[PATCH 2/3] sunxi: Switch to PMIC USB power supply VBUS detection

Samuel Holland samuel at sholland.org
Mon Jan 23 00:46:21 CET 2023 

Update boards to use the USB power supply driver, as referenced in the
device tree, instead of a virtual GPIO. This removes the need for some
DM-incompatible special cases in the GPIO driver.

The following five boards used AXP0-VBUS-DETECT in their config, but are
missing the "usb0_vbus_power-supply" property in their device tree:
 - Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
 - Cubieboard4_defconfig / sun9i-a80-cubieboard4
 - Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
 - Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
 - Yones_Toptech_BS1078_V2_defconfig /
   sun6i-a31s-yones-toptech-bs1078-v2

None of those five boards have the MUSB controller (USB OTG) enabled in
their device trees, so this change should not break anything for them.

Additionally, the following board intentionally omits the property
because VBUS is always enabled:
 - Nintendo_NES_Classic_Edition_defconfig /
   sun8i-r16-nintendo-nes-classic

The PHY driver already assumes VBUS is enabled when no detection method
is available, so again this will not cause any problems.

Signed-off-by: Samuel Holland <samuel at sholland.org>
---

 configs/A33-OLinuXino_defconfig                | 2 +-
 configs/Ainol_AW1_defconfig                    | 2 +-
 configs/Cubieboard4_defconfig                  | 3 ++-
 configs/Cubietruck_plus_defconfig              | 2 +-
 configs/MSI_Primo81_defconfig                  | 2 +-
 configs/Merrii_A80_Optimus_defconfig           | 3 ++-
 configs/Nintendo_NES_Classic_Edition_defconfig | 2 +-
 configs/Sinovoip_BPI_M3_defconfig              | 2 +-
 configs/Wexler_TAB7200_defconfig               | 2 +-
 configs/Yones_Toptech_BD1078_defconfig         | 2 +-
 configs/Yones_Toptech_BS1078_V2_defconfig      | 2 +-
 configs/colorfly_e708_q1_defconfig             | 2 +-
 configs/ga10h_v1_1_defconfig                   | 2 +-
 configs/gt90h_v4_defconfig                     | 2 +-
 configs/iNet_D978_rev2_defconfig               | 2 +-
 configs/inet86dz_defconfig                     | 2 +-
 configs/inet_q972_defconfig                    | 2 +-
 configs/polaroid_mid2407pxe03_defconfig        | 2 +-
 configs/polaroid_mid2809pxe04_defconfig        | 2 +-
 configs/q8_a23_tablet_800x480_defconfig        | 2 +-
 configs/q8_a33_tablet_1024x600_defconfig       | 2 +-
 configs/q8_a33_tablet_800x480_defconfig        | 2 +-
 configs/tbs_a711_defconfig                     | 2 +-
 23 files changed, 25 insertions(+), 23 deletions(-)

