[PATCH v2 2/2] mmc: tmio: Replace ifdeffery with IS_ENABLED/CONFIG_IS_ENABLED macros
Marek Vasut
marek.vasut+renesas at mailbox.org
Tue Feb 28 22:18:13 CET 2023
Instead of #if and #ifdef, use IS_ENABLED and CONFIG_IS_ENABLED macros.
This improves build test coverage. The CONFIG_SPL_BUILD must remain an
ifdef, as CONFIG_SPL_STACK may not always be defined, e.g. in U-Boot
proper build. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas at mailbox.org>
---
Cc: Jaehoon Chung <jh80.chung at samsung.com>
Cc: Peng Fan <peng.fan at nxp.com>
---
V2: - Rebase on 1/2
- Drop DM_REGULATOR check from struct tmio_sd_priv in tmio-common.h
---
drivers/mmc/tmio-common.c | 59 +++++++++++++++++++--------------------
drivers/mmc/tmio-common.h | 2 --
2 files changed, 29 insertions(+), 32 deletions(-)
diff --git a/drivers/mmc/tmio-common.c b/drivers/mmc/tmio-common.c
index 0b24a5a7bdb..d8b6a4a8821 100644
--- a/drivers/mmc/tmio-common.c
+++ b/drivers/mmc/tmio-common.c
@@ -369,22 +369,23 @@ static bool tmio_sd_addr_is_dmaable(struct mmc_data *data)
if (!IS_ALIGNED(addr, TMIO_SD_DMA_MINALIGN))
return false;
-#if defined(CONFIG_RCAR_GEN3)
- if (!(data->flags & MMC_DATA_READ) && !IS_ALIGNED(addr, 128))
- return false;
- /* Gen3 DMA has 32bit limit */
- if (sizeof(addr) > 4 && addr >> 32)
- return false;
-#endif
+ if (IS_ENABLED(CONFIG_RCAR_GEN3)) {
+ if (!(data->flags & MMC_DATA_READ) && !IS_ALIGNED(addr, 128))
+ return false;
+ /* Gen3 DMA has 32bit limit */
+ if (sizeof(addr) > 4 && addr >> 32)
+ return false;
+ }
-#if defined(CONFIG_ARCH_UNIPHIER) && !defined(CONFIG_ARM64) && \
- defined(CONFIG_SPL_BUILD)
- /*
- * For UniPhier ARMv7 SoCs, the stack is allocated in the locked ways
- * of L2, which is unreachable from the DMA engine.
- */
- if (addr < CONFIG_SPL_STACK)
- return false;
+#ifdef CONFIG_SPL_BUILD
+ if (IS_ENABLED(CONFIG_ARCH_UNIPHIER) && !CONFIG_IS_ENABLED(CONFIG_ARM64)) {
+ /*
+ * For UniPhier ARMv7 SoCs, the stack is allocated in locked
+ * ways of L2, which is unreachable from the DMA engine.
+ */
+ if (addr < CONFIG_SPL_STACK)
+ return false;
+ }
#endif
return true;
@@ -622,25 +623,22 @@ static void tmio_sd_set_clk_rate(struct tmio_sd_priv *priv, struct mmc *mmc)
static void tmio_sd_set_pins(struct udevice *dev)
{
__maybe_unused struct mmc *mmc = mmc_get_mmc_dev(dev);
-
-#ifdef CONFIG_DM_REGULATOR
struct tmio_sd_priv *priv = dev_get_priv(dev);
- if (priv->vqmmc_dev) {
+ if (CONFIG_IS_ENABLED(DM_REGULATOR) && priv->vqmmc_dev) {
if (mmc->signal_voltage == MMC_SIGNAL_VOLTAGE_180)
regulator_set_value(priv->vqmmc_dev, 1800000);
else
regulator_set_value(priv->vqmmc_dev, 3300000);
regulator_set_enable(priv->vqmmc_dev, true);
}
-#endif
-#ifdef CONFIG_PINCTRL
- if (mmc->signal_voltage == MMC_SIGNAL_VOLTAGE_180)
- pinctrl_select_state(dev, "state_uhs");
- else
- pinctrl_select_state(dev, "default");
-#endif
+ if (CONFIG_IS_ENABLED(PINCTRL)) {
+ if (mmc->signal_voltage == MMC_SIGNAL_VOLTAGE_180)
+ pinctrl_select_state(dev, "state_uhs");
+ else
+ pinctrl_select_state(dev, "default");
+ }
}
int tmio_sd_set_ios(struct udevice *dev)
@@ -734,11 +732,12 @@ int tmio_sd_probe(struct udevice *dev, u32 quirks)
if (!priv->regbase)
return -ENOMEM;
-#ifdef CONFIG_DM_REGULATOR
- device_get_supply_regulator(dev, "vqmmc-supply", &priv->vqmmc_dev);
- if (priv->vqmmc_dev)
- regulator_set_value(priv->vqmmc_dev, 3300000);
-#endif
+ if (CONFIG_IS_ENABLED(DM_REGULATOR)) {
+ device_get_supply_regulator(dev, "vqmmc-supply",
+ &priv->vqmmc_dev);
+ if (priv->vqmmc_dev)
+ regulator_set_value(priv->vqmmc_dev, 3300000);
+ }
ret = mmc_of_parse(dev, &plat->cfg);
if (ret < 0) {
diff --git a/drivers/mmc/tmio-common.h b/drivers/mmc/tmio-common.h
index 4d717d85dec..f489fb70766 100644
--- a/drivers/mmc/tmio-common.h
+++ b/drivers/mmc/tmio-common.h
@@ -133,9 +133,7 @@ struct tmio_sd_priv {
#define TMIO_SD_CAP_RCAR_UHS BIT(7) /* Renesas RCar UHS/SDR modes */
#define TMIO_SD_CAP_RCAR \
(TMIO_SD_CAP_RCAR_GEN2 | TMIO_SD_CAP_RCAR_GEN3)
-#ifdef CONFIG_DM_REGULATOR
struct udevice *vqmmc_dev;
-#endif
#if CONFIG_IS_ENABLED(CLK)
struct clk clk;
struct clk clkh;
--
2.39.2
More information about the U-Boot
mailing list