[PATCH] mmc: Do not read eMMC partition access bits by default on OMAP2PLUS and BCM283X

Pali Rohár pali at kernel.org
Mon Jun 12 00:43:08 CEST 2023


Ping, what to do with this patch?
It is without any response too and is a is fix for this reported issue:
https://lore.kernel.org/u-boot/20230503171456.GF1134230@bill-the-cat/

On Tuesday 16 May 2023 20:49:43 Pali Rohár wrote:
> OMAP2PLUS and BCM283X mmc controllers do not work correctly with new emmc
> code which reads partition access bits prior mmc controller reset.
> 
> So introduce a new config option MMC_ENABLE_PART_ACCESS, which is by
> default disabled for ARCH_OMAP2PLUS and ARCH_BCM283X; and selected for
> 32-bit mvebu mmc booting (which requires it).
> 
> Signed-off-by: Pali Rohár <pali at kernel.org>
> ---
>  arch/arm/mach-mvebu/Kconfig |  1 +
>  drivers/mmc/Kconfig         | 12 ++++++++++++
>  drivers/mmc/mmc.c           |  2 ++
>  3 files changed, 15 insertions(+)
> 
> diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
> index ac484c73f62d..fe691cd435e7 100644
> --- a/arch/arm/mach-mvebu/Kconfig
> +++ b/arch/arm/mach-mvebu/Kconfig
> @@ -353,6 +353,7 @@ config MVEBU_SPL_BOOT_DEVICE_MMC
>  	imply SPL_GPIO
>  	imply SPL_LIBDISK_SUPPORT
>  	imply SPL_MMC
> +	select MMC_ENABLE_PART_ACCESS if SPL_MMC
>  	select SUPPORT_EMMC_BOOT if SPL_MMC
>  	select SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR if SPL_MMC
>  	select SPL_BOOTROM_SUPPORT
> diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
> index de01b9687bad..ea50dfdb62c5 100644
> --- a/drivers/mmc/Kconfig
> +++ b/drivers/mmc/Kconfig
> @@ -107,6 +107,18 @@ config MMC_HW_PARTITIONING
>  	  This adds a command and an API to do hardware partitioning on eMMC
>  	  devices.
>  
> +config MMC_ENABLE_PART_ACCESS
> +	bool "Support for MMC partition access bits"
> +	default n if ARCH_OMAP2PLUS || ARCH_BCM283X
> +	default y
> +	help
> +	  Read partition access bits from partition config register before card reset command
> +	  because these bits are reset to default value (User Data Area) during card reset.
> +	  This allows us to preserve original value of partition access bits used by the code
> +	  which loaded us (for example BootROM) and use it for board specific boot purposes.
> +	  .
> +	  This is required when U-Boot is using EXT_CSD_EXTRACT_PARTITION_ACCESS macro.
> +
>  config SUPPORT_EMMC_RPMB
>  	bool "Support eMMC replay protected memory block (RPMB)"
>  	imply CMD_MMC_RPMB
> diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c
> index 9915610d82b1..fa3c4d1937c1 100644
> --- a/drivers/mmc/mmc.c
> +++ b/drivers/mmc/mmc.c
> @@ -2864,6 +2864,7 @@ int mmc_get_op_cond(struct mmc *mmc, bool quiet)
>  retry:
>  	mmc_set_initial_state(mmc);
>  
> +#ifdef CONFIG_MMC_ENABLE_PART_ACCESS
>  	/*
>  	 * Read partition access bits from partition config register before card reset command
>  	 * because these bits are reset to default value (User Data Area) during card reset.
> @@ -2878,6 +2879,7 @@ retry:
>  		     ext_csd[EXT_CSD_BOOT_MULT]))
>  			mmc->part_config = ext_csd[EXT_CSD_PART_CONF] & PART_ACCESS_MASK;
>  	}
> +#endif
>  
>  	/* Reset the Card */
>  	err = mmc_go_idle(mmc);
> -- 
> 2.20.1
> 


More information about the U-Boot mailing list