[PATCH v2 2/3] power: regulator: Add a driver for AXP PMIC regulators
Simon Glass
sjg at chromium.org
Mon Jan 23 19:49:53 CET 2023
Hi Samuel,
On Sat, 21 Jan 2023 at 17:28, Samuel Holland <samuel at sholland.org> wrote:
>
> This driver handles most voltage regulators found in X-Powers AXP PMICs.
> It is based on, and intended to replace, the regulator driver in TF-A.
>
> AXP PMIC regulators can be divided into 6 categories:
> - Switches without voltage control => fully supported.
> - Single linear range => fully supported.
> - Two linear ranges, "step" and "2 * step" => fully supported.
> - Two linear ranges, "step" and "5 * step" => only the first range is
> supported. No boards are known to use the second range.
> - Non-linear voltage values => fully supported.
> - LDOs shared with GPIO pins => not supported.
>
> Signed-off-by: Samuel Holland <samuel at sholland.org>
> ---
>
> Changes in v2:
> - Dual-license the driver
> - Add a comment about the requirements for the voltage table
> - Fix AXP22x ALDO3 enable bit position
>
> drivers/power/regulator/Kconfig | 14 ++
> drivers/power/regulator/Makefile | 1 +
> drivers/power/regulator/axp_regulator.c | 312 ++++++++++++++++++++++++
> 3 files changed, 327 insertions(+)
> create mode 100644 drivers/power/regulator/axp_regulator.c
>
> diff --git a/drivers/power/regulator/Kconfig b/drivers/power/regulator/Kconfig
> index c02e6377d8..c346d03507 100644
> --- a/drivers/power/regulator/Kconfig
> +++ b/drivers/power/regulator/Kconfig
> @@ -43,6 +43,20 @@ config REGULATOR_AS3722
> but does not yet support change voltages. Currently this must be
> done using direct register writes to the PMIC.
>
> +config REGULATOR_AXP
> + bool "Enable driver for X-Powers AXP PMIC regulators"
> + depends on DM_REGULATOR && PMIC_AXP
> + help
> + Enable support for the regulators (DCDCs, LDOs) in the
> + X-Powers AXP152, AXP2xx, and AXP8xx PMICs.
> +
> +config SPL_REGULATOR_AXP
> + bool "Enable driver for X-Powers AXP PMIC regulators in SPL"
> + depends on SPL_DM_REGULATOR && SPL_PMIC_AXP
> + help
> + Enable support in SPL for the regulators (DCDCs, LDOs) in the
> + X-Powers AXP152, AXP2xx, and AXP8xx PMICs.
> +
> config DM_REGULATOR_BD71837
> bool "Enable Driver Model for ROHM BD71837/BD71847 regulators"
> depends on DM_REGULATOR && DM_PMIC_BD71837
> diff --git a/drivers/power/regulator/Makefile b/drivers/power/regulator/Makefile
> index 68e4c0f9dd..2d97e1033a 100644
> --- a/drivers/power/regulator/Makefile
> +++ b/drivers/power/regulator/Makefile
> @@ -7,6 +7,7 @@
> obj-$(CONFIG_$(SPL_)DM_REGULATOR) += regulator-uclass.o
> obj-$(CONFIG_REGULATOR_ACT8846) += act8846.o
> obj-$(CONFIG_REGULATOR_AS3722) += as3722_regulator.o
> +obj-$(CONFIG_$(SPL_)REGULATOR_AXP) += axp_regulator.o
> obj-$(CONFIG_$(SPL_)DM_REGULATOR_DA9063) += da9063.o
> obj-$(CONFIG_DM_REGULATOR_MAX77686) += max77686.o
> obj-$(CONFIG_DM_REGULATOR_NPCM8XX) += npcm8xx_regulator.o
> diff --git a/drivers/power/regulator/axp_regulator.c b/drivers/power/regulator/axp_regulator.c
> new file mode 100644
> index 0000000000..02f320eac1
> --- /dev/null
> +++ b/drivers/power/regulator/axp_regulator.c
> @@ -0,0 +1,312 @@
> +// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
> +/*
> + * Copyright (c) 2017-2019, ARM Limited and Contributors. All rights reserved.
