[PATCH 69/88] arm: Rename STM32MP15x
Patrice CHOTARD
patrice.chotard at foss.st.com
Tue Jan 31 13:48:02 CET 2023
Hi Simon
On 1/23/23 23:00, Simon Glass wrote:
> CONFIG options must not use lower-case letter. Convert this and related
> ones to upper case.
>
> Signed-off-by: Simon Glass <sjg at chromium.org>
> ---
>
> arch/arm/dts/Makefile | 2 +-
> arch/arm/dts/stm32mp15-u-boot.dtsi | 2 +-
> arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi | 4 ++--
> arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi | 4 ++--
> arch/arm/mach-stm32mp/Kconfig | 6 +++---
> arch/arm/mach-stm32mp/Kconfig.15x | 6 +++---
> arch/arm/mach-stm32mp/Makefile | 2 +-
> arch/arm/mach-stm32mp/cmd_stm32key.c | 10 +++++-----
> .../mach-stm32mp/cmd_stm32prog/cmd_stm32prog.c | 2 +-
> .../arm/mach-stm32mp/cmd_stm32prog/stm32prog.c | 4 ++--
> .../arm/mach-stm32mp/cmd_stm32prog/stm32prog.h | 6 +++---
> arch/arm/mach-stm32mp/fdt.c | 8 ++++----
> arch/arm/mach-stm32mp/include/mach/stm32.h | 10 +++++-----
> arch/arm/mach-stm32mp/include/mach/stm32prog.h | 2 +-
> board/st/common/Kconfig | 14 +++++++-------
> board/st/common/stm32mp_mtdparts.c | 18 +++++++++---------
> board/st/stm32mp1/Kconfig | 2 +-
> board/st/stm32mp1/stm32mp1.c | 6 +++---
> configs/stm32mp15_basic_defconfig | 2 +-
> configs/stm32mp15_defconfig | 2 +-
> configs/stm32mp15_trusted_defconfig | 4 ++--
> drivers/clk/stm32/Kconfig | 2 +-
> 22 files changed, 59 insertions(+), 59 deletions(-)
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index dc8dcdff218..3c3efa6d6a3 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -1218,7 +1218,7 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
> dtb-$(CONFIG_STM32MP13X) += \
> stm32mp135f-dk.dtb
>
> -dtb-$(CONFIG_STM32MP15x) += \
> +dtb-$(CONFIG_STM32MP15X) += \
> stm32mp157a-dk1.dtb \
> stm32mp157a-dk1-scmi.dtb \
> stm32mp157a-icore-stm32mp1-ctouch2.dtb \
> diff --git a/arch/arm/dts/stm32mp15-u-boot.dtsi b/arch/arm/dts/stm32mp15-u-boot.dtsi
> index d5c87d29d88..955598b1c0b 100644
> --- a/arch/arm/dts/stm32mp15-u-boot.dtsi
> +++ b/arch/arm/dts/stm32mp15-u-boot.dtsi
> @@ -206,7 +206,7 @@
> resets = <&rcc UART8_R>;
> };
>
> -#if defined(CONFIG_STM32MP15x_STM32IMAGE)
> +#if defined(CONFIG_STM32MP15X_STM32IMAGE)
> &binman {
> u-boot-stm32 {
> filename = "u-boot.stm32";
> diff --git a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
> index 15a04ae927e..11062951923 100644
> --- a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
> +++ b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi
> @@ -21,13 +21,13 @@
> st,stm32prog-gpios = <&gpioa 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> };
>
> -#if defined(CONFIG_STM32MP15x_STM32IMAGE) || defined(CONFIG_SPL)
> +#if defined(CONFIG_STM32MP15X_STM32IMAGE) || defined(CONFIG_SPL)
> config {
> u-boot,mmc-env-partition = "ssbl";
> };
> #endif
>
