[RFC PATCH 2/2] sunxi: add R528/T113-s3/D1(s) DRAM initialisation code
Andre Przywara
andre.przywara at arm.com
Tue Jan 3 11:23:29 CET 2023
On Tue, 03 Jan 2023 10:43:20 +0800
Icenowy Zheng <uwu at icenowy.me> wrote:
Hi Icenowy,
> 在 2023-01-03星期二的 01:17 +0000，Andre Przywara写道：
> > The Allwinner R528/T113-s/D1/D1s SoCs all share the same die, so use
> > the
> > same DRAM initialisation code.
> > Make use of prior art here and lift some code from awboot[1], which
> > carried init code based on earlier decompilation efforts, but with a
> > GPL2 license tag.
> > This code has been heavily reworked and cleaned up, to match previous
> > DRAM routines for other SoCs, and also to be closer to U-Boot's
> > coding
> > style and support routines.
> > The actual DRAM chip timing parameters are included in the main file,
> > since they cover all DRAM types, and are protected by a new Kconfig
> > CONFIG_SUNXI_DRAM_TYPE symbol, which allows the compiler to pick only
> > the relevant settings, at build time.
> >
> > The relevant DRAM chips/board specific configuration parameters are
> > delivered via Kconfig, so this code here should work for all
> > supported
> > SoCs and DRAM chips combinations.
>
> The D1 DRAM controller should be similar to the R329 one, which I added
> (legacy) support at [1].
Thanks for the hint (and apologies for not replying to your comment
on IRC before).
So this one here is clearly an RFC. I found myself deeply in a "let
me fix this comment formatting" rabbit hole lately, so wanted to get this
out now, so that people can start looking at it. That's why I didn't
compare your driver with that code here yet. From a very brief look, yours
is much more compact, so there is indeed some hope the two can get merged.
But I doubt that I realistically find the time in the next weeks to
compare them carefully. Also this driver here has clearly some work left
(for instance naming all the registers).
So any help, contributions and comments to this topic are warmly welcomed.
Cheers,
Andre
> [1]
> https://patchwork.ozlabs.org/project/uboot/patch/20210722063015.421923-8-icenowy@sipeed.com/
>
> >
> > Signed-off-by: Andre Przywara <andre.przywara at arm.com>
> > ---
> > drivers/Makefile | 1 +
> > drivers/ram/Makefile | 2 +
> > drivers/ram/sunxi/Kconfig | 55 ++
> > drivers/ram/sunxi/Makefile | 4 +
> > drivers/ram/sunxi/dram_sun20i_d1.c | 1425
> > ++++++++++++++++++++++++++++
> > drivers/ram/sunxi/dram_sun20i_d1.h | 70 ++
> > 6 files changed, 1557 insertions(+)
> > create mode 100644 drivers/ram/sunxi/Makefile
> > create mode 100644 drivers/ram/sunxi/dram_sun20i_d1.c
> > create mode 100644 drivers/ram/sunxi/dram_sun20i_d1.h
> >
> > diff --git a/drivers/Makefile b/drivers/Makefile
> > index 6f1de58e003..6a0d1ec2ff0 100644
> > --- a/drivers/Makefile
> > +++ b/drivers/Makefile
> > @@ -52,6 +52,7 @@ obj-$(CONFIG_$(SPL_)ALTERA_SDRAM) += ddr/altera/
> > obj-$(CONFIG_ARCH_IMX8M) += ddr/imx/imx8m/
> > obj-$(CONFIG_IMX8ULP_DRAM) += ddr/imx/imx8ulp/
> > obj-$(CONFIG_ARCH_IMX9) += ddr/imx/imx9/
> > +obj-$(CONFIG_DRAM_SUN8I_R528) += ram/
> > obj-$(CONFIG_SPL_DM_RESET) += reset/
> > obj-$(CONFIG_SPL_MUSB_NEW) += usb/musb-new/
> > obj-$(CONFIG_SPL_USB_GADGET) += usb/gadget/
> > diff --git a/drivers/ram/Makefile b/drivers/ram/Makefile
> > index 5a39611349d..82686046f1d 100644
> > --- a/drivers/ram/Makefile
> > +++ b/drivers/ram/Makefile
> > @@ -21,4 +21,6 @@ obj-$(CONFIG_IMXRT_SDRAM) += imxrt_sdram.o
> >
> > obj-$(CONFIG_RAM_SIFIVE) += sifive/
> >
> > +obj-$(CONFIG_DRAM_SUN8I_R528) += sunxi/
> > +
> > obj-$(CONFIG_ARCH_OCTEON) += octeon/
> > diff --git a/drivers/ram/sunxi/Kconfig b/drivers/ram/sunxi/Kconfig
> > index 97e261de542..36875ddf22d 100644
> > --- a/drivers/ram/sunxi/Kconfig
> > +++ b/drivers/ram/sunxi/Kconfig
> > @@ -11,3 +11,58 @@ config DRAM_SUN8I_R528
> > default y if MACH_SUN8I_R528
> > help
> > Select this DRAM controller driver for the R528/T113s SoCs.
> > +
> > +config DRAM_SUNXI_ODT_EN
> > + hex "DRAM ODT EN parameter"
> > + default 0x1
> > + help
> > + ODT EN value from vendor DRAM settings.
> > +
> > +config DRAM_SUNXI_TPR0
> > + hex "DRAM TPR0 parameter"
> > + default 0x0
> > + help
> > + TPR0 value from vendor DRAM settings.
> > +
> > +config DRAM_SUNXI_TPR11
> > + hex "DRAM TPR11 parameter"
> > + default 0x0
> > + help
> > + TPR11 value from vendor DRAM settings.
> > +
> > +config DRAM_SUNXI_TPR12
> > + hex "DRAM TPR12 parameter"
> > + default 0x0
> > + help
> > + TPR12 value from vendor DRAM settings.
> > +
> > +config DRAM_SUNXI_TPR13
> > + hex "DRAM TPR13 parameter"
> > + default 0x0
> > + help
> > + TPR13 value from vendor DRAM settings. It tells which
> > features
> > + should be configured.
> > +
> > +choice
> > + prompt "DRAM chip type"
> > + default SUNXI_DRAM_DDR3 if DRAM_SUN8I_R528 || DRAM_SUN20I_D1
> > +
> > +config SUNXI_DRAM_DDR2
> > + bool "DDR2 chips"
> > +
> > +config SUNXI_DRAM_DDR3
> > + bool "DDR3 chips"
> > +
> > +config SUNXI_DRAM_LPDDR2
> > + bool "LPDDR2 chips"
> > +
> > +config SUNXI_DRAM_LPDDR3
> > + bool "LPDDR3 chips"
> > +endchoice
> > +
> > +config SUNXI_DRAM_TYPE
> > + int
> > + default 2 if SUNXI_DRAM_DDR2
> > + default 3 if SUNXI_DRAM_DDR3
> > + default 6 if SUNXI_DRAM_LPDDR2
> > + default 7 if SUNXI_DRAM_LPDDR3
> > diff --git a/drivers/ram/sunxi/Makefile b/drivers/ram/sunxi/Makefile
> > new file mode 100644
> > index 00000000000..d6fb2cf0b65
> > --- /dev/null
> > +++ b/drivers/ram/sunxi/Makefile
> > @@ -0,0 +1,4 @@
> > +# SPDX-License-Identifier: GPL-2.0+
> > +
> > +obj-$(CONFIG_DRAM_SUN20I_D1) += dram_sun20i_d1.o
> > +obj-$(CONFIG_DRAM_SUN8I_R528) += dram_sun20i_d1.o
> > diff --git a/drivers/ram/sunxi/dram_sun20i_d1.c
> > b/drivers/ram/sunxi/dram_sun20i_d1.c
> > new file mode 100644
> > index 00000000000..06b4cd2c70b
> > --- /dev/null
> > +++ b/drivers/ram/sunxi/dram_sun20i_d1.c
> > @@ -0,0 +1,1425 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Allwinner D1/D1s/R528/T113-sx DRAM initialisation
> > + *
> > + * As usual there is no documentation for the memory controller or
> > PHY IP
> > + * used here. The baseline of this code was lifted from awboot[1],
> > which
> > + * seems to be based on some form of de-compilation of some original
> > Allwinner
> > + * code bits (with a GPL2 license tag from the very beginning).
> > + * This version here is a reworked version, to match the U-Boot
> > coding style
> > + * and style of the other Allwinner DRAM drivers.