> + * Copyright (c) 2018-2023 Samuel Holland <samuel at sholland.org>
> + */
> +
> +#include <axp_pmic.h>
> +#include <dm.h>
> +#include <errno.h>
> +#include <dm/device-internal.h>
> +#include <power/pmic.h>
> +#include <power/regulator.h>
> +
> +#define NA 0xff
> +
> +struct axp_regulator_plat {
> + const char *name;
> + u8 enable_reg;
> + u8 enable_mask;
> + u8 volt_reg;
> + u8 volt_mask;
> + u16 min_mV;
> + u16 max_mV;
> + u8 step_mV;
> + u8 split;
> + const u16 *table;
> +};
Please comment struct
> +
> +static int axp_regulator_get_value(struct udevice *dev)
> +{
> + const struct axp_regulator_plat *plat = dev_get_plat(dev);
> + int mV, sel;
> +
> + if (plat->volt_reg == NA)
> + return -EINVAL;
> +
> + sel = pmic_reg_read(dev->parent, plat->volt_reg);
> + if (sel < 0)
> + return sel;
> +
> + sel &= plat->volt_mask;
> + sel >>= ffs(plat->volt_mask) - 1;
> +
> + if (plat->table) {
> + mV = plat->table[sel];
> + } else {
> + if (sel > plat->split)
> + sel = plat->split + (sel - plat->split) * 2;
> + mV = plat->min_mV + sel * plat->step_mV;
> + }
> +
> + return mV * 1000;
> +}
> +
> +static int axp_regulator_set_value(struct udevice *dev, int uV)
> +{
> + const struct axp_regulator_plat *plat = dev_get_plat(dev);
> + int mV = uV / 1000;
> + uint sel, shift;
> +
> + if (plat->volt_reg == NA)
> + return -EINVAL;
> + if (mV < plat->min_mV || mV > plat->max_mV)
> + return -EINVAL;
> +
> + shift = ffs(plat->volt_mask) - 1;
> +
> + if (plat->table) {
> + /*
> + * The table must be monotonically increasing and
> + * have an entry for each possible field value.
> + */
> + sel = plat->volt_mask >> shift;
> + while (sel && plat->table[sel] > mV)
> + sel--;
> + } else {
> + sel = (mV - plat->min_mV) / plat->step_mV;
> + if (sel > plat->split)
> + sel = plat->split + (sel - plat->split) / 2;
> + }
> +
> + return pmic_clrsetbits(dev->parent, plat->volt_reg,
> + plat->volt_mask, sel << shift);
> +}
> +
> +static int axp_regulator_get_enable(struct udevice *dev)
> +{
> + const struct axp_regulator_plat *plat = dev_get_plat(dev);
> + int reg;
> +
> + reg = pmic_reg_read(dev->parent, plat->enable_reg);
> + if (reg < 0)
> + return reg;
> +
> + return (reg & plat->enable_mask) == plat->enable_mask;
> +}
> +
> +static int axp_regulator_set_enable(struct udevice *dev, bool enable)
> +{
> + const struct axp_regulator_plat *plat = dev_get_plat(dev);
> +
> + return pmic_clrsetbits(dev->parent, plat->enable_reg,
> + plat->enable_mask,
> + enable ? plat->enable_mask : 0);
> +}
> +
> +static const struct dm_regulator_ops axp_regulator_ops = {
> + .get_value = axp_regulator_get_value,
> + .set_value = axp_regulator_set_value,
> + .get_enable = axp_regulator_get_enable,
> + .set_enable = axp_regulator_set_enable,
> +};
> +
> +static const u16 axp152_dcdc1_table[] = {
> + 1700, 1800, 1900, 2000, 2100, 2400, 2500, 2600,
> + 2700, 2800, 3000, 3100, 3200, 3300, 3400, 3500,
> +};
> +
> +static const u16 axp152_aldo12_table[] = {
> + 1200, 1300, 1400, 1500, 1600, 1700, 1800, 1900,
> + 2000, 2500, 2700, 2800, 3000, 3100, 3200, 3300,
> +};
> +
> +static const u16 axp152_ldo0_table[] = {
> + 5000, 3300, 2800, 2500,
> +};
> +
> +static const struct axp_regulator_plat axp152_regulators[] = {
> + { "dcdc1", 0x12, BIT(7), 0x26, 0x0f, .table = axp152_dcdc1_table },
> + { "dcdc2", 0x12, BIT(6), 0x23, 0x3f, 700, 2275, 25, NA },
> + { "dcdc3", 0x12, BIT(5), 0x27, 0x3f, 700, 3500, 50, NA },
> + { "dcdc4", 0x12, BIT(4), 0x2b, 0x7f, 700, 3500, 25, NA },