diff --git a/configs/A33-OLinuXino_defconfig b/configs/A33-OLinuXino_defconfig
index 351a454339..896ddbb95f 100644
--- a/configs/A33-OLinuXino_defconfig
+++ b/configs/A33-OLinuXino_defconfig
@@ -8,7 +8,6 @@ CONFIG_DRAM_ZQ=15291
 CONFIG_DRAM_ODT_EN=y
 CONFIG_MMC0_CD_PIN="PB4"
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PB3"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:3,vmode:0"
@@ -16,5 +15,6 @@ CONFIG_VIDEO_LCD_DCLK_PHASE=0
 CONFIG_VIDEO_LCD_BL_EN="PB2"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DCDC1_VOLT=3300
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/Ainol_AW1_defconfig b/configs/Ainol_AW1_defconfig
index 9a18af8c6e..ec0c216413 100644
--- a/configs/Ainol_AW1_defconfig
+++ b/configs/Ainol_AW1_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=123
 CONFIG_MMC0_CD_PIN="PH1"
 CONFIG_USB0_VBUS_PIN="PB9"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:40000,le:87,ri:112,up:38,lo:141,hs:1,vs:1,sync:3,vmode:0"
 CONFIG_VIDEO_LCD_POWER="PH8"
@@ -18,4 +17,5 @@ CONFIG_SPL_I2C=y
 CONFIG_SYS_I2C_MVTWSI=y
 CONFIG_SYS_I2C_SLAVE=0x7f
 CONFIG_SYS_I2C_SPEED=400000
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/Cubieboard4_defconfig b/configs/Cubieboard4_defconfig
index 04ed79afb6..82a8deac77 100644
--- a/configs/Cubieboard4_defconfig
+++ b/configs/Cubieboard4_defconfig
@@ -7,10 +7,11 @@ CONFIG_DRAM_CLK=672
 CONFIG_MMC0_CD_PIN="PH18"
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH16"
 CONFIG_USB1_VBUS_PIN="PH14"
 CONFIG_USB3_VBUS_PIN="PH15"
 CONFIG_AXP_GPIO=y
 CONFIG_SYS_I2C_SUN8I_RSB=y
+CONFIG_DM_REGULATOR=y
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP809_POWER=y
diff --git a/configs/Cubietruck_plus_defconfig b/configs/Cubietruck_plus_defconfig
index 13f958977b..29f4df2b81 100644
--- a/configs/Cubietruck_plus_defconfig
+++ b/configs/Cubietruck_plus_defconfig
@@ -8,7 +8,6 @@ CONFIG_DRAM_ZQ=15355
 CONFIG_DRAM_ODT_EN=y
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH11"
 CONFIG_USB1_VBUS_PIN="PD29"
 CONFIG_USB2_VBUS_PIN="PL6"
@@ -22,6 +21,7 @@ CONFIG_SYS_I2C_SLAVE=0x7f
 CONFIG_SYS_I2C_SPEED=400000
 CONFIG_PHY_REALTEK=y
 CONFIG_SUN8I_EMAC=y
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO3_VOLT=2500
 CONFIG_AXP_DLDO4_VOLT=3300
 CONFIG_AXP_FLDO1_VOLT=1200
diff --git a/configs/MSI_Primo81_defconfig b/configs/MSI_Primo81_defconfig
index e77b007292..d60eedb482 100644
--- a/configs/MSI_Primo81_defconfig
+++ b/configs/MSI_Primo81_defconfig
@@ -6,13 +6,13 @@ CONFIG_MACH_SUN6I=y
 CONFIG_DRAM_CLK=360
 CONFIG_DRAM_ZQ=122
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:768,y:1024,depth:18,pclk_khz:66000,le:56,ri:60,up:30,lo:36,hs:64,vs:50,sync:3,vmode:0"
 CONFIG_VIDEO_LCD_BL_EN="PA25"
 CONFIG_VIDEO_LCD_BL_PWM="PH13"
 CONFIG_VIDEO_LCD_PANEL_MIPI_4_LANE_513_MBPS_VIA_SSD2828=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 # CONFIG_REQUIRE_SERIAL_CONSOLE is not set
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/Merrii_A80_Optimus_defconfig b/configs/Merrii_A80_Optimus_defconfig
index c5d1f40df3..e772634064 100644
--- a/configs/Merrii_A80_Optimus_defconfig
+++ b/configs/Merrii_A80_Optimus_defconfig
@@ -7,10 +7,11 @@ CONFIG_DRAM_CLK=672
 CONFIG_MMC0_CD_PIN="PH18"
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH3"
 CONFIG_USB1_VBUS_PIN="PH4"
 CONFIG_USB3_VBUS_PIN="PH5"
 CONFIG_AXP_GPIO=y
 CONFIG_SYS_I2C_SUN8I_RSB=y
+CONFIG_DM_REGULATOR=y
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP809_POWER=y
diff --git a/configs/Nintendo_NES_Classic_Edition_defconfig b/configs/Nintendo_NES_Classic_Edition_defconfig
index 18fa3779d4..3046f45012 100644
--- a/configs/Nintendo_NES_Classic_Edition_defconfig
+++ b/configs/Nintendo_NES_Classic_Edition_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A33=y
 CONFIG_DRAM_CLK=600
 CONFIG_DRAM_ZQ=15291
 CONFIG_DRAM_ODT_EN=y
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_AXP_GPIO=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
 # CONFIG_CMD_FLASH is not set
@@ -20,6 +19,7 @@ CONFIG_SYS_NAND_ONFI_DETECTION=y
 CONFIG_SYS_NAND_PAGE_SIZE=0x800
 CONFIG_SYS_NAND_OOBSIZE=0x40
 CONFIG_SYS_NAND_MAX_ECCPOS=1664
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_AXP_ELDO2_VOLT=1800
 CONFIG_CONS_INDEX=5
diff --git a/configs/Sinovoip_BPI_M3_defconfig b/configs/Sinovoip_BPI_M3_defconfig
index 5116fab52d..5642e52ec5 100644
