[PATCH v2 0/4] malloc: Reduce size by initializing data at runtime

[Sean Anderson]

In my efforts to get SPL to fit into flash after some changes I made, I
noticed that av_ is one of the largest variables in SPL. As it turns
out, we can generate it at runtime, and the code is already there. This
has the potential to save 1-2k across the board, for some (very) minor
boot time increase.

To measure the boot time difference, I applied the following patch:

---
 common/board_r.c | 5 +++++
 common/spl/spl.c | 4 ++++
 2 files changed, 9 insertions(+)

diff --git a/common/board_r.c b/common/board_r.c
index 58a5986aa54..ca624b20d46 100644
--- a/common/board_r.c
+++ b/common/board_r.c
@@ -194,6 +194,7 @@ static int initr_barrier(void)
 	return 0;
 }

+static ulong malloc_begin, malloc_end;
 static int initr_malloc(void)
 {
 	ulong malloc_start;
@@ -208,8 +209,10 @@ static int initr_malloc(void)
 	 * reserve_noncached().
 	 */
 	malloc_start = gd->relocaddr - TOTAL_MALLOC_LEN;
+	malloc_begin = timer_get_boot_us();
 	mem_malloc_init((ulong)map_sysmem(malloc_start, TOTAL_MALLOC_LEN),
 			TOTAL_MALLOC_LEN);
+	malloc_end = timer_get_boot_us();
 	gd->flags |= GD_FLG_FULL_MALLOC_INIT;
 	return 0;
 }
@@ -570,6 +573,8 @@ static int dm_announce(void)

 static int run_main_loop(void)
 {
+	printf("malloc_init took %luus (%lu %lu)\n", malloc_end - malloc_begin,
+	       malloc_begin, malloc_end);
 #ifdef CONFIG_SANDBOX
 	sandbox_main_loop_init();
 #endif
diff --git a/common/spl/spl.c b/common/spl/spl.c
index d74acec10b5..b34d1f4b4e6 100644
--- a/common/spl/spl.c
+++ b/common/spl/spl.c
@@ -755,7 +755,9 @@ void board_init_r(gd_t *dummy1, ulong dummy2)
 	spl_set_bd();

 #if defined(CONFIG_SYS_SPL_MALLOC)
+	ulong malloc_begin = timer_get_boot_us();
 	mem_malloc_init(SYS_SPL_MALLOC_START, CONFIG_SYS_SPL_MALLOC_SIZE);
+	ulong malloc_end = timer_get_boot_us();
 	gd->flags |= GD_FLG_FULL_MALLOC_INIT;
 #endif
 	if (!(gd->flags & GD_FLG_SPL_INIT)) {
@@ -817,6 +819,8 @@ void board_init_r(gd_t *dummy1, ulong dummy2)
 	spl_image.boot_device = BOOT_DEVICE_NONE;
 	board_boot_order(spl_boot_list);

+	printf("malloc_init took %luus (%lu %lu)\n", malloc_end - malloc_begin,
+	       malloc_begin, malloc_end);
 	ret = boot_from_devices(&spl_image, spl_boot_list,
 				ARRAY_SIZE(spl_boot_list));
 	if (ret) {
--
2.25.1

I found that MALLOC_CLEAR_ON_INIT dominated the mem_malloc_init time
(taking around 150 ms in SPL on my board). After disabling it, I found
that MALLOC_RUNTIME_INIT took around 5 us on average.

Changes in v2:
- Only mark malloc initialized after mem_malloc_init
- Fix cALLOc condition

Sean Anderson (4):
  common: Only mark malloc initialized after mem_malloc_init
  malloc: Don't use ifdefs for SYS_MALLOC_DEFAULT_TO_INIT
  malloc: Don't statically initialize av_ if using malloc_init
  malloc: Enable SYS_MALLOC_RUNTIME_INIT by default in SPL

 Kconfig           | 27 +++++++++++++++++----------
 common/board_r.c  |  3 ++-
 common/dlmalloc.c | 16 ++++++++--------
 3 files changed, 27 insertions(+), 19 deletions(-)

-- 
2.25.1