
#endif
+#if CONFIG_IS_ENABLED(FSL_ESDHC_IMX)
+int check_mmc_autodetect(void)
+{
+ char *autodetect_str = env_get("mmcautodetect");
+
+ if ((autodetect_str != NULL) &&
+ (strcmp(autodetect_str, "yes") == 0)) {
+ return 1;
+ }
+
+ return 0;
+}
+
+void board_late_mmc_init(void)
+{
+ int dev_no = 0;
+ char cmd[32];
+ char mmcblk[32];
+
+ if (!check_mmc_autodetect())
+ return;
+
+ switch (get_boot_device()) {
+ case SD3_BOOT:
+ case MMC3_BOOT:
+ env_set("bootdev", "MMC3");
+ dev_no = 2;
+ break;
+ case SD1_BOOT:
+ env_set("bootdev", "SD1");
+ dev_no = 0;
+ break;
+ default:
+ printf("Wrong boot device!");
+ }
+
+ env_set_ulong("mmcdev", dev_no);
+
+ /* Set mmcblk env */
+ sprintf(mmcblk, "/dev/mmcblk%dp2 rootwait rw", dev_no);
+ env_set("mmcroot", mmcblk);
+
+ sprintf(cmd, "mmc dev %d", dev_no);
+ run_command(cmd, 0);
+}
+#endif
+
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
@@ -176,6 +224,12 @@ int board_late_init(void)
set_wdog_reset(wdog);
+#if CONFIG_IS_ENABLED(FSL_ESDHC_IMX)
+#if defined(CONFIG_ENV_IS_IN_MMC) || defined(CONFIG_ENV_IS_NOWHERE)
+ board_late_mmc_init();
+#endif /* CONFIG_ENV_IS_IN_MMC or CONFIG_ENV_IS_NOWHERE */
+#endif
+
/*
* Do not assert internal WDOG_RESET_B_DEB(controlled by bit 4),
* since we use PMIC_PWRON to reset the board.
@@ -210,3 +264,9 @@ int board_ehci_hcd_init(int port)
}
return 0;
}
+
+/* This should be defined for each board */
+__weak int mmc_map_to_kernel_blk(int dev_no)
+{
+ return dev_no;
+}
diff --git a/board/technexion/pico-imx7d/spl.c b/board/technexion/pico-imx7d/spl.c
index f86fee9c88..9d931fc067 100644
--- a/board/technexion/pico-imx7d/spl.c
+++ b/board/technexion/pico-imx7d/spl.c
@@ -18,6 +18,7 @@
#include <asm/gpio.h>
#include <fsl_esdhc_imx.h>
#include <spl.h>
+#include <asm/mach-imx/boot_mode.h>
#if defined(CONFIG_SPL_BUILD)
@@ -158,7 +159,20 @@ void reset_cpu(void)
#define USDHC_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
-static iomux_v3_cfg_t const usdhc3_pads[] = {
+#define USDHC1_CD_GPIO IMX_GPIO_NR(5, 0)
+/* EMMC/SD */
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+ MX7D_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD1_DATA0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD1_DATA1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD1_DATA2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD1_DATA3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX7D_PAD_SD1_CD_B__GPIO5_IO0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+#define USDHC3_CD_GPIO IMX_GPIO_NR(1, 14)
+static iomux_v3_cfg_t const usdhc3_emmc_pads[] = {
MX7D_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX7D_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX7D_PAD_SD3_DATA0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
@@ -172,20 +186,83 @@ static iomux_v3_cfg_t const usdhc3_pads[] = {
MX7D_PAD_GPIO1_IO14__GPIO1_IO14 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
};
-static struct fsl_esdhc_cfg usdhc_cfg[1] = {
+static struct fsl_esdhc_cfg usdhc_cfg[2] = {
{USDHC3_BASE_ADDR},
+ {USDHC1_BASE_ADDR},
};
int board_mmc_getcd(struct mmc *mmc)
{
- /* Assume uSDHC3 emmc is always present */
- return 1;
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC1_BASE_ADDR:
+ ret = !gpio_get_value(USDHC1_CD_GPIO); /* Assume uSDHC1 sd is always present */
+ break;
+ case USDHC3_BASE_ADDR:
+ ret = !gpio_get_value(USDHC3_CD_GPIO); /* Assume uSDHC3 emmc is always present */
+ break;
+ }
+
+ return ret;
}
int board_mmc_init(struct bd_info *bis)
{
- imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+ int ret;
+ u32 index = 0;
+
+ /*
+ * Following map is done:
+ * (USDHC) (Physical Port)
+ * usdhc3 SOM MicroSD/MMC
+ * usdhc1 Carrier board MicroSD
+ * Always set boot USDHC as mmc0
+ */
+
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc3_emmc_pads, ARRAY_SIZE(usdhc3_emmc_pads));
+ gpio_direction_input(USDHC3_CD_GPIO);
+
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+ gpio_direction_input(USDHC1_CD_GPIO);
+
+ switch (get_boot_device()) {
+ case SD1_BOOT:
+ usdhc_cfg[0].esdhc_base = USDHC1_BASE_ADDR;
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ usdhc_cfg[0].max_bus_width = 4;
+ usdhc_cfg[1].esdhc_base = USDHC3_BASE_ADDR;
+ usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ usdhc_cfg[1].max_bus_width = 4;
+ break;
+ case MMC3_BOOT:
+ usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ usdhc_cfg[0].max_bus_width = 8;
+ usdhc_cfg[1].esdhc_base = USDHC1_BASE_ADDR;
+ usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ usdhc_cfg[1].max_bus_width = 4;
+ break;
+ case SD3_BOOT:
+ default:
+ usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ usdhc_cfg[0].max_bus_width = 4;
+ usdhc_cfg[1].esdhc_base = USDHC1_BASE_ADDR;
+ usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ usdhc_cfg[1].max_bus_width = 4;
+ break;
+ }
+
+ for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
}
#endif
diff --git a/include/configs/pico-imx7d.h b/include/configs/pico-imx7d.h
index 096e5bbe66..f797bd51af 100644
--- a/include/configs/pico-imx7d.h
+++ b/include/configs/pico-imx7d.h
@@ -13,7 +13,7 @@
#define CFG_MXC_UART_BASE UART5_IPS_BASE_ADDR
/* MMC Config */
-#define CFG_SYS_FSL_ESDHC_ADDR 0
+#define CFG_SYS_FSL_ESDHC_ADDR USDHC3_BASE_ADDR
#define CFG_DFU_ENV_SETTINGS \
"dfu_alt_info=" \
@@ -79,9 +79,11 @@
"name=rootfs,size=0,uuid=${uuid_gpt_rootfs}\0" \
"fastboot_partition_alias_system=rootfs\0" \
"setup_emmc=mmc dev 0; gpt write mmc 0 $partitions; reset;\0" \
+ "mmcautodetect=yes\0" \
PICO_BOOT_ENV
#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 2) \
func(MMC, mmc, 0) \
func(USB, usb, 0) \
func(PXE, pxe, na) \
--
2.41.0.windows.3
More information about the U-Boot
mailing list