[PATCH v2 1/2] configs: j721s2: merge HS and non-HS defconfigs

Manorit Chawdhry m-chawdhry at ti.com
Fri Feb 24 06:07:48 CET 2023 

K3 devices have runtime type board detection. Make the default defconfig
include the secure configuration. Then remove the HS specific config.

Non-HS devices will continue to boot due to runtime device type detection.
If TI_SECURE_DEV_PKG is not set the build will emit warnings, for non-HS
devices these can be ignored.

Signed-off-by: Manorit Chawdhry <m-chawdhry at ti.com>
Acked-by: Andrew Davis <afd at ti.com>
---
v1->v2:
update MAINTAINERS

 MAINTAINERS                         |   2 -
 configs/j721s2_evm_a72_defconfig    |   3 +-
 configs/j721s2_evm_r5_defconfig     |   1 +
 configs/j721s2_hs_evm_a72_defconfig | 213 ----------------------------
 configs/j721s2_hs_evm_r5_defconfig  | 176 -----------------------
 5 files changed, 3 insertions(+), 392 deletions(-)
 delete mode 100644 configs/j721s2_hs_evm_a72_defconfig
 delete mode 100644 configs/j721s2_hs_evm_r5_defconfig

diff --git a/MAINTAINERS b/MAINTAINERS
index b9c505d5faa7..bdea0704adc0 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1457,8 +1457,6 @@ F:	configs/j7200_hs_evm_a72_defconfig
 F:	configs/j7200_hs_evm_r5_defconfig
 F:	configs/j721e_hs_evm_a72_defconfig
 F:	configs/j721e_hs_evm_r5_defconfig
-F:	configs/j721s2_hs_evm_a72_defconfig
-F:	configs/j721s2_hs_evm_r5_defconfig
 
 TPM DRIVERS
 M:	Ilias Apalodimas <ilias.apalodimas at linaro.org>
diff --git a/configs/j721s2_evm_a72_defconfig b/configs/j721s2_evm_a72_defconfig
index 84b4fb083191..c880a8d37158 100644
--- a/configs/j721s2_evm_a72_defconfig
+++ b/configs/j721s2_evm_a72_defconfig
@@ -1,5 +1,6 @@
 CONFIG_ARM=y
 CONFIG_ARCH_K3=y
+CONFIG_TI_SECURE_DEVICE=y
 CONFIG_SYS_MALLOC_LEN=0x2000000
 CONFIG_SYS_MALLOC_F_LEN=0x8000
 CONFIG_SPL_GPIO=y
@@ -32,7 +33,7 @@ CONFIG_SPL_LOAD_FIT=y
 CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
 # CONFIG_USE_SPL_FIT_GENERATOR is not set
 CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTCOMMAND="run findfdt; run envboot; run init_${boot}; run boot_rprocs; run get_kern_${boot}; run get_fdt_${boot}; run get_overlay_${boot}; run run_kern"
+CONFIG_BOOTCOMMAND="run findfdt; run envboot; run init_${boot}; run boot_rprocs; if test ${boot_fit} -eq 1; then run get_fit_${boot}; run get_overlaystring; run run_fit; else; run get_kern_${boot}; run get_fdt_${boot}; run get_overlay_${boot}; run run_kern; fi;"
 CONFIG_LOGLEVEL=7
 CONFIG_SPL_MAX_SIZE=0xc0000
 CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
diff --git a/configs/j721s2_evm_r5_defconfig b/configs/j721s2_evm_r5_defconfig
index 1f2102a9f91f..51f2da66c9d1 100644
--- a/configs/j721s2_evm_r5_defconfig
+++ b/configs/j721s2_evm_r5_defconfig