> + { "aldo1", 0x12, BIT(3), 0x28, 0xf0, .table = axp152_aldo12_table },
> + { "aldo2", 0x12, BIT(2), 0x28, 0x0f, .table = axp152_aldo12_table },
> + { "dldo1", 0x12, BIT(1), 0x29, 0x1f, 700, 3500, 100, NA },
> + { "dldo2", 0x12, BIT(0), 0x2a, 0x1f, 700, 3500, 100, NA },
> + { "ldo0", 0x15, BIT(7), 0x15, 0x30, .table = axp152_ldo0_table },
> + { }
> +};
> +
> +static const u16 axp20x_ldo4_table[] = {
> + 1250, 1300, 1400, 1500, 1600, 1700, 1800, 1900,
> + 2000, 2500, 2700, 2800, 3000, 3100, 3200, 3300,
> +};
> +
> +static const struct axp_regulator_plat axp20x_regulators[] = {
> + { "dcdc2", 0x12, BIT(4), 0x23, 0x3f, 700, 2275, 25, NA },
> + { "dcdc3", 0x12, BIT(1), 0x27, 0x7f, 700, 3500, 25, NA },
> + { "ldo2", 0x12, BIT(2), 0x28, 0xf0, 1800, 3300, 100, NA },
> + { "ldo3", 0x12, BIT(6), 0x29, 0x7f, 700, 2275, 25, NA },
> + { "ldo4", 0x12, BIT(3), 0x28, 0x0f, .table = axp20x_ldo4_table },
> + { }
> +};
> +
> +static const struct axp_regulator_plat axp22x_regulators[] = {
> + {"dc5ldo", 0x10, BIT(0), 0x1c, 0x07, 700, 1400, 100, NA },
> + { "dcdc1", 0x10, BIT(1), 0x21, 0x1f, 1600, 3400, 100, NA },
> + { "dcdc2", 0x10, BIT(2), 0x22, 0x3f, 600, 1540, 20, NA },
> + { "dcdc3", 0x10, BIT(3), 0x23, 0x3f, 600, 1860, 20, NA },
> + { "dcdc4", 0x10, BIT(4), 0x24, 0x3f, 600, 1540, 20, NA },
> + { "dcdc5", 0x10, BIT(5), 0x25, 0x1f, 1000, 2550, 50, NA },
> + { "aldo1", 0x10, BIT(6), 0x28, 0x1f, 700, 3300, 100, NA },
> + { "aldo2", 0x10, BIT(7), 0x29, 0x1f, 700, 3300, 100, NA },
> + { "aldo3", 0x13, BIT(7), 0x2a, 0x1f, 700, 3300, 100, NA },
> + { "dldo1", 0x12, BIT(3), 0x15, 0x1f, 700, 3300, 100, NA },
> + { "dldo2", 0x12, BIT(4), 0x16, 0x1f, 700, 3300, 100, NA },
> + { "dldo3", 0x12, BIT(5), 0x17, 0x1f, 700, 3300, 100, NA },
> + { "dldo4", 0x12, BIT(6), 0x18, 0x1f, 700, 3300, 100, NA },
> + { "eldo1", 0x12, BIT(0), 0x19, 0x1f, 700, 3300, 100, NA },
> + { "eldo2", 0x12, BIT(1), 0x1a, 0x1f, 700, 3300, 100, NA },
> + { "eldo3", 0x12, BIT(2), 0x1b, 0x1f, 700, 3300, 100, NA },
> + { "dc1sw", 0x12, BIT(7), NA, NA, NA, NA, NA, NA },
> + { }
> +};
> +
> +static const struct axp_regulator_plat axp803_regulators[] = {
> + { "dcdc1", 0x10, BIT(0), 0x20, 0x1f, 1600, 3400, 100, NA },
> + { "dcdc2", 0x10, BIT(1), 0x21, 0x7f, 500, 1300, 10, 70 },
> + { "dcdc3", 0x10, BIT(2), 0x22, 0x7f, 500, 1300, 10, 70 },
> + { "dcdc4", 0x10, BIT(3), 0x23, 0x7f, 500, 1300, 10, 70 },
> + { "dcdc5", 0x10, BIT(4), 0x24, 0x7f, 800, 1840, 10, 32 },
> + { "dcdc6", 0x10, BIT(5), 0x25, 0x7f, 600, 1520, 10, 50 },
> + { "aldo1", 0x13, BIT(5), 0x28, 0x1f, 700, 3300, 100, NA },
> + { "aldo2", 0x13, BIT(6), 0x29, 0x1f, 700, 3300, 100, NA },
> + { "aldo3", 0x13, BIT(7), 0x2a, 0x1f, 700, 3300, 100, NA },
> + { "dldo1", 0x12, BIT(3), 0x15, 0x1f, 700, 3300, 100, NA },
> + { "dldo2", 0x12, BIT(4), 0x16, 0x1f, 700, 4200, 100, 27 },
> + { "dldo3", 0x12, BIT(5), 0x17, 0x1f, 700, 3300, 100, NA },
> + { "dldo4", 0x12, BIT(6), 0x18, 0x1f, 700, 3300, 100, NA },
> + { "eldo1", 0x12, BIT(0), 0x19, 0x1f, 700, 1900, 50, NA },
> + { "eldo2", 0x12, BIT(1), 0x1a, 0x1f, 700, 1900, 50, NA },
> + { "eldo3", 0x12, BIT(2), 0x1b, 0x1f, 700, 1900, 50, NA },
> + { "fldo1", 0x13, BIT(2), 0x1c, 0x0f, 700, 1450, 50, NA },
> + { "fldo2", 0x13, BIT(3), 0x1d, 0x0f, 700, 1450, 50, NA },
> + { "dc1sw", 0x12, BIT(7), NA, NA, NA, NA, NA, NA },
> + { }
> +};
> +
> +/*
> + * The "dcdcd" split changes the step size by a factor of 5, not 2;
> + * disallow values above the split to maintain accuracy.
