[PATCH 1/5] board: rockchip: Add Pine64 Quartz64-A Board

[Christopher Obbard]

Hi Jonas,

On Sun, 2023-07-23 at 15:04 +0000, Jonas Karlman wrote:
> On 2023-07-23 16:55, Jonas Karlman wrote:
> > The Pine64 Quartz64 Model A is a single-board computer based on the
> > Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
> > CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
> > 20 pin GPIO header.
> > 
> > Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
> > - SD-card boot
> > - eMMC boot
> > - PCIe/NVMe/AHCI
> > - USB host
> > 
> > Device tree is imported from linux v6.4.
> > 
> > Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas at gmail.com>
> > Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas at gmail.com>
> > Signed-off-by: Jonas Karlman <jonas at kwiboo.se>
> > ---
> 
> [...]
> 
> Boot log with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and
> BL31=rk3568_bl31_v1.43.elf:
> 
> [...]
> 
> U-Boot 2023.07 (Jul 23 2023 - 12:42:18 +0000)
> 
> Model: Pine64 RK3566 Quartz64-A Board
> DRAM:  8 GiB (effective 7.7 GiB)
> PMIC:  RK8170 (on=0x10, off=0x00)
> Core:  321 devices, 27 uclasses, devicetree: separate
> MMC:   rockchip_sdhci_probe clk set rate fail!
> mmc at fe2b0000: 1, mmc at fe2c0000: 2, mmc at fe310000: 0
> Loading Environment from nowhere... OK
> In:    serial at fe660000
> Out:   serial at fe660000
> Err:   serial at fe660000
> Model: Pine64 RK3566 Quartz64-A Board
> Net:   No ethernet found.
> 
> Hit any key to stop autoboot:  0
> =>


I just tried booting U-Boot v2023.10-rc2 with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf, on my Quartz64-A but it fails during
loading of some parts. I removed the output of the RK TPL from my logs as there were no errors.

This is when booting from eMMC.

I also tried building your branch from https://github.com/Kwiboo/u-boot-rockchip/tree/rk3568-2023.10 and 


The full build commands:

export ROCKCHIP_TPL=rkbin/bin/rk35/rk3566_ddr_1056MHz_v1.17.bin
export BL31=rkbin/bin/rk35/rk3568_bl31_v1.43.elf
make quartz64-a-rk3566_defconfig
make -j16

rkdeveloptool db rk356x_spl_loader_v1.13.112.bin
rkdeveloptool wl 64 u-boot-rockchip.bin

Boot log (v2023.10-rc2):

U-Boot SPL 2023.10-rc2 (Aug 08 2023 - 14:02:34 +0100)
rockchip_sdhci_probe clk set rate fail!
Trying to boot from MMC1
spl: mmc init failed with error: -110
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 0 (ret = -5)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###


Boot log (your branch):

U-Boot SPL 2023.10-rc1-00368-g16cb31d427 (Aug 08 2023 - 15:17:35 +0100)
Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###


Thanks!

Chris