[PATCH 5/5] gpio/rockchip: rk_gpio support v2 gpio controller
Johan Jonker
jbx6244 at gmail.com
Thu Jan 26 19:11:15 CET 2023
On 1/26/23 17:11, Chris Morgan wrote:
> On Thu, Jan 19, 2023 at 12:21:02PM -0600, Chris Morgan wrote:
>> On Thu, Jan 05, 2023 at 07:01:40PM +0100, Quentin Schulz wrote:
>>> Hi Chris,
>>>
>>> Cc'ing the new mail address of Heiko so he receives this mail :)
>>>
>>> On 1/5/23 16:34, Chris Morgan wrote:
>>>> From: Chris Morgan <macromorgan at hotmail.com>
>>>>
>>>> Add support for the newer GPIO controller used by the rk356x series,
>>>> as well as the pinctrl device for the rk356x series. The GPIOv2
>>>> controller has a write enable bit for some registers which differs
>>>> from the older versions of the GPIO controller.
>>>>
>>>> Adapted from Peter Geis's gitlab located here:
>>>> https://urldefense.com/v3/__https://gitlab.com/pgwipeout/u-boot-quartz64/-/commit/1a84cc483d0979fa00c6f7d6c76d870c25ab3cbd__;!!OOPJP91ZZw!i7xaxb0VOR6CU_lauUnYs4-WlEgdGZCaETaNwp--V4jwJoQguyPr07GTOXDhDNNYL4vYLzae_eObZKZUYUAm4pVFA6vGK-JnXjIz$
>>>>
>>>> Signed-off-by: Chris Morgan <macromorgan at hotmail.com>
>>>> ---
>>>> arch/arm/include/asm/arch-rockchip/gpio.h | 38 ++
>>>> drivers/gpio/Kconfig | 13 +
>>>> drivers/gpio/rk_gpio.c | 103 +++-
>>>> drivers/pinctrl/rockchip/Makefile | 1 +
>>>> drivers/pinctrl/rockchip/pinctrl-rk3568.c | 453 ++++++++++++++++++
>>>> .../pinctrl/rockchip/pinctrl-rockchip-core.c | 12 +-
>>>> drivers/pinctrl/rockchip/pinctrl-rockchip.h | 42 ++
>>>> 7 files changed, 635 insertions(+), 27 deletions(-)
>>>> create mode 100644 drivers/pinctrl/rockchip/pinctrl-rk3568.c
>>>>
>>>> diff --git a/arch/arm/include/asm/arch-rockchip/gpio.h b/arch/arm/include/asm/arch-rockchip/gpio.h
>>>> index 1aaec5faec..29120ceaf3 100644
>>>> --- a/arch/arm/include/asm/arch-rockchip/gpio.h
>>>> +++ b/arch/arm/include/asm/arch-rockchip/gpio.h
>>>> @@ -6,6 +6,7 @@
>>>> #ifndef _ASM_ARCH_GPIO_H
>>>> #define _ASM_ARCH_GPIO_H
>>>> +#ifndef CONFIG_ROCKCHIP_GPIO_V2
>>>> struct rockchip_gpio_regs {
>>>> u32 swport_dr;
>>>> u32 swport_ddr;
>>>> @@ -22,7 +23,44 @@ struct rockchip_gpio_regs {
>>>> u32 reserved1[(0x60 - 0x54) / 4];
>>>> u32 ls_sync;
>>>> };
>>>> +
>>>> check_member(rockchip_gpio_regs, ls_sync, 0x60);
>>>> +#else
>>>> +struct rockchip_gpio_regs {
>>>> + u32 swport_dr_l; /* ADDRESS OFFSET: 0x0000 */
>>>> + u32 swport_dr_h; /* ADDRESS OFFSET: 0x0004 */
>>>> + u32 swport_ddr_l; /* ADDRESS OFFSET: 0x0008 */
>>>> + u32 swport_ddr_h; /* ADDRESS OFFSET: 0x000c */
>>>> + u32 int_en_l; /* ADDRESS OFFSET: 0x0010 */
>>>> + u32 int_en_h; /* ADDRESS OFFSET: 0x0014 */
>>>> + u32 int_mask_l; /* ADDRESS OFFSET: 0x0018 */
>>>> + u32 int_mask_h; /* ADDRESS OFFSET: 0x001c */
>>>> + u32 int_type_l; /* ADDRESS OFFSET: 0x0020 */
>>>> + u32 int_type_h; /* ADDRESS OFFSET: 0x0024 */
>>>> + u32 int_polarity_l; /* ADDRESS OFFSET: 0x0028 */
>>>> + u32 int_polarity_h; /* ADDRESS OFFSET: 0x002c */
>>>> + u32 int_bothedge_l; /* ADDRESS OFFSET: 0x0030 */
>>>> + u32 int_bothedge_h; /* ADDRESS OFFSET: 0x0034 */
>>>> + u32 debounce_l; /* ADDRESS OFFSET: 0x0038 */
>>>> + u32 debounce_h; /* ADDRESS OFFSET: 0x003c */
>>>> + u32 dbclk_div_en_l; /* ADDRESS OFFSET: 0x0040 */
>>>> + u32 dbclk_div_en_h; /* ADDRESS OFFSET: 0x0044 */
>>>> + u32 dbclk_div_con; /* ADDRESS OFFSET: 0x0048 */
>>>> + u32 reserved004c; /* ADDRESS OFFSET: 0x004c */
>>>> + u32 int_status; /* ADDRESS OFFSET: 0x0050 */
>>>> + u32 reserved0054; /* ADDRESS OFFSET: 0x0054 */
>>>> + u32 int_rawstatus; /* ADDRESS OFFSET: 0x0058 */
>>>> + u32 reserved005c; /* ADDRESS OFFSET: 0x005c */
>>>> + u32 port_eoi_l; /* ADDRESS OFFSET: 0x0060 */
>>>> + u32 port_eoi_h; /* ADDRESS OFFSET: 0x0064 */
>>>> + u32 reserved0068[2]; /* ADDRESS OFFSET: 0x0068 */
>>>> + u32 ext_port; /* ADDRESS OFFSET: 0x0070 */
>>>> + u32 reserved0074; /* ADDRESS OFFSET: 0x0074 */
>>>> + u32 ver_id; /* ADDRESS OFFSET: 0x0078 */
>>>> +};
>>>> +
>>>> +check_member(rockchip_gpio_regs, ver_id, 0x0078);
>>>> +#endif
>>>> enum gpio_pu_pd {
>>>> GPIO_PULL_NORMAL = 0,
>>>> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
>>>> index ff87fbfb39..bd7422a0b3 100644
>>>> --- a/drivers/gpio/Kconfig
>>>> +++ b/drivers/gpio/Kconfig
>>>> @@ -340,6 +340,19 @@ config ROCKCHIP_GPIO
>>>> The GPIOs for a device are defined in the device tree with one node
>>>> for each bank.