> + */
> +static const struct axp_regulator_plat axp806_regulators[] = {
> + { "dcdca", 0x10, BIT(0), 0x12, 0x7f, 600, 1520, 10, 50 },
> + { "dcdcb", 0x10, BIT(1), 0x13, 0x1f, 1000, 2550, 50, NA },
> + { "dcdcc", 0x10, BIT(2), 0x14, 0x7f, 600, 1520, 10, 50 },
> + { "dcdcd", 0x10, BIT(3), 0x15, 0x3f, 600, 1500, 20, NA },
> + { "dcdce", 0x10, BIT(4), 0x16, 0x1f, 1100, 3400, 100, NA },
> + { "aldo1", 0x10, BIT(5), 0x17, 0x1f, 700, 3300, 100, NA },
> + { "aldo2", 0x10, BIT(6), 0x18, 0x1f, 700, 3300, 100, NA },
> + { "aldo3", 0x10, BIT(7), 0x19, 0x1f, 700, 3300, 100, NA },
> + { "bldo1", 0x11, BIT(0), 0x20, 0x0f, 700, 1900, 100, NA },
> + { "bldo2", 0x11, BIT(1), 0x21, 0x0f, 700, 1900, 100, NA },
> + { "bldo3", 0x11, BIT(2), 0x22, 0x0f, 700, 1900, 100, NA },
> + { "bldo4", 0x11, BIT(3), 0x23, 0x0f, 700, 1900, 100, NA },
> + { "cldo1", 0x11, BIT(4), 0x24, 0x1f, 700, 3300, 100, NA },
> + { "cldo2", 0x11, BIT(5), 0x25, 0x1f, 700, 4200, 100, 27 },
> + { "cldo3", 0x11, BIT(6), 0x26, 0x1f, 700, 3300, 100, NA },
> + { "sw", 0x11, BIT(7), NA, NA, NA, NA, NA, NA },
> + { }
> +};
> +
> +/*
> + * The "dcdc4" split changes the step size by a factor of 5, not 2;
> + * disallow values above the split to maintain accuracy.
> + */
> +static const struct axp_regulator_plat axp809_regulators[] = {
> + {"dc5ldo", 0x10, BIT(0), 0x1c, 0x07, 700, 1400, 100, NA },
> + { "dcdc1", 0x10, BIT(1), 0x21, 0x1f, 1600, 3400, 100, NA },
> + { "dcdc2", 0x10, BIT(2), 0x22, 0x3f, 600, 1540, 20, NA },
> + { "dcdc3", 0x10, BIT(3), 0x23, 0x3f, 600, 1860, 20, NA },
> + { "dcdc4", 0x10, BIT(4), 0x24, 0x3f, 600, 1540, 20, NA },
> + { "dcdc5", 0x10, BIT(5), 0x25, 0x1f, 1000, 2550, 50, NA },
> + { "aldo1", 0x10, BIT(6), 0x28, 0x1f, 700, 3300, 100, NA },
> + { "aldo2", 0x10, BIT(7), 0x29, 0x1f, 700, 3300, 100, NA },
> + { "aldo3", 0x12, BIT(5), 0x2a, 0x1f, 700, 3300, 100, NA },
> + { "dldo1", 0x12, BIT(3), 0x15, 0x1f, 700, 3300, 100, NA },
> + { "dldo2", 0x12, BIT(4), 0x16, 0x1f, 700, 3300, 100, NA },
> + { "eldo1", 0x12, BIT(0), 0x19, 0x1f, 700, 3300, 100, NA },
> + { "eldo2", 0x12, BIT(1), 0x1a, 0x1f, 700, 3300, 100, NA },
> + { "eldo3", 0x12, BIT(2), 0x1b, 0x1f, 700, 3300, 100, NA },
> + { "sw", 0x12, BIT(6), NA, NA, NA, NA, NA, NA },
> + { "dc1sw", 0x12, BIT(7), NA, NA, NA, NA, NA, NA },
> + { }
> +};
> +
> +static const struct axp_regulator_plat axp813_regulators[] = {
> + { "dcdc1", 0x10, BIT(0), 0x20, 0x1f, 1600, 3400, 100, NA },
> + { "dcdc2", 0x10, BIT(1), 0x21, 0x7f, 500, 1300, 10, 70 },