> > + *
> > + * [1] https://github.com/szemzoa/awboot.git
> > + */
> > +
> > +#include <asm/io.h>
> > +#include <common.h>
> > +#ifdef CONFIG_RAM
> > + #include <dm.h>
> > + #include <ram.h>
> > +#endif
> > +#include <linux/delay.h>
> > +
> > +#include "dram_sun20i_d1.h"
> > +
> > +#ifndef SUNXI_SID_BASE
> > +#define SUNXI_SID_BASE 0x3006200
> > +#endif
> > +
> > +static void sid_read_ldoB_cal(dram_para_t *para)
> > +{
> > + uint32_t reg;
> > +
> > + reg = (readl(SUNXI_SID_BASE + 0x1c) & 0xff00) >> 8;
> > +
> > + if (reg == 0)
> > + return;
> > +
> > + switch (para->dram_type) {
> > + case SUNXI_DRAM_TYPE_DDR2:
> > + break;
> > + case SUNXI_DRAM_TYPE_DDR3:
> > + if (reg > 0x20)
> > + reg -= 0x16;
> > + break;
> > + default:
> > + reg = 0;
> > + break;
> > + }
> > +
> > + clrsetbits_le32(0x3000150, 0xff00, reg << 8);
> > +}
> > +
> > +static void dram_voltage_set(dram_para_t *para)
> > +{
> > + int vol;
> > +
> > + switch (para->dram_type) {
> > + case SUNXI_DRAM_TYPE_DDR2:
> > + vol = 47;
> > + break;
> > + case SUNXI_DRAM_TYPE_DDR3:
> > + vol = 25;
> > + break;
> > + default:
> > + vol = 0;
> > + break;
> > + }
> > +
> > + clrsetbits_le32(0x3000150, 0x20ff00, vol << 8);
> > +
> > + udelay(1);
> > +
> > + sid_read_ldoB_cal(para);
> > +}
> > +
> > +static void dram_enable_all_master(void)
> > +{
> > + writel(~0, 0x3102020);
> > + writel(0xff, 0x3102024);
> > + writel(0xffff, 0x3102028);
> > + udelay(10);
> > +}
> > +
> > +static void dram_disable_all_master(void)
> > +{
> > + writel(1, 0x3102020);
> > + writel(0, 0x3102024);
> > + writel(0, 0x3102028);
> > + udelay(10);
> > +}
> > +
> > +static void eye_delay_compensation(dram_para_t *para) // s1
> > +{
> > + uint32_t delay;
> > + unsigned long ptr;
> > +
> > + // DATn0IOCR, n = 0...7
> > + delay = (para->dram_tpr11 & 0xf) << 9;
> > + delay |= (para->dram_tpr12 & 0xf) << 1;
> > + for (ptr = 0x3103310; ptr < 0x3103334; ptr += 4)
> > + setbits_le32(ptr, delay);
> > +
> > + // DATn1IOCR, n = 0...7
> > + delay = (para->dram_tpr11 & 0xf0) << 5;
> > + delay |= (para->dram_tpr12 & 0xf0) >> 3;
> > + for (ptr = 0x3103390; ptr != 0x31033b4; ptr += 4)
> > + setbits_le32(ptr, delay);
> > +
> > + // PGCR0: assert AC loopback FIFO reset
> > + clrbits_le32(0x3103100, 0x04000000);
> > +
> > + // ??
> > +
> > + delay = (para->dram_tpr11 & 0xf0000) >> 7;
> > + delay |= (para->dram_tpr12 & 0xf0000) >> 15;
> > + setbits_le32(0x3103334, delay);
> > + setbits_le32(0x3103338, delay);
> > +
> > + delay = (para->dram_tpr11 & 0xf00000) >> 11;
> > + delay |= (para->dram_tpr12 & 0xf00000) >> 19;
> > + setbits_le32(0x31033b4, delay);
> > + setbits_le32(0x31033b8, delay);
> > +
> > + setbits_le32(0x310333c, (para->dram_tpr11 & 0xf0000) << 9);
> > + setbits_le32(0x31033bc, (para->dram_tpr11 & 0xf00000) << 5);
> > +
> > + // PGCR0: release AC loopback FIFO reset
> > + setbits_le32(0x3103100, BIT(26));
> > +
> > + udelay(1);
> > +
> > + delay = (para->dram_tpr10 & 0xf0) << 4;
> > + for (ptr = 0x3103240; ptr != 0x310327c; ptr += 4)
> > + setbits_le32(ptr, delay);
> > + for (ptr = 0x3103228; ptr != 0x3103240; ptr += 4)
> > + setbits_le32(ptr, delay);
> > +
> > + setbits_le32(0x3103218, (para->dram_tpr10 & 0x0f) << 8);
> > + setbits_le32(0x310321c, (para->dram_tpr10 & 0x0f) << 8);
> > +
> > + setbits_le32(0x3103280, (para->dram_tpr10 & 0xf00) >> 4);
> > +}
> > +
> > +/*
> > + * Main purpose of the auto_set_timing routine seems to be to
> > calculate all
> > + * timing settings for the specific type of sdram used. Read
> > together with
> > + * an sdram datasheet for context on the various variables.
> > + */
> > +static void mctl_set_timing_params(dram_para_t *para)
> > +{
> > + /* DRAM_TPR0 */
> > + u8 tccd = 2;
> > + u8 tfaw;
> > + u8 trrd;
> > + u8 trcd;
> > + u8 trc;
> > +
> > + /* DRAM_TPR1 */
> > + u8 txp;
> > + u8 twtr;
> > + u8 trtp = 4;
> > + u8 twr;
> > + u8 trp;
> > + u8 tras;
> > +
> > + /* DRAM_TPR2 */
> > + u16 trefi;
> > + u16 trfc;
> > +
> > + u8 tcksrx;
> > + u8 tckesr;
> > + u8 trd2wr;
> > + u8 twr2rd;
> > + u8 trasmax;
> > + u8 twtp;
> > + u8 tcke;
> > + u8 tmod;
> > + u8 tmrd;
> > + u8 tmrw;
> > +
> > + u8 tcl;
> > + u8 tcwl;
> > + u8 t_rdata_en;
> > + u8 wr_latency;
> > +
> > + u32 mr0;
> > + u32 mr1;
> > + u32 mr2;
> > + u32 mr3;
> > +
> > + u32 tdinit0;
> > + u32 tdinit1;
> > + u32 tdinit2;
> > + u32 tdinit3;
> > +
> > + switch (CONFIG_SUNXI_DRAM_TYPE) {
> > + case SUNXI_DRAM_TYPE_DDR2:
> > + /* DRAM_TPR0 */
> > + tfaw = ns_to_t(50);
> > + trrd = ns_to_t(10);
> > + trcd = ns_to_t(20);
> > + trc = ns_to_t(65);
> > +
> > + /* DRAM_TPR1 */
> > + txp = 2;
> > + twtr = ns_to_t(8);
> > + twr = ns_to_t(15);
> > + trp = ns_to_t(15);
> > + tras = ns_to_t(45);
> > +
> > + /* DRAM_TRP2 */
> > + trfc = ns_to_t(328);
> > + trefi = ns_to_t(7800) / 32;
> > +
> > + trasmax = CONFIG_DRAM_CLK / 30;
> > + if (CONFIG_DRAM_CLK < 409) {
> > + t_rdata_en = 1;
> > + tcl = 3;
> > + mr0 = 0x06a3;
> > + } else {
> > + t_rdata_en = 2;
> > + tcl = 4;
> > + mr0 = 0x0e73;
> > + }
> > + tmrd = 2;
> > + twtp = twr + 5;
> > + tcksrx = 5;
> > + tckesr = 4;
> > + trd2wr = 4;
> > + tcke = 3;
> > + tmod = 12;
> > + wr_latency = 1;
> > + tmrw = 0;
> > + twr2rd = twtr + 5;
> > + tcwl = 0;
> > +
> > + mr1 = para->dram_mr1;
> > + mr2 = 0;
> > + mr3 = 0;
> > +
> > + tdinit0 = 200 * CONFIG_DRAM_CLK + 1;
> > + tdinit1 = 100 * CONFIG_DRAM_CLK / 1000 + 1;
> > + tdinit2 = 200 * CONFIG_DRAM_CLK + 1;
> > + tdinit3 = 1 * CONFIG_DRAM_CLK + 1;
> > +
> > + break;
> > + case SUNXI_DRAM_TYPE_DDR3:
> > + trfc = ns_to_t(350);
> > + trefi = ns_to_t(7800) / 32 + 1; //
> > XXX
> > +
> > + twtr = ns_to_t(8) + 2; // +
> > 2 ? XXX
> > + /* Only used by trd2wr calculation, which gets
> > discard below */
> > +// twr = max(ns_to_t(15), 2);
> > + trrd = max(ns_to_t(10), 2);