>>>> +config ROCKCHIP_GPIO_V2
>>>> + bool "Rockchip GPIO driver version 2.0"
>>>> + depends on ROCKCHIP_GPIO
>>>
>>> I would make ROCKCHIP_GPIO and ROCKCHIP_GPIO_V2 incompatible with each
>>> other, otherwise ROCKCHIP_GPIO represents both the GPIO controller and the
>>> v1, but not v1 if v2 is selected. That's a bit confusing to me.
>>>
>>> [...]
In Linux they think it is better to use one common fall back string .
compatible = "rockchip,rk3568-gpio-bank", "rockchip,gpio-bank";
>>>> @@ -142,19 +171,49 @@ static int rockchip_gpio_probe(struct udevice *dev)
>>>> {
>>>> struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
>>>> struct rockchip_gpio_priv *priv = dev_get_priv(dev);
>>>> - char *end;
>>>> - int ret;
>>>> + struct rockchip_pinctrl_priv *pctrl_priv;
>>>> + struct rockchip_pin_bank *bank;
>>>> + char *end = NULL;
>>>> + static int gpio;
>>>> + int id = -1, ret;
>>>> priv->regs = dev_read_addr_ptr(dev);
>>>> ret = uclass_first_device_err(UCLASS_PINCTRL, &priv->pinctrl);
>>>> - if (ret)
>>>> + if (ret) {
>>>> + dev_err(dev, "failed to get pinctrl device %d\n", ret);
>>>> return ret;
>>>> + }
>>>> +
>>>> + pctrl_priv = dev_get_priv(priv->pinctrl);
>>>> + if (!pctrl_priv) {
>>>> + dev_err(dev, "failed to get pinctrl priv\n");
>>>> + return -EINVAL;
>>>> + }
>>>> - uc_priv->gpio_count = ROCKCHIP_GPIOS_PER_BANK;
>>>> end = strrchr(dev->name, '@');
Question for the Rockchip U-boot maintainers:
Would you like to keep this method for backward compatibillity together with "gpio-ranges"?
All dtsi files must be changed first!
>>>> - priv->bank = trailing_strtoln(dev->name, end);
>>>> - priv->name[0] = 'A' + priv->bank;
>>>> - uc_priv->bank_name = priv->name;
>>>> + if (end)
>>>> + id = trailing_strtoln(dev->name, end);
>>>> + else
>>>> + dev_read_alias_seq(dev, &id);
>>>> +
>>>> + if (id < 0)
>>>> + id = gpio++;
>>>> +
>>>
>>> NACK. This does not work.
>>>
>>> This means that the gpio bank detection depends on:
>>> 1) the index of the alias (no guarantee it's stable/not overwritten by a
>>> board dts),
>>> 2) if no support for aliases (e.g. in TPL/SPL) or the alias does not exist,
>>> the probe order of the GPIO controller device will define its bank. This is
>>> somewhat working in the Linux kernel by chance but does NOT work in U-Boot
>>> (devices are probed only when used, so you could very well have gpio4
>>> controller probed before gpio0 and then gpio4 would represent bank 0 and
>>> then gpio0 represent bank 1).
>>>
>>> Yes, the current code will not work for "newer" DTS and needs to be adapted
>>> (FWIW, it does not work on PX30 already because the node name is gpio at addr
>>> instead of gpioX at addr), but the Linux kernel implementation (the one used
>>> above) is not correct and should not be used.
>>>
>>> I've two suggestions:
>>> 1) a rockchip,gpio-controller-bank = <0>; property in the -u-boot.dtsi for
>>> each gpio-controller and then you get the index from there in the driver,
>>> 2) get the register address of the node of the device you're currently
>>> probing and maintain a mapping of which address maps to which bank,
>>>
>>> We could also start a discussion with upstream Linux to see what they would
>>> like to go for so we don't have two different implementations.