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> /* only needed for boot with TF-A, witout FIP support */
> firmware {
> optee {
> diff --git a/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi b/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
> index 408abaf52fa..cea661bce68 100644
> --- a/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
> +++ b/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
> @@ -20,13 +20,13 @@
> st,stm32prog-gpios = <&gpioa 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> };
>
> -#if defined(CONFIG_STM32MP15x_STM32IMAGE) || defined(CONFIG_SPL)
> +#if defined(CONFIG_STM32MP15X_STM32IMAGE) || defined(CONFIG_SPL)
> config {
> u-boot,mmc-env-partition = "ssbl";
> };
> #endif
>
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> /* only needed for boot with TF-A, witout FIP support */
> firmware {
> optee {
> diff --git a/arch/arm/mach-stm32mp/Kconfig b/arch/arm/mach-stm32mp/Kconfig
> index cf3196b3b3a..f88b7dbffbd 100644
> --- a/arch/arm/mach-stm32mp/Kconfig
> +++ b/arch/arm/mach-stm32mp/Kconfig
> @@ -35,7 +35,7 @@ config ENV_SIZE
>
> choice
> prompt "Select STMicroelectronics STM32MPxxx Soc"
> - default STM32MP15x
> + default STM32MP15X
>
> config STM32MP13X
> bool "Support STMicroelectronics STM32MP13x Soc"
> @@ -55,7 +55,7 @@ config STM32MP13X
> support of STMicroelectronics SOC STM32MP13x family
> STMicroelectronics MPU with core ARMv7
>
> -config STM32MP15x
> +config STM32MP15X
> bool "Support STMicroelectronics STM32MP15x Soc"
> select ARCH_SUPPORT_PSCI
> select BINMAN
> @@ -103,7 +103,7 @@ config SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_MMC2
>
> config STM32_ETZPC
> bool "STM32 Extended TrustZone Protection"
> - depends on STM32MP15x || STM32MP13X
> + depends on STM32MP15X || STM32MP13X
> default y
> imply BOOTP_SERVERIP
> help
> diff --git a/arch/arm/mach-stm32mp/Kconfig.15x b/arch/arm/mach-stm32mp/Kconfig.15x
> index 1d32f8bf339..71c14eb4955 100644
> --- a/arch/arm/mach-stm32mp/Kconfig.15x
> +++ b/arch/arm/mach-stm32mp/Kconfig.15x
> @@ -1,6 +1,6 @@
> -if STM32MP15x
> +if STM32MP15X
>
> -config STM32MP15x_STM32IMAGE
> +config STM32MP15X_STM32IMAGE
> bool "Support STM32 image for generated U-Boot image"
> depends on TFABOOT
> help
> @@ -11,7 +11,7 @@ choice
> prompt "STM32MP15x board select"
> optional
>
> -config TARGET_ST_STM32MP15x
> +config TARGET_ST_STM32MP15X
> bool "STMicroelectronics STM32MP15x boards"
> imply BOOTSTAGE
> imply CMD_BOOTSTAGE
> diff --git a/arch/arm/mach-stm32mp/Makefile b/arch/arm/mach-stm32mp/Makefile
> index 90c7c121ec4..a40f8dc25a8 100644
> --- a/arch/arm/mach-stm32mp/Makefile
> +++ b/arch/arm/mach-stm32mp/Makefile
> @@ -9,7 +9,7 @@ obj-y += syscon.o
> obj-y += bsec.o
>
> obj-$(CONFIG_STM32MP13X) += stm32mp13x.o
> -obj-$(CONFIG_STM32MP15x) += stm32mp15x.o
> +obj-$(CONFIG_STM32MP15X) += stm32mp15x.o
>
