[PATCH] ARM: dts: stm32mp: alignment with v6.4
Patrice CHOTARD
patrice.chotard at foss.st.com
Fri Aug 4 18:01:04 CEST 2023
On 7/10/23 10:38, Patrick Delaunay wrote:
> Device tree alignment with Linux kernel v6.4.
>
> Signed-off-by: Patrick Delaunay <patrick.delaunay at foss.st.com>
> ---
>
> arch/arm/dts/stm32mp13-pinctrl.dtsi | 129 ++++++++++++++++++++++++++++
> arch/arm/dts/stm32mp131.dtsi | 99 ++++++++++++++++++++-
> arch/arm/dts/stm32mp135f-dk.dts | 42 ++++++++-
> arch/arm/dts/stm32mp15-pinctrl.dtsi | 34 ++++----
> arch/arm/dts/stm32mp151.dtsi | 4 +-
> arch/arm/dts/stm32mp157a-dk1.dts | 3 -
> arch/arm/dts/stm32mp157c-dk2.dts | 3 -
> arch/arm/dts/stm32mp157c-ed1.dts | 17 +---
> arch/arm/dts/stm32mp157c-ev1.dts | 9 +-
> arch/arm/dts/stm32mp15xx-dkx.dtsi | 15 ++--
> 10 files changed, 299 insertions(+), 56 deletions(-)
>
> diff --git a/arch/arm/dts/stm32mp13-pinctrl.dtsi b/arch/arm/dts/stm32mp13-pinctrl.dtsi
> index b2dce3a29f39..27e0c3826789 100644
> --- a/arch/arm/dts/stm32mp13-pinctrl.dtsi
> +++ b/arch/arm/dts/stm32mp13-pinctrl.dtsi
> @@ -258,4 +258,133 @@
> bias-disable;
> };
> };
> +
> + uart4_idle_pins_a: uart4-idle-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('D', 6, ANALOG)>; /* UART4_TX */
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('D', 8, AF8)>; /* UART4_RX */
> + bias-disable;
> + };
> + };
> +
> + uart4_sleep_pins_a: uart4-sleep-0 {
> + pins {
> + pinmux = <STM32_PINMUX('D', 6, ANALOG)>, /* UART4_TX */
> + <STM32_PINMUX('D', 8, ANALOG)>; /* UART4_RX */
> + };
> + };
> +
> + uart8_pins_a: uart8-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('E', 1, AF8)>; /* UART8_TX */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <0>;
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('F', 9, AF8)>; /* UART8_RX */
> + bias-pull-up;
> + };
> + };
> +
> + uart8_idle_pins_a: uart8-idle-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('E', 1, ANALOG)>; /* UART8_TX */
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('F', 9, AF8)>; /* UART8_RX */
> + bias-pull-up;
> + };
> + };
> +
> + uart8_sleep_pins_a: uart8-sleep-0 {
> + pins {
> + pinmux = <STM32_PINMUX('E', 1, ANALOG)>, /* UART8_TX */
> + <STM32_PINMUX('F', 9, ANALOG)>; /* UART8_RX */
> + };
> + };
> +
> + usart1_pins_a: usart1-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('C', 0, AF7)>, /* USART1_TX */
> + <STM32_PINMUX('C', 2, AF7)>; /* USART1_RTS */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <0>;
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('B', 0, AF4)>, /* USART1_RX */
> + <STM32_PINMUX('A', 7, AF7)>; /* USART1_CTS_NSS */
> + bias-pull-up;
> + };
> + };
> +
> + usart1_idle_pins_a: usart1-idle-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('C', 0, ANALOG)>, /* USART1_TX */
> + <STM32_PINMUX('A', 7, ANALOG)>; /* USART1_CTS_NSS */
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('C', 2, AF7)>; /* USART1_RTS */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <0>;
> + };
> + pins3 {
> + pinmux = <STM32_PINMUX('B', 0, AF4)>; /* USART1_RX */