>>
>> I see RFC patches for Linux to use a property called "gpio-ranges".
>> I'll wait for that to gain traction as a solution before I resubmit
>> this so that Linux/U-Boot use roughly the same method (assuming
>> Johan doesn't beat me to the punch, since it's his Linux patches
>> I'm following).
>>
>> Thank you.
>
> I see the mainline patches that Johan Jonker put together have been
> acked. Johan, are you going to also include these in U-Boot or would
> you like for me to try my hand at it here as part of this series?
If you have the time...
As you are already touching gpio with a common fall back string then it's best you do that in separate patch series.
Mind it involves a lot of dtsi changes before this can be merged.
Moving gpio nodes to root must also make it work both full U-boot and SPL reduced DT and with platdata if possible.
Johan
>
> Thank you.
>
>>
>>>
>>>> + if (id >= pctrl_priv->ctrl->nr_banks) {
>>>> + dev_err(dev, "bank id invalid\n");
>>>> + return -EINVAL;
>>>> + }
>>>> +
>>>> + bank = &pctrl_priv->ctrl->pin_banks[id];
>>>> + if (bank->bank_num != id) {
>>>> + dev_err(dev, "bank id mismatch with pinctrl\n");
>>>> + return -EINVAL;
>>>> + }
>>>> +
>>>> + priv->bank = bank->bank_num;
>>>> + uc_priv->gpio_count = bank->nr_pins;
>>>> + uc_priv->gpio_base = bank->pin_base;
>>>> + uc_priv->bank_name = bank->name;
>>>> return 0;
>>>> }
>>>> diff --git a/drivers/pinctrl/rockchip/Makefile b/drivers/pinctrl/rockchip/Makefile
>>>> index 7d03f8101d..c78fc2c331 100644
>>>> --- a/drivers/pinctrl/rockchip/Makefile
>>>> +++ b/drivers/pinctrl/rockchip/Makefile
>>>> @@ -14,4 +14,5 @@ obj-$(CONFIG_ROCKCHIP_RK3308) += pinctrl-rk3308.o
>>>> obj-$(CONFIG_ROCKCHIP_RK3328) += pinctrl-rk3328.o
>>>> obj-$(CONFIG_ROCKCHIP_RK3368) += pinctrl-rk3368.o
>>>> obj-$(CONFIG_ROCKCHIP_RK3399) += pinctrl-rk3399.o
>>>> +obj-$(CONFIG_ROCKCHIP_RK3568) += pinctrl-rk3568.o
>>>> obj-$(CONFIG_ROCKCHIP_RV1108) += pinctrl-rv1108.o
>>>> diff --git a/drivers/pinctrl/rockchip/pinctrl-rk3568.c b/drivers/pinctrl/rockchip/pinctrl-rk3568.c
>>>> new file mode 100644
>>>> index 0000000000..dce1c1e7ee
>>>> --- /dev/null
>>>> +++ b/drivers/pinctrl/rockchip/pinctrl-rk3568.c
>>>> @@ -0,0 +1,453 @@
>>>> +// SPDX-License-Identifier: GPL-2.0+
>>>> +/*
>>>> + * (C) Copyright 2020 Rockchip Electronics Co., Ltd
>>>> + */
>>>> +
>>>> +#include <common.h>
>>>> +#include <dm.h>
>>>> +#include <dm/pinctrl.h>
>>>> +#include <regmap.h>
>>>> +#include <syscon.h>
>>>> +
>>>> +#include "pinctrl-rockchip.h"
>>>> +
>>>> +static struct rockchip_mux_route_data rk3568_mux_route_data[] = {
>>>> + /* CAN0 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO0, RK_PB3, RK_FUNC_2, 0x0300, RK_GENMASK_VAL(0, 0, 0)),
>>>> + /* CAN0 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PA1, RK_FUNC_4, 0x0300, RK_GENMASK_VAL(0, 0, 1)),
>>>> + /* CAN1 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO1, RK_PA1, RK_FUNC_3, 0x0300, RK_GENMASK_VAL(2, 2, 0)),
>>>> + /* CAN1 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PC3, RK_FUNC_3, 0x0300, RK_GENMASK_VAL(2, 2, 1)),
>>>> + /* CAN2 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PB5, RK_FUNC_3, 0x0300, RK_GENMASK_VAL(4, 4, 0)),
>>>> + /* CAN2 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PB2, RK_FUNC_4, 0x0300, RK_GENMASK_VAL(4, 4, 1)),
>>>> + /* EDPDP_HPDIN IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PC4, RK_FUNC_1, 0x0300, RK_GENMASK_VAL(6, 6, 0)),
>>>> + /* EDPDP_HPDIN IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO0, RK_PC2, RK_FUNC_2, 0x0300, RK_GENMASK_VAL(6, 6, 1)),
>>>> + /* GMAC1 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PB1, RK_FUNC_3, 0x0300, RK_GENMASK_VAL(8, 8, 0)),
>>>> + /* GMAC1 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PA7, RK_FUNC_3, 0x0300, RK_GENMASK_VAL(8, 8, 1)),
>>>> + /* HDMITX IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PD1, RK_FUNC_1, 0x0300, RK_GENMASK_VAL(10, 10, 0)),
