[PATCH v2 1/3] configs: layerscape: delete defconfigs using legacy PPA secure FW (part1)
laurentiu.tudor at nxp.com
laurentiu.tudor at nxp.com
Tue Aug 22 17:03:32 CEST 2023
From: Laurentiu Tudor <laurentiu.tudor at nxp.com>
PPA was a secure firmware developed in-house which is no longer
supported and replaced by TF-A quite some years ago. This makes
the defconfigs that make use of PPA obsolete, so remove them.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor at nxp.com>
---
configs/ls1012a2g5rdb_qspi_defconfig | 69 ---------
configs/ls1012afrdm_qspi_defconfig | 67 ---------
.../ls1012afrwy_qspi_SECURE_BOOT_defconfig | 72 ---------
configs/ls1012afrwy_qspi_defconfig | 72 ---------
configs/ls1012aqds_qspi_defconfig | 95 ------------
configs/ls1012ardb_qspi_SECURE_BOOT_defconfig | 77 ----------
configs/ls1012ardb_qspi_defconfig | 77 ----------
configs/ls1043aqds_defconfig | 107 --------------
configs/ls1043aqds_lpuart_defconfig | 109 --------------
configs/ls1043aqds_nand_defconfig | 138 ------------------
configs/ls1043aqds_nor_ddr3_defconfig | 108 --------------
configs/ls1043aqds_qspi_defconfig | 98 -------------
configs/ls1043aqds_sdcard_ifc_defconfig | 135 -----------------
configs/ls1043aqds_sdcard_qspi_defconfig | 124 ----------------
configs/ls1043ardb_SECURE_BOOT_defconfig | 99 -------------
configs/ls1043ardb_defconfig | 100 -------------
configs/ls1043ardb_nand_SECURE_BOOT_defconfig | 124 ----------------
configs/ls1043ardb_nand_defconfig | 128 ----------------
.../ls1043ardb_sdcard_SECURE_BOOT_defconfig | 124 ----------------
configs/ls1043ardb_sdcard_defconfig | 126 ----------------
configs/ls2080aqds_SECURE_BOOT_defconfig | 108 --------------
configs/ls2080aqds_defconfig | 109 --------------
configs/ls2080aqds_sdcard_defconfig | 116 ---------------
configs/ls2080ardb_SECURE_BOOT_defconfig | 107 --------------
configs/ls2080ardb_defconfig | 108 --------------
25 files changed, 2597 deletions(-)
delete mode 100644 configs/ls1012a2g5rdb_qspi_defconfig
delete mode 100644 configs/ls1012afrdm_qspi_defconfig
delete mode 100644 configs/ls1012afrwy_qspi_SECURE_BOOT_defconfig
delete mode 100644 configs/ls1012afrwy_qspi_defconfig
delete mode 100644 configs/ls1012aqds_qspi_defconfig
delete mode 100644 configs/ls1012ardb_qspi_SECURE_BOOT_defconfig
delete mode 100644 configs/ls1012ardb_qspi_defconfig
delete mode 100644 configs/ls1043aqds_defconfig
delete mode 100644 configs/ls1043aqds_lpuart_defconfig
delete mode 100644 configs/ls1043aqds_nand_defconfig
delete mode 100644 configs/ls1043aqds_nor_ddr3_defconfig
delete mode 100644 configs/ls1043aqds_qspi_defconfig
delete mode 100644 configs/ls1043aqds_sdcard_ifc_defconfig
delete mode 100644 configs/ls1043aqds_sdcard_qspi_defconfig
delete mode 100644 configs/ls1043ardb_SECURE_BOOT_defconfig
delete mode 100644 configs/ls1043ardb_defconfig
delete mode 100644 configs/ls1043ardb_nand_SECURE_BOOT_defconfig
delete mode 100644 configs/ls1043ardb_nand_defconfig
delete mode 100644 configs/ls1043ardb_sdcard_SECURE_BOOT_defconfig
delete mode 100644 configs/ls1043ardb_sdcard_defconfig
delete mode 100644 configs/ls2080aqds_SECURE_BOOT_defconfig
delete mode 100644 configs/ls2080aqds_defconfig
delete mode 100644 configs/ls2080aqds_sdcard_defconfig
delete mode 100644 configs/ls2080ardb_SECURE_BOOT_defconfig
delete mode 100644 configs/ls2080ardb_defconfig
diff --git a/configs/ls1012a2g5rdb_qspi_defconfig b/configs/ls1012a2g5rdb_qspi_defconfig
deleted file mode 100644
index 72b590a73b4c..000000000000
--- a/configs/ls1012a2g5rdb_qspi_defconfig
+++ /dev/null
@@ -1,69 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1012A2G5RDB=y
-CONFIG_TEXT_BASE=0x40100000
-CONFIG_SYS_MALLOC_LEN=0x500000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x300000
-CONFIG_ENV_SECT_SIZE=0x40000
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-2g5rdb"
-CONFIG_FSL_LS_PPA=y
-CONFIG_QSPI_AHB_INIT=y
-CONFIG_AHCI=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x9fffffff
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_QSPI_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000"
-CONFIG_BOOTCOMMAND="run distro_bootcmd; run qspi_bootcmd; env exists secureboot && esbc_halt;"
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMINFO=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_CACHE=y
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SATA=y
-CONFIG_SCSI_AHCI=y
-CONFIG_SATA_CEVA=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_DM_SPI_FLASH=y
-# CONFIG_SPI_FLASH_BAR is not set
-CONFIG_SPI_FLASH_SPANSION=y
-# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
-CONFIG_FSL_PFE=y
-CONFIG_DM_RTC=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_FSL_QSPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
diff --git a/configs/ls1012afrdm_qspi_defconfig b/configs/ls1012afrdm_qspi_defconfig
deleted file mode 100644
index 7e12f6ef546b..000000000000
--- a/configs/ls1012afrdm_qspi_defconfig
+++ /dev/null
@@ -1,67 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1012AFRDM=y
-CONFIG_TEXT_BASE=0x40100000
-CONFIG_SYS_MALLOC_LEN=0x500000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x300000
-CONFIG_ENV_SECT_SIZE=0x40000
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-frdm"
-CONFIG_FSL_LS_PPA=y
-CONFIG_QSPI_AHB_INIT=y
-CONFIG_PCI=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x9fffffff
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_QSPI_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000"
-CONFIG_BOOTCOMMAND="run distro_bootcmd;run qspi_bootcmd"
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMINFO=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_CACHE=y
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_DM_SPI_FLASH=y
-# CONFIG_SPI_FLASH_BAR is not set
-CONFIG_SPI_FLASH_SPANSION=y
-# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
-CONFIG_FSL_PFE=y
-CONFIG_E1000=y
-CONFIG_NVME_PCI=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_DM_RTC=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_FSL_QSPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
diff --git a/configs/ls1012afrwy_qspi_SECURE_BOOT_defconfig b/configs/ls1012afrwy_qspi_SECURE_BOOT_defconfig
deleted file mode 100644
index 4e5079dcc492..000000000000
--- a/configs/ls1012afrwy_qspi_SECURE_BOOT_defconfig
+++ /dev/null
@@ -1,72 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1012AFRWY=y
-CONFIG_TEXT_BASE=0x40100000
-CONFIG_SYS_MALLOC_LEN=0x500000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-frwy"
-CONFIG_FSL_LS_PPA=y
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_NXP_ESBC=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x9fffffff
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_QSPI_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000"
-CONFIG_BOOTCOMMAND="run distro_bootcmd; run sd_bootcmd; env exists secureboot && esbc_halt;"
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMINFO=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_CACHE=y