> > + txp = max(ns_to_t(10), 2);
> > +
> > + if (CONFIG_DRAM_CLK <= 800) {
> > + tfaw = ns_to_t(50);
> > + trcd = ns_to_t(15);
> > + trp = ns_to_t(15);
> > + trc = ns_to_t(53);
> > + tras = ns_to_t(38);
> > +
> > + mr0 = 0x1c70;
> > + mr2 = 0x18;
> > + tcl = 6;
> > + wr_latency = 2;
> > + tcwl = 4;
> > + t_rdata_en = 4;
> > + } else {
> > + tfaw = ns_to_t(35);
> > + trcd = ns_to_t(14);
> > + trp = ns_to_t(14);
> > + trc = ns_to_t(48);
> > + tras = ns_to_t(34);
> > +
> > + mr0 = 0x1e14;
> > + mr2 = 0x20;
> > + tcl = 7;
> > + wr_latency = 3;
> > + tcwl = 5;
> > + t_rdata_en = 5;
> > + }
> > +
> > + trasmax = CONFIG_DRAM_CLK / 30;
> > + twtp = tcwl + 2 + twtr; //
> > WL+BL/2+tWTR
> > + /* Gets overwritten below */
> > +// trd2wr = tcwl + 2 + twr; //
> > WL+BL/2+tWR
> > + twr2rd = tcwl + twtr; //
> > WL+tWTR
> > +
> > + tdinit0 = 500 * CONFIG_DRAM_CLK + 1; //
> > 500 us
> > + tdinit1 = 360 * CONFIG_DRAM_CLK / 1000 + 1;
> > // 360 ns
> > + tdinit2 = 200 * CONFIG_DRAM_CLK + 1; //
> > 200 us
> > + tdinit3 = 1 * CONFIG_DRAM_CLK + 1; //
> > 1 us
> > +
> > + mr1 = para->dram_mr1;
> > + mr3 = 0;
> > + tcke = 3;
> > + tcksrx = 5;
> > + tckesr = 4;
> > + if (((para->dram_tpr13 & 0xc) == 0x04) ||
> > CONFIG_DRAM_CLK < 912)
> > + trd2wr = 5;
> > + else
> > + trd2wr = 6;
> > +
> > + tmod = 12;
> > + tmrd = 4;
> > + tmrw = 0;
> > +
> > + break;
> > + case SUNXI_DRAM_TYPE_LPDDR2:
> > + tfaw = max(ns_to_t(50), 4);
> > + trrd = max(ns_to_t(10), 1);
> > + trcd = max(ns_to_t(24), 2);
> > + trc = ns_to_t(70);
> > + txp = ns_to_t(8);
> > + if (txp < 2) {
> > + txp++;
> > + twtr = 2;
> > + } else {
> > + twtr = txp;
> > + }
> > + twr = max(ns_to_t(15), 2);
> > + trp = ns_to_t(17);
> > + tras = ns_to_t(42);
> > + trefi = ns_to_t(3900) / 32;
> > + trfc = ns_to_t(210);
> > +
> > + trasmax = CONFIG_DRAM_CLK / 60;
> > + mr3 = para->dram_mr3;
> > + twtp = twr + 5;
> > + mr2 = 6;
> > + mr1 = 5;
> > + tcksrx = 5;
> > + tckesr = 5;
> > + trd2wr = 10;
> > + tcke = 2;
> > + tmod = 5;
> > + tmrd = 5;
> > + tmrw = 3;
> > + tcl = 4;
> > + wr_latency = 1;
> > + t_rdata_en = 1;
> > +
> > + tdinit0 = 200 * CONFIG_DRAM_CLK + 1;
> > + tdinit1 = 100 * CONFIG_DRAM_CLK / 1000 + 1;
> > + tdinit2 = 11 * CONFIG_DRAM_CLK + 1;
> > + tdinit3 = 1 * CONFIG_DRAM_CLK + 1;
> > + twr2rd = twtr + 5;
> > + tcwl = 2;
> > + mr1 = 195;
> > + mr0 = 0;
> > +
> > + break;
> > + case SUNXI_DRAM_TYPE_LPDDR3:
> > + tfaw = max(ns_to_t(50), 4);
> > + trrd = max(ns_to_t(10), 1);
> > + trcd = max(ns_to_t(24), 2);
> > + trc = ns_to_t(70);
> > + twtr = max(ns_to_t(8), 2);
> > + twr = max(ns_to_t(15), 2);
> > + trp = ns_to_t(17);
> > + tras = ns_to_t(42);
> > + trefi = ns_to_t(3900) / 32;
> > + trfc = ns_to_t(210);
> > + txp = twtr;
> > +
> > + trasmax = CONFIG_DRAM_CLK / 60;
> > + if (CONFIG_DRAM_CLK < 800) {
> > + tcwl = 4;
> > + wr_latency = 3;
> > + t_rdata_en = 6;
> > + mr2 = 12;
> > + } else {
> > + tcwl = 3;
> > + tcke = 6;
> > + wr_latency = 2;
> > + t_rdata_en = 5;
> > + mr2 = 10;
> > + }
> > + twtp = tcwl + 5;
> > + tcl = 7;
> > + mr3 = para->dram_mr3;
> > + tcksrx = 5;
> > + tckesr = 5;
> > + trd2wr = 13;
> > + tcke = 3;
> > + tmod = 12;
> > + tdinit0 = 400 * CONFIG_DRAM_CLK + 1;
> > + tdinit1 = 500 * CONFIG_DRAM_CLK / 1000 + 1;
> > + tdinit2 = 11 * CONFIG_DRAM_CLK + 1;
> > + tdinit3 = 1 * CONFIG_DRAM_CLK + 1;
> > + tmrd = 5;
> > + tmrw = 5;
> > + twr2rd = tcwl + twtr + 5;
> > + mr1 = 195;
> > + mr0 = 0;
> > +
> > + break;
> > + default:
> > + trfc = 128;
> > + trp = 6;
> > + trefi = 98;
> > + txp = 10;
> > + twr = 8;
> > + twtr = 3;
> > + tras = 14;
> > + tfaw = 16;
> > + trc = 20;
> > + trcd = 6;
> > + trrd = 3;
> > +
> > + twr2rd = 8; // 48(sp)
> > + tcksrx = 4; // t1
> > + tckesr = 3; // t4
> > + trd2wr = 4; // t6
> > + trasmax = 27; // t3
> > + twtp = 12; // s6
> > + tcke = 2; // s8
> > + tmod = 6; // t0
> > + tmrd = 2; // t5
> > + tmrw = 0; // a1
> > + tcwl = 3; // a5
> > + tcl = 3; // a0
> > + wr_latency = 1; // a7
> > + t_rdata_en = 1; // a4
> > + mr3 = 0; // s0
> > + mr2 = 0; // t2
> > + mr1 = 0; // s1
> > + mr0 = 0; // a3
> > + tdinit3 = 0; // 40(sp)
> > + tdinit2 = 0; // 32(sp)
> > + tdinit1 = 0; // 24(sp)
> > + tdinit0 = 0; // 16(sp)
> > +
> > + break;
> > + }
> > +
> > + /* Set mode registers */
> > + writel(mr0, 0x3103030);
> > + writel(mr1, 0x3103034);
> > + writel(mr2, 0x3103038);
> > + writel(mr3, 0x310303c);
> > + /* TODO: dram_odt_en is either 0x0 or 0x1, so right shift
> > looks weird */
> > + writel((para->dram_odt_en >> 4) & 0x3, 0x310302c);
> > +
> > + /* Set dram timing DRAMTMG0 - DRAMTMG5 */
> > + writel((twtp << 24) | (tfaw << 16) | (trasmax << 8) | (tras
> > << 0),
> > + 0x3103058);
> > + writel((txp << 16) | (trtp << 8) | (trc << 0),
> > + 0x310305c);
> > + writel((tcwl << 24) | (tcl << 16) | (trd2wr << 8) | (twr2rd
> > << 0),
> > + 0x3103060);
> > + writel((tmrw << 16) | (tmrd << 12) | (tmod << 0),
> > + 0x3103064);
> > + writel((trcd << 24) | (tccd << 16) | (trrd << 8) | (trp <<
> > 0),
> > + 0x3103068);
> > + writel((tcksrx << 24) | (tcksrx << 16) | (tckesr << 8) |
> > (tcke << 0),
> > + 0x310306c);
> > +
> > + /* Set dual rank timing */
> > + clrsetbits_le32(0x3103078, 0xf000ffff,
> > + (CONFIG_DRAM_CLK < 800) ? 0xf0006610 :
> > 0xf0007610);
> > +
> > + /* Set phy interface time PITMG0, PTR3, PTR4 */
> > + writel((0x2 << 24) | (t_rdata_en << 16) | BIT(8) |
> > (wr_latency << 0),
> > + 0x3103080);
> > + writel(((tdinit0 << 0) | (tdinit1 << 20)), 0x3103050);
> > + writel(((tdinit2 << 0) | (tdinit3 << 20)), 0x3103054);
> > +
> > + /* Set refresh timing and mode */
> > + writel((trefi << 16) | (trfc << 0), 0x3103090);
> > + writel((trefi << 15) & 0x0fff0000, 0x3103094);
> > +}
> > +
> > +// Purpose of this routine seems to be to initialize the PLL driving
> > +// the MBUS and sdram.