>>>> + /* HDMITX IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO0, RK_PC7, RK_FUNC_1, 0x0300, RK_GENMASK_VAL(10, 10, 1)),
>>>> + /* I2C2 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO0, RK_PB6, RK_FUNC_1, 0x0300, RK_GENMASK_VAL(14, 14, 0)),
>>>> + /* I2C2 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PB4, RK_FUNC_1, 0x0300, RK_GENMASK_VAL(14, 14, 1)),
>>>> + /* I2C3 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO1, RK_PA0, RK_FUNC_1, 0x0304, RK_GENMASK_VAL(0, 0, 0)),
>>>> + /* I2C3 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PB6, RK_FUNC_4, 0x0304, RK_GENMASK_VAL(0, 0, 1)),
>>>> + /* I2C4 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PB2, RK_FUNC_1, 0x0304, RK_GENMASK_VAL(2, 2, 0)),
>>>> + /* I2C4 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PB1, RK_FUNC_2, 0x0304, RK_GENMASK_VAL(2, 2, 1)),
>>>> + /* I2C5 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PB4, RK_FUNC_4, 0x0304, RK_GENMASK_VAL(4, 4, 0)),
>>>> + /* I2C5 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PD0, RK_FUNC_2, 0x0304, RK_GENMASK_VAL(4, 4, 1)),
>>>> + /* PWM4 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0304, RK_GENMASK_VAL(6, 6, 0)),
>>>> + /* PWM4 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0304, RK_GENMASK_VAL(6, 6, 1)),
>>>> + /* PWM5 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0304, RK_GENMASK_VAL(8, 8, 0)),
>>>> + /* PWM5 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0304, RK_GENMASK_VAL(8, 8, 1)),
>>>> + /* PWM6 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0304, RK_GENMASK_VAL(10, 10, 0)),
>>>> + /* PWM6 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0304, RK_GENMASK_VAL(10, 10, 1)),
>>>> + /* PWM7 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0304, RK_GENMASK_VAL(12, 12, 0)),
>>>> + /* PWM7 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0304, RK_GENMASK_VAL(12, 12, 1)),
>>>> + /* PWM8 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0304, RK_GENMASK_VAL(14, 14, 0)),
>>>> + /* PWM8 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0304, RK_GENMASK_VAL(14, 14, 1)),
>>>> + /* PWM9 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0308, RK_GENMASK_VAL(0, 0, 0)),
>>>> + /* PWM9 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0308, RK_GENMASK_VAL(0, 0, 1)),
>>>> + /* PWM10 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0308, RK_GENMASK_VAL(2, 2, 0)),
>>>> + /* PWM10 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0308, RK_GENMASK_VAL(2, 2, 1)),
>>>> + /* PWM11 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0308, RK_GENMASK_VAL(4, 4, 0)),
>>>> + /* PWM11 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0308, RK_GENMASK_VAL(4, 4, 1)),
>>>> + /* PWM12 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0308, RK_GENMASK_VAL(6, 6, 0)),
>>>> + /* PWM12 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0308, RK_GENMASK_VAL(6, 6, 1)),
>>>> + /* PWM13 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0308, RK_GENMASK_VAL(8, 8, 0)),
>>>> + /* PWM13 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0308, RK_GENMASK_VAL(8, 8, 1)),
>>>> + /* PWM14 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0308, RK_GENMASK_VAL(10, 10, 0)),
>>>> + /* PWM14 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0308, RK_GENMASK_VAL(10, 10, 1)),
>>>> + /* PWM15 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0308, RK_GENMASK_VAL(12, 12, 0)),
>>>> + /* PWM15 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0308, RK_GENMASK_VAL(12, 12, 1)),
>>>> + /* SDMMC2 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_3, 0x0308, RK_GENMASK_VAL(14, 14, 0)),
>>>> + /* SDMMC2 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PA5, RK_FUNC_5, 0x0308, RK_GENMASK_VAL(14, 14, 1)),
>>>> + /* SPI0 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO0, RK_PB5, RK_FUNC_2, 0x030c, RK_GENMASK_VAL(0, 0, 0)),