> + { "dcdc3", 0x10, BIT(2), 0x22, 0x7f, 500, 1300, 10, 70 },
> + { "dcdc4", 0x10, BIT(3), 0x23, 0x7f, 500, 1300, 10, 70 },
> + { "dcdc5", 0x10, BIT(4), 0x24, 0x7f, 800, 1840, 10, 32 },
> + { "dcdc6", 0x10, BIT(5), 0x25, 0x7f, 600, 1520, 10, 50 },
> + { "dcdc7", 0x10, BIT(6), 0x26, 0x7f, 600, 1520, 10, 50 },
> + { "aldo1", 0x13, BIT(5), 0x28, 0x1f, 700, 3300, 100, NA },
> + { "aldo2", 0x13, BIT(6), 0x29, 0x1f, 700, 3300, 100, NA },
> + { "aldo3", 0x13, BIT(7), 0x2a, 0x1f, 700, 3300, 100, NA },
> + { "dldo1", 0x12, BIT(3), 0x15, 0x1f, 700, 3300, 100, NA },
> + { "dldo2", 0x12, BIT(4), 0x16, 0x1f, 700, 4200, 100, 27 },
> + { "dldo3", 0x12, BIT(5), 0x17, 0x1f, 700, 3300, 100, NA },
> + { "dldo4", 0x12, BIT(6), 0x18, 0x1f, 700, 3300, 100, NA },
> + { "eldo1", 0x12, BIT(0), 0x19, 0x1f, 700, 1900, 50, NA },
> + { "eldo2", 0x12, BIT(1), 0x1a, 0x1f, 700, 1900, 50, NA },
> + { "eldo3", 0x12, BIT(2), 0x1b, 0x1f, 700, 1900, 50, NA },
> + { "fldo1", 0x13, BIT(2), 0x1c, 0x0f, 700, 1450, 50, NA },
> + { "fldo2", 0x13, BIT(3), 0x1d, 0x0f, 700, 1450, 50, NA },
> + { "fldo3", 0x13, BIT(4), NA, NA, NA, NA, NA, NA },
> + { }
> +};
> +
> +static const struct axp_regulator_plat *const axp_regulators[] = {
> + [AXP152_ID] = axp152_regulators,
> + [AXP202_ID] = axp20x_regulators,
> + [AXP209_ID] = axp20x_regulators,
> + [AXP221_ID] = axp22x_regulators,
> + [AXP223_ID] = axp22x_regulators,
> + [AXP803_ID] = axp803_regulators,
> + [AXP806_ID] = axp806_regulators,
> + [AXP809_ID] = axp809_regulators,
> + [AXP813_ID] = axp813_regulators,
> +};
> +
> +static int axp_regulator_bind(struct udevice *dev)
> +{
> + struct dm_regulator_uclass_plat *uc_plat = dev_get_uclass_plat(dev);
> + ulong id = dev_get_driver_data(dev->parent);
> + const struct axp_regulator_plat *plat;
> +
> + for (plat = axp_regulators[id]; plat && plat->name; plat++)
> + if (!strcmp(plat->name, dev->name))
> + break;
> + if (!plat || !plat->name)
> + return -ENODEV;
> +
> + dev_set_plat(dev, (void *)plat);
Wow this is really wacky.
Where is the compatible string?
> +
> + if (plat->volt_reg == NA)
> + uc_plat->type = REGULATOR_TYPE_FIXED;
> + else if (!strncmp(plat->name, "dcdc", strlen("dcdc")))
> + uc_plat->type = REGULATOR_TYPE_BUCK;
> + else
> + uc_plat->type = REGULATOR_TYPE_LDO;
> +
> + return 0;
> +}
> +
> +U_BOOT_DRIVER(axp_regulator) = {
> + .name = "axp_regulator",
> + .id = UCLASS_REGULATOR,
> + .bind = axp_regulator_bind,
> + .ops = &axp_regulator_ops,
> +};
> --
> 2.37.4
>
Regards,
Simon
More information about the U-Boot
mailing list