> + bias-pull-up;
> + };
> + };
> +
> + usart1_sleep_pins_a: usart1-sleep-0 {
> + pins {
> + pinmux = <STM32_PINMUX('C', 0, ANALOG)>, /* USART1_TX */
> + <STM32_PINMUX('C', 2, ANALOG)>, /* USART1_RTS */
> + <STM32_PINMUX('A', 7, ANALOG)>, /* USART1_CTS_NSS */
> + <STM32_PINMUX('B', 0, ANALOG)>; /* USART1_RX */
> + };
> + };
> +
> + usart2_pins_a: usart2-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('H', 12, AF1)>, /* USART2_TX */
> + <STM32_PINMUX('D', 4, AF3)>; /* USART2_RTS */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <0>;
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('D', 15, AF1)>, /* USART2_RX */
> + <STM32_PINMUX('E', 11, AF2)>; /* USART2_CTS_NSS */
> + bias-disable;
> + };
> + };
> +
> + usart2_idle_pins_a: usart2-idle-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('H', 12, ANALOG)>, /* USART2_TX */
> + <STM32_PINMUX('E', 11, ANALOG)>; /* USART2_CTS_NSS */
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('D', 4, AF3)>; /* USART2_RTS */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <0>;
> + };
> + pins3 {
> + pinmux = <STM32_PINMUX('D', 15, AF1)>; /* USART2_RX */
> + bias-disable;
> + };
> + };
> +
> + usart2_sleep_pins_a: usart2-sleep-0 {
> + pins {
> + pinmux = <STM32_PINMUX('H', 12, ANALOG)>, /* USART2_TX */
> + <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */
> + <STM32_PINMUX('D', 15, ANALOG)>, /* USART2_RX */
> + <STM32_PINMUX('E', 11, ANALOG)>; /* USART2_CTS_NSS */
> + };
> + };
> };
> diff --git a/arch/arm/dts/stm32mp131.dtsi b/arch/arm/dts/stm32mp131.dtsi
> index d94ba2547267..d163c267e34c 100644
> --- a/arch/arm/dts/stm32mp131.dtsi
> +++ b/arch/arm/dts/stm32mp131.dtsi
> @@ -397,12 +397,42 @@
> status = "disabled";
> };
>
> + usart3: serial at 4000f000 {
> + compatible = "st,stm32h7-uart";
> + reg = <0x4000f000 0x400>;
> + interrupts-extended = <&exti 28 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&rcc USART3_K>;
> + resets = <&rcc USART3_R>;
> + wakeup-source;
> + dmas = <&dmamux1 45 0x400 0x5>,
> + <&dmamux1 46 0x400 0x1>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> uart4: serial at 40010000 {
> compatible = "st,stm32h7-uart";
> reg = <0x40010000 0x400>;
> - interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
> + interrupts-extended = <&exti 30 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&rcc UART4_K>;
> resets = <&rcc UART4_R>;
> + wakeup-source;
> + dmas = <&dmamux1 63 0x400 0x5>,
> + <&dmamux1 64 0x400 0x1>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> + uart5: serial at 40011000 {
> + compatible = "st,stm32h7-uart";
> + reg = <0x40011000 0x400>;
> + interrupts-extended = <&exti 31 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&rcc UART5_K>;
> + resets = <&rcc UART5_R>;
> + wakeup-source;
> + dmas = <&dmamux1 65 0x400 0x5>,
> + <&dmamux1 66 0x400 0x1>;
> + dma-names = "rx", "tx";
> status = "disabled";
> };
>
> @@ -442,6 +472,32 @@
> status = "disabled";
> };
>
> + uart7: serial at 40018000 {