> obj-$(CONFIG_STM32_ECDSA_VERIFY) += ecdsa_romapi.o
> ifdef CONFIG_SPL_BUILD
> diff --git a/arch/arm/mach-stm32mp/cmd_stm32key.c b/arch/arm/mach-stm32mp/cmd_stm32key.c
> index 96407cd9b18..b2e6421e9a2 100644
> --- a/arch/arm/mach-stm32mp/cmd_stm32key.c
> +++ b/arch/arm/mach-stm32mp/cmd_stm32key.c
> @@ -19,7 +19,7 @@
> */
> #define STM32_OTP_CLOSE_ID 0
> #define STM32_OTP_STM32MP13X_CLOSE_MASK 0x3F
> -#define STM32_OTP_STM32MP15x_CLOSE_MASK BIT(6)
> +#define STM32_OTP_STM32MP15X_CLOSE_MASK BIT(6)
>
> /* PKH is the first element of the key list */
> #define STM32KEY_PKH 0
> @@ -63,7 +63,7 @@ static u8 get_key_nb(void)
> if (IS_ENABLED(CONFIG_STM32MP13X))
> return ARRAY_SIZE(stm32mp13_list);
>
> - if (IS_ENABLED(CONFIG_STM32MP15x))
> + if (IS_ENABLED(CONFIG_STM32MP15X))
> return ARRAY_SIZE(stm32mp15_list);
> }
>
> @@ -72,7 +72,7 @@ static const struct stm32key *get_key(u8 index)
> if (IS_ENABLED(CONFIG_STM32MP13X))
> return &stm32mp13_list[index];
>
> - if (IS_ENABLED(CONFIG_STM32MP15x))
> + if (IS_ENABLED(CONFIG_STM32MP15X))
> return &stm32mp15_list[index];
> }
>
> @@ -81,8 +81,8 @@ static u32 get_otp_close_mask(void)
> if (IS_ENABLED(CONFIG_STM32MP13X))
> return STM32_OTP_STM32MP13X_CLOSE_MASK;
>
> - if (IS_ENABLED(CONFIG_STM32MP15x))
> - return STM32_OTP_STM32MP15x_CLOSE_MASK;
> + if (IS_ENABLED(CONFIG_STM32MP15X))
> + return STM32_OTP_STM32MP15X_CLOSE_MASK;
> }
>
> static int get_misc_dev(struct udevice **dev)
> diff --git a/arch/arm/mach-stm32mp/cmd_stm32prog/cmd_stm32prog.c b/arch/arm/mach-stm32mp/cmd_stm32prog/cmd_stm32prog.c
> index a8372356b0e..c9f99259054 100644
> --- a/arch/arm/mach-stm32mp/cmd_stm32prog/cmd_stm32prog.c
> +++ b/arch/arm/mach-stm32mp/cmd_stm32prog/cmd_stm32prog.c
> @@ -180,7 +180,7 @@ U_BOOT_CMD(stm32prog, 5, 0, do_stm32prog,
> " <size> = size of flashlayout (optional for image with STM32 header)\n"
> );
>
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> bool stm32prog_get_tee_partitions(void)
> {
> if (stm32prog_data)
> diff --git a/arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.c b/arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.c
> index 89552d2ad10..4b75397b1cc 100644
> --- a/arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.c
> +++ b/arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.c
> @@ -999,7 +999,7 @@ static int treat_partition_list(struct stm32prog_data *data)
> INIT_LIST_HEAD(&data->dev[j].part_list);
> }
>
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> data->tee_detected = false;
> #endif
> data->fsbl_nor_detected = false;
> @@ -1055,7 +1055,7 @@ static int treat_partition_list(struct stm32prog_data *data)
> /* fallthrough */
> case STM32PROG_NAND:
> case STM32PROG_SPI_NAND:
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> if (!data->tee_detected &&
> !strncmp(part->name, "tee", 3))
> data->tee_detected = true;