@@ -1,5 +1,6 @@
 CONFIG_ARM=y
 CONFIG_ARCH_K3=y
+CONFIG_TI_SECURE_DEVICE=y
 CONFIG_SYS_MALLOC_LEN=0x2000000
 CONFIG_SYS_MALLOC_F_LEN=0x10000
 CONFIG_SPL_GPIO=y
diff --git a/configs/j721s2_hs_evm_a72_defconfig b/configs/j721s2_hs_evm_a72_defconfig
deleted file mode 100644
index 9fc90737da80..000000000000
--- a/configs/j721s2_hs_evm_a72_defconfig
+++ /dev/null
@@ -1,213 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_K3=y
-CONFIG_TI_SECURE_DEVICE=y
-CONFIG_SYS_MALLOC_LEN=0x2000000
-CONFIG_SYS_MALLOC_F_LEN=0x8000
-CONFIG_SPL_GPIO=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_SOC_K3_J721S2=y
-CONFIG_TARGET_J721S2_A72_EVM=y
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_OFFSET=0x680000
-CONFIG_DM_GPIO=y
-CONFIG_SPL_DM_SPI=y
-CONFIG_DEFAULT_DEVICE_TREE="k3-j721s2-common-proc-board"
-CONFIG_SPL_TEXT_BASE=0x80080000
-CONFIG_SPL_MMC=y
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_STACK_R_ADDR=0x82000000
-CONFIG_ENV_OFFSET_REDUND=0x6A0000
-CONFIG_SPL_FS_FAT=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI=y
-# CONFIG_PSCI_RESET is not set
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80480000
-# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
-CONFIG_SPL_LOAD_FIT=y
-CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
-# CONFIG_USE_SPL_FIT_GENERATOR is not set
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTCOMMAND="run findfdt; run envboot; run init_${boot}; run boot_rprocs; run get_fit_${boot}; run get_overlaystring; run run_fit"
-CONFIG_LOGLEVEL=7
-CONFIG_SPL_MAX_SIZE=0xc0000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x80a00000
-CONFIG_SPL_BSS_MAX_SIZE=0x80000
-CONFIG_SPL_BOARD_INIT=y
-CONFIG_SPL_SYS_MALLOC_SIMPLE=y
-CONFIG_SPL_STACK_R=y
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_SYS_SPL_MALLOC_SIZE=0x800000
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x1400
-CONFIG_SPL_DMA=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot.img"
-CONFIG_SPL_I2C=y
-CONFIG_SPL_DM_MAILBOX=y
-CONFIG_SPL_MTD_SUPPORT=y
-CONFIG_SPL_DM_SPI_FLASH=y
-CONFIG_SPL_NOR_SUPPORT=y
-CONFIG_SPL_DM_RESET=y
-CONFIG_SPL_POWER_DOMAIN=y
-CONFIG_SPL_RAM_SUPPORT=y
-CONFIG_SPL_RAM_DEVICE=y
-# CONFIG_SPL_SPI_FLASH_TINY is not set
-CONFIG_SPL_SPI_FLASH_SFDP_SUPPORT=y
-CONFIG_SPL_SPI_LOAD=y
-CONFIG_SYS_SPI_U_BOOT_OFFS=0x280000
-CONFIG_SPL_THERMAL=y
-CONFIG_SPL_USB_GADGET=y
-CONFIG_SPL_DFU=y
-CONFIG_SPL_YMODEM_SUPPORT=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_DFU=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_MTD=y
-CONFIG_CMD_REMOTEPROC=y