> > +//
> > +static int ccu_set_pll_ddr_clk(int index, dram_para_t *para)
> > +{
> > + unsigned int val, clk, n;
> > +
> > + if (para->dram_tpr13 & BIT(6))
> > + clk = para->dram_tpr9;
> > + else
> > + clk = para->dram_clk;
> > +
> > + // set VCO clock divider
> > + n = (clk * 2) / 24;
> > +
> > + val = readl(0x2001010);
> > + val &= 0xfff800fc; // clear dividers
> > + val |= (n - 1) << 8; // set PLL division
> > + val |= 0xc0000000; // enable PLL and LDO
> > + val &= 0xdfffffff;
> > + writel(val | 0x20000000, 0x2001010);
> > +
> > + // wait for PLL to lock
> > + while ((readl(0x2001010) & 0x10000000) == 0) {
> > + ;
> > + }
> > +
> > + udelay(20);
> > +
> > + // enable PLL output
> > + val = readl(0x2001000);
> > + val |= 0x08000000;
> > + writel(val, 0x2001000);
> > +
> > + // turn clock gate on
> > + val = readl(0x2001800);
> > + val &= 0xfcfffcfc; // select DDR clk source, n=1, m=1
> > + val |= 0x80000000; // turn clock on
> > + writel(val, 0x2001800);
> > +
> > + return n * 24;
> > +}
> > +
> > +// Main purpose of sys_init seems to be to initalise the clocks for
> > +// the sdram controller.
> > +//
> > +static void mctl_sys_init(dram_para_t *para)
> > +{
> > + // assert MBUS reset
> > + clrbits_le32(0x2001540, BIT(30));
> > +
> > + // turn off sdram clock gate, assert sdram reset
> > + clrbits_le32(0x200180c, 0x10001);
> > + clrsetbits_le32(0x2001800, BIT(31) | BIT(30), BIT(27));
> > + udelay(10);
> > +
> > + // set ddr pll clock
> > + para->dram_clk = ccu_set_pll_ddr_clk(0, para) / 2;
> > + udelay(100);
> > + dram_disable_all_master();
> > +
> > + // release sdram reset
> > + setbits_le32(0x200180c, BIT(16));
> > +
> > + // release MBUS reset
> > + setbits_le32(0x2001540, BIT(30));
> > + setbits_le32(0x2001800, BIT(30));
> > +
> > + udelay(5);
> > +
> > + // turn on sdram clock gate
> > + setbits_le32(0x200180c, BIT(0));
> > +
> > + // turn dram clock gate on, trigger sdr clock update
> > + setbits_le32(0x2001800, BIT(31) | BIT(27));
> > + udelay(5);
> > +
> > + // mCTL clock enable
> > + writel(0x8000, 0x310300c);
> > + udelay(10);
> > +}
> > +
> > +// The main purpose of this routine seems to be to copy an address
> > configuration
> > +// from the dram_para1 and dram_para2 fields to the PHY
> > configuration registers
> > +// (0x3102000, 0x3102004).
> > +//
> > +static void mctl_com_init(dram_para_t *para)
> > +{
> > + uint32_t val, width;
> > + unsigned long ptr;
> > + int i;
> > +
> > + // purpose ??
> > + clrsetbits_le32(0x3102008, 0x3f00, 0x2000);
> > +
> > + // set SDRAM type and word width
> > + val = readl(0x3102000) & ~0x00fff000;
> > + val |= (para->dram_type & 0x7) << 16; // DRAM type
> > + val |= (~para->dram_para2 & 0x1) << 12; // DQ width
> > + val |= BIT(22); // ??
> > + if (para->dram_type == SUNXI_DRAM_TYPE_LPDDR2 ||
> > + para->dram_type == SUNXI_DRAM_TYPE_LPDDR3) {
> > + val |= BIT(19); // type 6 and 7 must use 1T
> > + } else {
> > + if (para->dram_tpr13 & BIT(5))
> > + val |= BIT(19);
> > + }
> > + writel(val, 0x3102000);
> > +
> > + // init rank / bank / row for single/dual or two different
> > ranks
> > + if ((para->dram_para2 & BIT(8)) &&
> > + ((para->dram_para2 & 0xf000) != 0x1000))
> > + width = 32;
> > + else
> > + width = 16;
> > +
> > + ptr = 0x3102000;
> > + for (i = 0; i < width; i += 16) {
> > + val = readl(ptr) & 0xfffff000;
> > +
> > + val |= (para->dram_para2 >> 12) & 0x3; // rank
> > + val |= ((para->dram_para1 >> (i + 12)) << 2) & 0x4;
> > // bank - 2
> > + val |= (((para->dram_para1 >> (i + 4)) - 1) << 4) &
> > 0xff; // row - 1
> > +
> > + // convert from page size to column addr width - 3
> > + switch ((para->dram_para1 >> i) & 0xf) {
> > + case 8: val |= 0xa00; break;
> > + case 4: val |= 0x900; break;
> > + case 2: val |= 0x800; break;
> > + case 1: val |= 0x700; break;
> > + default: val |= 0x600; break;
> > + }
> > + writel(val, ptr);
> > + ptr += 4;
> > + }
> > +
> > + // set ODTMAP based on number of ranks in use
> > + val = (readl(0x3102000) & 0x1) ? 0x303 : 0x201;
> > + writel(val, 0x3103120);
> > +
> > + // set mctl reg 3c4 to zero when using half DQ
> > + if (para->dram_para2 & BIT(0))
> > + writel(0, 0x31033c4);
> > +
> > + // purpose ??
> > + if (para->dram_tpr4) {
> > + setbits_le32(0x3102000, (para->dram_tpr4 & 0x3) <<
> > 25);
> > + setbits_le32(0x3102004, (para->dram_tpr4 & 0x7fc) <<
> > 10);
> > + }
> > +}
> > +
> > +static const uint8_t ac_remapping_tables[][22] = {
> > + [0] = { 0 },
> > + [1] = { 1, 9, 3, 7, 8, 18, 4, 13, 5, 6, 10,
> > + 2, 14, 12, 0, 0, 21, 17, 20, 19, 11, 22 },
> > + [2] = { 4, 9, 3, 7, 8, 18, 1, 13, 2, 6, 10,
> > + 5, 14, 12, 0, 0, 21, 17, 20, 19, 11, 22 },
> > + [3] = { 1, 7, 8, 12, 10, 18, 4, 13, 5, 6, 3,
> > + 2, 9, 0, 0, 0, 21, 17, 20, 19, 11, 22 },
> > + [4] = { 4, 12, 10, 7, 8, 18, 1, 13, 2, 6, 3,
> > + 5, 9, 0, 0, 0, 21, 17, 20, 19, 11, 22 },
> > + [5] = { 13, 2, 7, 9, 12, 19, 5, 1, 6, 3, 4,
> > + 8, 10, 0, 0, 0, 21, 22, 18, 17, 11, 20 },
> > + [6] = { 3, 10, 7, 13, 9, 11, 1, 2, 4, 6, 8,
> > + 5, 12, 0, 0, 0, 20, 1, 0, 21, 22, 17 },
> > + [7] = { 3, 2, 4, 7, 9, 1, 17, 12, 18, 14, 13,
> > + 8, 15, 6, 10, 5, 19, 22, 16, 21, 20, 11 },
> > +};
> > +
> > +/*
> > + * This routine chooses one of several remapping tables for 22
> > lines.
> > + * It is unclear which lines are being remapped. It seems to pick
> > + * table cfg7 for the Nezha board.
> > + */
> > +static void mctl_phy_ac_remapping(dram_para_t *para)
> > +{
> > + const uint8_t *cfg;
> > + uint32_t fuse, val;
> > +
> > + /*
> > + * It is unclear whether the LPDDRx types don't need any
> > remapping,
> > + * or whether the original code just didn't provide tables.