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_FSL_SEC_MON_BE=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_DM_SPI_FLASH=y
-# CONFIG_SPI_FLASH_BAR is not set
-CONFIG_SPI_FLASH_WINBOND=y
-CONFIG_FSL_PFE=y
-CONFIG_E1000=y
-CONFIG_NVME_PCI=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_DM_RTC=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_FSL_QSPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
-CONFIG_RSA=y
-CONFIG_RSA_SOFTWARE_EXP=y
diff --git a/configs/ls1012afrwy_qspi_defconfig b/configs/ls1012afrwy_qspi_defconfig
deleted file mode 100644
index b944f803f70c..000000000000
--- a/configs/ls1012afrwy_qspi_defconfig
+++ /dev/null
@@ -1,72 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1012AFRWY=y
-CONFIG_TEXT_BASE=0x40100000
-CONFIG_SYS_MALLOC_LEN=0x500000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x1D0000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-frwy"
-CONFIG_FSL_LS_PPA=y
-CONFIG_ENV_ADDR=0x401D0000
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x9fffffff
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_QSPI_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000"
-CONFIG_BOOTCOMMAND="run distro_bootcmd; run sd_bootcmd; env exists secureboot && esbc_halt;"
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMINFO=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_CACHE=y
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SPI_FLASH_WINBOND=y
-CONFIG_FSL_PFE=y
-CONFIG_E1000=y
-CONFIG_NVME_PCI=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_DM_RTC=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
diff --git a/configs/ls1012aqds_qspi_defconfig b/configs/ls1012aqds_qspi_defconfig
deleted file mode 100644
index 34bdb1abafc7..000000000000
--- a/configs/ls1012aqds_qspi_defconfig
+++ /dev/null
@@ -1,95 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1012AQDS=y
-CONFIG_TEXT_BASE=0x40100000
-CONFIG_SYS_MALLOC_LEN=0x500000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_SF_DEFAULT_SPEED=10000000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x300000
-CONFIG_ENV_SECT_SIZE=0x40000
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-qds"
-CONFIG_FSL_LS_PPA=y
-CONFIG_QSPI_AHB_INIT=y
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_FSL_QIXIS=y
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x9fffffff
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_QSPI_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000"
-CONFIG_BOOTCOMMAND="run distro_bootcmd; run qspi_bootcmd; env exists secureboot && esbc_halt;"
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_MISC_INIT_R=y
-CONFIG_ID_EEPROM=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_MEMINFO=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_SPI=y
-CONFIG_DEFAULT_SPI_BUS=1
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_CACHE=y
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_ENV_SPI_BUS=0
-CONFIG_ENV_SPI_MAX_HZ=1000000
-CONFIG_ENV_SPI_MODE=0x03
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SATA=y
-CONFIG_SCSI_AHCI=y
-CONFIG_SATA_CEVA=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x57
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SF_DEFAULT_BUS=1
-# CONFIG_SPI_FLASH_BAR is not set
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
-CONFIG_FSL_PFE=y
-CONFIG_E1000=y
-CONFIG_NVME_PCI=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_DM_RTC=y
-CONFIG_RTC_PCF8563=y
-CONFIG_SCSI=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_FSL_DSPI=y
-CONFIG_FSL_QSPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
diff --git a/configs/ls1012ardb_qspi_SECURE_BOOT_defconfig b/configs/ls1012ardb_qspi_SECURE_BOOT_defconfig
deleted file mode 100644
index dcd18b4eb8cc..000000000000
--- a/configs/ls1012ardb_qspi_SECURE_BOOT_defconfig
+++ /dev/null
@@ -1,77 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1012ARDB=y
-CONFIG_TEXT_BASE=0x40100000
-CONFIG_SYS_MALLOC_LEN=0x500000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-rdb"
-CONFIG_FSL_LS_PPA=y
-CONFIG_QSPI_AHB_INIT=y
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_NXP_ESBC=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x9fffffff
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_QSPI_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000"
-CONFIG_BOOTCOMMAND="run distro_bootcmd; run qspi_bootcmd; env exists secureboot && esbc_halt;"
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMINFO=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_CACHE=y
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_FSL_SEC_MON_BE=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_DM_SPI_FLASH=y
-# CONFIG_SPI_FLASH_BAR is not set
-CONFIG_SPI_FLASH_SPANSION=y
-# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
-CONFIG_E1000=y
-CONFIG_NVME_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_DM_RTC=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_FSL_DSPI=y
-CONFIG_FSL_QSPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
-CONFIG_RSA=y
-CONFIG_RSA_SOFTWARE_EXP=y
diff --git a/configs/ls1012ardb_qspi_defconfig b/configs/ls1012ardb_qspi_defconfig
deleted file mode 100644
index 10fe826f99a0..000000000000
--- a/configs/ls1012ardb_qspi_defconfig
+++ /dev/null
@@ -1,77 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1012ARDB=y
-CONFIG_TEXT_BASE=0x40100000
-CONFIG_SYS_MALLOC_LEN=0x500000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x300000
-CONFIG_ENV_SECT_SIZE=0x40000
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-rdb"
-CONFIG_FSL_LS_PPA=y
-CONFIG_QSPI_AHB_INIT=y
-CONFIG_ENV_ADDR=0x40300000
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x9fffffff
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_QSPI_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000"
-CONFIG_BOOTCOMMAND="run distro_bootcmd; run qspi_bootcmd; env exists secureboot && esbc_halt;"
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_MEMINFO=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_CACHE=y
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_DM_SPI_FLASH=y
-# CONFIG_SPI_FLASH_BAR is not set
-CONFIG_SPI_FLASH_SPANSION=y
-# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
-CONFIG_FSL_PFE=y
-CONFIG_E1000=y
-CONFIG_NVME_PCI=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_DM_RTC=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_FSL_DSPI=y
-CONFIG_FSL_QSPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
diff --git a/configs/ls1043aqds_defconfig b/configs/ls1043aqds_defconfig
deleted file mode 100644
index 18bf4bd8792c..000000000000
--- a/configs/ls1043aqds_defconfig
+++ /dev/null
@@ -1,107 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1043AQDS=y
-CONFIG_TEXT_BASE=0x60100000
-CONFIG_SYS_MALLOC_LEN=0x120000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_SYS_I2C_MXC_I2C1=y
-CONFIG_SYS_I2C_MXC_I2C2=y
-CONFIG_SYS_I2C_MXC_I2C3=y
-CONFIG_SYS_I2C_MXC_I2C4=y
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart"
-CONFIG_FSL_LS_PPA=y
-CONFIG_ENV_ADDR=0x60300000
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_PCIE2=y
-CONFIG_PCIE3=y
-CONFIG_FSL_USE_PCA9547_MUX=y