> diff --git a/arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.h b/arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.h
> index 58f4b96fa75..bcbbc2d5a35 100644
> --- a/arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.h
> +++ b/arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.h
> @@ -20,8 +20,8 @@
> #define DEFAULT_ADDRESS 0xFFFFFFFF
>
> #define CMD_SIZE 512
> -/* SMC is only supported in SPMIN for STM32MP15x */
> -#ifdef CONFIG_STM32MP15x
> +/* SMC is only supported in SPMIN for STM32MP15X */
> +#ifdef CONFIG_STM32MP15X
> #define OTP_SIZE_SMC 1024
> #else
> #define OTP_SIZE_SMC 0
> @@ -149,7 +149,7 @@ struct stm32prog_data {
> struct stm32prog_dev_t dev[STM32PROG_MAX_DEV]; /* array of device */
> int part_nb; /* nb of partition */
> struct stm32prog_part_t *part_array; /* array of partition */
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> bool tee_detected;
> #endif
> bool fsbl_nor_detected;
> diff --git a/arch/arm/mach-stm32mp/fdt.c b/arch/arm/mach-stm32mp/fdt.c
> index 6b69542ecfc..218d9ef282a 100644
> --- a/arch/arm/mach-stm32mp/fdt.c
> +++ b/arch/arm/mach-stm32mp/fdt.c
> @@ -275,7 +275,7 @@ static int stm32_fdt_fixup_etzpc(void *fdt, int soc_node)
> array_size = ARRAY_SIZE(stm32mp13_ip_addr);
> }
>
> - if (IS_ENABLED(CONFIG_STM32MP15x)) {
> + if (IS_ENABLED(CONFIG_STM32MP15X)) {
> array = stm32mp15_ip_addr;
> array_size = ARRAY_SIZE(stm32mp15_ip_addr);
> }
> @@ -494,7 +494,7 @@ int ft_system_setup(void *blob, struct bd_info *bd)
> if (IS_ENABLED(CONFIG_STM32MP13X))
> stm32mp13_fdt_fixup(blob, soc, cpu, name);
>
> - if (IS_ENABLED(CONFIG_STM32MP15x)) {
> + if (IS_ENABLED(CONFIG_STM32MP15X)) {
> stm32mp15_fdt_fixup(blob, soc, cpu, name);
>
> /*
> @@ -502,10 +502,10 @@ int ft_system_setup(void *blob, struct bd_info *bd)
> * copied from U-Boot device tree by optee_copy_fdt_nodes
> * when OP-TEE is not detected (probe failed)
> * these OP-TEE nodes are present in <board>-u-boot.dtsi
> - * under CONFIG_STM32MP15x_STM32IMAGE only for compatibility
> + * under CONFIG_STM32MP15X_STM32IMAGE only for compatibility
> * when FIP is not used by TF-A
> */
> - if (CONFIG_IS_ENABLED(STM32MP15x_STM32IMAGE) &&
> + if (CONFIG_IS_ENABLED(STM32MP15X_STM32IMAGE) &&
> !tee_find_device(NULL, NULL, NULL, NULL))
> stm32_fdt_disable_optee(blob);
> }
> diff --git a/arch/arm/mach-stm32mp/include/mach/stm32.h b/arch/arm/mach-stm32mp/include/mach/stm32.h
> index 1e1f694cb62..8f54b8ca94f 100644
> --- a/arch/arm/mach-stm32mp/include/mach/stm32.h
> +++ b/arch/arm/mach-stm32mp/include/mach/stm32.h
> @@ -17,7 +17,7 @@
> #define STM32_RCC_BASE 0x50000000
> #define STM32_PWR_BASE 0x50001000
> #define STM32_SYSCFG_BASE 0x50020000
> -#ifdef CONFIG_STM32MP15x
> +#ifdef CONFIG_STM32MP15X
> #define STM32_DBGMCU_BASE 0x50081000
> #endif
> #define STM32_FMC2_BASE 0x58002000
> @@ -28,7 +28,7 @@
> #define STM32_STGEN_BASE 0x5C008000
