[PATCH v1 2/3] riscv: dts: sync mpfs-icicle devicetree with linux
Padmarao.Begari at microchip.com
Padmarao.Begari at microchip.com
Tue Jun 13 07:31:06 CEST 2023
> On Wed, 2023-06-07 at 11:06 +0100, Conor Dooley wrote:
> The "notable" disappearances are:
> - the pac193x stanza - there's nothing in mainline linux w.r.t.
> bindings
> for this & what is going to appear in mainline linux is going to be
> incompatible with what is currently in U-Boot.
> - operating points - these operating points should not be set at the
> soc.dtsi level as they may not be possible depending on the design
> programmed to the FPGA
> - clock output names - there are defines for the clock indices, these
> should not be needed
> - the dt maintainers in linux NAKed using defines for IRQ numbers
> - the qspi nand, which is not part of the icicle's default
> configuration
> is removed.
>
> Signed-off-by: Conor Dooley <conor.dooley at microchip.com>
> ---
> arch/riscv/dts/mpfs-icicle-kit-fabric.dtsi | 71 +++
> arch/riscv/dts/mpfs-icicle-kit.dts | 190 +++++---
> arch/riscv/dts/mpfs.dtsi | 442 ++++++++------
> ----
> .../dt-bindings/clock/microchip-mpfs-clock.h | 29 +-
> .../microchip-mpfs-plic.h | 196 --------
> .../interrupt-controller/riscv-hart.h | 17 -
> 6 files changed, 420 insertions(+), 525 deletions(-)
> create mode 100644 arch/riscv/dts/mpfs-icicle-kit-fabric.dtsi
> delete mode 100644 include/dt-bindings/interrupt-
> controller/microchip-mpfs-plic.h
> delete mode 100644 include/dt-bindings/interrupt-controller/riscv-
> hart.h
>
Reviewed-by: Padmarao Begari <padmarao.begari at microchip.com>
Tested-by: Padmarao Begari <padmarao.begari at microchip.com>
> diff --git a/arch/riscv/dts/mpfs-icicle-kit-fabric.dtsi
> b/arch/riscv/dts/mpfs-icicle-kit-fabric.dtsi
> new file mode 100644
> index 0000000000..1069134f2e
> --- /dev/null
> +++ b/arch/riscv/dts/mpfs-icicle-kit-fabric.dtsi
> @@ -0,0 +1,71 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/* Copyright (c) 2020-2021 Microchip Technology Inc */
> +
> +/ {
> + compatible = "microchip,mpfs-icicle-reference-rtlv2210",
> "microchip,mpfs-icicle-kit",
> + "microchip,mpfs";
> +
> + core_pwm0: pwm at 40000000 {
> + compatible = "microchip,corepwm-rtl-v4";
> + reg = <0x0 0x40000000 0x0 0xF0>;
> + microchip,sync-update-mask = /bits/ 32 <0>;
> + #pwm-cells = <3>;
> + clocks = <&ccc_nw CLK_CCC_PLL0_OUT3>;
> + status = "disabled";
> + };
> +
> + i2c2: i2c at 40000200 {
> + compatible = "microchip,corei2c-rtl-v7";
> + reg = <0x0 0x40000200 0x0 0x100>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&ccc_nw CLK_CCC_PLL0_OUT3>;
> + interrupt-parent = <&plic>;
> + interrupts = <122>;
> + clock-frequency = <100000>;
> + status = "disabled";
> + };
> +
> + pcie: pcie at 3000000000 {
> + compatible = "microchip,pcie-host-1.0";
> + #address-cells = <0x3>;
> + #interrupt-cells = <0x1>;
> + #size-cells = <0x2>;
> + device_type = "pci";
> + reg = <0x30 0x0 0x0 0x8000000>, <0x0 0x43000000 0x0
> 0x10000>;
> + reg-names = "cfg", "apb";
> + bus-range = <0x0 0x7f>;
> + interrupt-parent = <&plic>;
> + interrupts = <119>;
> + interrupt-map = <0 0 0 1 &pcie_intc 0>,
> + <0 0 0 2 &pcie_intc 1>,
> + <0 0 0 3 &pcie_intc 2>,
> + <0 0 0 4 &pcie_intc 3>;
> + interrupt-map-mask = <0 0 0 7>;
> + clocks = <&ccc_nw CLK_CCC_PLL0_OUT1>, <&ccc_nw
> CLK_CCC_PLL0_OUT3>;
> + clock-names = "fic1", "fic3";
> + ranges = <0x3000000 0x0 0x8000000 0x30 0x8000000 0x0
> 0x80000000>;
> + dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000
> 0x1 0x00000000>;
> + msi-parent = <&pcie>;
> + msi-controller;
> + status = "disabled";
> + pcie_intc: interrupt-controller {
> + #address-cells = <0>;
> + #interrupt-cells = <1>;
> + interrupt-controller;
> + };
> + };
> +
> + refclk_ccc: cccrefclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + };
> +};
> +
> +&ccc_nw {
> + clocks = <&refclk_ccc>, <&refclk_ccc>, <&refclk_ccc>,
> <&refclk_ccc>,
> + <&refclk_ccc>, <&refclk_ccc>;
> + clock-names = "pll0_ref0", "pll0_ref1", "pll1_ref0",
> "pll1_ref1",
> + "dll0_ref", "dll1_ref";
> + status = "okay";
> +};
> diff --git a/arch/riscv/dts/mpfs-icicle-kit.dts
> b/arch/riscv/dts/mpfs-icicle-kit.dts
> index 3c56400b92..8aa5fb17d6 100644
> --- a/arch/riscv/dts/mpfs-icicle-kit.dts
> +++ b/arch/riscv/dts/mpfs-icicle-kit.dts
> @@ -7,29 +7,63 @@
> /dts-v1/;
>
> #include "mpfs.dtsi"
> +#include "mpfs-icicle-kit-fabric.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
>
> /* Clock frequency (in Hz) of the rtcclk */
> #define RTCCLK_FREQ 1000000
>
> / {
> model = "Microchip PolarFire-SoC Icicle Kit";
> - compatible = "microchip,mpfs-icicle-reference-rtlv2210",
> - "microchip,mpfs-icicle-kit", "microchip,mpfs";
> + compatible = "microchip,mpfs-icicle-reference-rtlv2210",
> "microchip,mpfs-icicle-kit",
> + "microchip,mpfs";
>
> aliases {
> - serial1 = &uart1;
> ethernet0 = &mac1;
> - spi0 = &qspi;
> + serial0 = &mmuart0;
> + serial1 = &mmuart1;
> + serial2 = &mmuart2;
> + serial3 = &mmuart3;
> + serial4 = &mmuart4;
> };
>
> chosen {
> - stdout-path = "serial1";
> + stdout-path = "serial1:115200n8";
> };
>
> cpus {
> timebase-frequency = <RTCCLK_FREQ>;
> };
>
> + leds {
> + compatible = "gpio-leds";
> +
> + led-1 {
> + gpios = <&gpio2 16 GPIO_ACTIVE_HIGH>;
> + color = <LED_COLOR_ID_RED>;
> + label = "led1";
> + };
> +
> + led-2 {
> + gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;
> + color = <LED_COLOR_ID_RED>;
> + label = "led2";
> + };
> +
> + led-3 {
> + gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>;
> + color = <LED_COLOR_ID_AMBER>;
> + label = "led3";
> + };
> +
> + led-4 {
> + gpios = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + color = <LED_COLOR_ID_AMBER>;
> + label = "led4";
> + };
> + };
> +
> ddrc_cache_lo: memory at 80000000 {
> device_type = "memory";
> reg = <0x0 0x80000000 0x0 0x40000000>;
> @@ -54,83 +88,121 @@
> };
> };
>
> -&refclk {
> - clock-frequency = <125000000>;
> +&core_pwm0 {
> + status = "okay";
> };
>
> -&uart1 {
> +&gpio2 {
> + interrupts = <53>, <53>, <53>, <53>,
> + <53>, <53>, <53>, <53>,
> + <53>, <53>, <53>, <53>,
> + <53>, <53>, <53>, <53>,
> + <53>, <53>, <53>, <53>,
> + <53>, <53>, <53>, <53>,
> + <53>, <53>, <53>, <53>,
> + <53>, <53>, <53>, <53>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +};
> +
> +&i2c1 {
> + status = "okay";
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&mac0 {
> + phy-mode = "sgmii";
> + phy-handle = <&phy0>;
> + status = "enabled";
> +};
> +
> +&mac1 {
> + phy-mode = "sgmii";
> + phy-handle = <&phy1>;
> + status = "okay";
> +
> + phy1: ethernet-phy at 9 {
> + reg = <9>;
> + };
> +
> + phy0: ethernet-phy at 8 {
> + reg = <8>;
> + };
> +};
> +
> +&mbox {
> status = "okay";
> };
>
> &mmc {
> - status = "okay";
> -
> bus-width = <4>;
> disable-wp;
> - cap-mmc-highspeed;
> cap-sd-highspeed;
> - card-detect-delay = <200>;
> + cap-mmc-highspeed;
> mmc-ddr-1_8v;
> mmc-hs200-1_8v;
> sd-uhs-sdr12;
> sd-uhs-sdr25;
> sd-uhs-sdr50;
> sd-uhs-sdr104;
> + status = "okay";
> };
>
> -&i2c1 {
> +&mmuart1 {
> status = "okay";
> - clock-frequency = <100000>;
> -
> - pac193x: pac193x at 10 {
> - compatible = "microchip,pac1934";
> - reg = <0x10>;
> - samp-rate = <64>;
> - status = "okay";
> - ch1: channel0 {
> - uohms-shunt-res = <10000>;
> - rail-name = "VDDREG";
> - channel_enabled;
> - };
> - ch2: channel1 {
> - uohms-shunt-res = <10000>;
> - rail-name = "VDDA25";
> - channel_enabled;
> - };
> - ch3: channel2 {
> - uohms-shunt-res = <10000>;
> - rail-name = "VDD25";
> - channel_enabled;
> - };
> - ch4: channel3 {
> - uohms-shunt-res = <10000>;