--- a/configs/Sinovoip_BPI_M3_defconfig
+++ b/configs/Sinovoip_BPI_M3_defconfig
@@ -9,7 +9,6 @@ CONFIG_DRAM_ZQ=15355
 CONFIG_DRAM_ODT_EN=y
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH11"
 CONFIG_USB1_VBUS_PIN="PD24"
 CONFIG_AXP_GPIO=y
@@ -19,6 +18,7 @@ CONFIG_CONSOLE_MUX=y
 CONFIG_PHY_REALTEK=y
 CONFIG_SUN8I_EMAC=y
 CONFIG_INITIAL_USB_SCAN_DELAY=500
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DCDC5_VOLT=1200
 CONFIG_AXP_DLDO3_VOLT=3300
 CONFIG_AXP_SW_ON=y
diff --git a/configs/Wexler_TAB7200_defconfig b/configs/Wexler_TAB7200_defconfig
index 101ce57aa4..40aeb6680c 100644
--- a/configs/Wexler_TAB7200_defconfig
+++ b/configs/Wexler_TAB7200_defconfig
@@ -5,7 +5,6 @@ CONFIG_SPL=y
 CONFIG_MACH_SUN7I=y
 CONFIG_DRAM_CLK=384
 CONFIG_USB0_VBUS_PIN="PB9"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH4"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:24,pclk_khz:33000,le:45,ri:210,up:22,lo:22,hs:1,vs:1,sync:3,vmode:0"
@@ -17,6 +16,7 @@ CONFIG_SPL_I2C=y
 CONFIG_SYS_I2C_MVTWSI=y
 CONFIG_SYS_I2C_SLAVE=0x7f
 CONFIG_SYS_I2C_SPEED=400000
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/Yones_Toptech_BD1078_defconfig b/configs/Yones_Toptech_BD1078_defconfig
index f1ceb8b552..f64b29819c 100644
--- a/configs/Yones_Toptech_BD1078_defconfig
+++ b/configs/Yones_Toptech_BD1078_defconfig
@@ -9,7 +9,6 @@ CONFIG_MMC1_CD_PIN="PH2"
 CONFIG_MMC1_PINS_PH=y
 CONFIG_MMC_SUNXI_SLOT_EXTRA=1
 CONFIG_USB0_VBUS_PIN="PB9"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:24,pclk_khz:63000,le:32,ri:287,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
 CONFIG_VIDEO_LCD_DCLK_PHASE=0
@@ -23,4 +22,5 @@ CONFIG_SPL_I2C=y
 CONFIG_SYS_I2C_MVTWSI=y
 CONFIG_SYS_I2C_SLAVE=0x7f
 CONFIG_SYS_I2C_SPEED=400000
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/Yones_Toptech_BS1078_V2_defconfig b/configs/Yones_Toptech_BS1078_V2_defconfig
index 6701ecce2f..e54dbeddf5 100644
--- a/configs/Yones_Toptech_BS1078_V2_defconfig
+++ b/configs/Yones_Toptech_BS1078_V2_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=420
 CONFIG_DRAM_ZQ=251
 CONFIG_MMC0_CD_PIN="PA8"
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PA15"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:24,pclk_khz:70000,le:120,ri:180,up:17,lo:15,hs:20,vs:3,sync:3,vmode:0"
@@ -16,5 +15,6 @@ CONFIG_VIDEO_LCD_BL_EN="PA25"
 CONFIG_VIDEO_LCD_BL_PWM="PH13"
 CONFIG_VIDEO_LCD_PANEL_LVDS=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/colorfly_e708_q1_defconfig b/configs/colorfly_e708_q1_defconfig
index 5d3636e34e..5a77ec11e8 100644
--- a/configs/colorfly_e708_q1_defconfig
+++ b/configs/colorfly_e708_q1_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=251
 CONFIG_MMC0_CD_PIN="PA8"
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PA15"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:1280,depth:24,pclk_khz:64000,le:20,ri:34,up:1,lo:16,hs:10,vs:1,sync:3,vmode:0"
@@ -16,6 +15,7 @@ CONFIG_VIDEO_LCD_BL_EN="PA25"
 CONFIG_VIDEO_LCD_BL_PWM="PH13"
 CONFIG_VIDEO_LCD_PANEL_LVDS=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_AXP_DLDO2_VOLT=1800
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/ga10h_v1_1_defconfig b/configs/ga10h_v1_1_defconfig
index 599eeb96b4..935071d61a 100644
--- a/configs/ga10h_v1_1_defconfig
+++ b/configs/ga10h_v1_1_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=15291
 CONFIG_DRAM_ODT_EN=y
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:52000,le:138,ri:162,up:22,lo:10,hs:20,vs:3,sync:3,vmode:0"
@@ -17,6 +16,7 @@ CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 CONFIG_VIDEO_LCD_PANEL_LVDS=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_EHCI_HCD=y
diff --git a/configs/gt90h_v4_defconfig b/configs/gt90h_v4_defconfig
index 1a5fe06bbe..85185930db 100644
--- a/configs/gt90h_v4_defconfig
+++ b/configs/gt90h_v4_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=480
 CONFIG_DRAM_ZQ=32767
 CONFIG_MMC0_CD_PIN="PB4"
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:55000,le:159,ri:160,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
@@ -16,6 +15,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/iNet_D978_rev2_defconfig b/configs/iNet_D978_rev2_defconfig
index 9a90252dbd..f9d0f88e67 100644
--- a/configs/iNet_D978_rev2_defconfig
+++ b/configs/iNet_D978_rev2_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=456
 CONFIG_DRAM_ZQ=15291