> #define STM32_TAMP_BASE 0x5C00A000
>
> -#ifdef CONFIG_STM32MP15x
> +#ifdef CONFIG_STM32MP15X
> #define STM32_USART1_BASE 0x5C000000
> #define STM32_USART2_BASE 0x4000E000
> #endif
> @@ -47,7 +47,7 @@
> #define STM32_SDMMC2_BASE 0x58007000
> #define STM32_SDMMC3_BASE 0x48004000
>
> -#ifdef CONFIG_STM32MP15x
> +#ifdef CONFIG_STM32MP15X
> #define STM32_SYSRAM_BASE 0x2FFC0000
> #define STM32_SYSRAM_SIZE SZ_256K
> #endif
> @@ -109,7 +109,7 @@ enum boot_device {
> /* TAMP registers */
> #define TAMP_BACKUP_REGISTER(x) (STM32_TAMP_BASE + 0x100 + 4 * x)
>
> -#ifdef CONFIG_STM32MP15x
> +#ifdef CONFIG_STM32MP15X
> #define TAMP_BACKUP_MAGIC_NUMBER TAMP_BACKUP_REGISTER(4)
> #define TAMP_BACKUP_BRANCH_ADDRESS TAMP_BACKUP_REGISTER(5)
> #define TAMP_FWU_BOOT_INFO_REG TAMP_BACKUP_REGISTER(10)
> @@ -160,7 +160,7 @@ enum forced_boot_mode {
> #define STM32_BSEC_LOCK(id) (STM32_BSEC_LOCK_OFFSET + (id) * 4)
>
> /* BSEC OTP index */
> -#ifdef CONFIG_STM32MP15x
> +#ifdef CONFIG_STM32MP15X
> #define BSEC_OTP_RPN 1
> #define BSEC_OTP_SERIAL 13
> #define BSEC_OTP_PKG 16
> diff --git a/arch/arm/mach-stm32mp/include/mach/stm32prog.h b/arch/arm/mach-stm32mp/include/mach/stm32prog.h
> index 99be4e1d656..573dffe6dd6 100644
> --- a/arch/arm/mach-stm32mp/include/mach/stm32prog.h
> +++ b/arch/arm/mach-stm32mp/include/mach/stm32prog.h
> @@ -11,7 +11,7 @@ int stm32prog_read_medium_virt(struct dfu_entity *dfu, u64 offset,
> void *buf, long *len);
> int stm32prog_get_medium_size_virt(struct dfu_entity *dfu, u64 *size);
>
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> bool stm32prog_get_tee_partitions(void);
> #endif
>
> diff --git a/board/st/common/Kconfig b/board/st/common/Kconfig
> index ba17d3158d1..20e28f9af82 100644
> --- a/board/st/common/Kconfig
> +++ b/board/st/common/Kconfig
> @@ -1,14 +1,14 @@
> config CMD_STBOARD
> bool "stboard - command for OTP board information"
> depends on ARCH_STM32MP
> - default y if TARGET_ST_STM32MP15x || TARGET_ST_STM32MP13X
> + default y if TARGET_ST_STM32MP15X || TARGET_ST_STM32MP13X
> help
> This compile the stboard command to
> read and write the board in the OTP.
>
> config MTDPARTS_NAND0_BOOT
> string "mtd boot partitions for nand0"
> - default "2m(fsbl),2m(ssbl1),2m(ssbl2)" if STM32MP15x_STM32IMAGE || \
> + default "2m(fsbl),2m(ssbl1),2m(ssbl2)" if STM32MP15X_STM32IMAGE || \
> !TFABOOT
> default "2m(fsbl),4m(fip1),4m(fip2)"
> depends on SYS_MTDPARTS_RUNTIME && ARCH_STM32MP
> @@ -23,7 +23,7 @@ config MTDPARTS_NAND0_BOOT
> config MTDPARTS_NAND0_TEE
> string "mtd tee partitions for nand0"
> default "512k(teeh),512k(teed),512k(teex)"
> - depends on SYS_MTDPARTS_RUNTIME && ARCH_STM32MP && STM32MP15x_STM32IMAGE
> + depends on SYS_MTDPARTS_RUNTIME && ARCH_STM32MP && STM32MP15X_STM32IMAGE
> help
> This define the tee partitions added in mtparts dynamically
> when tee is supported with boot from nand0.