> > + */
> > + if (para->dram_type != SUNXI_DRAM_TYPE_DDR2 &&
> > + para->dram_type != SUNXI_DRAM_TYPE_DDR3)
> > + return;
> > +
> > + fuse = (readl(SUNXI_SID_BASE + 0x28) & 0xf00) >> 8;
> > + debug("DDR efuse: 0x%x\n", fuse);
> > +
> > + if (para->dram_type == SUNXI_DRAM_TYPE_DDR2) {
> > + if (fuse == 15)
> > + return;
> > + cfg = ac_remapping_tables[6];
> > + } else {
> > + if (para->dram_tpr13 & 0xc0000) {
> > + cfg = ac_remapping_tables[7];
> > + } else {
> > + switch (fuse) {
> > + case 8: cfg = ac_remapping_tables[2]; break;
> > + case 9: cfg = ac_remapping_tables[3]; break;
> > + case 10: cfg = ac_remapping_tables[5]; break;
> > + case 11: cfg = ac_remapping_tables[4]; break;
> > + default:
> > + case 12: cfg = ac_remapping_tables[1]; break;
> > + case 13:
> > + case 14: cfg = ac_remapping_tables[0]; break;
> > + }
> > + }
> > + }
> > +
> > + val = (cfg[4] << 25) | (cfg[3] << 20) | (cfg[2] << 15) |
> > + (cfg[1] << 10) | (cfg[0] << 5);
> > + writel(val, 0x3102500);
> > +
> > + val = (cfg[10] << 25) | (cfg[9] << 20) | (cfg[8] << 15) |
> > + (cfg[ 7] << 10) | (cfg[6] << 5) | cfg[5];
> > + writel(val, 0x3102504);
> > +
> > + val = (cfg[15] << 20) | (cfg[14] << 15) | (cfg[13] << 10) |
> > + (cfg[12] << 5) | cfg[11];
> > + writel(val, 0x3102508);
> > +
> > + val = (cfg[21] << 25) | (cfg[20] << 20) | (cfg[19] << 15) |
> > + (cfg[18] << 10) | (cfg[17] << 5) | cfg[16];
> > + writel(val, 0x310250c);
> > +
> > + val = (cfg[4] << 25) | (cfg[3] << 20) | (cfg[2] << 15) |
> > + (cfg[1] << 10) | (cfg[0] << 5) | 1;
> > + writel(val, 0x3102500);
> > +}
> > +
> > +// Init the controller channel. The key part is placing commands in
> > the main
> > +// command register (PIR, 0x3103000) and checking command status
> > (PGSR0, 0x3103010).
> > +//
> > +static unsigned int mctl_channel_init(unsigned int ch_index,
> > dram_para_t *para)
> > +{
> > + unsigned int val, dqs_gating_mode;
> > +
> > + dqs_gating_mode = (para->dram_tpr13 & 0xc) >> 2;
> > +
> > + // set DDR clock to half of CPU clock
> > + clrsetbits_le32(0x310200c, 0xfff, (para->dram_clk / 2) - 1);
> > +
> > + // MRCTRL0 nibble 3 undocumented
> > + clrsetbits_le32(0x3103108, 0xf00, 0x300);
> > +
> > + if (para->dram_odt_en)
> > + val = 0;
> > + else
> > + val = BIT(5);
> > +
> > + // DX0GCR0
> > + if (para->dram_clk > 672)
> > + clrsetbits_le32(0x3103344, 0xf63e, val);
> > + else
> > + clrsetbits_le32(0x3103344, 0xf03e, val);
> > +
> > + // DX1GCR0
> > + if (para->dram_clk > 672) {
> > + setbits_le32(0x3103344, 0x400);
> > + clrsetbits_le32(0x31033c4, 0xf63e, val);
> > + } else {
> > + clrsetbits_le32(0x31033c4, 0xf03e, val);
> > + }
> > +
> > + // 0x3103208 undocumented
> > + setbits_le32(0x3103208, BIT(1));
> > +
> > + eye_delay_compensation(para);
> > +
> > + // set PLL SSCG ?
> > + val = readl(0x3103108);
> > + if (dqs_gating_mode == 1) {
> > + clrsetbits_le32(0x3103108, 0xc0, 0);
> > + clrbits_le32(0x31030bc, 0x107);
> > + } else if (dqs_gating_mode == 2) {
> > + clrsetbits_le32(0x3103108, 0xc0, 0x80);
> > +
> > + clrsetbits_le32(0x31030bc, 0x107,
> > + (((para->dram_tpr13 >> 16) & 0x1f) -
> > 2) | 0x100);
> > + clrsetbits_le32(0x310311c, BIT(31), BIT(27));
> > + } else {
> > + clrbits_le32(0x3103108, 0x40);
> > + udelay(10);
> > + setbits_le32(0x3103108, 0xc0);
> > + }
> > +
> > + if (para->dram_type == SUNXI_DRAM_TYPE_LPDDR2 ||
> > + para->dram_type == SUNXI_DRAM_TYPE_LPDDR3) {
> > + if (dqs_gating_mode == 1)
> > + clrsetbits_le32(0x310311c, 0x080000c0,
> > 0x80000000);
> > + else
> > + clrsetbits_le32(0x310311c, 0x77000000,
> > 0x22000000);
> > + }
> > +
> > + clrsetbits_le32(0x31030c0, 0x0fffffff,
> > + (para->dram_para2 & BIT(12)) ? 0x03000001 :
> > 0x01000007);
> > +
> > + if (readl(0x70005d4) & (1 << 16)) {
> > + clrbits_le32(0x7010250, 0x2);
> > + udelay(10);
> > + }
> > +
> > + // Set ZQ config
> > + clrsetbits_le32(0x3103140, 0x3ffffff,
> > + (para->dram_zq & 0x00ffffff) | BIT(25));
> > +
> > + // Initialise DRAM controller
> > + if (dqs_gating_mode == 1) {
> > + //writel(0x52, 0x3103000); // prep PHY reset + PLL
> > init + z-cal
> > + writel(0x53, 0x3103000); // Go
> > +
> > + while ((readl(0x3103010) & 0x1) == 0) {
> > + } // wait for IDONE
> > + udelay(10);
> > +
> > + // 0x520 = prep DQS gating + DRAM init + d-cal
> > + if (para->dram_type == SUNXI_DRAM_TYPE_DDR3)
> > + writel(0x5a0, 0x3103000); // +
> > DRAM reset
> > + else
> > + writel(0x520, 0x3103000);
> > + } else {
> > + if ((readl(0x70005d4) & (1 << 16)) == 0) {
> > + // prep DRAM init + PHY reset + d-cal + PLL
> > init + z-cal
> > + if (para->dram_type == SUNXI_DRAM_TYPE_DDR3)
> > + writel(0x1f2, 0x3103000); // +
> > DRAM reset
> > + else
> > + writel(0x172, 0x3103000);
> > + } else {
> > + // prep PHY reset + d-cal + z-cal
> > + writel(0x62, 0x3103000);
> > + }
> > + }
> > +
> > + setbits_le32(0x3103000, 0x1); // GO
> > +
> > + udelay(10);
> > + while ((readl(0x3103010) & 0x1) == 0) {
> > + } // wait for IDONE
> > +
> > + if (readl(0x70005d4) & (1 << 16)) {
> > + clrsetbits_le32(0x310310c, 0x06000000, 0x04000000);
> > + udelay(10);
> > +
> > + setbits_le32(0x3103004, 0x1);
> > +
> > + while ((readl(0x3103018) & 0x7) != 0x3) {
> > + }
> > +
> > + clrbits_le32(0x7010250, 0x1);
> > + udelay(10);
> > +
> > + clrbits_le32(0x3103004, 0x1);
> > +
> > + while ((readl(0x3103018) & 0x7) != 0x1) {
> > + }
> > +
> > + udelay(15);
> > +
> > + if (dqs_gating_mode == 1) {
> > + clrbits_le32(0x3103108, 0xc0);
> > + clrsetbits_le32(0x310310c, 0x06000000,
> > 0x02000000);
> > + udelay(1);
> > + writel(0x401, 0x3103000);
> > +
> > + while ((readl(0x3103010) & 0x1) == 0) {
> > + }
> > + }
> > + }
> > +
> > + // Check for training error
> > + if (readl(0x3103010) & BIT(20)) {
> > + printf("ZQ calibration error, check external 240 ohm
> > resistor\n");
> > + return 0;
> > + }
> > +
> > + // STATR = Zynq STAT? Wait for status 'normal'?
