[PATCH RFC u-boot-mvebu 00/59] arm: mvebu: Various fixes

[Pali Rohár]

On Wednesday 22 February 2023 15:16:06 Tony Dinh wrote:
> Hi Pali,
> 
> On Wed, Feb 22, 2023 at 3:06 PM Pali Rohár <pali at kernel.org> wrote:
> >
> > On Wednesday 22 February 2023 14:16:36 Tony Dinh wrote:
> > > Hi Pali,
> > >
> > > On Tue, Feb 21, 2023 at 11:58 PM Pali Rohár <pali at kernel.org> wrote:
> > > >
> > > > On Tuesday 21 February 2023 21:45:07 Tony Dinh wrote:
> > > > > Hi Pali,
> > > > >
> > > > > On Tue, Feb 21, 2023 at 3:14 PM Pali Rohár <pali at kernel.org> wrote:
> > > > > >
> > > > > > On Tuesday 21 February 2023 15:06:16 Tony Dinh wrote:
> > > > > > > Hi Pali,
> > > > > > >
> > > > > > > On Tue, Feb 21, 2023 at 12:22 PM Pali Rohár <pali at kernel.org> wrote:
> > > > > > > >
> > > > > > > > This patch series contains various improvements and fixes for existing
> > > > > > > > logical errors. Boot phase was adjusted to match behavior of Armada 385
> > > > > > > > BootROM by inspecting and disassembling of BootROM binary dump itself.
> > > > > > > > Important information are included in documentation patch for kwboot.
> > > > > > > > Most of the changes are untested, hence this patch series is just RFC.
> > > > > > > > So please test changes before applying, idealy on SPI, SATA and SD/MMC.
> > > > > > > > Nevertheless all patches on github passed CI testing in this PR:
> > > > > > > > https://github.com/u-boot/u-boot/pull/275
> > > > > > ...
> > > > > > > I went to patchwork and downloaded the series.
> > > > > > > https://patchwork.ozlabs.org/project/uboot/patch/20230221201925.9644-2-pali@kernel.org
> > > > > > >
> > > > > > > When I applied the patches set there were some rejections.
> > > > > > > <BEGIN LOG>
> > > > > > > # patch -p1 < /usr/src/builds-u-boot-marvell/pali_patches/arm-mvebu-Various-fixes.patch
> > > > > > >
> > > > > > ...
> > > > > > FAILED
> > > > > > ...
> > > > > > > <END LOG>
> > > > > > >
> > > > > > > I'm on the latest master branch (just did a git pull today). Could
> > > > > > > some patches be out of order?
> > > > > > >
> > > > > > > Thanks,
> > > > > > > Tony
> > > > > >
> > > > > > Well, that is because DENX mail server is broken and it crashed during
> > > > > > processing antispam filter on my some of my patches. So some patches are
> > > > > > missing in archive and then applying dependent patches failed.
> > > > > >
> > > > > > So ignore patchwork and email patches. Rather fetch changes from the
> > > > > > mentioned github pull request https://github.com/u-boot/u-boot/pull/275
> > > > > >
> > > > > > You can do it via git command (it fetch it to the new mvebu branch):
> > > > > >
> > > > > >   git fetch https://github.com/u-boot/u-boot.git refs/pull/275/merge:mvebu
> > > > >
> > > > > Indeed! That pull request was applied without problem.
> > > > >
> > > > > So I did a general regression test running rebuilt kwboot binary, and
> > > > > rebuilt u-boot images for these 2 Marvell boards:
> > > > >
> > > > > Thecus N2350 (Armada 385)
> > > > > Pogo V4 (Kirkwood 88F6192).
> > > > >
> > > > > So for that part:
> > > > > Tested-by: Tony Dinh <mibodhi at gmail.com>
> > > > >
> > > > > All the best,
> > > > > Tony
> > > >
> > > > Thanks for testing! Anyway do you have some A38x board which can boot
> > > > from SD/MMC, SATA or NAND? This is what is needed to test too. I see
> > > > that Pogo boots from NAND but it does not use SPL.
> > >
> > > I have only one A38x board with NAND: the Thecus N2350. I am creating
> > > a new defconfig and will see if I can boot it from the NAND flash.
> >
> > Ok. And do you have some switch on this board which instruct BootROM to
> > really boot from NAND?
> 
> No switch that I can see. So I'm going to erase the u-boot image in
> SPI to let the BootROM try booting from NAND.

BootROM on 32-bit mvebu SoCs always boots from the location configured
by strapping pins. So if you do not have any switch (or possible
soldered zero-ohm resistors) on the board then I doubt that BootROM will
try to boot from NAND.

> >
> > > By the way, I'm having this build error that CFG_SYS_NAND_BASE is not
> > > defined. What should it be for A38x? is it the same for Kirkwood?
> > >
> > > All the best,
> > > Tony
> >
> > Is SYS_NAND_BASE really needed? If yet then I think it should be macro
> > MVEBU_NAND_BASE.
> 
> The build error looks like this:
> drivers/mtd/nand/raw/nand.c:15:34: error: ‘CFG_SYS_NAND_BASE’
> undeclared here (not in a function); did you mean
> ‘CFG_SYS_PL310_BASE’?
>    15 | #define CFG_SYS_NAND_BASE_LIST { CFG_SYS_NAND_BASE }
> 

I see... Maybe you can try to enable SYS_NAND_SELF_INIT.

> >
> > But on Kirkwood is SYS_NAND_BASE set to the DEFADR_NANDF value which is
> > memory mapping of NAND device via mbus. On Armada devices is not NAND
> > device mbus mapped at all and MVEBU_NAND_BASE points to internal mvebu
> > registers. So I'm quite not sure if it would work.
> >
> > So lets try with MVEBU_NAND_BASE.
> 
> OK.
> 
> Thanks,
> Tony