> - rail-name = "VDDA_REG";
> - channel_enabled;
> - };
> - };
> };
>
> -&mac1 {
> +&mmuart2 {
> + status = "okay";
> +};
> +
> +&mmuart3 {
> + status = "okay";
> +};
> +
> +&mmuart4 {
> + status = "okay";
> +};
> +
> +&pcie {
> status = "okay";
> - phy-mode = "sgmii";
> - phy-handle = <&phy1>;
> - phy1: ethernet-phy at 9 {
> - reg = <9>;
> - ti,fifo-depth = <0x1>;
> - };
> };
>
> &qspi {
> status = "okay";
> - num-cs = <1>;
> -
> - flash0: flash at 0 {
> - compatible = "spi-nand";
> - reg = <0x0>;
> - spi-tx-bus-width = <4>;
> - spi-rx-bus-width = <4>;
> - spi-max-frequency = <20000000>;
> - spi-cpol;
> - spi-cpha;
> - };
> +};
> +
> +&refclk {
> + clock-frequency = <125000000>;
> +};
> +
> +&refclk_ccc {
> + clock-frequency = <50000000>;
> +};
> +
> +&rtc {
> + status = "okay";
> +};
> +
> +&spi0 {
> + status = "okay";
> +};
> +
> +&spi1 {
> + status = "okay";
> +};
> +
> +&syscontroller {
> + status = "okay";
> +};
> +
> +&usb {
> + status = "okay";
> + dr_mode = "host";
> };
> diff --git a/arch/riscv/dts/mpfs.dtsi b/arch/riscv/dts/mpfs.dtsi
> index 891dd0918b..6012a28507 100644
> --- a/arch/riscv/dts/mpfs.dtsi
> +++ b/arch/riscv/dts/mpfs.dtsi
> @@ -2,8 +2,6 @@
> /* Copyright (c) 2020-2021 Microchip Technology Inc */
>
> #include "dt-bindings/clock/microchip-mpfs-clock.h"
> -#include "dt-bindings/interrupt-controller/microchip-mpfs-plic.h"
> -#include "dt-bindings/interrupt-controller/riscv-hart.h"
>
> / {
> #address-cells = <2>;
> @@ -11,9 +9,6 @@
> model = "Microchip PolarFire SoC";
> compatible = "microchip,mpfs";
>
> - chosen {
> - };
> -
> cpus {
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -28,12 +23,7 @@
> riscv,isa = "rv64imac";
> clocks = <&clkcfg CLK_CPU>;
> status = "disabled";
> - operating-points = <
> - /* kHz uV */
> - 600000 1100000
> - 300000 950000
> - 150000 750000
> - >;
> +
> cpu0_intc: interrupt-controller {
> #interrupt-cells = <1>;
> compatible = "riscv,cpu-intc";
> @@ -59,13 +49,9 @@
> riscv,isa = "rv64imafdc";
> clocks = <&clkcfg CLK_CPU>;
> tlb-split;
> + next-level-cache = <&cctrllr>;
> status = "okay";
> - operating-points = <
> - /* kHz uV */
> - 600000 1100000
> - 300000 950000
> - 150000 750000
> - >;
> +
> cpu1_intc: interrupt-controller {
> #interrupt-cells = <1>;
> compatible = "riscv,cpu-intc";
> @@ -91,13 +77,9 @@
> riscv,isa = "rv64imafdc";
> clocks = <&clkcfg CLK_CPU>;
> tlb-split;
> + next-level-cache = <&cctrllr>;
> status = "okay";
> - operating-points = <
> - /* kHz uV */
> - 600000 1100000
> - 300000 950000
> - 150000 750000
> - >;
> +
> cpu2_intc: interrupt-controller {
> #interrupt-cells = <1>;
> compatible = "riscv,cpu-intc";
> @@ -123,13 +105,9 @@
> riscv,isa = "rv64imafdc";
> clocks = <&clkcfg CLK_CPU>;
> tlb-split;
> + next-level-cache = <&cctrllr>;
> status = "okay";
> - operating-points = <
> - /* kHz uV */
> - 600000 1100000
> - 300000 950000
> - 150000 750000
> - >;
> +
> cpu3_intc: interrupt-controller {
> #interrupt-cells = <1>;
> compatible = "riscv,cpu-intc";
> @@ -155,273 +133,322 @@
> riscv,isa = "rv64imafdc";
> clocks = <&clkcfg CLK_CPU>;
> tlb-split;
> + next-level-cache = <&cctrllr>;
> status = "okay";
> - operating-points = <
> - /* kHz uV */
> - 600000 1100000
> - 300000 950000
> - 150000 750000
> - >;
> cpu4_intc: interrupt-controller {
> #interrupt-cells = <1>;
> compatible = "riscv,cpu-intc";
> interrupt-controller;
> };
> };
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&cpu0>;
> + };
> +
> + core1 {
> + cpu = <&cpu1>;
> + };
> +
> + core2 {
> + cpu = <&cpu2>;
> + };
> +
> + core3 {
> + cpu = <&cpu3>;
> + };
> +
> + core4 {
> + cpu = <&cpu4>;
> + };
> + };
> + };
> };
>
> - refclk: refclk {
> + refclk: mssrefclk {
> compatible = "fixed-clock";
> #clock-cells = <0>;
> };
>
> + syscontroller: syscontroller {