>>>> + /* SPI0 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PD3, RK_FUNC_3, 0x030c, RK_GENMASK_VAL(0, 0, 1)),
>>>> + /* SPI1 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PB5, RK_FUNC_3, 0x030c, RK_GENMASK_VAL(2, 2, 0)),
>>>> + /* SPI1 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PC3, RK_FUNC_3, 0x030c, RK_GENMASK_VAL(2, 2, 1)),
>>>> + /* SPI2 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PC1, RK_FUNC_4, 0x030c, RK_GENMASK_VAL(4, 4, 0)),
>>>> + /* SPI2 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PA0, RK_FUNC_3, 0x030c, RK_GENMASK_VAL(4, 4, 1)),
>>>> + /* SPI3 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PB3, RK_FUNC_4, 0x030c, RK_GENMASK_VAL(6, 6, 0)),
>>>> + /* SPI3 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PC2, RK_FUNC_2, 0x030c, RK_GENMASK_VAL(6, 6, 1)),
>>>> + /* UART1 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PB4, RK_FUNC_2, 0x030c, RK_GENMASK_VAL(8, 8, 0)),
>>>> + /* UART1 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO0, RK_PD1, RK_FUNC_1, 0x030c, RK_GENMASK_VAL(8, 8, 1)),
>>>> + /* UART2 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO0, RK_PD1, RK_FUNC_1, 0x030c, RK_GENMASK_VAL(10, 10, 0)),
>>>> + /* UART2 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO1, RK_PD5, RK_FUNC_2, 0x030c, RK_GENMASK_VAL(10, 10, 1)),
>>>> + /* UART3 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO1, RK_PA1, RK_FUNC_2, 0x030c, RK_GENMASK_VAL(12, 12, 0)),
>>>> + /* UART3 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PB7, RK_FUNC_4, 0x030c, RK_GENMASK_VAL(12, 12, 1)),
>>>> + /* UART4 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO1, RK_PA6, RK_FUNC_2, 0x030c, RK_GENMASK_VAL(14, 14, 0)),
>>>> + /* UART4 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PB2, RK_FUNC_4, 0x030c, RK_GENMASK_VAL(14, 14, 1)),
>>>> + /* UART5 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PA2, RK_FUNC_3, 0x0310, RK_GENMASK_VAL(0, 0, 0)),
>>>> + /* UART5 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PC2, RK_FUNC_4, 0x0310, RK_GENMASK_VAL(0, 0, 1)),
>>>> + /* UART6 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PA4, RK_FUNC_3, 0x0310, RK_GENMASK_VAL(2, 2, 0)),
>>>> + /* UART6 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO1, RK_PD5, RK_FUNC_3, 0x0310, RK_GENMASK_VAL(2, 2, 1)),
>>>> + /* UART7 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PA6, RK_FUNC_3, 0x0310, RK_GENMASK_VAL(5, 4, 0)),
>>>> + /* UART7 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PC4, RK_FUNC_4, 0x0310, RK_GENMASK_VAL(5, 4, 1)),
>>>> + /* UART7 IO mux selection M2 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD2, RK_FUNC_1, 0x0310, RK_GENMASK_VAL(5, 4, 2)),
>>>> + /* UART8 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PC5, RK_FUNC_3, 0x0310, RK_GENMASK_VAL(6, 6, 0)),
>>>> + /* UART8 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PD7, RK_FUNC_4, 0x0310, RK_GENMASK_VAL(6, 6, 1)),
>>>> + /* UART9 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PB0, RK_FUNC_3, 0x0310, RK_GENMASK_VAL(9, 8, 0)),
>>>> + /* UART9 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PC5, RK_FUNC_4, 0x0310, RK_GENMASK_VAL(9, 8, 1)),
>>>> + /* UART9 IO mux selection M2 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PA4, RK_FUNC_4, 0x0310, RK_GENMASK_VAL(9, 8, 2)),
>>>> + /* I2S1 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO1, RK_PA2, RK_FUNC_1, 0x0310, RK_GENMASK_VAL(11, 10, 0)),
>>>> + /* I2S1 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PC6, RK_FUNC_4, 0x0310, RK_GENMASK_VAL(11, 10, 1)),
>>>> + /* I2S1 IO mux selection M2 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PD0, RK_FUNC_5, 0x0310, RK_GENMASK_VAL(11, 10, 2)),
>>>> + /* I2S2 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PC1, RK_FUNC_1, 0x0310, RK_GENMASK_VAL(12, 12, 0)),