> + compatible = "st,stm32h7-uart";
> + reg = <0x40018000 0x400>;
> + interrupts-extended = <&exti 32 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&rcc UART7_K>;
> + resets = <&rcc UART7_R>;
> + wakeup-source;
> + dmas = <&dmamux1 79 0x400 0x5>,
> + <&dmamux1 80 0x400 0x1>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> + uart8: serial at 40019000 {
> + compatible = "st,stm32h7-uart";
> + reg = <0x40019000 0x400>;
> + interrupts-extended = <&exti 33 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&rcc UART8_K>;
> + resets = <&rcc UART8_R>;
> + wakeup-source;
> + dmas = <&dmamux1 81 0x400 0x5>,
> + <&dmamux1 82 0x400 0x1>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> timers1: timer at 44000000 {
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -524,6 +580,19 @@
> };
> };
>
> + usart6: serial at 44003000 {
> + compatible = "st,stm32h7-uart";
> + reg = <0x44003000 0x400>;
> + interrupts-extended = <&exti 29 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&rcc USART6_K>;
> + resets = <&rcc USART6_R>;
> + wakeup-source;
> + dmas = <&dmamux1 71 0x400 0x5>,
> + <&dmamux1 72 0x400 0x1>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> i2s1: audio-controller at 44004000 {
> compatible = "st,stm32h7-i2s";
> reg = <0x44004000 0x400>;
> @@ -748,6 +817,32 @@
> status = "disabled";
> };
>
> + usart1: serial at 4c000000 {
> + compatible = "st,stm32h7-uart";
> + reg = <0x4c000000 0x400>;
> + interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&rcc USART1_K>;
> + resets = <&rcc USART1_R>;
> + wakeup-source;
> + dmas = <&dmamux1 41 0x400 0x5>,
> + <&dmamux1 42 0x400 0x1>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> + usart2: serial at 4c001000 {
> + compatible = "st,stm32h7-uart";
> + reg = <0x4c001000 0x400>;
> + interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&rcc USART2_K>;
> + resets = <&rcc USART2_R>;
> + wakeup-source;
> + dmas = <&dmamux1 43 0x400 0x5>,
> + <&dmamux1 44 0x400 0x1>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> i2s4: audio-controller at 4c002000 {
> compatible = "st,stm32h7-i2s";
> reg = <0x4c002000 0x400>;
> @@ -1001,8 +1096,6 @@
> reg = <0x50000000 0x1000>;
> #clock-cells = <1>;
> #reset-cells = <1>;
> - interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> -
> clock-names = "hse", "hsi", "csi", "lse", "lsi";
> clocks = <&scmi_clk CK_SCMI_HSE>,
> <&scmi_clk CK_SCMI_HSI>,
> diff --git a/arch/arm/dts/stm32mp135f-dk.dts b/arch/arm/dts/stm32mp135f-dk.dts
> index c40686cb2b9a..f0900ca672b5 100644
> --- a/arch/arm/dts/stm32mp135f-dk.dts
> +++ b/arch/arm/dts/stm32mp135f-dk.dts
> @@ -19,6 +19,13 @@
>
> aliases {
> serial0 = &uart4;
> + serial1 = &usart1;
> + serial2 = &uart8;
> + serial3 = &usart2;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> };
>
> memory at c0000000 {
> @@ -267,8 +274,41 @@
> };
>
> &uart4 {
> - pinctrl-names = "default";
> + pinctrl-names = "default", "sleep", "idle";
> pinctrl-0 = <&uart4_pins_a>;
> + pinctrl-1 = <&uart4_sleep_pins_a>;