> + compatible = "microchip,mpfs-sys-controller";
> + mboxes = <&mbox 0>;
> + };
> +
> soc {
> #address-cells = <2>;
> #size-cells = <2>;
> - compatible = "microchip,mpfs-soc", "simple-bus";
> + compatible = "simple-bus";
> ranges;
>
> - clint: clint at 2000000 {
> - compatible = "sifive,clint0";
> - reg = <0x0 0x2000000 0x0 0xC000>;
> - interrupts-extended =
> - <&cpu0_intc HART_INT_M_SOFT
> &cpu0_intc HART_INT_M_TIMER
> - &cpu1_intc HART_INT_M_SOFT
> &cpu1_intc HART_INT_M_TIMER
> - &cpu2_intc HART_INT_M_SOFT
> &cpu2_intc HART_INT_M_TIMER
> - &cpu3_intc HART_INT_M_SOFT
> &cpu3_intc HART_INT_M_TIMER
> - &cpu4_intc HART_INT_M_SOFT
> &cpu4_intc HART_INT_M_TIMER>;
> - };
> -
> - cachecontroller: cache-controller at 2010000 {
> - compatible = "sifive,fu540-c000-ccache",
> "cache";
> + cctrllr: cache-controller at 2010000 {
> + compatible = "microchip,mpfs-ccache",
> "sifive,fu540-c000-ccache", "cache";
> reg = <0x0 0x2010000 0x0 0x1000>;
> - interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_L2_METADATA_CORR
> - PLIC_INT_L2_METADATA_UNCORR
> - PLIC_INT_L2_DATA_CORR>;
> cache-block-size = <64>;
> cache-level = <2>;
> cache-sets = <1024>;
> cache-size = <2097152>;
> cache-unified;
> + interrupt-parent = <&plic>;
> + interrupts = <1>, <3>, <4>, <2>;
> };
>
> - pdma: pdma at 3000000 {
> - compatible = "microchip,mpfs-pdma-
> uio","sifive,fu540-c000-pdma";
> - reg = <0x0 0x3000000 0x0 0x8000>;
> - interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_DMA_CH0_DONE
> PLIC_INT_DMA_CH0_ERR
> - PLIC_INT_DMA_CH1_DONE
> PLIC_INT_DMA_CH1_ERR
> - PLIC_INT_DMA_CH2_DONE
> PLIC_INT_DMA_CH2_ERR
> - PLIC_INT_DMA_CH3_DONE
> PLIC_INT_DMA_CH3_ERR>;
> - #dma-cells = <1>;
> + clint: clint at 2000000 {
> + compatible = "sifive,fu540-c000-clint",
> "sifive,clint0";
> + reg = <0x0 0x2000000 0x0 0xC000>;
> + interrupts-extended = <&cpu0_intc 3>,
> <&cpu0_intc 7>,
> + <&cpu1_intc 3>,
> <&cpu1_intc 7>,
> + <&cpu2_intc 3>,
> <&cpu2_intc 7>,
> + <&cpu3_intc 3>,
> <&cpu3_intc 7>,
> + <&cpu4_intc 3>,
> <&cpu4_intc 7>;
> };
>
> plic: interrupt-controller at c000000 {
> - compatible = "sifive,plic-1.0.0";
> + compatible = "sifive,fu540-c000-plic",
> "sifive,plic-1.0.0";
> reg = <0x0 0xc000000 0x0 0x4000000>;
> + #address-cells = <0>;
> #interrupt-cells = <1>;
> - riscv,ndev = <186>;
> interrupt-controller;
> - interrupts-extended = <&cpu0_intc
> HART_INT_M_EXT
> - &cpu1_intc HART_INT_M_EXT
> &cpu1_intc HART_INT_S_EXT
> - &cpu2_intc HART_INT_M_EXT
> &cpu2_intc HART_INT_S_EXT
> - &cpu3_intc HART_INT_M_EXT
> &cpu3_intc HART_INT_S_EXT
> - &cpu4_intc HART_INT_M_EXT
> &cpu4_intc HART_INT_S_EXT>;
> + interrupts-extended = <&cpu0_intc 11>,
> + <&cpu1_intc 11>,
> <&cpu1_intc 9>,
> + <&cpu2_intc 11>,
> <&cpu2_intc 9>,
> + <&cpu3_intc 11>,
> <&cpu3_intc 9>,
> + <&cpu4_intc 11>,
> <&cpu4_intc 9>;
> + riscv,ndev = <186>;
> + };
> +
> + pdma: dma-controller at 3000000 {
> + compatible = "sifive,fu540-c000-pdma",
> "sifive,pdma0";
> + reg = <0x0 0x3000000 0x0 0x8000>;
> + interrupt-parent = <&plic>;
> + interrupts = <5 6>, <7 8>, <9 10>, <11 12>;
> + dma-channels = <4>;
> + #dma-cells = <1>;
> };
>
> clkcfg: clkcfg at 20002000 {
> compatible = "microchip,mpfs-clkcfg";
> reg = <0x0 0x20002000 0x0 0x1000>, <0x0
> 0x3E001000 0x0 0x1000>;
> - reg-names = "mss_sysreg";
> clocks = <&refclk>;
> #clock-cells = <1>;
> - clock-output-names = "cpu", "axi", "ahb",
> "envm", /* 0-3 */
> - "mac0", "mac1", "mmc", "timer",
> /* 4-7 */
> - "mmuart0", "mmuart1", "mmuart2",
> "mmuart3", /* 8-11 */
> - "mmuart4", "spi0", "spi1", "i2c0",
> /* 12-15 */
> - "i2c1", "can0", "can1", "usb",
> /* 16-19 */
> - "rsvd", "rtc", "qspi", "gpio0",
> /* 20-23 */
> - "gpio1", "gpio2", "ddrc", "fic0",
> /* 24-27 */
> - "fic1", "fic2", "fic3", "athena",
> "cfm"; /* 28-32 */