>>>> + /* I2S2 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PB6, RK_FUNC_5, 0x0310, RK_GENMASK_VAL(12, 12, 1)),
>>>> + /* I2S3 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PA2, RK_FUNC_4, 0x0310, RK_GENMASK_VAL(14, 14, 0)),
>>>> + /* I2S3 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PC2, RK_FUNC_5, 0x0310, RK_GENMASK_VAL(14, 14, 1)),
>>>> + /* PDM IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO1, RK_PA6, RK_FUNC_3, 0x0314, RK_GENMASK_VAL(0, 0, 0)),
>>>> + /* PDM IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO3, RK_PD6, RK_FUNC_5, 0x0314, RK_GENMASK_VAL(0, 0, 1)),
>>>> + /* PCIE20 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO0, RK_PA5, RK_FUNC_3, 0x0314, RK_GENMASK_VAL(3, 2, 0)),
>>>> + /* PCIE20 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PD0, RK_FUNC_4, 0x0314, RK_GENMASK_VAL(3, 2, 1)),
>>>> + /* PCIE20 IO mux selection M2 */
>>>> + MR_TOPGRF(RK_GPIO1, RK_PB0, RK_FUNC_4, 0x0314, RK_GENMASK_VAL(3, 2, 2)),
>>>> + /* PCIE30X1 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO0, RK_PA4, RK_FUNC_3, 0x0314, RK_GENMASK_VAL(5, 4, 0)),
>>>> + /* PCIE30X1 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PD2, RK_FUNC_4, 0x0314, RK_GENMASK_VAL(5, 4, 1)),
>>>> + /* PCIE30X1 IO mux selection M2 */
>>>> + MR_TOPGRF(RK_GPIO1, RK_PA5, RK_FUNC_4, 0x0314, RK_GENMASK_VAL(5, 4, 2)),
>>>> + /* PCIE30X2 IO mux selection M0 */
>>>> + MR_TOPGRF(RK_GPIO0, RK_PA6, RK_FUNC_2, 0x0314, RK_GENMASK_VAL(7, 6, 0)),
>>>> + /* PCIE30X2 IO mux selection M1 */
>>>> + MR_TOPGRF(RK_GPIO2, RK_PD4, RK_FUNC_4, 0x0314, RK_GENMASK_VAL(7, 6, 1)),
>>>> + /* PCIE30X2 IO mux selection M2 */
>>>> + MR_TOPGRF(RK_GPIO4, RK_PC2, RK_FUNC_4, 0x0314, RK_GENMASK_VAL(7, 6, 2)),
>>>> +};
>>>> +
>>>> +static int rk3568_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
>>>> +{
>>>> + struct rockchip_pinctrl_priv *priv = bank->priv;
>>>> + int iomux_num = (pin / 8);
>>>> + struct regmap *regmap;
>>>> + int reg, ret, mask;
>>>> + u8 bit;
>>>> + u32 data;
>>>> +
>>>> + debug("setting mux of GPIO%d-%d to %d\n", bank->bank_num, pin, mux);
>>>> +
>>>> + if (bank->iomux[iomux_num].type & IOMUX_SOURCE_PMU)
>>>> + regmap = priv->regmap_pmu;
>>>> + else
>>>> + regmap = priv->regmap_base;
>>>> +
>>>> + reg = bank->iomux[iomux_num].offset;
>>>> + if ((pin % 8) >= 4)
>>>> + reg += 0x4;
>>>> + bit = (pin % 4) * 4;
>>>> + mask = 0xf;
>>>> +
>>>> + data = (mask << (bit + 16));
>>>> + data |= (mux & mask) << bit;
>>>> + ret = regmap_write(regmap, reg, data);
>>>> +
>>>> + return ret;
>>>> +}
>>>> +
>>>> +#define RK3568_PULL_PMU_OFFSET 0x20
>>>> +#define RK3568_PULL_GRF_OFFSET 0x80
>>>> +#define RK3568_PULL_BITS_PER_PIN 2
>>>> +#define RK3568_PULL_PINS_PER_REG 8
>>>> +#define RK3568_PULL_BANK_STRIDE 0x10
>>>> +
>>>> +static void rk3568_calc_pull_reg_and_bit(struct rockchip_pin_bank *bank,
>>>> + int pin_num, struct regmap **regmap,
>>>> + int *reg, u8 *bit)
>>>> +{
>>>> + struct rockchip_pinctrl_priv *info = bank->priv;
>>>> +
>>>> + if (bank->bank_num == 0) {
>>>> + *regmap = info->regmap_pmu;
>>>> + *reg = RK3568_PULL_PMU_OFFSET;
>>>> + *reg += bank->bank_num * RK3568_PULL_BANK_STRIDE;
>>>> + } else {
>>>> + *regmap = info->regmap_base;
>>>> + *reg = RK3568_PULL_GRF_OFFSET;
>>>> + *reg += (bank->bank_num - 1) * RK3568_PULL_BANK_STRIDE;
>>>> + }
>>>> +
>>>> + *reg += ((pin_num / RK3568_PULL_PINS_PER_REG) * 4);
>>>> + *bit = (pin_num % RK3568_PULL_PINS_PER_REG);
>>>> + *bit *= RK3568_PULL_BITS_PER_PIN;
>>>> +}
>>>> +
>>>> +#define RK3568_DRV_PMU_OFFSET 0x70
>>>> +#define RK3568_DRV_GRF_OFFSET 0x200
>>>> +#define RK3568_DRV_BITS_PER_PIN 8
>>>> +#define RK3568_DRV_PINS_PER_REG 2
>>>> +#define RK3568_DRV_BANK_STRIDE 0x40
>>>> +
>>>> +static void rk3568_calc_drv_reg_and_bit(struct rockchip_pin_bank *bank,
>>>> + int pin_num, struct regmap **regmap,
>>>> + int *reg, u8 *bit)
>>>> +{
>>>> + struct rockchip_pinctrl_priv *info = bank->priv;