> > + while ((readl(0x3103018) & 0x1) == 0) {
> > + }
> > +
> > + setbits_le32(0x310308c, BIT(31));
> > + udelay(10);
> > + clrbits_le32(0x310308c, BIT(31));
> > + udelay(10);
> > + setbits_le32(0x3102014, BIT(31));
> > + udelay(10);
> > +
> > + clrbits_le32(0x310310c, 0x06000000);
> > +
> > + if (dqs_gating_mode == 1)
> > + clrsetbits_le32(0x310311c, 0xc0, 0x40);
> > +
> > + return 1;
> > +}
> > +
> > +static unsigned int calculate_rank_size(uint32_t regval)
> > +{
> > + unsigned int bits;
> > +
> > + bits = (regval >> 8) & 0xf; /* page size - 3 */
> > + bits += (regval >> 4) & 0xf; /* row width - 1 */
> > + bits += (regval >> 2) & 0x3; /* bank count - 2 */
> > + bits -= 14; /* 1MB = 20 bits, minus above
> > 6 = 14 */
> > +
> > + return 1U << bits;
> > +}
> > +
> > +/*
> > + * The below routine reads the dram config registers and extracts
> > + * the number of address bits in each rank available. It then
> > calculates
> > + * total memory size in MB.
> > + */
> > +static unsigned int DRAMC_get_dram_size(void)
> > +{
> > + uint32_t val;
> > + unsigned int size;
> > +
> > + val = readl(0x3102000); /* MC_WORK_MODE0 */
> > + size = calculate_rank_size(val);
> > + if ((val & 0x3) == 0) /* single rank? */
> > + return size;
> > +
> > + val = readl(0x3102004); /* MC_WORK_MODE1 */
> > + if ((val & 0x3) == 0) /* two identical ranks? */
> > + return size * 2;
> > +
> > + /* add sizes of both ranks */
> > + return size + calculate_rank_size(val);
> > +}
> > +
> > +/*
> > + * The below routine reads the command status register to extract
> > + * DQ width and rank count. This follows the DQS training command in
> > + * channel_init. If error bit 22 is reset, we have two ranks and
> > full DQ.
> > + * If there was an error, figure out whether it was half DQ, single
> > rank,
> > + * or both. Set bit 12 and 0 in dram_para2 with the results.
> > + */
> > +static int dqs_gate_detect(dram_para_t *para)
> > +{
> > + uint32_t dx0, dx1;
> > +
> > + if ((readl(0x3103010) & BIT(22)) == 0) {
> > + para->dram_para2 = (para->dram_para2 & ~0xf) |
> > BIT(12);
> > + debug("dual rank and full DQ\n");
> > +
> > + return 1;
> > + }
> > +
> > + dx0 = (readl(0x03103348) & 0x3000000) >> 24;
> > + if (dx0 == 0) {
> > + para->dram_para2 = (para->dram_para2 & ~0xf) |
> > 0x1001;
> > + debug("dual rank and half DQ\n");
> > +
> > + return 1;
> > + }
> > +
> > + if (dx0 == 2) {
> > + dx1 = (readl(0x031033c8) & 0x3000000) >> 24;
> > + if (dx1 == 2) {
> > + para->dram_para2 = para->dram_para2 &
> > ~0xf00f;
> > + debug("single rank and full DQ\n");
> > + } else {
> > + para->dram_para2 = (para->dram_para2 &
> > ~0xf00f) | BIT(0);
> > + debug("single rank and half DQ\n");
> > + }
> > +
> > + return 1;
> > + }
> > +
> > + if ((para->dram_tpr13 & BIT(29)) == 0)
> > + return 0;
> > +
> > + debug("DX0 state: %d\n", dx0);
> > + debug("DX1 state: %d\n", dx1);
> > +
> > + return 0;
> > +}
> > +
> > +static int dramc_simple_wr_test(unsigned int mem_mb, int len)
> > +{
> > + unsigned int offs = (mem_mb / 2) << 18; // half of
> > memory size
> > + unsigned int patt1 = 0x01234567;
> > + unsigned int patt2 = 0xfedcba98;
> > + unsigned int *addr, v1, v2, i;
> > +
> > + addr = (unsigned int *)CONFIG_SYS_SDRAM_BASE;
> > + for (i = 0; i != len; i++, addr++) {
> > + writel(patt1 + i, (unsigned long)addr);
> > + writel(patt2 + i, (unsigned long)(addr + offs));
> > + }
> > +
> > + addr = (unsigned int *)CONFIG_SYS_SDRAM_BASE;
> > + for (i = 0; i != len; i++) {
> > + v1 = readl((unsigned long)(addr + i));
> > + v2 = patt1 + i;
> > + if (v1 != v2) {
> > + printf("DRAM: simple test FAIL\n");
> > + printf("%x != %x at address %p\n", v1, v2,
> > addr + i);
> > + return 1;
> > + }
> > + v1 = readl((unsigned long)(addr + offs + i));
> > + v2 = patt2 + i;
> > + if (v1 != v2) {
> > + printf("DRAM: simple test FAIL\n");
> > + printf("%x != %x at address %p\n", v1, v2,
> > addr + offs + i);
> > + return 1;
> > + }
> > + }
> > +
> > + debug("DRAM: simple test OK\n");
> > + return 0;
> > +}
> > +
> > +// Set the Vref mode for the controller
> > +//
> > +static void mctl_vrefzq_init(dram_para_t *para)
> > +{
> > + if (para->dram_tpr13 & BIT(17))
> > + return;
> > +
> > + clrsetbits_le32(0x3103110, 0x7f7f7f7f, para->dram_tpr5);
> > +
> > + // IOCVR1
> > + if ((para->dram_tpr13 & BIT(16)) == 0)
> > + clrsetbits_le32(0x3103114, 0x7f, para->dram_tpr6 &
> > 0x7f);
> > +}
> > +
> > +// Perform an init of the controller. This is actually done 3 times.
> > The first
> > +// time to establish the number of ranks and DQ width. The second
> > time to
> > +// establish the actual ram size. The third time is final one, with
> > the final
> > +// settings.
> > +//
> > +static int mctl_core_init(dram_para_t *para)
> > +{
> > + mctl_sys_init(para);
> > +
> > + mctl_vrefzq_init(para);
> > +
> > + mctl_com_init(para);
> > +
> > + mctl_phy_ac_remapping(para);
> > +
> > + mctl_set_timing_params(para);
> > +
> > + return mctl_channel_init(0, para);
> > +}
> > +
> > +/*
> > + * This routine sizes a DRAM device by cycling through address lines
> > and
> > + * figuring out if they are connected to a real address line, or if
> > the
> > + * address is a mirror.
> > + * First the column and bank bit allocations are set to low values
> > (2 and 9
> > + * address lines). Then a maximum allocation (16 lines) is set for
> > rows and
> > + * this is tested.
> > + * Next the BA2 line is checked. This seems to be placed above the
> > column,
> > + * BA0-1 and row addresses. Finally, the column address is allocated
> > 13 lines
> > + * and these are tested. The results are placed in dram_para1 and
> > dram_para2.
> > + */
> > +static int auto_scan_dram_size(dram_para_t *para)
> > +{
> > + unsigned int rval, i, j, rank, maxrank, offs;
> > + unsigned int shft;
> > + unsigned long ptr, mc_work_mode, chk;
> > +
> > + if (mctl_core_init(para) == 0) {
> > + printf("DRAM initialisation error : 0\n");
> > + return 0;
> > + }
> > +
> > + maxrank = (para->dram_para2 & 0xf000) ? 2 : 1;
> > + mc_work_mode = 0x3102000;
> > + offs = 0;
> > +
> > + /* write test pattern */
> > + for (i = 0, ptr = CONFIG_SYS_SDRAM_BASE; i < 64; i++, ptr +=
> > 4)
> > + writel((i & 0x1) ? ptr : ~ptr, ptr);
> > +
> > + for (rank = 0; rank < maxrank;) {
> > + /* set row mode */
> > + clrsetbits_le32(mc_work_mode, 0xf0c, 0x6f0);
> > + udelay(1);
> > +
> > + // Scan per address line, until address wraps (i.e.
> > see shadow)
> > + for (i = 11; i < 17; i++) {
> > + chk = CONFIG_SYS_SDRAM_BASE + (1U << (i +
> > 11));
> > + ptr = CONFIG_SYS_SDRAM_BASE;
> > + for (j = 0; j < 64; j++) {
> > + if (readl(chk) != ((j & 1) ? ptr :
> > ~ptr))
> > + break;
> > + ptr += 4;
> > + chk += 4;
> > + }
> > + if (j == 64)
> > + break;
> > + }
> > + if (i > 16)
> > + i = 16;
> > + debug("rank %d row = %d\n", rank, i);
> > +
> > + /* Store rows in para 1 */
> > + shft = offs + 4;
> > + rval = para->dram_para1;
> > + rval &= ~(0xff << shft);
> > + rval |= i << shft;
> > + para->dram_para1 = rval;
> > +
> > + if (rank == 1) /* Set bank mode for rank0 */
> > + clrsetbits_le32(0x3102000, 0xffc, 0x6a4);
> > +
> > + /* Set bank mode for current rank */
> > + clrsetbits_le32(mc_work_mode, 0xffc, 0x6a4);
> > + udelay(1);
> > +
> > + // Test if bit A23 is BA2 or mirror XXX A22?