> + #reset-cells = <1>;
> };
>
> - /* Common node entry for eMMC/SD */
> - mmc: mmc at 20008000 {
> - compatible = "microchip,mpfs-
> sd4hc","cdns,sd4hc";
> - reg = <0x0 0x20008000 0x0 0x1000>;
> - clocks = <&clkcfg CLK_MMC>;
> - interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_MMC_MAIN
> PLIC_INT_MMC_WAKEUP>;
> - max-frequency = <200000000>;
> + ccc_se: clock-controller at 38010000 {
> + compatible = "microchip,mpfs-ccc";
> + reg = <0x0 0x38010000 0x0 0x1000>, <0x0
> 0x38020000 0x0 0x1000>,
> + <0x0 0x39010000 0x0 0x1000>, <0x0
> 0x39020000 0x0 0x1000>;
> + #clock-cells = <1>;
> status = "disabled";
> };
>
> - uart0: serial at 20000000 {
> + ccc_ne: clock-controller at 38040000 {
> + compatible = "microchip,mpfs-ccc";
> + reg = <0x0 0x38040000 0x0 0x1000>, <0x0
> 0x38080000 0x0 0x1000>,
> + <0x0 0x39040000 0x0 0x1000>, <0x0
> 0x39080000 0x0 0x1000>;
> + #clock-cells = <1>;
> + status = "disabled";
> + };
> +
> + ccc_nw: clock-controller at 38100000 {
> + compatible = "microchip,mpfs-ccc";
> + reg = <0x0 0x38100000 0x0 0x1000>, <0x0
> 0x38200000 0x0 0x1000>,
> + <0x0 0x39100000 0x0 0x1000>, <0x0
> 0x39200000 0x0 0x1000>;
> + #clock-cells = <1>;
> + status = "disabled";
> + };
> +
> + ccc_sw: clock-controller at 38400000 {
> + compatible = "microchip,mpfs-ccc";
> + reg = <0x0 0x38400000 0x0 0x1000>, <0x0
> 0x38800000 0x0 0x1000>,
> + <0x0 0x39400000 0x0 0x1000>, <0x0
> 0x39800000 0x0 0x1000>;
> + #clock-cells = <1>;
> + status = "disabled";
> + };
> +
> + mmuart0: serial at 20000000 {
> compatible = "ns16550a";
> reg = <0x0 0x20000000 0x0 0x400>;
> reg-io-width = <4>;
> reg-shift = <2>;
> interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_MMUART0>;
> + interrupts = <90>;
> + current-speed = <115200>;
> clocks = <&clkcfg CLK_MMUART0>;
> status = "disabled"; /* Reserved for the HSS */
> };
>
> - uart1: serial at 20100000 {
> + mmuart1: serial at 20100000 {
> compatible = "ns16550a";
> reg = <0x0 0x20100000 0x0 0x400>;
> reg-io-width = <4>;
> reg-shift = <2>;
> interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_MMUART1>;
> + interrupts = <91>;
> + current-speed = <115200>;
> clocks = <&clkcfg CLK_MMUART1>;
> status = "disabled";
> };
>
> - uart2: serial at 20102000 {
> + mmuart2: serial at 20102000 {
> compatible = "ns16550a";
> reg = <0x0 0x20102000 0x0 0x400>;
> reg-io-width = <4>;
> reg-shift = <2>;
> interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_MMUART2>;
> + interrupts = <92>;
> + current-speed = <115200>;
> clocks = <&clkcfg CLK_MMUART2>;
> status = "disabled";
> };
>
> - uart3: serial at 20104000 {
> + mmuart3: serial at 20104000 {
> compatible = "ns16550a";
> reg = <0x0 0x20104000 0x0 0x400>;
> reg-io-width = <4>;
> reg-shift = <2>;
> interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_MMUART3>;
> + interrupts = <93>;
> + current-speed = <115200>;
> clocks = <&clkcfg CLK_MMUART3>;
> status = "disabled";
> };
>
> - uart4: serial at 20106000 {
> + mmuart4: serial at 20106000 {
> compatible = "ns16550a";
> reg = <0x0 0x20106000 0x0 0x400>;
> reg-io-width = <4>;
> reg-shift = <2>;
> interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_MMUART4>;
> + interrupts = <94>;
> clocks = <&clkcfg CLK_MMUART4>;
> + current-speed = <115200>;
> + status = "disabled";
> + };
> +
> + /* Common node entry for emmc/sd */
> + mmc: mmc at 20008000 {
> + compatible = "microchip,mpfs-sd4hc",
> "cdns,sd4hc";
> + reg = <0x0 0x20008000 0x0 0x1000>;
> + interrupt-parent = <&plic>;
> + interrupts = <88>;
> + clocks = <&clkcfg CLK_MMC>;
> + max-frequency = <200000000>;
> status = "disabled";
> };
>
> spi0: spi at 20108000 {
> compatible = "microchip,mpfs-spi";
> - reg = <0x0 0x20108000 0x0 0x1000>;
> - clocks = <&clkcfg CLK_SPI0>;
> - interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_SPI0>;