>>>> +
>>>> + /* The first 32 pins of the first bank are located in PMU */
>>>> + if (bank->bank_num == 0) {
>>>> + *regmap = info->regmap_pmu;
>>>> + *reg = RK3568_DRV_PMU_OFFSET;
>>>> + } else {
>>>> + *regmap = info->regmap_base;
>>>> + *reg = RK3568_DRV_GRF_OFFSET;
>>>> + *reg += (bank->bank_num - 1) * RK3568_DRV_BANK_STRIDE;
>>>> + }
>>>> +
>>>> + *reg += ((pin_num / RK3568_DRV_PINS_PER_REG) * 4);
>>>> + *bit = (pin_num % RK3568_DRV_PINS_PER_REG);
>>>> + *bit *= RK3568_DRV_BITS_PER_PIN;
>>>> +}
>>>> +
>>>> +#define RK3568_SCHMITT_BITS_PER_PIN 2
>>>> +#define RK3568_SCHMITT_PINS_PER_REG 8
>>>> +#define RK3568_SCHMITT_BANK_STRIDE 0x10
>>>> +#define RK3568_SCHMITT_GRF_OFFSET 0xc0
>>>> +#define RK3568_SCHMITT_PMUGRF_OFFSET 0x30
>>>> +
>>>> +static int rk3568_calc_schmitt_reg_and_bit(struct rockchip_pin_bank *bank,
>>>> + int pin_num, struct regmap **regmap,
>>>> + int *reg, u8 *bit)
>>>> +{
>>>> + struct rockchip_pinctrl_priv *info = bank->priv;
>>>> +
>>>> + if (bank->bank_num == 0) {
>>>> + *regmap = info->regmap_pmu;
>>>> + *reg = RK3568_SCHMITT_PMUGRF_OFFSET;
>>>> + } else {
>>>> + *regmap = info->regmap_base;
>>>> + *reg = RK3568_SCHMITT_GRF_OFFSET;
>>>> + *reg += (bank->bank_num - 1) * RK3568_SCHMITT_BANK_STRIDE;
>>>> + }
>>>> +
>>>> + *reg += ((pin_num / RK3568_SCHMITT_PINS_PER_REG) * 4);
>>>> + *bit = pin_num % RK3568_SCHMITT_PINS_PER_REG;
>>>> + *bit *= RK3568_SCHMITT_BITS_PER_PIN;
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int rk3568_set_pull(struct rockchip_pin_bank *bank,
>>>> + int pin_num, int pull)
>>>> +{
>>>> + struct regmap *regmap;
>>>> + int reg, ret;
>>>> + u8 bit, type;
>>>> + u32 data;
>>>> +
>>>> + if (pull == PIN_CONFIG_BIAS_PULL_PIN_DEFAULT)
>>>> + return -EOPNOTSUPP;
>>>> +
>>>> + rk3568_calc_pull_reg_and_bit(bank, pin_num, ®map, ®, &bit);
>>>> + type = bank->pull_type[pin_num / 8];
>>>> + ret = rockchip_translate_pull_value(type, pull);
>>>> + if (ret < 0) {
>>>> + debug("unsupported pull setting %d\n", pull);
>>>> + return ret;
>>>> + }
>>>> +
>>>> + /* enable the write to the equivalent lower bits */
>>>> + data = ((1 << ROCKCHIP_PULL_BITS_PER_PIN) - 1) << (bit + 16);
>>>> +
>>>> + data |= (ret << bit);
>>>> + ret = regmap_write(regmap, reg, data);
>>>> +
>>>> + return ret;
>>>> +}
>>>> +
>>>> +static int rk3568_set_drive(struct rockchip_pin_bank *bank,
>>>> + int pin_num, int strength)
>>>> +{
>>>> + struct regmap *regmap;
>>>> + int reg;
>>>> + u32 data;
>>>> + u8 bit;
>>>> + int drv = (1 << (strength + 1)) - 1;
>>>> + int ret = 0;
>>>> +
>>>> + rk3568_calc_drv_reg_and_bit(bank, pin_num, ®map, ®, &bit);
>>>> +
>>>> + /* enable the write to the equivalent lower bits */
>>>> + data = ((1 << RK3568_DRV_BITS_PER_PIN) - 1) << (bit + 16);
>>>> + data |= (drv << bit);
>>>> +
>>>> + ret = regmap_write(regmap, reg, data);
>>>> + if (ret)
>>>> + return ret;
>>>> +
>>>> + if (bank->bank_num == 1 && pin_num == 21)
>>>> + reg = 0x0840;
>>>> + else if (bank->bank_num == 2 && pin_num == 2)
>>>> + reg = 0x0844;
>>>> + else if (bank->bank_num == 2 && pin_num == 8)
>>>> + reg = 0x0848;
>>>> + else if (bank->bank_num == 3 && pin_num == 0)
>>>> + reg = 0x084c;
>>>> + else if (bank->bank_num == 3 && pin_num == 6)
>>>> + reg = 0x0850;
>>>> + else if (bank->bank_num == 4 && pin_num == 0)
>>>> + reg = 0x0854;
>>>> + else
>>>> + return 0;
>>>> +
>>>> + data = ((1 << RK3568_DRV_BITS_PER_PIN) - 1) << 16;
>>>> + data |= drv;
>>>> +
>>>> + return regmap_write(regmap, reg, data);
>>>> +}
>>>> +
>>>> +static int rk3568_set_schmitt(struct rockchip_pin_bank *bank,
>>>> + int pin_num, int enable)
>>>> +{
>>>> + struct regmap *regmap;
>>>> + int reg;
>>>> + u32 data;
>>>> + u8 bit;
>>>> +
>>>> + rk3568_calc_schmitt_reg_and_bit(bank, pin_num, ®map, ®, &bit);
>>>> +
>>>> + /* enable the write to the equivalent lower bits */
>>>> + data = ((1 << RK3568_SCHMITT_BITS_PER_PIN) - 1) << (bit + 16);