-CONFIG_VID=y
-CONFIG_VID_FLS_ENV="ls1043aqds_vdd_mv"
-CONFIG_VOL_MONITOR_INA220=y
-CONFIG_VOL_MONITOR_IR36021_SET=y
-CONFIG_FSL_QIXIS=y
-# CONFIG_QIXIS_I2C_ACCESS is not set
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x9fffffff
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_DYNAMIC_SYS_CLK_FREQ=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_ARCH_MISC_INIT=y
-CONFIG_MISC_INIT_R=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_MEMINFO=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_CACHE=y
-CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_FSL_CAAM=y
-CONFIG_DYNAMIC_DDR_CLK_FREQ=y
-CONFIG_DDR_ECC=y
-CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_SPL_SYS_I2C_LEGACY=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x57
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SF_DEFAULT_BUS=1
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_VITESSE=y
-CONFIG_E1000=y
-CONFIG_NVME_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
diff --git a/configs/ls1043aqds_lpuart_defconfig b/configs/ls1043aqds_lpuart_defconfig
deleted file mode 100644
index 9dcbe71ad0c1..000000000000
--- a/configs/ls1043aqds_lpuart_defconfig
+++ /dev/null
@@ -1,109 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1043AQDS=y
-CONFIG_TEXT_BASE=0x60100000
-CONFIG_SYS_MALLOC_LEN=0x120000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_SYS_I2C_MXC_I2C1=y
-CONFIG_SYS_I2C_MXC_I2C2=y
-CONFIG_SYS_I2C_MXC_I2C3=y
-CONFIG_SYS_I2C_MXC_I2C4=y
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-lpuart"
-CONFIG_FSL_LS_PPA=y
-CONFIG_ENV_ADDR=0x60300000
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_PCIE2=y
-CONFIG_PCIE3=y
-CONFIG_FSL_USE_PCA9547_MUX=y
-CONFIG_VID=y
-CONFIG_VID_FLS_ENV="ls1043aqds_vdd_mv"
-CONFIG_VOL_MONITOR_INA220=y
-CONFIG_VOL_MONITOR_IR36021_SET=y
-CONFIG_FSL_QIXIS=y
-# CONFIG_QIXIS_I2C_ACCESS is not set
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x9fffffff
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_DYNAMIC_SYS_CLK_FREQ=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_ARCH_MISC_INIT=y
-CONFIG_MISC_INIT_R=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_MEMINFO=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_CACHE=y
-CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_FSL_CAAM=y
-CONFIG_DYNAMIC_DDR_CLK_FREQ=y
-CONFIG_DDR_ECC=y
-CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_SPL_SYS_I2C_LEGACY=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x57
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SF_DEFAULT_BUS=1
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_VITESSE=y
-CONFIG_E1000=y
-CONFIG_NVME_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_DM_SCSI=y
-CONFIG_DM_SERIAL=y
-CONFIG_FSL_LPUART=y
-CONFIG_LPUART=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
diff --git a/configs/ls1043aqds_nand_defconfig b/configs/ls1043aqds_nand_defconfig
deleted file mode 100644
index e5f570a3b3c1..000000000000
--- a/configs/ls1043aqds_nand_defconfig
+++ /dev/null
@@ -1,138 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1043AQDS=y
-CONFIG_TEXT_BASE=0x82000000
-CONFIG_SYS_MALLOC_LEN=0x102000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x300000
-CONFIG_SYS_I2C_MXC_I2C1=y
-CONFIG_SYS_I2C_MXC_I2C2=y
-CONFIG_SYS_I2C_MXC_I2C3=y
-CONFIG_SYS_I2C_MXC_I2C4=y
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart"
-CONFIG_SPL_TEXT_BASE=0x10000000
-CONFIG_FSL_LS_PPA=y
-CONFIG_SYS_MONITOR_LEN=1048576
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_STACK=0x1001d000
-CONFIG_SPL=y
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_PCIE2=y
-CONFIG_PCIE3=y
-CONFIG_FSL_USE_PCA9547_MUX=y
-CONFIG_VID=y
-CONFIG_VID_FLS_ENV="ls1043aqds_vdd_mv"
-CONFIG_VOL_MONITOR_INA220=y
-CONFIG_VOL_MONITOR_IR36021_SET=y
-CONFIG_FSL_QIXIS=y
-# CONFIG_QIXIS_I2C_ACCESS is not set
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x9fffffff
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_DYNAMIC_SYS_CLK_FREQ=y
-CONFIG_RAMBOOT_PBL=y
-CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043aqds/ls1043aqds_pbi.cfg"
-CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043aqds/ls1043aqds_rcw_nand.cfg"
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_NAND_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_ARCH_MISC_INIT=y
-CONFIG_MISC_INIT_R=y
-CONFIG_SPL_MAX_SIZE=0x1a000
-CONFIG_SPL_PAD_TO=0x20000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x80100000
-CONFIG_SPL_BSS_MAX_SIZE=0x80000
-CONFIG_SPL_FSL_PBL=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y
-CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x80200000
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xf0
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C=y
-CONFIG_SPL_MPC8XXX_INIT_DDR=y
-CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_SPL_WATCHDOG=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_MEMINFO=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_CACHE=y
-CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_SPL_EFI_PARTITION is not set
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_FSL_CAAM=y
-CONFIG_DYNAMIC_DDR_CLK_FREQ=y
-CONFIG_DDR_ECC=y
-CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_SPL_SYS_I2C_LEGACY=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x57
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
-CONFIG_SYS_NAND_U_BOOT_OFFS=0x20000
-CONFIG_SF_DEFAULT_BUS=1
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_VITESSE=y
-CONFIG_E1000=y
-CONFIG_NVME_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
diff --git a/configs/ls1043aqds_nor_ddr3_defconfig b/configs/ls1043aqds_nor_ddr3_defconfig
deleted file mode 100644
index 67d8288abb00..000000000000
--- a/configs/ls1043aqds_nor_ddr3_defconfig
+++ /dev/null
@@ -1,108 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1043AQDS=y
-CONFIG_TEXT_BASE=0x60100000
-CONFIG_SYS_MALLOC_LEN=0x120000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_SYS_I2C_MXC_I2C1=y
-CONFIG_SYS_I2C_MXC_I2C2=y
-CONFIG_SYS_I2C_MXC_I2C3=y
-CONFIG_SYS_I2C_MXC_I2C4=y
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart"
-CONFIG_FSL_LS_PPA=y
-CONFIG_ENV_ADDR=0x60300000
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_PCIE2=y
-CONFIG_PCIE3=y
-CONFIG_FSL_USE_PCA9547_MUX=y
-CONFIG_VID=y
-CONFIG_VID_FLS_ENV="ls1043aqds_vdd_mv"
-CONFIG_VOL_MONITOR_INA220=y
-CONFIG_VOL_MONITOR_IR36021_SET=y
-CONFIG_FSL_QIXIS=y
-# CONFIG_QIXIS_I2C_ACCESS is not set
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x9fffffff
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_DYNAMIC_SYS_CLK_FREQ=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_ARCH_MISC_INIT=y
-CONFIG_MISC_INIT_R=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_MEMINFO=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_CACHE=y
-CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_FSL_CAAM=y
-CONFIG_DYNAMIC_DDR_CLK_FREQ=y
-CONFIG_SYS_FSL_DDR3=y
-CONFIG_DDR_ECC=y
-CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_SPL_SYS_I2C_LEGACY=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x57
