[PATCH v2 0/3] sunxi: add OrangePi Zero 3 board support
Andre Przywara
andre.przywara at arm.com
Tue Dec 5 19:30:47 CET 2023
On Sun, 3 Dec 2023 21:57:51 -0800
Stephen Graf <stephen.graf at gmail.com> wrote:
Hi Stephen,
> I have tested a newly built u-boot with the patches you provided and it works well.
> It is the same configuration as what I have been testing with for the last few weeks.
>
> I loaded the U-boot to SPI flash and tested with the SD card removed from the system
> and put in a USB card reader. The output for that test is below.
thanks for your testing efforts! Is it OK if I convert this statement into
a "Tested-by:" tag with your email, to become part of the commit?
Cheers,
Andre
> For completeness you might want to mention that another difference between the zero2
> and zero3 is the emac phy going from Realtek to Motorcomm.
>
> Thank you for fixing my patch attempt. It is the first one I have ever done.
> Thank you also for your patience with my fumbling attempts. I have learned a lot
> from you in the last two weeks.
>
> U-Boot SPL 2024.01-rc3-00043-g5c4e9d0c74-dirty (Dec 03 2023 - 18:21:41 -0800)
> DRAM: 1024 MiB
> Trying to boot from sunxi SPI
> NOTICE: BL31: v2.10.0 (debug):v2.10.0
> NOTICE: BL31: Built : 18:07:18, Nov 23 2023
> NOTICE: BL31: Detected Allwinner H616 SoC (1823)
> NOTICE: BL31: Found U-Boot DTB at 0x4a0b2828, model: OrangePi Zero3
> INFO: ARM GICv2 driver initialized
> INFO: Configuring SPC Controller
> INFO: PMIC: Probing AXP305 on RSB
> ERROR: RSB: set run-time address: 0x10003
> INFO: Could not init RSB: -65539
> INFO: BL31: Platform setup done
> INFO: BL31: Initializing runtime services
> INFO: BL31: cortex_a53: CPU workaround for erratum 855873 was applied
> INFO: BL31: cortex_a53: CPU workaround for erratum 1530924 was applied
> INFO: PSCI: Suspend is unavailable
> INFO: BL31: Preparing for EL3 exit to normal world
> INFO: Entry point address = 0x4a000000
> INFO: SPSR = 0x3c9
> INFO: Changed devicetree.
>
>
> U-Boot 2024.01-rc3-00043-g5c4e9d0c74-dirty (Dec 03 2023 - 18:21:41 -0800) Allwinner Technology
>
> CPU: Allwinner H616 (SUN50I)
> Model: OrangePi Zero3
> DRAM: 1 GiB
> Core: 57 devices, 25 uclasses, devicetree: separate
> WDT: Not starting watchdog at 30090a0
> MMC: mmc at 4020000: 0
> Loading Environment from SPIFlash... SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
> OK
> In: serial at 5000000
> Out: serial at 5000000
> Err: serial at 5000000
> Allwinner mUSB OTG (Peripheral)
> Net: eth0: ethernet at 5020000using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in
> MAC de:ad:be:ef:00:01
> HOST MAC de:ad:be:ef:00:00
> RNDIS ready
> , eth1: usb_ether
> starting USB...
> Bus usb at 5200000: USB EHCI 1.00
> Bus usb at 5200400: USB OHCI 1.0
> scanning bus usb at 5200000 for devices... Device NOT ready
> Request Sense returned 02 3A 00
> Device NOT ready
> Request Sense returned 02 3A 00
> Device NOT ready
> Request Sense returned 02 3A 00
> 2 USB Device(s) found
> scanning bus usb at 5200400 for devices... 1 USB Device(s) found
> scanning usb for storage devices... 1 Storage Device(s) found
> Hit any key to stop autoboot: 0
> Card did not respond to voltage select! : -110
>
> Device 0: Vendor: Generic- Rev: 1.00 Prod: SD/MMC
> Type: Removable Hard Disk
> Capacity: 15193.5 MB = 14.8 GB (31116288 x 512)
> ... is now current device
> Scanning usb 0:1...
> Found U-Boot script /boot/boot.scr
> 1052 bytes read in 1 ms (1 MiB/s)
> ## Executing script at 4fc00000
> Card did not respond to voltage select! : -110
> ** Bad device specification mmc 0 **
> 19472 bytes read in 3 ms (6.2 MiB/s)
> No FDT memory address configured. Please configure
> the FDT address via "fdt addr <address>" command.
> Aborting!
> 7088139 bytes read in 324 ms (20.9 MiB/s)
> 22491144 bytes read in 1025 ms (20.9 MiB/s)
> Moving Image from 0x40080000 to 0x40200000, end=41800000
> ## Loading init Ramdisk from Legacy Image at 4ff00000 ...
> Image Name: uInitrd
> Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
> Data Size: 7088075 Bytes = 6.8 MiB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
> ## Flattened Device Tree blob at 4fa00000
> Booting using the fdt blob at 0x4fa00000
> Working FDT set to 4fa00000
> Loading Ramdisk to 4993d000, end 49fff7cb ... OK
> Loading Device Tree to 0000000049935000, end 000000004993cc0f ... OK
> Working FDT set to 49935000
>
> Starting kernel ...
>
>
> Welcome to Debian GNU/Linux 12 (bookworm)!
>
>
>
> On 2023-12-03 4:59 p.m., Andre Przywara wrote:
> > A small update for the OrangePi Zero 3 support series. This fixes
> > USB support, and upgrades the DRAM clock to 792, for better stability
> > (as the other DRAM parameters were tailored to that frequency). I added
> > the tags on the way.
> > Please test!
> >
> > =================
> > The OrangePi Zero 3 is a small development board featuring the Allwinner
> > H618 SoC. Compared to its predecessor OrangePi Zero 2, the new board uses
> > LPDDR4 DRAM instead of DDR3 DRAM, and an X-Powers AXP313 PMIC instead of
> > the AXP305.
> > U-Boot gained support for both LPDDR4 DRAM and the new PMIC just
> > recently, so add a user for those features by adding a defconfig for the
> > new board.
> > To make this work, patch 1/3 introduces support for zBIT SPI NOR flash
> > chip, and patch 2/3 removes the default AXP305 PMIC selection when
> > compiling for H616 SoCs.
> > Patch 3/3 then adds the defconfig. The DT was already synced from the
> > Linux kernel repo a few weeks ago.
> >
> > Cheers,
> > Andre
> >
> > Changelog v1 .. v2:
> > - add tags
> > - set DRAM clock to 792 MHz (from the default 720 MHz)
> > - fix USB support by supplying USB VBUS enable GPIO
> >
> > Andre Przywara (3):
> > mtd: spi-nor: Add support for zBIT ZB25VQ128
> > sunxi: H616: remove default AXP305 selection
> > sunxi: H616: Add OrangePi Zero 3 board support
> >
> > arch/arm/dts/Makefile | 1 +
> > board/sunxi/MAINTAINERS | 5 +++++
> > configs/orangepi_zero2_defconfig | 1 +
> > configs/orangepi_zero3_defconfig | 32 ++++++++++++++++++++++++++++++++
> > configs/x96_mate_defconfig | 1 +
> > drivers/mtd/spi/Kconfig | 5 +++++
> > drivers/mtd/spi/spi-nor-ids.c | 5 +++++
> > drivers/power/Kconfig | 1 -
> > 8 files changed, 50 insertions(+), 1 deletion(-)
> > create mode 100644 configs/orangepi_zero3_defconfig
> >
More information about the U-Boot
mailing list