[PATCH v4 11/11] configs: starfive: Enable ID EEPROM configuration

[Jan Kiszka]

On 07.06.23 04:19, yanhong wang wrote:
> 
> 
> On 2023/6/5 3:23, Jan Kiszka wrote:
>> On 25.05.23 11:36, Yanhong Wang wrote:
>>> Enabled ID_EEPROM and I2C configuration for StarFive VisionFive2 board.
>>>
>>> Signed-off-by: Yanhong Wang <yanhong.wang at starfivetech.com>
>>> ---
>>>  configs/starfive_visionfive2_defconfig | 19 ++++++++++++++++++-
>>>  1 file changed, 18 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/configs/starfive_visionfive2_defconfig b/configs/starfive_visionfive2_defconfig
>>> index c57708199d..570a1f53a1 100644
>>> --- a/configs/starfive_visionfive2_defconfig
>>> +++ b/configs/starfive_visionfive2_defconfig
>>> @@ -13,6 +13,7 @@ CONFIG_SYS_PROMPT="StarFive #"
>>>  CONFIG_OF_LIBFDT_OVERLAY=y
>>>  CONFIG_DM_RESET=y
>>>  CONFIG_SPL_MMC=y
>>> +CONFIG_SPL_DRIVERS_MISC=y
>>>  CONFIG_SPL_STACK=0x8180000
>>>  CONFIG_SPL=y
>>>  CONFIG_SPL_SPI_FLASH_SUPPORT=y
>>> @@ -23,6 +24,7 @@ CONFIG_SPL_OPENSBI_LOAD_ADDR=0x40000000
>>>  CONFIG_ARCH_RV64I=y
>>>  CONFIG_CMODEL_MEDANY=y
>>>  CONFIG_RISCV_SMODE=y
>>> +# CONFIG_OF_BOARD_FIXUP is not set
>>>  CONFIG_FIT=y
>>>  CONFIG_DISTRO_DEFAULTS=y
>>>  CONFIG_QSPI_BOOT=y
>>> @@ -34,6 +36,8 @@ CONFIG_PREBOOT="setenv fdt_addr ${fdtcontroladdr};fdt addr ${fdtcontroladdr};"
>>>  CONFIG_DEFAULT_FDT_FILE="starfive/jh7110-starfive-visionfive-2.dtb"
>>>  CONFIG_DISPLAY_CPUINFO=y
>>>  CONFIG_DISPLAY_BOARDINFO=y
>>> +CONFIG_ID_EEPROM=y
>>> +CONFIG_SYS_EEPROM_BUS_NUM=5
>>>  CONFIG_SPL_MAX_SIZE=0x40000
>>>  CONFIG_SPL_PAD_TO=0x0
>>>  CONFIG_SPL_BSS_START_ADDR=0x8040000
>>> @@ -45,21 +49,34 @@ CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x80000000
>>>  CONFIG_SYS_SPL_MALLOC_SIZE=0x400000
>>>  CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
>>>  CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=0x2
>>> +CONFIG_SPL_I2C=y
>>>  CONFIG_SPL_DM_SPI_FLASH=y
>>>  CONFIG_SPL_DM_RESET=y
>>>  CONFIG_SPL_SPI_LOAD=y
>>>  CONFIG_SYS_CBSIZE=256
>>>  CONFIG_SYS_PBSIZE=276
>>>  CONFIG_SYS_BOOTM_LEN=0x4000000
>>> +CONFIG_CMD_EEPROM=y
>>> +CONFIG_SYS_EEPROM_SIZE=512
>>> +CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=4
>>> +CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
>>>  CONFIG_CMD_MEMINFO=y
>>> +CONFIG_CMD_I2C=y
>>>  CONFIG_CMD_TFTPPUT=y
>>> +CONFIG_OF_BOARD=y
>>>  CONFIG_SYS_RELOC_GD_ENV_ADDR=y
>>> +CONFIG_SPL_DM_SEQ_ALIAS=y
>>>  CONFIG_REGMAP=y
>>>  CONFIG_SYSCON=y
>>>  CONFIG_SPL_CLK_COMPOSITE_CCF=y
>>>  CONFIG_CLK_COMPOSITE_CCF=y
>>>  CONFIG_SPL_CLK_JH7110=y
>>> -# CONFIG_I2C is not set
>>> +CONFIG_DM_I2C=y
>>> +CONFIG_SYS_I2C_DW=y
>>> +CONFIG_MISC=y
>>> +CONFIG_I2C_EEPROM=y
>>> +CONFIG_SPL_I2C_EEPROM=y
>>> +CONFIG_SYS_I2C_EEPROM_ADDR=0X50
>>>  CONFIG_MMC_HS400_SUPPORT=y
>>>  CONFIG_SPL_MMC_HS400_SUPPORT=y
>>>  CONFIG_MMC_DW=y
>>
>> This comes too late: Already patch 4 needs at least CONFIG_ID_EEPROM=y,
>> if not more.
>>
> 
> Moving patch 4 to the series end, is that okay?
> 

I didn't try. I would recommend that you to run a quick build check
after each patch being applied for the affected defconfig(s). Can be
automated (git rebase --exec ...).

Jan

-- 
Siemens AG, Technology
Competence Center Embedded Linux