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SF_DEFAULT_BUS=1
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_VITESSE=y
-CONFIG_E1000=y
-CONFIG_NVME_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
diff --git a/configs/ls1043aqds_qspi_defconfig b/configs/ls1043aqds_qspi_defconfig
deleted file mode 100644
index fa0b47fde8c4..000000000000
--- a/configs/ls1043aqds_qspi_defconfig
+++ /dev/null
@@ -1,98 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1043AQDS=y
-CONFIG_TEXT_BASE=0x40100000
-CONFIG_SYS_MALLOC_LEN=0x102000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x300000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_SYS_I2C_MXC_I2C1=y
-CONFIG_SYS_I2C_MXC_I2C2=y
-CONFIG_SYS_I2C_MXC_I2C3=y
-CONFIG_SYS_I2C_MXC_I2C4=y
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart"
-CONFIG_FSL_LS_PPA=y
-CONFIG_ENV_ADDR=0x40300000
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_PCIE2=y
-CONFIG_PCIE3=y
-CONFIG_FSL_USE_PCA9547_MUX=y
-CONFIG_VID=y
-CONFIG_VID_FLS_ENV="ls1043aqds_vdd_mv"
-CONFIG_VOL_MONITOR_INA220=y
-CONFIG_VOL_MONITOR_IR36021_SET=y
-CONFIG_FSL_QIXIS=y
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x9fffffff
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_DYNAMIC_SYS_CLK_FREQ=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_QSPI_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_ARCH_MISC_INIT=y
-CONFIG_MISC_INIT_R=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_GREPENV=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_MEMINFO=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_CACHE=y
-CONFIG_MTDPARTS_DEFAULT="mtdparts=spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_FSL_CAAM=y
-CONFIG_DYNAMIC_DDR_CLK_FREQ=y
-CONFIG_DDR_ECC=y
-CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_SPL_SYS_I2C_LEGACY=y
-CONFIG_SYS_I2C_EARLY_INIT=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x57
-CONFIG_FSL_ESDHC=y
-# CONFIG_SPI_FLASH_BAR is not set
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_VITESSE=y
-CONFIG_E1000=y
-CONFIG_NVME_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_FSL_QSPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
diff --git a/configs/ls1043aqds_sdcard_ifc_defconfig b/configs/ls1043aqds_sdcard_ifc_defconfig
deleted file mode 100644
index 6cb961d33dcc..000000000000
--- a/configs/ls1043aqds_sdcard_ifc_defconfig
+++ /dev/null
@@ -1,135 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1043AQDS=y
-CONFIG_TEXT_BASE=0x82000000
-CONFIG_SYS_MALLOC_LEN=0x102000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x300000
-CONFIG_SYS_I2C_MXC_I2C1=y
-CONFIG_SYS_I2C_MXC_I2C2=y
-CONFIG_SYS_I2C_MXC_I2C3=y
-CONFIG_SYS_I2C_MXC_I2C4=y
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart"
-CONFIG_SPL_TEXT_BASE=0x10000000
-CONFIG_FSL_LS_PPA=y
-CONFIG_SYS_MONITOR_LEN=1048576
-CONFIG_SPL_MMC=y
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_STACK=0x1001e000
-CONFIG_SPL=y
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_PCIE2=y
-CONFIG_PCIE3=y
-CONFIG_FSL_USE_PCA9547_MUX=y
-CONFIG_VID=y
-CONFIG_VID_FLS_ENV="ls1043aqds_vdd_mv"
-CONFIG_VOL_MONITOR_INA220=y
-CONFIG_VOL_MONITOR_IR36021_SET=y
-CONFIG_FSL_QIXIS=y
-# CONFIG_QIXIS_I2C_ACCESS is not set
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x9fffffff
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_DYNAMIC_SYS_CLK_FREQ=y
-CONFIG_RAMBOOT_PBL=y
-CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043aqds/ls1043aqds_pbi.cfg"
-CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043aqds/ls1043aqds_rcw_sd_ifc.cfg"
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_SD_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_ARCH_MISC_INIT=y
-CONFIG_MISC_INIT_R=y
-CONFIG_SPL_MAX_SIZE=0x17000
-CONFIG_SPL_PAD_TO=0x1d000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x8f000000
-CONFIG_SPL_BSS_MAX_SIZE=0x80000
-CONFIG_SPL_FSL_PBL=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xf0
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C=y
-CONFIG_SPL_MPC8XXX_INIT_DDR=y
-CONFIG_SPL_WATCHDOG=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_MEMINFO=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_CACHE=y
-CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_SPL_EFI_PARTITION is not set
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_FSL_CAAM=y
-CONFIG_DYNAMIC_DDR_CLK_FREQ=y
-CONFIG_DDR_ECC=y
-CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_SPL_SYS_I2C_LEGACY=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x57
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SF_DEFAULT_BUS=1
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_VITESSE=y
-CONFIG_E1000=y
-CONFIG_NVME_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
diff --git a/configs/ls1043aqds_sdcard_qspi_defconfig b/configs/ls1043aqds_sdcard_qspi_defconfig
deleted file mode 100644
index 4e41508251da..000000000000
--- a/configs/ls1043aqds_sdcard_qspi_defconfig
+++ /dev/null
@@ -1,124 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1043AQDS=y
-CONFIG_TEXT_BASE=0x82000000
-CONFIG_SYS_MALLOC_LEN=0x102000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x300000
-CONFIG_SYS_I2C_MXC_I2C1=y
-CONFIG_SYS_I2C_MXC_I2C2=y
-CONFIG_SYS_I2C_MXC_I2C3=y
-CONFIG_SYS_I2C_MXC_I2C4=y
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart"
-CONFIG_SPL_TEXT_BASE=0x10000000
-CONFIG_FSL_LS_PPA=y
-CONFIG_SYS_MONITOR_LEN=1048576
-CONFIG_SPL_MMC=y
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_STACK=0x1001e000
-CONFIG_SPL=y
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_PCIE2=y
-CONFIG_PCIE3=y
-CONFIG_FSL_USE_PCA9547_MUX=y
-CONFIG_VID=y
-CONFIG_VID_FLS_ENV="ls1043aqds_vdd_mv"
-CONFIG_VOL_MONITOR_INA220=y
-CONFIG_VOL_MONITOR_IR36021_SET=y
-CONFIG_FSL_QIXIS=y
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x9fffffff
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_DYNAMIC_SYS_CLK_FREQ=y
-CONFIG_RAMBOOT_PBL=y
-CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043aqds/ls1043aqds_pbi.cfg"
-CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043aqds/ls1043aqds_rcw_sd_qspi.cfg"
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_SD_BOOT=y
-CONFIG_SD_BOOT_QSPI=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_ARCH_MISC_INIT=y
-CONFIG_MISC_INIT_R=y
-CONFIG_SPL_MAX_SIZE=0x17000
-CONFIG_SPL_PAD_TO=0x1d000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x8f000000
-CONFIG_SPL_BSS_MAX_SIZE=0x80000
-CONFIG_SPL_FSL_PBL=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xf0
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C=y
-CONFIG_SPL_MPC8XXX_INIT_DDR=y
-CONFIG_SPL_WATCHDOG=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_GREPENV=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_MEMINFO=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_CACHE=y
-CONFIG_MTDPARTS_DEFAULT="mtdparts=spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_SPL_EFI_PARTITION is not set
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_FSL_CAAM=y
-CONFIG_DYNAMIC_DDR_CLK_FREQ=y
-CONFIG_DDR_ECC=y
-CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_SPL_SYS_I2C_LEGACY=y
-CONFIG_SYS_I2C_EARLY_INIT=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x57
-CONFIG_FSL_ESDHC=y
-# CONFIG_SPI_FLASH_BAR is not set
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_VITESSE=y
-CONFIG_E1000=y
-CONFIG_NVME_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_FSL_QSPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
diff --git a/configs/ls1043ardb_SECURE_BOOT_defconfig b/configs/ls1043ardb_SECURE_BOOT_defconfig
deleted file mode 100644
index ea195d7c5041..000000000000
--- a/configs/ls1043ardb_SECURE_BOOT_defconfig
+++ /dev/null
@@ -1,99 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1043ARDB=y
-CONFIG_TEXT_BASE=0x60100000
-CONFIG_SYS_MALLOC_LEN=0x120000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x20000
-CONFIG_SYS_I2C_MXC_I2C1=y
-CONFIG_SYS_I2C_MXC_I2C2=y
-CONFIG_SYS_I2C_MXC_I2C3=y
-CONFIG_SYS_I2C_MXC_I2C4=y
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb"
-CONFIG_FSL_LS_PPA=y
-CONFIG_PCI=y
-CONFIG_OF_BOARD_FIXUP=y
-CONFIG_NXP_ESBC=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_PCIE2=y
-CONFIG_PCIE3=y
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-CONFIG_BOOTCOMMAND="run distro_bootcmd; run nor_bootcmd; env exists secureboot && esbc_halt;"
-CONFIG_MISC_INIT_R=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_IMLS=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_DM=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_CACHE=y
-CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_USE_ETHPRIME=y
-CONFIG_ETHPRIME="FM1 at DTSEC3"
-# CONFIG_DDR_SPD is not set
-CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
-CONFIG_SYS_DDR_RAW_TIMING=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_SPL_SYS_I2C_LEGACY=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_FSL_SEC_MON_BE=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x53
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SF_DEFAULT_BUS=1
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_VITESSE=y
-CONFIG_DM_MDIO=y
-CONFIG_PHY_GIGE=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_SYS_FMAN_FW_ADDR=0x60900000
-CONFIG_NVME_PCI=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_SYS_QE_FW_ADDR=0x60940000
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_SPECIFY_CONSOLE_INDEX=y
-CONFIG_DM_SERIAL=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
-CONFIG_RSA=y
-CONFIG_RSA_SOFTWARE_EXP=y
-CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
diff --git a/configs/ls1043ardb_defconfig b/configs/ls1043ardb_defconfig
deleted file mode 100644
index ae8600ffd958..000000000000
--- a/configs/ls1043ardb_defconfig
+++ /dev/null
@@ -1,100 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1043ARDB=y
-CONFIG_TEXT_BASE=0x60100000
-CONFIG_SYS_MALLOC_LEN=0x120000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_SYS_I2C_MXC_I2C1=y
-CONFIG_SYS_I2C_MXC_I2C2=y
-CONFIG_SYS_I2C_MXC_I2C3=y
-CONFIG_SYS_I2C_MXC_I2C4=y
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb"
-CONFIG_FSL_LS_PPA=y
-CONFIG_ENV_ADDR=0x60300000
-CONFIG_PCI=y
-CONFIG_OF_BOARD_FIXUP=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_PCIE2=y
-CONFIG_PCIE3=y
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-CONFIG_BOOTCOMMAND="run distro_bootcmd; run nor_bootcmd; env exists secureboot && esbc_halt;"
-CONFIG_ARCH_MISC_INIT=y
-CONFIG_MISC_INIT_R=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_IMLS=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_DM=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_CACHE=y
-CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_USE_ETHPRIME=y
-CONFIG_ETHPRIME="FM1 at DTSEC3"
-CONFIG_FSL_CAAM=y
-# CONFIG_DDR_SPD is not set
-CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
-CONFIG_SYS_DDR_RAW_TIMING=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_SPL_SYS_I2C_LEGACY=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x53
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SF_DEFAULT_BUS=1
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_VITESSE=y
-CONFIG_DM_MDIO=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_SYS_FMAN_FW_ADDR=0x60900000
-CONFIG_NVME_PCI=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_SYS_QE_FW_ADDR=0x60940000
-CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
-CONFIG_SPECIFY_CONSOLE_INDEX=y
-CONFIG_DM_SERIAL=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
-CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
diff --git a/configs/ls1043ardb_nand_SECURE_BOOT_defconfig b/configs/ls1043ardb_nand_SECURE_BOOT_defconfig
deleted file mode 100644
index d9ff0fd16a58..000000000000
--- a/configs/ls1043ardb_nand_SECURE_BOOT_defconfig
+++ /dev/null
@@ -1,124 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1043ARDB=y
-CONFIG_TEXT_BASE=0x82000000
-CONFIG_SYS_MALLOC_LEN=0x102000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb"
-CONFIG_SPL_TEXT_BASE=0x10000000
-CONFIG_FSL_LS_PPA=y
-CONFIG_SYS_MONITOR_LEN=1064960
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_STACK=0x1001d000
-CONFIG_SPL=y
-CONFIG_PCI=y
-CONFIG_OF_BOARD_FIXUP=y
-CONFIG_NXP_ESBC=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_PCIE2=y
-CONFIG_PCIE3=y
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_RAMBOOT_PBL=y
-CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043ardb/ls1043ardb_pbi.cfg"
-CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043ardb/ls1043ardb_rcw_nand.cfg"
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_NAND_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_MISC_INIT_R=y
-CONFIG_SPL_MAX_SIZE=0x1a000
-CONFIG_SPL_PAD_TO=0x20000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x80100000
-CONFIG_SPL_BSS_MAX_SIZE=0x80000
-CONFIG_SPL_FSL_PBL=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y
-CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x80200000
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xf0
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR=y
-CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_SPL_WATCHDOG=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_IMLS=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_DM=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_CACHE=y
-CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_SPL_EFI_PARTITION is not set
-CONFIG_OF_CONTROL=y
-CONFIG_SPL_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_USE_ETHPRIME=y
-CONFIG_ETHPRIME="FM1 at DTSEC3"
-CONFIG_SPL_DM=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_FSL_SEC_MON_BE=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x53
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
-CONFIG_SYS_NAND_U_BOOT_OFFS=0x20000
-CONFIG_SF_DEFAULT_BUS=1
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_VITESSE=y
-CONFIG_DM_MDIO=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_SYS_FMAN_FW_ADDR=0x900000
-CONFIG_NVME_PCI=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_SYS_QE_FMAN_FW_IN_NAND=y
-CONFIG_SPECIFY_CONSOLE_INDEX=y
-CONFIG_DM_SERIAL=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
