[PATCH v2 20/32] dts: sdm845: import supporting dtsi files
Caleb Connolly
caleb.connolly at linaro.org
Tue Dec 19 17:04:21 CET 2023
Import the PM8998 and PMI8998 PMIC DTSI files from Linux 6.7-rc3 as well
as the common audio codec in preperation for replacing board DTS files
with upstream.
Signed-off-by: Caleb Connolly <caleb.connolly at linaro.org>
---
arch/arm/dts/pm8998.dtsi | 130 +++++++++++++++++++++++++++++++++++++++
arch/arm/dts/pmi8998.dtsi | 98 +++++++++++++++++++++++++++++
arch/arm/dts/sdm845-wcd9340.dtsi | 86 ++++++++++++++++++++++++++
3 files changed, 314 insertions(+)
diff --git a/arch/arm/dts/pm8998.dtsi b/arch/arm/dts/pm8998.dtsi
new file mode 100644
index 000000000000..3f82715392c6
--- /dev/null
+++ b/arch/arm/dts/pm8998.dtsi
@@ -0,0 +1,130 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/* Copyright 2018 Google LLC. */
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ thermal-zones {
+ pm8998-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&pm8998_temp>;
+
+ trips {
+ pm8998_alert0: pm8998-alert0 {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ pm8998_crit: pm8998-crit {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
+
+&spmi_bus {
+ pm8998_lsid0: pmic at 0 {
+ compatible = "qcom,pm8998", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8998_pon: pon at 800 {
+ compatible = "qcom,pm8998-pon";
+
+ reg = <0x800>;
+ mode-bootloader = <0x2>;
+ mode-recovery = <0x1>;
+
+ pm8998_pwrkey: pwrkey {
+ compatible = "qcom,pm8941-pwrkey";
+ interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_POWER>;
+ };
+
+ pm8998_resin: resin {
+ compatible = "qcom,pm8941-resin";
+ interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ status = "disabled";
+ };
+ };
+
+ pm8998_temp: temp-alarm at 2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
+ io-channels = <&pm8998_adc ADC5_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8998_coincell: charger at 2800 {
+ compatible = "qcom,pm8998-coincell", "qcom,pm8941-coincell";
+ reg = <0x2800>;
+
+ status = "disabled";
+ };
+
+ pm8998_adc: adc at 3100 {
+ compatible = "qcom,spmi-adc-rev2";
+ reg = <0x3100>;
+ interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+
+ channel at 6 {
+ reg = <ADC5_DIE_TEMP>;
+ label = "die_temp";
+ };
+ };
+
+ pm8998_adc_tm: adc-tm at 3400 {
+ compatible = "qcom,spmi-adc-tm-hc";
+ reg = <0x3400>;
+ interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
+ #thermal-sensor-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ rtc at 6000 {
+ compatible = "qcom,pm8941-rtc";
+ reg = <0x6000>, <0x6100>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+ };
+
+ pm8998_gpios: gpio at c000 {
+ compatible = "qcom,pm8998-gpio", "qcom,spmi-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ gpio-ranges = <&pm8998_gpios 0 0 26>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ };
+
+ pm8998_lsid1: pmic at 1 {
+ compatible = "qcom,pm8998", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
diff --git a/arch/arm/dts/pmi8998.dtsi b/arch/arm/dts/pmi8998.dtsi
new file mode 100644
index 000000000000..cd3f0790fd42
--- /dev/null
+++ b/arch/arm/dts/pmi8998.dtsi
@@ -0,0 +1,98 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+ pmi8998_lsid0: pmic at 2 {
+ compatible = "qcom,pmi8998", "qcom,spmi-pmic";
+ reg = <0x2 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmi8998_charger: charger at 1000 {
+ compatible = "qcom,pmi8998-charger";
+ reg = <0x1000>;
+
+ interrupts = <0x2 0x13 0x4 IRQ_TYPE_EDGE_BOTH>,
+ <0x2 0x12 0x2 IRQ_TYPE_EDGE_BOTH>,
+ <0x2 0x16 0x1 IRQ_TYPE_EDGE_RISING>,
+ <0x2 0x13 0x6 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "usb-plugin",