> @@ -32,7 +32,7 @@ config MTDPARTS_NAND0_TEE
>
> config MTDPARTS_NOR0_BOOT
> string "mtd boot partitions for nor0"
> - default "256k(fsbl1),256k(fsbl2),2m(ssbl),512k(u-boot-env)" if STM32MP15x_STM32IMAGE || \
> + default "256k(fsbl1),256k(fsbl2),2m(ssbl),512k(u-boot-env)" if STM32MP15X_STM32IMAGE || \
> !TFABOOT
> default "256k(fsbl1),256k(fsbl2),4m(fip),512k(u-boot-env)"
> depends on SYS_MTDPARTS_RUNTIME && ARCH_STM32MP
> @@ -46,14 +46,14 @@ config MTDPARTS_NOR0_BOOT
> config MTDPARTS_NOR0_TEE
> string "mtd tee partitions for nor0"
> default "256k(teeh),512k(teed),256k(teex)"
> - depends on SYS_MTDPARTS_RUNTIME && ARCH_STM32MP && STM32MP15x_STM32IMAGE
> + depends on SYS_MTDPARTS_RUNTIME && ARCH_STM32MP && STM32MP15X_STM32IMAGE
> help
> This define the tee partitions added in mtparts dynamically
> when tee is supported with boot from nor0.
>
> config MTDPARTS_SPINAND0_BOOT
> string "mtd boot partitions for spi-nand0"
> - default "2m(fsbl),2m(ssbl1),2m(ssbl2)" if STM32MP15x_STM32IMAGE || !TFABOOT
> + default "2m(fsbl),2m(ssbl1),2m(ssbl2)" if STM32MP15X_STM32IMAGE || !TFABOOT
> default "2m(fsbl),4m(fip1),4m(fip2)"
> depends on SYS_MTDPARTS_RUNTIME && ARCH_STM32MP
> help
> @@ -66,7 +66,7 @@ config MTDPARTS_SPINAND0_BOOT
> config MTDPARTS_SPINAND0_TEE
> string "mtd tee partitions for spi-nand0"
> default "512k(teeh),512k(teed),512k(teex)"
> - depends on SYS_MTDPARTS_RUNTIME && ARCH_STM32MP && STM32MP15x_STM32IMAGE
> + depends on SYS_MTDPARTS_RUNTIME && ARCH_STM32MP && STM32MP15X_STM32IMAGE
> help
> This define the tee partitions added in mtparts dynamically
> when tee is supported with boot from spi-nand0,
> diff --git a/board/st/common/stm32mp_mtdparts.c b/board/st/common/stm32mp_mtdparts.c
> index 18878424c7a..bc2ce600287 100644
> --- a/board/st/common/stm32mp_mtdparts.c
> +++ b/board/st/common/stm32mp_mtdparts.c
> @@ -11,7 +11,7 @@
> #include <log.h>
> #include <mtd.h>
> #include <mtd_node.h>
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> #include <tee.h>
> #endif
> #include <asm/arch/stm32prog.h>
> @@ -33,7 +33,7 @@ static void board_set_mtdparts(const char *dev,
> char *mtdids,
> char *mtdparts,
> const char *boot,
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> const char *tee,
> #endif
> const char *user)
> @@ -59,7 +59,7 @@ static void board_set_mtdparts(const char *dev,
> strncat(mtdparts, ",", MTDPARTS_LEN);
> }
>
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> if (tee) {
> strncat(mtdparts, tee, MTDPARTS_LEN);
> strncat(mtdparts, ",", MTDPARTS_LEN);
> @@ -77,7 +77,7 @@ void board_mtdparts_default(const char **mtdids, const char **mtdparts)