-# CONFIG_SPL_USE_TINY_PRINTF is not set
-CONFIG_RSA=y
-CONFIG_SPL_RSA=y
-CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
diff --git a/configs/ls1043ardb_nand_defconfig b/configs/ls1043ardb_nand_defconfig
deleted file mode 100644
index ad118187432e..000000000000
--- a/configs/ls1043ardb_nand_defconfig
+++ /dev/null
@@ -1,128 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1043ARDB=y
-CONFIG_TEXT_BASE=0x82000000
-CONFIG_SYS_MALLOC_LEN=0x102000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x300000
-CONFIG_SYS_I2C_MXC_I2C1=y
-CONFIG_SYS_I2C_MXC_I2C2=y
-CONFIG_SYS_I2C_MXC_I2C3=y
-CONFIG_SYS_I2C_MXC_I2C4=y
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb"
-CONFIG_SPL_TEXT_BASE=0x10000000
-CONFIG_FSL_LS_PPA=y
-CONFIG_SYS_MONITOR_LEN=1048576
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_STACK=0x1001d000
-CONFIG_SPL=y
-CONFIG_PCI=y
-CONFIG_OF_BOARD_FIXUP=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_PCIE2=y
-CONFIG_PCIE3=y
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_RAMBOOT_PBL=y
-CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043ardb/ls1043ardb_pbi.cfg"
-CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043ardb/ls1043ardb_rcw_nand.cfg"
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_NAND_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_ARCH_MISC_INIT=y
-CONFIG_MISC_INIT_R=y
-CONFIG_SPL_MAX_SIZE=0x1a000
-CONFIG_SPL_PAD_TO=0x20000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x80100000
-CONFIG_SPL_BSS_MAX_SIZE=0x80000
-CONFIG_SPL_FSL_PBL=y
-CONFIG_SPL_BOARD_INIT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y
-CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x80200000
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xf0
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C=y
-CONFIG_SPL_MPC8XXX_INIT_DDR=y
-CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_SPL_WATCHDOG=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_IMLS=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_DM=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_CACHE=y
-CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_SPL_EFI_PARTITION is not set
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_USE_ETHPRIME=y
-CONFIG_ETHPRIME="FM1 at DTSEC3"
-CONFIG_FSL_CAAM=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_SPL_SYS_I2C_LEGACY=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x53
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
-CONFIG_SYS_NAND_U_BOOT_OFFS=0x20000
-CONFIG_SF_DEFAULT_BUS=1
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_VITESSE=y
-CONFIG_DM_MDIO=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_SYS_FMAN_FW_ADDR=0x900000
-CONFIG_NVME_PCI=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_SYS_QE_FMAN_FW_IN_NAND=y
-CONFIG_DM_SERIAL=y
-CONFIG_SPL_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
-# CONFIG_SPL_USE_TINY_PRINTF is not set
-CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
diff --git a/configs/ls1043ardb_sdcard_SECURE_BOOT_defconfig b/configs/ls1043ardb_sdcard_SECURE_BOOT_defconfig
deleted file mode 100644
index fe0dd04f1f90..000000000000
--- a/configs/ls1043ardb_sdcard_SECURE_BOOT_defconfig
+++ /dev/null
@@ -1,124 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1043ARDB=y
-CONFIG_TEXT_BASE=0x82000000
-CONFIG_SYS_MALLOC_LEN=0x102000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb"
-CONFIG_SPL_TEXT_BASE=0x10000000
-CONFIG_FSL_LS_PPA=y
-CONFIG_SYS_MONITOR_LEN=1064960
-CONFIG_SPL_MMC=y
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_STACK=0x1001e000
-CONFIG_SPL=y
-CONFIG_PCI=y
-CONFIG_OF_BOARD_FIXUP=y
-CONFIG_NXP_ESBC=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_PCIE2=y
-CONFIG_PCIE3=y
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_RAMBOOT_PBL=y
-CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043ardb/ls1043ardb_pbi.cfg"
-CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043ardb/ls1043ardb_rcw_sd.cfg"
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_SD_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-CONFIG_BOOTCOMMAND="run distro_bootcmd; run sd_bootcmd; env exists secureboot && esbc_halt;"
-CONFIG_MISC_INIT_R=y
-CONFIG_SPL_MAX_SIZE=0x17000
-CONFIG_SPL_PAD_TO=0x1d000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x8f000000
-CONFIG_SPL_BSS_MAX_SIZE=0x80000
-CONFIG_SPL_FSL_PBL=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x110
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR=y
-CONFIG_SPL_WATCHDOG=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_SPL=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_DM=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_CACHE=y
-CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_SPL_EFI_PARTITION is not set
-CONFIG_OF_CONTROL=y
-CONFIG_SPL_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_USE_ETHPRIME=y
-CONFIG_ETHPRIME="FM1 at DTSEC3"
-CONFIG_SPL_DM=y
-# CONFIG_SPL_BLK is not set
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_FSL_SEC_MON_BE=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x53
-# CONFIG_SPL_DM_MMC is not set
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SF_DEFAULT_BUS=1
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_VITESSE=y
-CONFIG_DM_MDIO=y
-CONFIG_PHY_GIGE=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_SYS_FMAN_FW_ADDR=0x900000
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_SYS_QE_FW_ADDR=0x940000
-CONFIG_SYS_QE_FMAN_FW_IN_MMC=y
-CONFIG_SPECIFY_CONSOLE_INDEX=y
-CONFIG_DM_SERIAL=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
-# CONFIG_SPL_USE_TINY_PRINTF is not set
-CONFIG_RSA=y
-CONFIG_SPL_RSA=y
-CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
diff --git a/configs/ls1043ardb_sdcard_defconfig b/configs/ls1043ardb_sdcard_defconfig
deleted file mode 100644
index aa5404cbb50e..000000000000
--- a/configs/ls1043ardb_sdcard_defconfig
+++ /dev/null
@@ -1,126 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_TARGET_LS1043ARDB=y
-CONFIG_TEXT_BASE=0x82000000
-CONFIG_SYS_MALLOC_LEN=0x102000
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x300000
-CONFIG_SYS_I2C_MXC_I2C1=y
-CONFIG_SYS_I2C_MXC_I2C2=y
-CONFIG_SYS_I2C_MXC_I2C3=y
-CONFIG_SYS_I2C_MXC_I2C4=y
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb"
-CONFIG_SPL_TEXT_BASE=0x10000000
-CONFIG_FSL_LS_PPA=y
-CONFIG_SYS_MONITOR_LEN=1048576
-CONFIG_SPL_MMC=y
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_STACK=0x1001e000
-CONFIG_SPL=y
-CONFIG_PCI=y
-CONFIG_OF_BOARD_FIXUP=y
-CONFIG_LAYERSCAPE_NS_ACCESS=y
-CONFIG_PCIE1=y
-CONFIG_PCIE2=y
-CONFIG_PCIE3=y
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_RAMBOOT_PBL=y
-CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043ardb/ls1043ardb_pbi.cfg"
-CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043ardb/ls1043ardb_rcw_sd.cfg"
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_SD_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-CONFIG_BOOTCOMMAND="run distro_bootcmd; run sd_bootcmd; env exists secureboot && esbc_halt;"