-CONFIG_CMD_UFS=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_USB_MASS_STORAGE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_MTDIDS_DEFAULT="nor0=47040000.spi.0,nor0=47034000.hyperbus"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=47040000.spi.0:512k(ospi.tiboot3),2m(ospi.tispl),4m(ospi.u-boot),256k(ospi.env),256k(ospi.env.backup),57088k at 8m(ospi.rootfs),256k(ospi.phypattern);47034000.hyperbus:512k(hbmc.tiboot3),2m(hbmc.tispl),4m(hbmc.u-boot),256k(hbmc.env),- at 8m(hbmc.rootfs)"
-CONFIG_CMD_UBI=y
-# CONFIG_ISO_PARTITION is not set
-# CONFIG_SPL_EFI_PARTITION is not set
-CONFIG_OF_CONTROL=y
-CONFIG_SPL_OF_CONTROL=y
-CONFIG_SPL_MULTI_DTB_FIT=y
-CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SPL_DM=y
-CONFIG_SPL_DM_SEQ_ALIAS=y
-CONFIG_REGMAP=y
-CONFIG_SPL_REGMAP=y
-CONFIG_SYSCON=y
-CONFIG_SPL_SYSCON=y
-CONFIG_SPL_OF_TRANSLATE=y
-CONFIG_CLK=y
-CONFIG_SPL_CLK=y
-CONFIG_CLK_CCF=y
-CONFIG_CLK_TI_SCI=y
-CONFIG_DFU_MMC=y
-CONFIG_DFU_RAM=y
-CONFIG_DFU_SF=y
-CONFIG_SYS_DFU_DATA_BUF_SIZE=0x40000
-CONFIG_SYS_DFU_MAX_FILE_SIZE=0x800000
-CONFIG_DMA_CHANNELS=y
-CONFIG_TI_K3_NAVSS_UDMA=y
-CONFIG_USB_FUNCTION_FASTBOOT=y
-CONFIG_FASTBOOT_BUF_ADDR=0x82000000
-CONFIG_FASTBOOT_BUF_SIZE=0x2F000000
-CONFIG_FASTBOOT_FLASH=y
-CONFIG_FASTBOOT_FLASH_MMC_DEV=0
-CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
-CONFIG_TI_SCI_PROTOCOL=y
-CONFIG_DA8XX_GPIO=y
-CONFIG_DM_PCA953X=y
-CONFIG_DM_I2C=y
-CONFIG_DM_I2C_GPIO=y
-CONFIG_SYS_I2C_OMAP24XX=y
-CONFIG_DM_MAILBOX=y
-CONFIG_K3_SEC_PROXY=y
-CONFIG_SUPPORT_EMMC_BOOT=y
-CONFIG_MMC_IO_VOLTAGE=y
-CONFIG_MMC_UHS_SUPPORT=y
-CONFIG_MMC_HS400_SUPPORT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
-CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_ADMA=y
-CONFIG_SPL_MMC_SDHCI_ADMA=y
-CONFIG_MMC_SDHCI_AM654=y
-CONFIG_MTD=y
-CONFIG_DM_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_SHOW_PROGRESS=0
-CONFIG_CFI_FLASH=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SPI_FLASH_SFDP_SUPPORT=y
-CONFIG_SPI_FLASH_SOFT_RESET=y
-CONFIG_SPI_FLASH_SOFT_RESET_ON_BOOT=y
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_MT35XU=y
-# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
-CONFIG_SPI_FLASH_MTD=y
-CONFIG_MULTIPLEXER=y
-CONFIG_MUX_MMIO=y
-CONFIG_PHY_TI_DP83867=y
-CONFIG_PHY_FIXED=y
-CONFIG_TI_AM65_CPSW_NUSS=y
-CONFIG_PHY=y
-CONFIG_SPL_PHY=y
-CONFIG_PHY_CADENCE_TORRENT=y
-CONFIG_PHY_J721E_WIZ=y
-CONFIG_PINCTRL=y
-# CONFIG_PINCTRL_GENERIC is not set
-CONFIG_SPL_PINCTRL=y
-# CONFIG_SPL_PINCTRL_GENERIC is not set
-CONFIG_PINCTRL_SINGLE=y
-CONFIG_POWER_DOMAIN=y
-CONFIG_TI_SCI_POWER_DOMAIN=y
-CONFIG_DM_REGULATOR=y
-CONFIG_DM_REGULATOR_FIXED=y
-CONFIG_DM_REGULATOR_GPIO=y
-CONFIG_RAM=y
-CONFIG_SPL_RAM=y
-CONFIG_REMOTEPROC_TI_K3_DSP=y
-CONFIG_REMOTEPROC_TI_K3_R5F=y
-CONFIG_DM_RESET=y
-CONFIG_RESET_TI_SCI=y
-CONFIG_SCSI=y
-CONFIG_DM_SCSI=y
-CONFIG_DM_SERIAL=y
-CONFIG_SOC_DEVICE=y
-CONFIG_SOC_DEVICE_TI_K3=y