> + pinctrl-2 = <&uart4_idle_pins_a>;
> + /delete-property/dmas;
> + /delete-property/dma-names;
> + status = "okay";
> +};
> +
> +&uart8 {
> + pinctrl-names = "default", "sleep", "idle";
> + pinctrl-0 = <&uart8_pins_a>;
> + pinctrl-1 = <&uart8_sleep_pins_a>;
> + pinctrl-2 = <&uart8_idle_pins_a>;
> + /delete-property/dmas;
> + /delete-property/dma-names;
> + status = "disabled";
> +};
> +
> +&usart1 {
> + pinctrl-names = "default", "sleep", "idle";
> + pinctrl-0 = <&usart1_pins_a>;
> + pinctrl-1 = <&usart1_sleep_pins_a>;
> + pinctrl-2 = <&usart1_idle_pins_a>;
> + uart-has-rtscts;
> + status = "disabled";
> +};
> +
> +/* Bluetooth */
> +&usart2 {
> + pinctrl-names = "default", "sleep", "idle";
> + pinctrl-0 = <&usart2_pins_a>;
> + pinctrl-1 = <&usart2_sleep_pins_a>;
> + pinctrl-2 = <&usart2_idle_pins_a>;
> + uart-has-rtscts;
> status = "okay";
> };
>
> diff --git a/arch/arm/dts/stm32mp15-pinctrl.dtsi b/arch/arm/dts/stm32mp15-pinctrl.dtsi
> index a9d2bec99014..e86d989dd351 100644
> --- a/arch/arm/dts/stm32mp15-pinctrl.dtsi
> +++ b/arch/arm/dts/stm32mp15-pinctrl.dtsi
> @@ -1880,6 +1880,21 @@
> };
> };
>
> + spi1_pins_b: spi1-1 {
> + pins1 {
> + pinmux = <STM32_PINMUX('A', 5, AF5)>, /* SPI1_SCK */
> + <STM32_PINMUX('B', 5, AF5)>; /* SPI1_MOSI */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <1>;
> + };
> +
> + pins2 {
> + pinmux = <STM32_PINMUX('A', 6, AF5)>; /* SPI1_MISO */
> + bias-disable;
> + };
> + };
> +
> spi2_pins_a: spi2-0 {
> pins1 {
> pinmux = <STM32_PINMUX('B', 10, AF5)>, /* SPI2_SCK */
> @@ -2163,7 +2178,7 @@
> <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */
> bias-disable;
> drive-push-pull;
> - slew-rate = <3>;
> + slew-rate = <0>;
> };
> pins2 {
> pinmux = <STM32_PINMUX('D', 6, AF7)>, /* USART2_RX */
> @@ -2181,7 +2196,7 @@
> pinmux = <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */
> bias-disable;
> drive-push-pull;
> - slew-rate = <3>;
> + slew-rate = <0>;
> };
> pins3 {
> pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */
> @@ -2448,19 +2463,4 @@
> bias-disable;
> };
> };
> -
> - spi1_pins_b: spi1-1 {
> - pins1 {
> - pinmux = <STM32_PINMUX('A', 5, AF5)>, /* SPI1_SCK */
> - <STM32_PINMUX('B', 5, AF5)>; /* SPI1_MOSI */
> - bias-disable;
> - drive-push-pull;
> - slew-rate = <1>;
> - };
> -
> - pins2 {
> - pinmux = <STM32_PINMUX('A', 6, AF5)>; /* SPI1_MISO */
> - bias-disable;
> - };
> - };
> };
> diff --git a/arch/arm/dts/stm32mp151.dtsi b/arch/arm/dts/stm32mp151.dtsi
> index b3baacbb2694..21d11be328c0 100644
> --- a/arch/arm/dts/stm32mp151.dtsi
> +++ b/arch/arm/dts/stm32mp151.dtsi
> @@ -1148,8 +1148,8 @@
> usbotg_hs: usb-otg at 49000000 {
> compatible = "st,stm32mp15-hsotg", "snps,dwc2";
> reg = <0x49000000 0x10000>;
> - clocks = <&rcc USBO_K>;
> - clock-names = "otg";
> + clocks = <&rcc USBO_K>, <&usbphyc>;
> + clock-names = "otg", "utmi";
> resets = <&rcc USBO_R>;
> reset-names = "dwc2";
> interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> diff --git a/arch/arm/dts/stm32mp157a-dk1.dts b/arch/arm/dts/stm32mp157a-dk1.dts