-CONFIG_ARCH_MISC_INIT=y
-CONFIG_MISC_INIT_R=y
-CONFIG_SPL_MAX_SIZE=0x17000
-CONFIG_SPL_PAD_TO=0x1d000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x8f000000
-CONFIG_SPL_BSS_MAX_SIZE=0x80000
-CONFIG_SPL_FSL_PBL=y
-CONFIG_SPL_BOARD_INIT=y
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xf0
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_MPC8XXX_INIT_DDR=y
-CONFIG_SPL_WATCHDOG=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_SPL=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_DM=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_CACHE=y
-CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m at 0x100000(nor_bank0_uboot),40m at 0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m at 0x4100000(nor_bank4_uboot),40m at 0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
-# CONFIG_SPL_EFI_PARTITION is not set
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_USE_ETHPRIME=y
-CONFIG_ETHPRIME="FM1 at DTSEC3"
-CONFIG_FSL_CAAM=y
-CONFIG_MPC8XXX_GPIO=y
-CONFIG_DM_I2C=y
-CONFIG_SPL_SYS_I2C_LEGACY=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x53
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SF_DEFAULT_BUS=1
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_VITESSE=y
-CONFIG_DM_MDIO=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_SYS_FMAN_FW_ADDR=0x900000
-CONFIG_NVME_PCI=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_SYS_QE_FW_ADDR=0x940000
-CONFIG_SYS_QE_FMAN_FW_IN_MMC=y
-CONFIG_DM_SERIAL=y
-CONFIG_SPL_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
-# CONFIG_SPL_USE_TINY_PRINTF is not set
-CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
diff --git a/configs/ls2080aqds_SECURE_BOOT_defconfig b/configs/ls2080aqds_SECURE_BOOT_defconfig
deleted file mode 100644
index d8416265cfb3..000000000000
--- a/configs/ls2080aqds_SECURE_BOOT_defconfig
+++ /dev/null
@@ -1,108 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_GIC_V3_ITS=y
-CONFIG_TARGET_LS2080AQDS=y
-CONFIG_TEXT_BASE=0x30100000
-CONFIG_SYS_MALLOC_LEN=0x202000
-CONFIG_NR_DRAM_BANKS=3
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-qds"
-CONFIG_FSL_LS_PPA=y
-CONFIG_SYS_MONITOR_LEN=1048576
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_NXP_ESBC=y
-CONFIG_FSL_USE_PCA9547_MUX=y
-CONFIG_FSL_QIXIS=y
-# CONFIG_QIXIS_I2C_ACCESS is not set
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_DYNAMIC_SYS_CLK_FREQ=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256"
-CONFIG_BOOTCOMMAND="fsl_mc apply dpl 0x580d00000 && cp.b $kernel_start $kernel_load $kernel_size && bootm $kernel_load"
-CONFIG_RESET_PHY_R=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
-# CONFIG_ISO_PARTITION is not set
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_USE_ETHPRIME=y
-CONFIG_ETHPRIME="DPMAC1 at xgmii"
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_DYNAMIC_DDR_CLK_FREQ=y
-CONFIG_DIMM_SLOTS_PER_CTLR=2
-CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS=2
-CONFIG_DDR_ECC=y
-CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
-CONFIG_SYS_FSL_DDR_INTLV_256B=y
-CONFIG_SYS_I2C_LEGACY=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x57
-CONFIG_FSL_ESDHC=y
-CONFIG_ESDHC_DETECT_QUIRK=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_SYS_MAX_FLASH_BANKS=2
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SYS_NAND_MAX_OOBFREE=2
-CONFIG_SYS_NAND_MAX_ECCPOS=256
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_TERANETICS=y
-CONFIG_PHY_VITESSE=y
-CONFIG_FSL_MEMAC=y
-CONFIG_SYS_MEMAC_LITTLE_ENDIAN=y
-CONFIG_PHY_GIGE=y
-CONFIG_E1000=y
-CONFIG_MII=y
-CONFIG_NVME_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_RTC_ENABLE_32KHZ_OUTPUT=y
-CONFIG_RTC_DS3231=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_FSL_DSPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
-CONFIG_RSA=y
-CONFIG_RSA_SOFTWARE_EXP=y
diff --git a/configs/ls2080aqds_defconfig b/configs/ls2080aqds_defconfig
deleted file mode 100644
index be08d5ba86a8..000000000000
--- a/configs/ls2080aqds_defconfig
+++ /dev/null
@@ -1,109 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_GIC_V3_ITS=y
-CONFIG_TARGET_LS2080AQDS=y
-CONFIG_TEXT_BASE=0x30100000
-CONFIG_SYS_MALLOC_LEN=0x202000
-CONFIG_NR_DRAM_BANKS=3
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-qds"
-CONFIG_FSL_LS_PPA=y
-CONFIG_SYS_MONITOR_LEN=1048576
-CONFIG_ENV_ADDR=0x80300000
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_FSL_USE_PCA9547_MUX=y
-CONFIG_FSL_QIXIS=y
-# CONFIG_QIXIS_I2C_ACCESS is not set
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_DYNAMIC_SYS_CLK_FREQ=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256"
-CONFIG_BOOTCOMMAND="fsl_mc apply dpl 0x580d00000 && cp.b $kernel_start $kernel_load $kernel_size && bootm $kernel_load"
-CONFIG_RESET_PHY_R=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
-# CONFIG_ISO_PARTITION is not set
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_USE_ETHPRIME=y
-CONFIG_ETHPRIME="DPMAC1 at xgmii"
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_FSL_CAAM=y
-CONFIG_DYNAMIC_DDR_CLK_FREQ=y
-CONFIG_DIMM_SLOTS_PER_CTLR=2
-CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS=2
-CONFIG_DDR_ECC=y
-CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
-CONFIG_SYS_FSL_DDR_INTLV_256B=y
-CONFIG_SYS_I2C_LEGACY=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x57
-CONFIG_FSL_ESDHC=y
-CONFIG_ESDHC_DETECT_QUIRK=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_SYS_MAX_FLASH_BANKS=2
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SYS_NAND_MAX_OOBFREE=2
-CONFIG_SYS_NAND_MAX_ECCPOS=256
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SPI_FLASH_EON=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_SST=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_TERANETICS=y
-CONFIG_PHY_VITESSE=y
-CONFIG_FSL_MEMAC=y
-CONFIG_SYS_MEMAC_LITTLE_ENDIAN=y
-CONFIG_PHY_GIGE=y
-CONFIG_E1000=y
-CONFIG_MII=y
-CONFIG_NVME_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_RTC_ENABLE_32KHZ_OUTPUT=y
-CONFIG_RTC_DS3231=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_FSL_DSPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
diff --git a/configs/ls2080aqds_sdcard_defconfig b/configs/ls2080aqds_sdcard_defconfig
deleted file mode 100644
index b45819f87b3e..000000000000
--- a/configs/ls2080aqds_sdcard_defconfig
+++ /dev/null
@@ -1,116 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_GIC_V3_ITS=y
-CONFIG_TARGET_LS2080AQDS=y
-CONFIG_TEXT_BASE=0x80400000
-CONFIG_SYS_MALLOC_LEN=0x0220000
-CONFIG_SYS_MALLOC_F_LEN=0x400
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=3
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_OFFSET=0x300000
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-qds"
-CONFIG_SPL_TEXT_BASE=0x1800a000
-CONFIG_FSL_LS_PPA=y
-CONFIG_SYS_MONITOR_LEN=1048576
-CONFIG_SPL_MMC=y
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_STACK=0x18009ff0
-CONFIG_SPL=y
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_FSL_USE_PCA9547_MUX=y
-CONFIG_FSL_QIXIS=y
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_DYNAMIC_SYS_CLK_FREQ=y