> static char ids[MTDIDS_LEN + 1];
> static bool mtd_initialized;
> bool nor, nand, spinand, serial;
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> bool tee = false;
> #endif
>
> @@ -97,7 +97,7 @@ void board_mtdparts_default(const char **mtdids, const char **mtdparts)
> case BOOT_SERIAL_USB:
> serial = true;
> if (CONFIG_IS_ENABLED(CMD_STM32PROG)) {
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> tee = stm32prog_get_tee_partitions();
> #endif
> nor = stm32prog_get_fsbl_nor();
> @@ -118,7 +118,7 @@ void board_mtdparts_default(const char **mtdids, const char **mtdparts)
> break;
> }
>
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> if (!serial && tee_find_device(NULL, NULL, NULL, NULL))
> tee = true;
> #endif
> @@ -138,7 +138,7 @@ void board_mtdparts_default(const char **mtdids, const char **mtdparts)
> if (!IS_ERR_OR_NULL(mtd)) {
> board_set_mtdparts("nand0", ids, parts,
> CONFIG_MTDPARTS_NAND0_BOOT,
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> !nor && tee ? CONFIG_MTDPARTS_NAND0_TEE : NULL,
> #endif
> "-(UBI)");
> @@ -151,7 +151,7 @@ void board_mtdparts_default(const char **mtdids, const char **mtdparts)
> if (!IS_ERR_OR_NULL(mtd)) {
> board_set_mtdparts("spi-nand0", ids, parts,
> CONFIG_MTDPARTS_SPINAND0_BOOT,
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> !nor && tee ? CONFIG_MTDPARTS_SPINAND0_TEE : NULL,
> #endif
> "-(UBI)");
> @@ -163,7 +163,7 @@ void board_mtdparts_default(const char **mtdids, const char **mtdparts)
> if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev)) {
> board_set_mtdparts("nor0", ids, parts,
> CONFIG_MTDPARTS_NOR0_BOOT,
> -#ifdef CONFIG_STM32MP15x_STM32IMAGE
> +#ifdef CONFIG_STM32MP15X_STM32IMAGE
> tee ? CONFIG_MTDPARTS_NOR0_TEE : NULL,
> #endif
> "-(nor_user)");
> diff --git a/board/st/stm32mp1/Kconfig b/board/st/stm32mp1/Kconfig
> index 7d0d41bfea0..96de41546f1 100644
> --- a/board/st/stm32mp1/Kconfig
> +++ b/board/st/stm32mp1/Kconfig
> @@ -1,4 +1,4 @@
> -if TARGET_ST_STM32MP15x
> +if TARGET_ST_STM32MP15X
>
> config SYS_BOARD
> default "stm32mp1"
> diff --git a/board/st/stm32mp1/stm32mp1.c b/board/st/stm32mp1/stm32mp1.c
> index 47b3d1bf4c5..4536c1c673c 100644
> --- a/board/st/stm32mp1/stm32mp1.c
> +++ b/board/st/stm32mp1/stm32mp1.c
> @@ -114,7 +114,7 @@ int checkboard(void)
> int fdt_compat_len;
>
> if (IS_ENABLED(CONFIG_TFABOOT)) {
> - if (IS_ENABLED(CONFIG_STM32MP15x_STM32IMAGE))
> + if (IS_ENABLED(CONFIG_STM32MP15X_STM32IMAGE))
> mode = "trusted - stm32image";
> else
> mode = "trusted";
> @@ -616,7 +616,7 @@ error:
>
> static bool board_is_stm32mp15x_dk2(void)
> {
> - if (CONFIG_IS_ENABLED(TARGET_ST_STM32MP15x) &&
