[PATCH v4 01/20] x86: coreboot: Add IDE and SATA
Simon Glass
sjg at chromium.org
Wed Aug 23 23:10:18 CEST 2023
Add these options to permit access to more disk types.
Add some documentation as well.
Signed-off-by: Simon Glass <sjg at chromium.org>
---
(no changes since v1)
configs/coreboot64_defconfig | 1 +
configs/coreboot_defconfig | 9 +++++++++
doc/board/coreboot/coreboot.rst | 20 ++++++++++++++++++++
3 files changed, 30 insertions(+)
diff --git a/configs/coreboot64_defconfig b/configs/coreboot64_defconfig
index 2793e2c0b9d..a456547a25d 100644
--- a/configs/coreboot64_defconfig
+++ b/configs/coreboot64_defconfig
@@ -25,6 +25,7 @@ CONFIG_SYS_PBSIZE=532
CONFIG_CMD_IDE=y
CONFIG_CMD_MMC=y
CONFIG_CMD_PART=y
+CONFIG_CMD_SATA=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
diff --git a/configs/coreboot_defconfig b/configs/coreboot_defconfig
index f196ed776d0..aedad4c93c3 100644
--- a/configs/coreboot_defconfig
+++ b/configs/coreboot_defconfig
@@ -21,8 +21,10 @@ CONFIG_LOGF_LINE=y
CONFIG_LOGF_FUNC=y
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_PCI_INIT_R=y
+CONFIG_CMD_IDE=y
CONFIG_CMD_MMC=y
CONFIG_CMD_PART=y
+CONFIG_CMD_SATA=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@@ -47,6 +49,13 @@ CONFIG_USE_ROOTPATH=y
CONFIG_REGMAP=y
CONFIG_SYSCON=y
# CONFIG_ACPIGEN is not set
+CONFIG_SYS_IDE_MAXDEVICE=4
+CONFIG_SYS_ATA_DATA_OFFSET=0
+CONFIG_SYS_ATA_REG_OFFSET=0
+CONFIG_SYS_ATA_ALT_OFFSET=0
+CONFIG_ATAPI=y
+CONFIG_LBA48=y
+CONFIG_SYS_64BIT_LBA=y
CONFIG_NVME_PCI=y
# CONFIG_PCI_PNP is not set
CONFIG_SOUND=y
diff --git a/doc/board/coreboot/coreboot.rst b/doc/board/coreboot/coreboot.rst
index d660a223d9c..be5b0de5495 100644
--- a/doc/board/coreboot/coreboot.rst
+++ b/doc/board/coreboot/coreboot.rst
@@ -41,6 +41,26 @@ At present it seems that for Minnowboard Max, coreboot does not pass through
the video information correctly (it always says the resolution is 0x0). This
works correctly for link though.
+You can run via QEMU using::
+
+ qemu-system-x86_64 -bios build/coreboot.rom -serial mon:stdio
+
+The `-serial mon:stdio` part shows both output in the display and on the
+console. It is optional. You can add `nographic` as well to *only* get console
+output.
+
+To run with a SATA drive called `$DISK`::
+
+ qemu-system-x86_64 -bios build/coreboot.rom -serial mon:stdio \
+ -drive id=disk,file=$DISK,if=none \
+ -device ahci,id=ahci \
+ -device ide-hd,drive=disk,bus=ahci.0
+
+Then you can scan it with `scsi scan` and access it normally.
+
+To use 4GB of memory, typically necessary for booting Linux distros, add
+`-m 4GB`.
+
64-bit U-Boot
-------------
--
2.42.0.rc1.204.g551eb34607-goog
More information about the U-Boot
mailing list