> - num-cs = <8>;
> #address-cells = <1>;
> #size-cells = <0>;
> + reg = <0x0 0x20108000 0x0 0x1000>;
> + interrupt-parent = <&plic>;
> + interrupts = <54>;
> + clocks = <&clkcfg CLK_SPI0>;
> status = "disabled";
> };
>
> spi1: spi at 20109000 {
> compatible = "microchip,mpfs-spi";
> - reg = <0x0 0x20109000 0x0 0x1000>;
> - clocks = <&clkcfg CLK_SPI1>;
> - interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_SPI1>;
> - num-cs = <8>;
> #address-cells = <1>;
> #size-cells = <0>;
> + reg = <0x0 0x20109000 0x0 0x1000>;
> + interrupt-parent = <&plic>;
> + interrupts = <55>;
> + clocks = <&clkcfg CLK_SPI1>;
> + status = "disabled";
> + };
> +
> + qspi: spi at 21000000 {
> + compatible = "microchip,mpfs-qspi",
> "microchip,coreqspi-rtl-v2";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0 0x21000000 0x0 0x1000>;
> + interrupt-parent = <&plic>;
> + interrupts = <85>;
> + clocks = <&clkcfg CLK_QSPI>;
> status = "disabled";
> };
>
> i2c0: i2c at 2010a000 {
> - compatible = "microchip,mpfs-i2c";
> + compatible = "microchip,mpfs-i2c",
> "microchip,corei2c-rtl-v7";
> reg = <0x0 0x2010a000 0x0 0x1000>;
> - clocks = <&clkcfg CLK_I2C0>;
> - interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_I2C0_MAIN>;
> #address-cells = <1>;
> #size-cells = <0>;
> + interrupt-parent = <&plic>;
> + interrupts = <58>;
> + clocks = <&clkcfg CLK_I2C0>;
> + clock-frequency = <100000>;
> status = "disabled";
> };
>
> i2c1: i2c at 2010b000 {
> - compatible = "microchip,mpfs-i2c";
> + compatible = "microchip,mpfs-i2c",
> "microchip,corei2c-rtl-v7";
> reg = <0x0 0x2010b000 0x0 0x1000>;
> - clocks = <&clkcfg CLK_I2C1>;
> - interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_I2C1_MAIN>;
> #address-cells = <1>;
> #size-cells = <0>;
> + interrupt-parent = <&plic>;
> + interrupts = <61>;
> + clocks = <&clkcfg CLK_I2C1>;
> + clock-frequency = <100000>;
> status = "disabled";
> };
>
> can0: can at 2010c000 {
> - compatible = "microchip,mpfs-can-uio";
> + compatible = "microchip,mpfs-can";
> reg = <0x0 0x2010c000 0x0 0x1000>;
> clocks = <&clkcfg CLK_CAN0>;
> interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_CAN0>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> + interrupts = <56>;
> status = "disabled";
> };
>
> can1: can at 2010d000 {
> - compatible = "microchip,mpfs-can-uio";
> + compatible = "microchip,mpfs-can";
> reg = <0x0 0x2010d000 0x0 0x1000>;
> clocks = <&clkcfg CLK_CAN1>;
> interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_CAN1>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> + interrupts = <57>;
> status = "disabled";
> };
>
> mac0: ethernet at 20110000 {
> - compatible = "cdns,macb";
> + compatible = "microchip,mpfs-macb",
> "cdns,macb";
> reg = <0x0 0x20110000 0x0 0x2000>;
> - clocks = <&clkcfg CLK_MAC0>, <&clkcfg CLK_AHB>;
> - clock-names = "pclk", "hclk";
> - interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_MAC0_INT
> - PLIC_INT_MAC0_QUEUE1
> - PLIC_INT_MAC0_QUEUE2
> - PLIC_INT_MAC0_QUEUE3
> - PLIC_INT_MAC0_EMAC
> - PLIC_INT_MAC0_MMSL>;
> - local-mac-address = [00 00 00 00 00 00];
> - status = "disabled";
> #address-cells = <1>;
> #size-cells = <0>;
> + interrupt-parent = <&plic>;
> + interrupts = <64>, <65>, <66>, <67>, <68>,
> <69>;
> + local-mac-address = [00 00 00 00 00 00];
> + clocks = <&clkcfg CLK_MAC0>, <&clkcfg CLK_AHB>;
> + clock-names = "pclk", "hclk";
> + resets = <&clkcfg CLK_MAC0>;
> + status = "disabled";
> };
>
> mac1: ethernet at 20112000 {
> - compatible = "cdns,macb";
> + compatible = "microchip,mpfs-macb",
> "cdns,macb";
> reg = <0x0 0x20112000 0x0 0x2000>;
> - clocks = <&clkcfg CLK_MAC1>, <&clkcfg CLK_AHB>;
> - clock-names = "pclk", "hclk";
> - interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_MAC1_INT