> > + chk = CONFIG_SYS_SDRAM_BASE + (1U << 22);
> > + ptr = CONFIG_SYS_SDRAM_BASE;
> > + for (i = 0, j = 0; i < 64; i++) {
> > + if (readl(chk) != ((i & 1) ? ptr : ~ptr)) {
> > + j = 1;
> > + break;
> > + }
> > + ptr += 4;
> > + chk += 4;
> > + }
> > +
> > + debug("rank %d bank = %d\n", rank, (j + 1) << 2); /*
> > 4 or 8 */
> > +
> > + /* Store banks in para 1 */
> > + shft = 12 + offs;
> > + rval = para->dram_para1;
> > + rval &= ~(0xf << shft);
> > + rval |= j << shft;
> > + para->dram_para1 = rval;
> > +
> > + if (rank == 1) /* Set page mode for rank0 */
> > + clrsetbits_le32(0x3102000, 0xffc, 0xaa0);
> > +
> > + /* Set page mode for current rank */
> > + clrsetbits_le32(mc_work_mode, 0xffc, 0xaa0);
> > + udelay(1);
> > +
> > + // Scan per address line, until address wraps (i.e.
> > see shadow)
> > + for (i = 9; i < 14; i++) {
> > + chk = CONFIG_SYS_SDRAM_BASE + (1U << i);
> > + ptr = CONFIG_SYS_SDRAM_BASE;
> > + for (j = 0; j < 64; j++) {
> > + if (readl(chk) != ((j & 1) ? ptr :
> > ~ptr))
> > + break;
> > + ptr += 4;
> > + chk += 4;
> > + }
> > + if (j == 64)
> > + break;
> > + }
> > + if (i > 13)
> > + i = 13;
> > +
> > + unsigned int pgsize = (i == 9) ? 0 : (1 << (i - 10));
> > + debug("rank %d page size = %d KB\n", rank, pgsize);
> > +
> > + /* Store page size */
> > + shft = offs;
> > + rval = para->dram_para1;
> > + rval &= ~(0xf << shft);
> > + rval |= pgsize << shft;
> > + para->dram_para1 = rval;
> > +
> > + // Move to next rank
> > + rank++;
> > + if (rank != maxrank) {
> > + if (rank == 1) {
> > + /* MC_WORK_MODE */
> > + clrsetbits_le32(0x3202000, 0xffc,
> > 0x6f0);
> > +
> > + /* MC_WORK_MODE2 */
> > + clrsetbits_le32(0x3202004, 0xffc,
> > 0x6f0);
> > + }
> > + /* store rank1 config in upper half of para1
> > */
> > + offs += 16;
> > + mc_work_mode += 4; /* move to
> > MC_WORK_MODE2 */
> > + }
> > + }
> > + if (maxrank == 2) {
> > + para->dram_para2 &= 0xfffff0ff;
> > + /* note: rval is equal to para->dram_para1 here */
> > + if ((rval & 0xffff) == (rval >> 16)) {
> > + debug("rank1 config same as rank0\n");
> > + } else {
> > + para->dram_para2 |= BIT(8);
> > + debug("rank1 config different from rank0\n");
> > + }
> > + }
> > +
> > + return 1;
> > +}
> > +
> > +/*
> > + * This routine sets up parameters with dqs_gating_mode equal to 1
> > and two
> > + * ranks enabled. It then configures the core and tests for 1 or 2
> > ranks and
> > + * full or half DQ width. It then resets the parameters to the
> > original values.
> > + * dram_para2 is updated with the rank and width findings.
> > + */
> > +static int auto_scan_dram_rank_width(dram_para_t *para)
> > +{
> > + unsigned int s1 = para->dram_tpr13;
> > + unsigned int s2 = para->dram_para1;
> > +
> > + para->dram_para1 = 0x00b000b0;
> > + para->dram_para2 = (para->dram_para2 & ~0xf) | BIT(12);
> > +
> > + /* set DQS probe mode */
> > + para->dram_tpr13 = (para->dram_tpr13 & ~0x8) | BIT(2) |
> > BIT(0);
> > +
> > + mctl_core_init(para);
> > +
> > + if (readl(0x3103010) & BIT(20))
> > + return 0;
> > +
> > + if (dqs_gate_detect(para) == 0)
> > + return 0;
> > +
> > + para->dram_tpr13 = s1;
> > + para->dram_para1 = s2;
> > +
> > + return 1;
> > +}
> > +
> > +/*
> > + * This routine determines the SDRAM topology. It first establishes
> > the number
> > + * of ranks and the DQ width. Then it scans the SDRAM address lines
> > to establish
> > + * the size of each rank. It then updates dram_tpr13 to reflect that
> > the sizes
> > + * are now known: a re-init will not repeat the autoscan.
> > + */
> > +static int auto_scan_dram_config(dram_para_t *para)
> > +{
> > + if (((para->dram_tpr13 & BIT(14)) == 0) &&
> > + (auto_scan_dram_rank_width(para) == 0)) {
> > + printf("ERROR: auto scan dram rank & width
> > failed\n");
> > + return 0;
> > + }
> > +
> > + if (((para->dram_tpr13 & BIT(0)) == 0) &&
> > + (auto_scan_dram_size(para) == 0)) {
> > + printf("ERROR: auto scan dram size failed\n");
> > + return 0;
> > + }
> > +
> > + if ((para->dram_tpr13 & BIT(15)) == 0)
> > + para->dram_tpr13 |= BIT(14) | BIT(13) | BIT(1) |
> > BIT(0);
> > +
> > + return 1;
> > +}
> > +
> > +int init_DRAM(int type, dram_para_t *para)
> > +{
> > + u32 rc, mem_size_mb;
> > +
> > + debug("DRAM BOOT DRIVE INFO: %s\n", "V0.24");
> > + debug("DRAM CLK = %d MHz\n", para->dram_clk);
> > + debug("DRAM Type = %d (2:DDR2,3:DDR3)\n", para->dram_type);
> > + if ((para->dram_odt_en & 0x1) == 0)
> > + debug("DRAMC read ODT off\n");
> > + else
> > + debug("DRAMC ZQ value: 0x%x\n", para->dram_zq);
> > +
> > + /* Test ZQ status */
> > + if (para->dram_tpr13 & BIT(16)) {
> > + debug("DRAM only have internal ZQ\n");
> > + setbits_le32(0x3000160, BIT(8));
> > + writel(0, 0x3000168);
> > + udelay(10);
> > + } else {
> > + clrbits_le32(0x3000160, 0x3);
> > + writel(para->dram_tpr13 & BIT(16), 0x7010254);
> > + udelay(10);
> > + clrsetbits_le32(0x3000160, 0x108, BIT(1));
> > + udelay(10);
> > + setbits_le32(0x3000160, BIT(0));
> > + udelay(20);
> > + debug("ZQ value = 0x%x\n", readl(0x300016c));
> > + }
> > +
> > + dram_voltage_set(para);
> > +
> > + /* Set SDRAM controller auto config */
> > + if ((para->dram_tpr13 & BIT(0)) == 0) {
> > + if (auto_scan_dram_config(para) == 0) {
> > + printf("auto_scan_dram_config() FAILED\n");
> > + return 0;
> > + }
> > + }
> > +
> > + /* report ODT */
> > + rc = para->dram_mr1;
> > + if ((rc & 0x44) == 0)
> > + debug("DRAM ODT off\n");
> > + else
> > + debug("DRAM ODT value: 0x%x\n", rc);
> > +
> > + /* Init core, final run */
> > + if (mctl_core_init(para) == 0) {
> > + printf("DRAM initialisation error: 1\n");
> > + return 0;
> > + }
> > +
> > + /* Get SDRAM size */
> > + /* TODO: who ever puts a negative number in the top half? */
> > + rc = para->dram_para2;
> > + if (rc & BIT(31)) {
> > + rc = (rc >> 16) & ~BIT(15);
> > + } else {
> > + rc = DRAMC_get_dram_size();
> > + debug("DRAM: size = %dMB\n", rc);
> > + para->dram_para2 = (para->dram_para2 & 0xffffU) | rc
> > << 16;
> > + }
> > + mem_size_mb = rc;
> > +
> > + /* Purpose ?? */
> > + if (para->dram_tpr13 & BIT(30)) {