+ "bat-ov",
+ "wdog-bark",
+ "usbin-icl-change";
+
+ io-channels = <&pmi8998_rradc 3>,
+ <&pmi8998_rradc 4>;
+ io-channel-names = "usbin_i", "usbin_v";
+
+ status = "disabled";
+ };
+
+ pmi8998_gpios: gpio at c000 {
+ compatible = "qcom,pmi8998-gpio", "qcom,spmi-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ gpio-ranges = <&pmi8998_gpios 0 0 14>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pmi8998_rradc: adc at 4500 {
+ compatible = "qcom,pmi8998-rradc";
+ reg = <0x4500>;
+ #io-channel-cells = <1>;
+ };
+ };
+
+ pmi8998_lsid1: pmic at 3 {
+ compatible = "qcom,pmi8998", "qcom,spmi-pmic";
+ reg = <0x3 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ labibb {
+ compatible = "qcom,pmi8998-lab-ibb";
+
+ ibb: ibb {
+ interrupts = <0x3 0xdc 0x2 IRQ_TYPE_EDGE_RISING>,
+ <0x3 0xdc 0x0 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "sc-err", "ocp";
+ };
+
+ lab: lab {
+ interrupts = <0x3 0xde 0x1 IRQ_TYPE_EDGE_RISING>,
+ <0x3 0xde 0x0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "sc-err", "ocp";
+ };
+ };
+
+ pmi8998_lpg: pwm {
+ compatible = "qcom,pmi8998-lpg";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #pwm-cells = <2>;
+
+ status = "disabled";
+ };
+
+ pmi8998_flash: led-controller at d300 {
+ compatible = "qcom,pmi8998-flash-led", "qcom,spmi-flash-led";
+ reg = <0xd300>;
+ status = "disabled";
+ };
+
+ pmi8998_wled: leds at d800 {
+ compatible = "qcom,pmi8998-wled";
+ reg = <0xd800>, <0xd900>;
+ interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>,
+ <0x3 0xd8 0x2 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "ovp", "short";
+ label = "backlight";
+
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/arm/dts/sdm845-wcd9340.dtsi b/arch/arm/dts/sdm845-wcd9340.dtsi
new file mode 100644
index 000000000000..c15d48860646
--- /dev/null
+++ b/arch/arm/dts/sdm845-wcd9340.dtsi
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM845 SoC device tree source
+ *
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+&slim {
+ status = "okay";
+
+ slim at 1 {
+ reg = <1>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ wcd9340_ifd: ifd at 0,0 {
+ compatible = "slim217,250";
+ reg = <0 0>;
+ };
+
+ wcd9340: codec at 1,0 {
+ compatible = "slim217,250";
+ reg = <1 0>;
+ slim-ifc-dev = <&wcd9340_ifd>;
+
+ #sound-dai-cells = <1>;
+
+ interrupts-extended = <&tlmm 54 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ clock-names = "extclk";
+ clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
+
+ #clock-cells = <0>;
+ clock-frequency = <9600000>;
+ clock-output-names = "mclk";
+
+ pinctrl-0 = <&wcd_intr_default>;
+ pinctrl-names = "default";
+
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ wcdgpio: gpio-controller at 42 {
+ compatible = "qcom,wcd9340-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x42 0x2>;
+ };
+
+ swm: swm at c85 {
+ compatible = "qcom,soundwire-v1.3.0";
+ reg = <0xc85 0x40>;
+ interrupts-extended = <&wcd9340 20>;
+
+ qcom,dout-ports = <6>;
+ qcom,din-ports = <2>;
+ qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1f 0x3f 0x7 0x1f 0x3f 0x0f 0x0f>;
+ qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0c 0x6 0x12 0x0d 0x07 0x0a>;
+ qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x1f 0x00 0x00 0x1f 0x00 0x00>;
+
+ #sound-dai-cells = <1>;
+ clocks = <&wcd9340>;
+ clock-names = "iface";
+ #address-cells = <2>;
+ #size-cells = <0>;
+ };
+ };
+ };
+};
+
+&tlmm {
+ wcd_intr_default: wcd-intr-default-state {
+ pins = "gpio54";
+ function = "gpio";
+
+ bias-pull-down;
+ drive-strength = <2>;
+ };
+};
--
2.42.1
More information about the U-Boot
mailing list