[PATCH v4 11/11] configs: starfive: Enable ID EEPROM configuration

[Jan Kiszka]

On 25.05.23 11:36, Yanhong Wang wrote:
> Enabled ID_EEPROM and I2C configuration for StarFive VisionFive2 board.
> 
> Signed-off-by: Yanhong Wang <yanhong.wang at starfivetech.com>
> ---
>  configs/starfive_visionfive2_defconfig | 19 ++++++++++++++++++-
>  1 file changed, 18 insertions(+), 1 deletion(-)
> 
> diff --git a/configs/starfive_visionfive2_defconfig b/configs/starfive_visionfive2_defconfig
> index c57708199d..570a1f53a1 100644
> --- a/configs/starfive_visionfive2_defconfig
> +++ b/configs/starfive_visionfive2_defconfig
> @@ -13,6 +13,7 @@ CONFIG_SYS_PROMPT="StarFive #"
>  CONFIG_OF_LIBFDT_OVERLAY=y
>  CONFIG_DM_RESET=y
>  CONFIG_SPL_MMC=y
> +CONFIG_SPL_DRIVERS_MISC=y
>  CONFIG_SPL_STACK=0x8180000
>  CONFIG_SPL=y
>  CONFIG_SPL_SPI_FLASH_SUPPORT=y
> @@ -23,6 +24,7 @@ CONFIG_SPL_OPENSBI_LOAD_ADDR=0x40000000
>  CONFIG_ARCH_RV64I=y
>  CONFIG_CMODEL_MEDANY=y
>  CONFIG_RISCV_SMODE=y
> +# CONFIG_OF_BOARD_FIXUP is not set
>  CONFIG_FIT=y
>  CONFIG_DISTRO_DEFAULTS=y
>  CONFIG_QSPI_BOOT=y
> @@ -34,6 +36,8 @@ CONFIG_PREBOOT="setenv fdt_addr ${fdtcontroladdr};fdt addr ${fdtcontroladdr};"
>  CONFIG_DEFAULT_FDT_FILE="starfive/jh7110-starfive-visionfive-2.dtb"
>  CONFIG_DISPLAY_CPUINFO=y
>  CONFIG_DISPLAY_BOARDINFO=y
> +CONFIG_ID_EEPROM=y
> +CONFIG_SYS_EEPROM_BUS_NUM=5
>  CONFIG_SPL_MAX_SIZE=0x40000
>  CONFIG_SPL_PAD_TO=0x0
>  CONFIG_SPL_BSS_START_ADDR=0x8040000
> @@ -45,21 +49,34 @@ CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x80000000
>  CONFIG_SYS_SPL_MALLOC_SIZE=0x400000
>  CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
>  CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=0x2
> +CONFIG_SPL_I2C=y
>  CONFIG_SPL_DM_SPI_FLASH=y
>  CONFIG_SPL_DM_RESET=y
>  CONFIG_SPL_SPI_LOAD=y
>  CONFIG_SYS_CBSIZE=256
>  CONFIG_SYS_PBSIZE=276
>  CONFIG_SYS_BOOTM_LEN=0x4000000
> +CONFIG_CMD_EEPROM=y
> +CONFIG_SYS_EEPROM_SIZE=512
> +CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=4
> +CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
>  CONFIG_CMD_MEMINFO=y
> +CONFIG_CMD_I2C=y
>  CONFIG_CMD_TFTPPUT=y
> +CONFIG_OF_BOARD=y
>  CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> +CONFIG_SPL_DM_SEQ_ALIAS=y
>  CONFIG_REGMAP=y
>  CONFIG_SYSCON=y
>  CONFIG_SPL_CLK_COMPOSITE_CCF=y
>  CONFIG_CLK_COMPOSITE_CCF=y
>  CONFIG_SPL_CLK_JH7110=y
> -# CONFIG_I2C is not set
> +CONFIG_DM_I2C=y
> +CONFIG_SYS_I2C_DW=y
> +CONFIG_MISC=y
> +CONFIG_I2C_EEPROM=y
> +CONFIG_SPL_I2C_EEPROM=y
> +CONFIG_SYS_I2C_EEPROM_ADDR=0X50
>  CONFIG_MMC_HS400_SUPPORT=y
>  CONFIG_SPL_MMC_HS400_SUPPORT=y
>  CONFIG_MMC_DW=y

This comes too late: Already patch 4 needs at least CONFIG_ID_EEPROM=y,
if not more.

Make sure you don't leave non-bisectable commit series behind. Whenever
something breaks (like 55171aedda88), people will use bisection to find
the causing commit, and then they will appreciate not having to deal
with such hick-ups.

Jan

-- 
Siemens AG, Technology
Competence Center Embedded Linux