-CONFIG_SOC_TI=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_CADENCE_QSPI=y
-CONFIG_HAS_CQSPI_REF_CLK=y
-CONFIG_CQSPI_REF_CLK=133333333
-CONFIG_SYSRESET=y
-CONFIG_SPL_SYSRESET=y
-CONFIG_SYSRESET_TI_SCI=y
-CONFIG_DM_THERMAL=y
-CONFIG_USB=y
-CONFIG_DM_USB_GADGET=y
-CONFIG_SPL_DM_USB_GADGET=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_CDNS3=y
-CONFIG_USB_CDNS3_GADGET=y
-CONFIG_USB_CDNS3_HOST=y
-CONFIG_SPL_USB_CDNS3_GADGET=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0451
-CONFIG_USB_GADGET_PRODUCT_NUM=0x6168
-CONFIG_UFS=y
-CONFIG_CADENCE_UFS=y
-CONFIG_TI_J721E_UFS=y
-CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/configs/j721s2_hs_evm_r5_defconfig b/configs/j721s2_hs_evm_r5_defconfig
deleted file mode 100644
index d9988fc17fc7..000000000000
--- a/configs/j721s2_hs_evm_r5_defconfig
+++ /dev/null
@@ -1,176 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_K3=y
-CONFIG_TI_SECURE_DEVICE=y
-CONFIG_SYS_MALLOC_LEN=0x2000000
-CONFIG_SYS_MALLOC_F_LEN=0x10000
-CONFIG_SPL_GPIO=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_SOC_K3_J721S2=y
-CONFIG_K3_EARLY_CONS=y
-CONFIG_TARGET_J721S2_R5_EVM=y
-CONFIG_ENV_SIZE=0x20000
-CONFIG_DM_GPIO=y
-CONFIG_SPL_DM_SPI=y
-CONFIG_DEFAULT_DEVICE_TREE="k3-j721s2-r5-common-proc-board"
-CONFIG_SPL_TEXT_BASE=0x41c00000
-CONFIG_SPL_MMC=y
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_STACK_R_ADDR=0x82000000
-CONFIG_SPL_SIZE_LIMIT=0x80000
-CONFIG_SPL_SIZE_LIMIT_PROVIDE_STACK=0x4000
-CONFIG_SPL_FS_FAT=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI=y
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x41c76000
-# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
-CONFIG_SPL_LOAD_FIT=y
-CONFIG_SPL_LOAD_FIT_ADDRESS=0x80080000
-# CONFIG_USE_SPL_FIT_GENERATOR is not set
-CONFIG_USE_BOOTCOMMAND=y
-# CONFIG_DISPLAY_CPUINFO is not set
-CONFIG_SPL_SIZE_LIMIT_SUBTRACT_GD=y
-CONFIG_SPL_SIZE_LIMIT_SUBTRACT_MALLOC=y
-CONFIG_SPL_MAX_SIZE=0xc0000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x41c76000
-CONFIG_SPL_BSS_MAX_SIZE=0xa000
-CONFIG_SPL_SYS_REPORT_STACK_F_USAGE=y
-CONFIG_SPL_BOARD_INIT=y
-CONFIG_SPL_SYS_MALLOC_SIMPLE=y
-CONFIG_SPL_STACK_R=y
-CONFIG_SPL_SEPARATE_BSS=y
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y
-CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x84000000
-CONFIG_SYS_SPL_MALLOC_SIZE=0x1000000
-CONFIG_SPL_EARLY_BSS=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x400
-CONFIG_SPL_DMA=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_FS_EXT4=y
-CONFIG_SPL_I2C=y
-CONFIG_SPL_DM_MAILBOX=y
-CONFIG_SPL_MTD_SUPPORT=y
-CONFIG_SPL_DM_SPI_FLASH=y
-CONFIG_SPL_NOR_SUPPORT=y
-CONFIG_SPL_DM_RESET=y
-CONFIG_SPL_POWER_DOMAIN=y
-CONFIG_SPL_RAM_SUPPORT=y
-CONFIG_SPL_RAM_DEVICE=y
-CONFIG_SPL_REMOTEPROC=y
-# CONFIG_SPL_SPI_FLASH_TINY is not set