> > + rc = para->dram_tpr8;
> > + if (rc == 0)
> > + rc = 0x10000200;
> > + writel(rc, 0x31030a0);
> > + writel(0x40a, 0x310309c);
> > + setbits_le32(0x3103004, BIT(0));
> > + debug("Enable Auto SR\n");
> > + } else {
> > + clrbits_le32(0x31030a0, 0xffff);
> > + clrbits_le32(0x3103004, 0x1);
> > + }
> > +
> > + /* Purpose ?? */
> > + if (para->dram_tpr13 & BIT(9)) {
> > + clrsetbits_le32(0x3103100, 0xf000, 0x5000);
> > + } else {
> > + if (para->dram_type != SUNXI_DRAM_TYPE_LPDDR2)
> > + clrbits_le32(0x3103100, 0xf000);
> > + }
> > +
> > + setbits_le32(0x3103140, BIT(31));
> > +
> > + /* CHECK: is that really writing to a different register? */
> > + if (para->dram_tpr13 & BIT(8))
> > + writel(readl(0x3103140) | 0x300, 0x31030b8);
> > +
> > + if (para->dram_tpr13 & BIT(16))
> > + clrbits_le32(0x3103108, BIT(13));
> > + else
> > + setbits_le32(0x3103108, BIT(13));
> > +
> > + /* Purpose ?? */
> > + if (para->dram_type == SUNXI_DRAM_TYPE_LPDDR3)
> > + clrsetbits_le32(0x310307c, 0xf0000, 0x1000);
> > +
> > + dram_enable_all_master();
> > + if (para->dram_tpr13 & BIT(28)) {
> > + if ((readl(0x70005d4) & BIT(16)) ||
> > + dramc_simple_wr_test(mem_size_mb, 4096))
> > + return 0;
> > + }
> > +
> > + return mem_size_mb;
> > +}
> > +
> > +unsigned long sunxi_dram_init(void)
> > +{
> > + dram_para_t para = {
> > + .dram_clk = CONFIG_DRAM_CLK,
> > + .dram_type = CONFIG_SUNXI_DRAM_TYPE,
> > + .dram_zq = CONFIG_DRAM_ZQ,
> > + .dram_odt_en = CONFIG_DRAM_SUNXI_ODT_EN,
> > + .dram_para1 = 0x000010d2,
> > + .dram_para2 = 0,
> > + .dram_mr0 = 0x1c70,
> > + .dram_mr1 = 0x42,
> > + .dram_mr2 = 0x18,
> > + .dram_mr3 = 0,
> > + .dram_tpr0 = 0x004a2195,
> > + .dram_tpr1 = 0x02423190,
> > + .dram_tpr2 = 0x0008b061,
> > + .dram_tpr3 = 0xb4787896, // unused
> > + .dram_tpr4 = 0,
> > + .dram_tpr5 = 0x48484848,
> > + .dram_tpr6 = 0x00000048,
> > + .dram_tpr7 = 0x1620121e, // unused
> > + .dram_tpr8 = 0,
> > + .dram_tpr9 = 0, // clock?
> > + .dram_tpr10 = 0,
> > + .dram_tpr11 = CONFIG_DRAM_SUNXI_TPR11,
> > + .dram_tpr12 = CONFIG_DRAM_SUNXI_TPR12,
> > + .dram_tpr13 = CONFIG_DRAM_SUNXI_TPR13,
> > + };
> > +
> > + return init_DRAM(0, ¶) * 1024UL * 1024;
> > +};
> > +
> > +#ifdef CONFIG_RAM /* using the driver model */
> > +struct sunxi_ram_priv {
> > + size_t size;
> > +};
> > +
> > +static int sunxi_ram_probe(struct udevice *dev)
> > +{
> > + struct sunxi_ram_priv *priv = dev_get_priv(dev);
> > + unsigned long dram_size;
> > +
> > + debug("%s: %s: probing\n", __func__, dev->name);
> > +
> > + dram_size = sunxi_dram_init();
> > + if (!dram_size) {
> > + printf("DRAM init failed: %d\n", ret);
> > + return -ENODEV;
> > + }
> > +
> > + priv->size = dram_size;
> > +
> > + return 0;
> > +}
> > +
> > +static int sunxi_ram_get_info(struct udevice *dev, struct ram_info
> > *info)
> > +{
> > + struct sunxi_ram_priv *priv = dev_get_priv(dev);
> > +
> > + debug("%s: %s: getting info\n", __func__, dev->name);
> > +
> > + info->base = CONFIG_SYS_SDRAM_BASE;
> > + info->size = priv->size;
> > +
> > + return 0;
> > +}
> > +
> > +static struct ram_ops sunxi_ram_ops = {
> > + .get_info = sunxi_ram_get_info,
> > +};
> > +
> > +static const struct udevice_id sunxi_ram_ids[] = {
> > + { .compatible = "allwinner,sun20i-d1-mbus" },
> > + { }
> > +};
> > +
> > +U_BOOT_DRIVER(sunxi_ram) = {
> > + .name = "sunxi_ram",
> > + .id = UCLASS_RAM,
> > + .of_match = sunxi_ram_ids,
> > + .ops = &sunxi_ram_ops,
> > + .probe = sunxi_ram_probe,
> > + .priv_auto = sizeof(struct sunxi_ram_priv),
> > +};
> > +#endif /* CONFIG_RAM (using driver model) */
> > diff --git a/drivers/ram/sunxi/dram_sun20i_d1.h
> > b/drivers/ram/sunxi/dram_sun20i_d1.h
> > new file mode 100644
> > index 00000000000..89aac9dadef
> > --- /dev/null
> > +++ b/drivers/ram/sunxi/dram_sun20i_d1.h
> > @@ -0,0 +1,70 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * D1/R528/T113 DRAM controller register and constant defines
> > + *
> > + * (C) Copyright 2022 Arm Ltd.
> > + * Based on H6 and H616 header, which are:
> > + * (C) Copyright 2017 Icenowy Zheng <icenowy at aosc.io>
> > + * (C) Copyright 2020 Jernej Skrabec <jernej.skrabec at siol.net>
> > + *
> > + */
> > +
> > +#ifndef _SUNXI_DRAM_SUN20I_D1_H
> > +#define _SUNXI_DRAM_SUN20I_D1_H
> > +
> > +enum sunxi_dram_type {
> > + SUNXI_DRAM_TYPE_DDR2 = 2,
> > + SUNXI_DRAM_TYPE_DDR3 = 3,
> > + SUNXI_DRAM_TYPE_LPDDR2 = 6,
> > + SUNXI_DRAM_TYPE_LPDDR3 = 7,
> > +};
> > +
> > +/*
> > + * This structure contains a mixture of fixed configuration
> > settings,
> > + * variables that are used at runtime to communicate settings
> > between
> > + * different stages and functions, and unused values.
> > + * This is copied from Allwinner's boot0 data structure, which can
> > be
> > + * found at offset 0x38 in any boot0 binary. To allow matching up
> > some
> > + * board specific settings, this struct is kept compatible, even
> > though
> > + * we don't need all members in our code.
> > + */
> > +typedef struct dram_para {
> > + /* normal configuration */
> > + u32 dram_clk;
> > + u32 dram_type;
> > + u32 dram_zq;
> > + u32 dram_odt_en;
> > +
> > + /* control configuration */
> > + u32 dram_para1;
> > + u32 dram_para2;
> > +
> > + /* timing configuration */
> > + u32 dram_mr0;
> > + u32 dram_mr1;
> > + u32 dram_mr2;
> > + u32 dram_mr3;
> > + u32 dram_tpr0; //DRAMTMG0
> > + u32 dram_tpr1; //DRAMTMG1
> > + u32 dram_tpr2; //DRAMTMG2
> > + u32 dram_tpr3; //DRAMTMG3
> > + u32 dram_tpr4; //DRAMTMG4
> > + u32 dram_tpr5; //DRAMTMG5
> > + u32 dram_tpr6; //DRAMTMG8
> > + u32 dram_tpr7;
> > + u32 dram_tpr8;
> > + u32 dram_tpr9;
> > + u32 dram_tpr10;
> > + u32 dram_tpr11;
> > + u32 dram_tpr12;
> > + u32 dram_tpr13; /* contains a bitfield of DRAM setup
> > settings */
> > +} dram_para_t;
> > +
> > +static inline int ns_to_t(int nanoseconds)
> > +{
> > + const unsigned int ctrl_freq = CONFIG_DRAM_CLK / 2;
> > +
> > + return DIV_ROUND_UP(ctrl_freq * nanoseconds, 1000);
> > +}
> > +
> > +#endif /* _SUNXI_DRAM_SUN20I_D1_H */
>
More information about the U-Boot
mailing list