-CONFIG_SD_BOOT=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256"
-CONFIG_BOOTCOMMAND="mmc read 0x80200000 0x6800 0x800; fsl_mc apply dpl 0x80200000 && mmc read $kernel_load $kernel_start $kernel_size && bootm $kernel_load"
-CONFIG_RESET_PHY_R=y
-CONFIG_SPL_MAX_SIZE=0x16000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x80100000
-CONFIG_SPL_BSS_MAX_SIZE=0x100000
-# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x8b0
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_I2C=y
-CONFIG_SPL_MPC8XXX_INIT_DDR=y
-CONFIG_SPL_TARGET="u-boot-with-spl.bin"
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_GREPENV=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
-CONFIG_OF_CONTROL=y
-CONFIG_OF_EMBED=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_USE_ETHPRIME=y
-CONFIG_ETHPRIME="DPMAC1 at xgmii"
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_DYNAMIC_DDR_CLK_FREQ=y
-CONFIG_DIMM_SLOTS_PER_CTLR=2
-CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS=2
-CONFIG_DDR_ECC=y
-CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
-CONFIG_SYS_FSL_DDR_INTLV_256B=y
-CONFIG_SYS_I2C_LEGACY=y
-CONFIG_SYS_I2C_EARLY_INIT=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x57
-CONFIG_FSL_ESDHC=y
-CONFIG_ESDHC_DETECT_QUIRK=y
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SYS_NAND_MAX_OOBFREE=2
-CONFIG_SYS_NAND_MAX_ECCPOS=256
-CONFIG_DM_SPI_FLASH=y
-# CONFIG_SPI_FLASH_BAR is not set
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_TERANETICS=y
-CONFIG_PHY_VITESSE=y
-CONFIG_FSL_MEMAC=y
-CONFIG_SYS_MEMAC_LITTLE_ENDIAN=y
-CONFIG_PHY_GIGE=y
-CONFIG_E1000=y
-CONFIG_MII=y
-CONFIG_NVME_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_RTC_ENABLE_32KHZ_OUTPUT=y
-CONFIG_RTC_DS3231=y
-CONFIG_DM_SCSI=y
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_FSL_QSPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
diff --git a/configs/ls2080ardb_SECURE_BOOT_defconfig b/configs/ls2080ardb_SECURE_BOOT_defconfig
deleted file mode 100644
index 7a22add00038..000000000000
--- a/configs/ls2080ardb_SECURE_BOOT_defconfig
+++ /dev/null
@@ -1,107 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_GIC_V3_ITS=y
-CONFIG_TARGET_LS2080ARDB=y
-CONFIG_TEXT_BASE=0x30100000
-CONFIG_SYS_MALLOC_LEN=0x202000
-CONFIG_NR_DRAM_BANKS=3
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-rdb"
-CONFIG_FSL_LS_PPA=y
-CONFIG_SYS_MONITOR_LEN=1048576
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_NXP_ESBC=y
-CONFIG_FSL_USE_PCA9547_MUX=y
-CONFIG_VID=y
-CONFIG_VID_FLS_ENV="ls2080ardb_vdd_mv"
-CONFIG_VOL_MONITOR_IR36021_READ=y
-CONFIG_VOL_MONITOR_IR36021_SET=y
-CONFIG_FSL_QIXIS=y
-# CONFIG_QIXIS_I2C_ACCESS is not set
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_DYNAMIC_SYS_CLK_FREQ=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS1,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256"
-CONFIG_BOOTCOMMAND="env exists mcinitcmd && env exists secureboot && esbc_validate 0x5806C0000; env exists mcinitcmd && fsl_mc lazyapply dpl 0x580d00000;run distro_bootcmd;run nor_bootcmd; env exists secureboot && esbc_halt;"
-CONFIG_MISC_INIT_R=y
-CONFIG_RESET_PHY_R=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_USE_ETHPRIME=y
-CONFIG_ETHPRIME="DPMAC1 at xgmii"
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_DDR_CLK_FREQ=133333333
-CONFIG_DIMM_SLOTS_PER_CTLR=2
-CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS=2
-CONFIG_DDR_ECC=y
-CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
-CONFIG_SYS_FSL_DDR_INTLV_256B=y
-CONFIG_SYS_I2C_LEGACY=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x57
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_CFI_WIDTH_16BIT=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SYS_NAND_MAX_OOBFREE=2
-CONFIG_SYS_NAND_MAX_ECCPOS=256
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_CORTINA=y
-CONFIG_CORTINA_FW_ADDR=0x580980000
-CONFIG_FSL_MEMAC=y
-CONFIG_SYS_MEMAC_LITTLE_ENDIAN=y
-CONFIG_E1000=y
-CONFIG_MII=y
-CONFIG_NVME_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_RTC_DS3231=y
-CONFIG_DM_SCSI=y
-CONFIG_CONS_INDEX=2
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_FSL_DSPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
-CONFIG_RSA=y
-CONFIG_RSA_SOFTWARE_EXP=y
diff --git a/configs/ls2080ardb_defconfig b/configs/ls2080ardb_defconfig
deleted file mode 100644
index f04b0588206e..000000000000
--- a/configs/ls2080ardb_defconfig
+++ /dev/null
@@ -1,108 +0,0 @@
-CONFIG_ARM=y
-CONFIG_COUNTER_FREQUENCY=25000000
-CONFIG_GIC_V3_ITS=y
-CONFIG_TARGET_LS2080ARDB=y
-CONFIG_TEXT_BASE=0x30100000
-CONFIG_SYS_MALLOC_LEN=0x202000
-CONFIG_NR_DRAM_BANKS=3
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-rdb"
-CONFIG_FSL_LS_PPA=y
-CONFIG_SYS_MONITOR_LEN=1048576
-CONFIG_ENV_ADDR=0x80300000
-CONFIG_PCI=y
-CONFIG_AHCI=y
-CONFIG_FSL_USE_PCA9547_MUX=y
-CONFIG_VID=y
-CONFIG_VID_FLS_ENV="ls2080ardb_vdd_mv"
-CONFIG_VOL_MONITOR_IR36021_READ=y
-CONFIG_VOL_MONITOR_IR36021_SET=y
-CONFIG_FSL_QIXIS=y
-# CONFIG_QIXIS_I2C_ACCESS is not set
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_REMAKE_ELF=y
-CONFIG_MP=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_DYNAMIC_SYS_CLK_FREQ=y
-CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS1,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256"
-CONFIG_BOOTCOMMAND="env exists mcinitcmd && env exists secureboot && esbc_validate 0x5806C0000; env exists mcinitcmd && fsl_mc lazyapply dpl 0x580d00000;run distro_bootcmd;run nor_bootcmd; env exists secureboot && esbc_halt;"
-CONFIG_MISC_INIT_R=y
-CONFIG_RESET_PHY_R=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_PBSIZE=532
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3
-CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_USE_ETHPRIME=y
-CONFIG_ETHPRIME="DPMAC1 at xgmii"
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SATA=y
-CONFIG_SATA_CEVA=y
-CONFIG_FSL_CAAM=y
-CONFIG_DDR_CLK_FREQ=133333333
-CONFIG_DIMM_SLOTS_PER_CTLR=2
-CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS=2
-CONFIG_DDR_ECC=y
-CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
-CONFIG_SYS_FSL_DDR_INTLV_256B=y
-CONFIG_SYS_I2C_LEGACY=y
-CONFIG_SYS_I2C_EEPROM_ADDR=0x57
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_EMPTY_INFO=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_FLASH_CFI_WIDTH_16BIT=y
-CONFIG_SYS_FLASH_QUIET_TEST=y
-CONFIG_SYS_MAX_FLASH_SECT=1024
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_FSL_IFC=y
-CONFIG_SYS_NAND_ONFI_DETECTION=y
-CONFIG_SYS_NAND_MAX_OOBFREE=2
-CONFIG_SYS_NAND_MAX_ECCPOS=256
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_AQUANTIA=y
-CONFIG_PHY_CORTINA=y
-CONFIG_CORTINA_FW_ADDR=0x580980000
-CONFIG_FSL_MEMAC=y
-CONFIG_SYS_MEMAC_LITTLE_ENDIAN=y
-CONFIG_E1000=y
-CONFIG_MII=y
-CONFIG_NVME_PCI=y
-CONFIG_DM_PCI_COMPAT=y
-CONFIG_PCIE_LAYERSCAPE_RC=y
-CONFIG_RTC_DS3231=y
-CONFIG_DM_SCSI=y
-CONFIG_CONS_INDEX=2
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_FSL_DSPI=y
-CONFIG_USB=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_DWC3=y
--
2.17.1
More information about the U-Boot
mailing list