-CONFIG_SPL_SPI_FLASH_SFDP_SUPPORT=y
-CONFIG_SPL_SPI_LOAD=y
-CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
-CONFIG_SPL_THERMAL=y
-CONFIG_SPL_USB_GADGET=y
-CONFIG_SPL_DFU=y
-CONFIG_SPL_YMODEM_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_BOOTM_LEN=0x4000000
-CONFIG_CMD_DFU=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPT=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_REMOTEPROC=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_TIME=y
-CONFIG_CMD_FAT=y
-CONFIG_OF_CONTROL=y
-CONFIG_SPL_OF_CONTROL=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SPL_DM=y
-CONFIG_SPL_DM_SEQ_ALIAS=y
-CONFIG_REGMAP=y
-CONFIG_SPL_REGMAP=y
-CONFIG_SYSCON=y
-CONFIG_SPL_SYSCON=y
-CONFIG_SPL_OF_TRANSLATE=y
-CONFIG_CLK=y
-CONFIG_SPL_CLK=y
-CONFIG_SPL_CLK_CCF=y
-CONFIG_SPL_CLK_K3_PLL=y
-CONFIG_SPL_CLK_K3=y
-CONFIG_SYS_DFU_DATA_BUF_SIZE=0x40000
-CONFIG_DMA_CHANNELS=y
-CONFIG_TI_K3_NAVSS_UDMA=y
-CONFIG_TI_SCI_PROTOCOL=y
-CONFIG_DA8XX_GPIO=y
-CONFIG_DM_PCA953X=y
-CONFIG_DM_I2C=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_I2C_OMAP24XX=y
-CONFIG_DM_MAILBOX=y
-CONFIG_K3_SEC_PROXY=y
-CONFIG_FS_LOADER=y
-CONFIG_SPL_FS_LOADER=y
-CONFIG_SUPPORT_EMMC_BOOT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
-CONFIG_MMC_SDHCI=y
-CONFIG_SPL_MMC_SDHCI_ADMA=y
-CONFIG_MMC_SDHCI_AM654=y
-CONFIG_MTD=y
-CONFIG_DM_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_SHOW_PROGRESS=0
-CONFIG_CFI_FLASH=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SPI_FLASH_SFDP_SUPPORT=y
-CONFIG_SPI_FLASH_SOFT_RESET=y
-CONFIG_SPI_FLASH_SOFT_RESET_ON_BOOT=y
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_MT35XU=y
-CONFIG_PINCTRL=y
-# CONFIG_PINCTRL_GENERIC is not set
-CONFIG_SPL_PINCTRL=y
-# CONFIG_SPL_PINCTRL_GENERIC is not set
-CONFIG_PINCTRL_SINGLE=y
-CONFIG_POWER_DOMAIN=y
-CONFIG_TI_POWER_DOMAIN=y
-CONFIG_K3_SYSTEM_CONTROLLER=y
-CONFIG_REMOTEPROC_TI_K3_ARM64=y
-CONFIG_DM_RESET=y
-CONFIG_RESET_TI_SCI=y
-CONFIG_DM_SERIAL=y
-CONFIG_SOC_DEVICE=y
-CONFIG_SOC_DEVICE_TI_K3=y
-CONFIG_SOC_TI=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_CADENCE_QSPI=y
-CONFIG_HAS_CQSPI_REF_CLK=y
-CONFIG_CQSPI_REF_CLK=133333333
-CONFIG_SYSRESET=y
-CONFIG_SPL_SYSRESET=y
-CONFIG_SYSRESET_TI_SCI=y
-CONFIG_DM_THERMAL=y
-CONFIG_TIMER=y
-CONFIG_SPL_TIMER=y
-CONFIG_OMAP_TIMER=y
-CONFIG_USB=y
-CONFIG_DM_USB_GADGET=y
-CONFIG_SPL_DM_USB_GADGET=y
-CONFIG_USB_CDNS3=y
-CONFIG_USB_CDNS3_GADGET=y
-CONFIG_SPL_USB_CDNS3_GADGET=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0451
-CONFIG_USB_GADGET_PRODUCT_NUM=0x6168
-CONFIG_USB_GADGET_DOWNLOAD=y
-CONFIG_FS_EXT4=y
-CONFIG_FS_FAT_MAX_CLUSTSIZE=16384
-CONFIG_PANIC_HANG=y
-CONFIG_LIB_RATIONAL=y
-CONFIG_SPL_LIB_RATIONAL=y
-- 
2.34.1

More information about the U-Boot mailing list