> index 4c8be9c8eb20..0da3667ab1e0 100644
> --- a/arch/arm/dts/stm32mp157a-dk1.dts
> +++ b/arch/arm/dts/stm32mp157a-dk1.dts
> @@ -17,9 +17,6 @@
>
> aliases {
> ethernet0 = ðernet0;
> - serial0 = &uart4;
> - serial1 = &usart3;
> - serial2 = &uart7;
> };
>
> chosen {
> diff --git a/arch/arm/dts/stm32mp157c-dk2.dts b/arch/arm/dts/stm32mp157c-dk2.dts
> index 2bc92ef3aeb9..ab13e340f4ef 100644
> --- a/arch/arm/dts/stm32mp157c-dk2.dts
> +++ b/arch/arm/dts/stm32mp157c-dk2.dts
> @@ -18,9 +18,6 @@
>
> aliases {
> ethernet0 = ðernet0;
> - serial0 = &uart4;
> - serial1 = &usart3;
> - serial2 = &uart7;
> serial3 = &usart2;
> };
>
> diff --git a/arch/arm/dts/stm32mp157c-ed1.dts b/arch/arm/dts/stm32mp157c-ed1.dts
> index fe5c8f25cecd..3541a17dceb9 100644
> --- a/arch/arm/dts/stm32mp157c-ed1.dts
> +++ b/arch/arm/dts/stm32mp157c-ed1.dts
> @@ -16,6 +16,10 @@
> model = "STMicroelectronics STM32MP157C eval daughter";
> compatible = "st,stm32mp157c-ed1", "st,stm32mp157";
>
> + aliases {
> + serial0 = &uart4;
> + };
> +
> chosen {
> stdout-path = "serial0:115200n8";
> };
> @@ -65,15 +69,6 @@
> reg = <0x38000000 0x10000>;
> no-map;
> };
> -
> - gpu_reserved: gpu at e8000000 {
> - reg = <0xe8000000 0x8000000>;
> - no-map;
> - };
> - };
> -
> - aliases {
> - serial0 = &uart4;
> };
>
> sd_switch: regulator-sd_switch {
> @@ -148,10 +143,6 @@
> status = "okay";
> };
>
> -&gpu {
> - contiguous-area = <&gpu_reserved>;
> -};
> -
> &hash1 {
> status = "okay";
> };
> diff --git a/arch/arm/dts/stm32mp157c-ev1.dts b/arch/arm/dts/stm32mp157c-ev1.dts
> index 542226cfcfdf..ba8e9d9a42fa 100644
> --- a/arch/arm/dts/stm32mp157c-ev1.dts
> +++ b/arch/arm/dts/stm32mp157c-ev1.dts
> @@ -14,16 +14,15 @@
> model = "STMicroelectronics STM32MP157C eval daughter on eval mother";
> compatible = "st,stm32mp157c-ev1", "st,stm32mp157c-ed1", "st,stm32mp157";
>
> - chosen {
> - stdout-path = "serial0:115200n8";
> - };
> -
> aliases {
> - serial0 = &uart4;
> serial1 = &usart3;
> ethernet0 = ðernet0;
> };
>
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> clocks {
> clk_ext_camera: clk-ext-camera {
> #clock-cells = <0>;
> diff --git a/arch/arm/dts/stm32mp15xx-dkx.dtsi b/arch/arm/dts/stm32mp15xx-dkx.dtsi
> index 49b3e768c898..f4de6c0b7587 100644
> --- a/arch/arm/dts/stm32mp15xx-dkx.dtsi
> +++ b/arch/arm/dts/stm32mp15xx-dkx.dtsi
> @@ -8,6 +8,12 @@
> #include <dt-bindings/mfd/st,stpmic1.h>
>
> / {
> + aliases {
> + serial0 = &uart4;
> + serial1 = &usart3;
> + serial2 = &uart7;
> + };
> +
> memory at c0000000 {
> device_type = "memory";
> reg = <0xc0000000 0x20000000>;
> @@ -53,11 +59,6 @@
> reg = <0x38000000 0x10000>;
> no-map;
> };
> -
> - gpu_reserved: gpu at d4000000 {
> - reg = <0xd4000000 0x4000000>;
> - no-map;
> - };
> };
>
> led {
> @@ -159,10 +160,6 @@
> };
> };
>
> -&gpu {
> - contiguous-area = <&gpu_reserved>;
> -};
> -
> &hash1 {
> status = "okay";
> };
Reviewed-by: Patrice Chotard <patrice.chotard at foss.st.com>
Thanks
Patrice
More information about the U-Boot
mailing list