> + if (CONFIG_IS_ENABLED(TARGET_ST_STM32MP15X) &&
> of_machine_is_compatible("st,stm32mp157c-dk2"))
> return true;
>
> @@ -625,7 +625,7 @@ static bool board_is_stm32mp15x_dk2(void)
>
> static bool board_is_stm32mp15x_ev1(void)
> {
> - if (CONFIG_IS_ENABLED(TARGET_ST_STM32MP15x) &&
> + if (CONFIG_IS_ENABLED(TARGET_ST_STM32MP15X) &&
> (of_machine_is_compatible("st,stm32mp157a-ev1") ||
> of_machine_is_compatible("st,stm32mp157c-ev1") ||
> of_machine_is_compatible("st,stm32mp157d-ev1") ||
> diff --git a/configs/stm32mp15_basic_defconfig b/configs/stm32mp15_basic_defconfig
> index 87e3b496048..ea03751c781 100644
> --- a/configs/stm32mp15_basic_defconfig
> +++ b/configs/stm32mp15_basic_defconfig
> @@ -11,7 +11,7 @@ CONFIG_SPL_MMC=y
> CONFIG_SPL=y
> CONFIG_CMD_STM32KEY=y
> CONFIG_TYPEC_STUSB160X=y
> -CONFIG_TARGET_ST_STM32MP15x=y
> +CONFIG_TARGET_ST_STM32MP15X=y
> CONFIG_ENV_OFFSET_REDUND=0x2C0000
> CONFIG_CMD_STM32PROG=y
> CONFIG_SPL_SPI_FLASH_SUPPORT=y
> diff --git a/configs/stm32mp15_defconfig b/configs/stm32mp15_defconfig
> index 5dc00213a8f..54b80688c66 100644
> --- a/configs/stm32mp15_defconfig
> +++ b/configs/stm32mp15_defconfig
> @@ -9,7 +9,7 @@ CONFIG_SYS_PROMPT="STM32MP> "
> CONFIG_DDR_CACHEABLE_SIZE=0x10000000
> CONFIG_CMD_STM32KEY=y
> CONFIG_TYPEC_STUSB160X=y
> -CONFIG_TARGET_ST_STM32MP15x=y
> +CONFIG_TARGET_ST_STM32MP15X=y
> CONFIG_ENV_OFFSET_REDUND=0x4C0000
> CONFIG_CMD_STM32PROG=y
> # CONFIG_ARMV7_NONSEC is not set
> diff --git a/configs/stm32mp15_trusted_defconfig b/configs/stm32mp15_trusted_defconfig
> index c1ad4dd5213..3d80f410507 100644
> --- a/configs/stm32mp15_trusted_defconfig
> +++ b/configs/stm32mp15_trusted_defconfig
> @@ -9,8 +9,8 @@ CONFIG_SYS_PROMPT="STM32MP> "
> CONFIG_DDR_CACHEABLE_SIZE=0x10000000
> CONFIG_CMD_STM32KEY=y
> CONFIG_TYPEC_STUSB160X=y
> -CONFIG_STM32MP15x_STM32IMAGE=y
> -CONFIG_TARGET_ST_STM32MP15x=y
> +CONFIG_STM32MP15X_STM32IMAGE=y
> +CONFIG_TARGET_ST_STM32MP15X=y
> CONFIG_ENV_OFFSET_REDUND=0x2C0000
> CONFIG_CMD_STM32PROG=y
> # CONFIG_ARMV7_NONSEC is not set
> diff --git a/drivers/clk/stm32/Kconfig b/drivers/clk/stm32/Kconfig
> index 7dbddd032b8..c05015efe8b 100644
> --- a/drivers/clk/stm32/Kconfig
> +++ b/drivers/clk/stm32/Kconfig
> @@ -23,7 +23,7 @@ config CLK_STM32_CORE
> config CLK_STM32MP1
> bool "Enable RCC clock driver for STM32MP15"
> depends on ARCH_STM32MP && CLK
> - default y if STM32MP15x
> + default y if STM32MP15X
> help
> Enable the STM32 clock (RCC) driver. Enable support for
> manipulating STM32MP15's on-SoC clocks.
Reviewed-by: Patrice Chotard <patrice.chotard at foss.st.com>
Thanks
Patrice
More information about the U-Boot
mailing list