>>>> + data |= (enable << bit);
>>>> +
>>>> + return regmap_write(regmap, reg, data);
>>>> +}
>>>> +
>>>> +static struct rockchip_pin_bank rk3568_pin_banks[] = {
>>>> + PIN_BANK_IOMUX_FLAGS(0, 32, "gpio0", IOMUX_SOURCE_PMU | IOMUX_WIDTH_4BIT,
>>>> + IOMUX_SOURCE_PMU | IOMUX_WIDTH_4BIT,
>>>> + IOMUX_SOURCE_PMU | IOMUX_WIDTH_4BIT,
>>>> + IOMUX_SOURCE_PMU | IOMUX_WIDTH_4BIT),
>>>> + PIN_BANK_IOMUX_FLAGS(1, 32, "gpio1", IOMUX_WIDTH_4BIT,
>>>> + IOMUX_WIDTH_4BIT,
>>>> + IOMUX_WIDTH_4BIT,
>>>> + IOMUX_WIDTH_4BIT),
>>>> + PIN_BANK_IOMUX_FLAGS(2, 32, "gpio2", IOMUX_WIDTH_4BIT,
>>>> + IOMUX_WIDTH_4BIT,
>>>> + IOMUX_WIDTH_4BIT,
>>>> + IOMUX_WIDTH_4BIT),
>>>> + PIN_BANK_IOMUX_FLAGS(3, 32, "gpio3", IOMUX_WIDTH_4BIT,
>>>> + IOMUX_WIDTH_4BIT,
>>>> + IOMUX_WIDTH_4BIT,
>>>> + IOMUX_WIDTH_4BIT),
>>>> + PIN_BANK_IOMUX_FLAGS(4, 32, "gpio4", IOMUX_WIDTH_4BIT,
>>>> + IOMUX_WIDTH_4BIT,
>>>> + IOMUX_WIDTH_4BIT,
>>>> + IOMUX_WIDTH_4BIT),
>>>> +};
>>>> +
>>>> +static const struct rockchip_pin_ctrl rk3568_pin_ctrl = {
>>>> + .pin_banks = rk3568_pin_banks,
>>>> + .nr_banks = ARRAY_SIZE(rk3568_pin_banks),
>>>> + .nr_pins = 160,
>>>> + .grf_mux_offset = 0x0,
>>>> + .pmu_mux_offset = 0x0,
>>>> + .iomux_routes = rk3568_mux_route_data,
>>>> + .niomux_routes = ARRAY_SIZE(rk3568_mux_route_data),
>>>> + .set_mux = rk3568_set_mux,
>>>> + .set_pull = rk3568_set_pull,
>>>> + .set_drive = rk3568_set_drive,
>>>> + .set_schmitt = rk3568_set_schmitt,
>>>> +};
>>>> +
>>>> +static const struct udevice_id rk3568_pinctrl_ids[] = {
>>>> + {
>>>> + .compatible = "rockchip,rk3568-pinctrl",
>>>> + .data = (ulong)&rk3568_pin_ctrl
>>>> + },
>>>> + { }
>>>> +};
>>>> +
>>>> +U_BOOT_DRIVER(pinctrl_rk3568) = {
>>>> + .name = "rockchip_rk3568_pinctrl",
>>>> + .id = UCLASS_PINCTRL,
>>>> + .of_match = rk3568_pinctrl_ids,
>>>> + .priv_auto = sizeof(struct rockchip_pinctrl_priv),
>>>> + .ops = &rockchip_pinctrl_ops,
>>>> +#if !IS_ENABLED(CONFIG_OF_PLATDATA)
>>>> + .bind = dm_scan_fdt_dev,
>>>> +#endif
>>>> + .probe = rockchip_pinctrl_probe,
>>>> +};
>>>> diff --git a/drivers/pinctrl/rockchip/pinctrl-rockchip-core.c b/drivers/pinctrl/rockchip/pinctrl-rockchip-core.c
>>>> index 630513ba3a..5f0016ff60 100644
>>>> --- a/drivers/pinctrl/rockchip/pinctrl-rockchip-core.c
>>>> +++ b/drivers/pinctrl/rockchip/pinctrl-rockchip-core.c
>>>> @@ -400,7 +400,7 @@ static int rockchip_pinctrl_set_state(struct udevice *dev,
>>>> int prop_len, param;
>>>> const u32 *data;
>>>> ofnode node;
>>>> -#ifdef CONFIG_OF_LIVE
>>>> +#if CONFIG_IS_ENABLED(OF_LIVE)
>>>
>>> Not sure this is really related or not, would be better in its own commit I
>>> believe.
>>>
>>>> const struct device_node *np;
>>>> struct property *pp;
>>>> #else
>>>> @@ -440,7 +440,7 @@ static int rockchip_pinctrl_set_state(struct udevice *dev,
>>>> node = ofnode_get_by_phandle(conf);
>>>> if (!ofnode_valid(node))
>>>> return -ENODEV;
>>>> -#ifdef CONFIG_OF_LIVE
>>>> +#if CONFIG_IS_ENABLED(OF_LIVE)
>>>> np = ofnode_to_np(node);
>>>> for (pp = np->properties; pp; pp = pp->next) {
>>>> prop_name = pp->name;
>>>> @@ -515,13 +515,15 @@ static struct rockchip_pin_ctrl *rockchip_pinctrl_get_soc_data(struct udevice *d
>>>> /* preset iomux offset value, set new start value */
>>>> if (iom->offset >= 0) {
>>>> - if (iom->type & IOMUX_SOURCE_PMU)
>>>> + if ((iom->type & IOMUX_SOURCE_PMU) || \
>>>> + (iom->type & IOMUX_L_SOURCE_PMU))
>>>
>>> nitpick: Could be if (iom->type & (IOMUX_SOURCE_PMU | IOMUX_L_SOURCE_PMU))
>>> instead.
>>>
>>>> pmu_offs = iom->offset;
>>>> else
>>>> grf_offs = iom->offset;
>>>> } else { /* set current iomux offset */
>>>> - iom->offset = (iom->type & IOMUX_SOURCE_PMU) ?
>>>> - pmu_offs : grf_offs;
>>>> + iom->offset = ((iom->type & IOMUX_SOURCE_PMU) ||
>>>> + (iom->type & IOMUX_L_SOURCE_PMU)) ?
>>>
>>> Ditto.
>>>
>>> Cheers,
>>> Quentin
More information about the U-Boot
mailing list