> - PLIC_INT_MAC1_QUEUE1
> - PLIC_INT_MAC1_QUEUE2
> - PLIC_INT_MAC1_QUEUE3
> - PLIC_INT_MAC1_EMAC
> - PLIC_INT_MAC1_MMSL>;
> - local-mac-address = [00 00 00 00 00 00];
> - status = "disabled";
> #address-cells = <1>;
> #size-cells = <0>;
> + interrupt-parent = <&plic>;
> + interrupts = <70>, <71>, <72>, <73>, <74>,
> <75>;
> + local-mac-address = [00 00 00 00 00 00];
> + clocks = <&clkcfg CLK_MAC1>, <&clkcfg CLK_AHB>;
> + clock-names = "pclk", "hclk";
> + resets = <&clkcfg CLK_MAC1>;
> + status = "disabled";
> };
>
> gpio0: gpio at 20120000 {
> compatible = "microchip,mpfs-gpio";
> reg = <0x0 0x20120000 0x0 0x1000>;
> - reg-names = "control";
> - clocks = <&clkcfg CLK_GPIO0>;
> interrupt-parent = <&plic>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + clocks = <&clkcfg CLK_GPIO0>;
> gpio-controller;
> #gpio-cells = <2>;
> status = "disabled";
> @@ -429,10 +456,11 @@
>
> gpio1: gpio at 20121000 {
> compatible = "microchip,mpfs-gpio";
> - reg = <000 0x20121000 0x0 0x1000>;
> - reg-names = "control";
> - clocks = <&clkcfg CLK_GPIO1>;
> + reg = <0x0 0x20121000 0x0 0x1000>;
> interrupt-parent = <&plic>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + clocks = <&clkcfg CLK_GPIO1>;
> gpio-controller;
> #gpio-cells = <2>;
> status = "disabled";
> @@ -441,9 +469,10 @@
> gpio2: gpio at 20122000 {
> compatible = "microchip,mpfs-gpio";
> reg = <0x0 0x20122000 0x0 0x1000>;
> - reg-names = "control";
> - clocks = <&clkcfg CLK_GPIO2>;
> interrupt-parent = <&plic>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + clocks = <&clkcfg CLK_GPIO2>;
> gpio-controller;
> #gpio-cells = <2>;
> status = "disabled";
> @@ -452,118 +481,31 @@
> rtc: rtc at 20124000 {
> compatible = "microchip,mpfs-rtc";
> reg = <0x0 0x20124000 0x0 0x1000>;
> - clocks = <&clkcfg CLK_RTC>;
> - clock-names = "rtc";
> interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_RTC_WAKEUP
> PLIC_INT_RTC_MATCH>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> + interrupts = <80>, <81>;
> + clocks = <&clkcfg CLK_RTC>, <&clkcfg
> CLK_RTCREF>;
> + clock-names = "rtc", "rtcref";
> status = "disabled";
> };
>
> usb: usb at 20201000 {
> - compatible = "microchip,mpfs-usb-host";
> + compatible = "microchip,mpfs-musb";
> reg = <0x0 0x20201000 0x0 0x1000>;
> - reg-names = "mc","control";
> + interrupt-parent = <&plic>;
> + interrupts = <86>, <87>;
> clocks = <&clkcfg CLK_USB>;
> - interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_USB_DMA
> PLIC_INT_USB_MC>;
> interrupt-names = "dma","mc";
> - dr_mode = "host";
> - status = "disabled";
> - };
> -
> - qspi: qspi at 21000000 {
> - compatible = "microchip,mpfs-qspi";
> - reg = <0x0 0x21000000 0x0 0x1000>;
> - clocks = <&clkcfg CLK_QSPI>;
> - interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_QSPI>;
> - num-cs = <8>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> status = "disabled";
> };
>
> mbox: mailbox at 37020000 {
> compatible = "microchip,mpfs-mailbox";
> - reg = <0x0 0x37020000 0x0 0x1000>, <0x0
> 0x2000318C 0x0 0x40>;
> + reg = <0x0 0x37020000 0x0 0x58>, <0x0
> 0x2000318C 0x0 0x40>,
> + <0x0 0x37020800 0x0 0x100>;
> interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_G5C_MESSAGE>;
> + interrupts = <96>;
> #mbox-cells = <1>;
> status = "disabled";
> };
> -
> - pcie: pcie at 2000000000 {
> - compatible = "microchip,pcie-host-1.0";
> - #address-cells = <0x3>;
> - #interrupt-cells = <0x1>;
> - #size-cells = <0x2>;
> - device_type = "pci";
> - reg = <0x20 0x0 0x0 0x8000000 0x0 0x43000000
> 0x0 0x10000>;
> - reg-names = "cfg", "apb";
> - clocks = <&clkcfg CLK_FIC0>, <&clkcfg
> CLK_FIC1>, <&clkcfg CLK_FIC3>;
> - clock-names = "fic0", "fic1", "fic3";
> - bus-range = <0x0 0x7f>;
> - interrupt-parent = <&plic>;
> - interrupts = <PLIC_INT_FABRIC_F2H_2>;