 CONFIG_MMC0_CD_PIN="PB4"
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:768,depth:18,pclk_khz:65000,le:120,ri:180,up:22,lo:13,hs:20,vs:3,sync:3,vmode:0"
@@ -17,6 +16,7 @@ CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 CONFIG_VIDEO_LCD_PANEL_LVDS=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 # CONFIG_REQUIRE_SERIAL_CONSOLE is not set
 CONFIG_CONS_INDEX=5
diff --git a/configs/inet86dz_defconfig b/configs/inet86dz_defconfig
index 3ade9fea82..7f8651d898 100644
--- a/configs/inet86dz_defconfig
+++ b/configs/inet86dz_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=552
 CONFIG_DRAM_ZQ=63351
 CONFIG_MMC0_CD_PIN="PB4"
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:51000,le:138,ri:162,up:22,lo:10,hs:20,vs:3,sync:3,vmode:0"
@@ -16,6 +15,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/inet_q972_defconfig b/configs/inet_q972_defconfig
index 1769256b7d..408c9ccac9 100644
--- a/configs/inet_q972_defconfig
+++ b/configs/inet_q972_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=384
 CONFIG_DRAM_ZQ=251
 CONFIG_MMC0_CD_PIN="PA8"
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PA15"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:768,depth:18,pclk_khz:65000,le:280,ri:20,up:22,lo:8,hs:20,vs:8,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_DCLK_PHASE=0
 CONFIG_VIDEO_LCD_BL_EN="PA25"
 CONFIG_VIDEO_LCD_BL_PWM="PH13"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y
diff --git a/configs/polaroid_mid2407pxe03_defconfig b/configs/polaroid_mid2407pxe03_defconfig
index 17fffeb1e2..d11d72ba99 100644
--- a/configs/polaroid_mid2407pxe03_defconfig
+++ b/configs/polaroid_mid2407pxe03_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=63351
 CONFIG_MMC0_CD_PIN="PB4"
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:40,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
@@ -16,6 +15,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/polaroid_mid2809pxe04_defconfig b/configs/polaroid_mid2809pxe04_defconfig
index e542b71113..68e2392643 100644
--- a/configs/polaroid_mid2809pxe04_defconfig
+++ b/configs/polaroid_mid2809pxe04_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=63351
 CONFIG_MMC0_CD_PIN="PB4"
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:36,ri:210,up:18,lo:22,hs:10,vs:5,sync:3,vmode:0"
@@ -16,6 +15,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/q8_a23_tablet_800x480_defconfig b/configs/q8_a23_tablet_800x480_defconfig
index dda1a0c51f..dcf23e90d2 100644
--- a/configs/q8_a23_tablet_800x480_defconfig
+++ b/configs/q8_a23_tablet_800x480_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=63306
 CONFIG_MMC0_CD_PIN="PB4"
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:36,ri:210,up:18,lo:22,hs:10,vs:5,sync:3,vmode:0"
@@ -16,6 +15,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/q8_a33_tablet_1024x600_defconfig b/configs/q8_a33_tablet_1024x600_defconfig
index 7925677d30..74635985a0 100644
--- a/configs/q8_a33_tablet_1024x600_defconfig
+++ b/configs/q8_a33_tablet_1024x600_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=456
 CONFIG_DRAM_ZQ=15291
 CONFIG_MMC0_CD_PIN="PB4"
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:51000,le:159,ri:160,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
@@ -16,6 +15,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/q8_a33_tablet_800x480_defconfig b/configs/q8_a33_tablet_800x480_defconfig
index f3335f9d23..770acc840d 100644
--- a/configs/q8_a33_tablet_800x480_defconfig
+++ b/configs/q8_a33_tablet_800x480_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=456
 CONFIG_DRAM_ZQ=15291
 CONFIG_MMC0_CD_PIN="PB4"
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:167,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
@@ -16,6 +15,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/tbs_a711_defconfig b/configs/tbs_a711_defconfig
index b3c2e69d6c..9a70b6bee5 100644
--- a/configs/tbs_a711_defconfig
+++ b/configs/tbs_a711_defconfig
@@ -9,11 +9,11 @@ CONFIG_DRAM_ZQ=15355
 CONFIG_DRAM_ODT_EN=y
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH11"
 CONFIG_AXP_GPIO=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
 CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DCDC5_VOLT=1200
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y
-- 
2.37.4

More information about the U-Boot mailing list