> - interrupt-map = <0 0 0 1 &pcie_intc 0>,
> - <0 0 0 2 &pcie_intc 1>,
> - <0 0 0 3 &pcie_intc 2>,
> - <0 0 0 4 &pcie_intc 3>;
> - interrupt-map-mask = <0 0 0 7>;
> - ranges = <0x3000000 0x0 0x8000000 0x20
> 0x8000000 0x0 0x80000000>;
> - msi-parent = <&pcie>;
> - msi-controller;
> - mchp,axi-m-atr0 = <0x10 0x0>;
> - status = "disabled";
> - pcie_intc: legacy-interrupt-controller {
> - #address-cells = <0>;
> - #interrupt-cells = <1>;
> - interrupt-controller;
> - };
> - };
> -
> - syscontroller: syscontroller {
> - compatible = "microchip,mpfs-sys-controller";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - mboxes = <&mbox 0>;
> - };
> -
> - hwrandom: hwrandom {
> - compatible = "microchip,mpfs-rng";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - syscontroller = <&syscontroller>;
> - };
> -
> - serialnum: serialnum {
> - compatible = "microchip,mpfs-serial-number";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - syscontroller = <&syscontroller>;
> - };
> -
> - fpgadigest: fpgadigest {
> - compatible = "microchip,mpfs-digest";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - syscontroller = <&syscontroller>;
> - };
> -
> - devicecert: cert {
> - compatible = "microchip,mpfs-device-cert";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - syscontroller = <&syscontroller>;
> - };
> -
> - signature: signature {
> - compatible = "microchip,mpfs-signature";
> - #address-cells = <1>;
> - #size-cells = <1>;
> - syscontroller = <&syscontroller>;
> - };
> };
> };
> diff --git a/include/dt-bindings/clock/microchip-mpfs-clock.h
> b/include/dt-bindings/clock/microchip-mpfs-clock.h
> index c7ed0a8db7..79775a5134 100644
> --- a/include/dt-bindings/clock/microchip-mpfs-clock.h
> +++ b/include/dt-bindings/clock/microchip-mpfs-clock.h
> @@ -1,7 +1,7 @@
> -/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
> +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
> /*
> - * Copyright (C) 2020 Microchip Technology Inc.
> - * Padmarao Begari <padmarao.begari at microchip.com>
> + * Daire McNamara,<daire.mcnamara at microchip.com>
> + * Copyright (C) 2020-2022 Microchip Technology Inc. All rights
> reserved.
> */
>
> #ifndef _DT_BINDINGS_CLK_MICROCHIP_MPFS_H_
> @@ -45,4 +45,27 @@
> #define CLK_RTCREF 33
> #define CLK_MSSPLL 34
>
> +/* Clock Conditioning Circuitry Clock IDs */
> +
> +#define CLK_CCC_PLL0 0
> +#define CLK_CCC_PLL1 1
> +#define CLK_CCC_DLL0 2
> +#define CLK_CCC_DLL1 3
> +
> +#define CLK_CCC_PLL0_OUT0 4
> +#define CLK_CCC_PLL0_OUT1 5
> +#define CLK_CCC_PLL0_OUT2 6
> +#define CLK_CCC_PLL0_OUT3 7
> +
> +#define CLK_CCC_PLL1_OUT0 8
> +#define CLK_CCC_PLL1_OUT1 9
> +#define CLK_CCC_PLL1_OUT2 10
> +#define CLK_CCC_PLL1_OUT3 11
> +
> +#define CLK_CCC_DLL0_OUT0 12
> +#define CLK_CCC_DLL0_OUT1 13
> +
> +#define CLK_CCC_DLL1_OUT0 14
> +#define CLK_CCC_DLL1_OUT1 15
> +
> #endif /* _DT_BINDINGS_CLK_MICROCHIP_MPFS_H_ */
> diff --git a/include/dt-bindings/interrupt-controller/microchip-mpfs-
> plic.h b/include/dt-bindings/interrupt-controller/microchip-mpfs-
> plic.h
> deleted file mode 100644
> index eba1bac7df..0000000000
> --- a/include/dt-bindings/interrupt-controller/microchip-mpfs-plic.h
> +++ /dev/null
> @@ -1,196 +0,0 @@
> -/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
> -/* Copyright (c) 2020-2021 Microchip Technology Inc */
> -
> -#ifndef _DT_BINDINGS_INTERRUPT_CONTROLLER_MICROCHIP_MPFS_PLIC_H
> -#define _DT_BINDINGS_INTERRUPT_CONTROLLER_MICROCHIP_MPFS_PLIC_H
> -
> -#define PLIC_INT_INVALID
> 0
> -#define PLIC_INT_L2_METADATA_CORR 1
> -#define PLIC_INT_L2_METADATA_UNCORR 2
> -#define PLIC_INT_L2_DATA_CORR
> 3
> -#define PLIC_INT_L2_DATA_UNCORR
> 4
> -#define PLIC_INT_DMA_CH0_DONE
> 5
> -#define PLIC_INT_DMA_CH0_ERR 6
> -#define PLIC_INT_DMA_CH1_DONE
> 7
> -#define PLIC_INT_DMA_CH1_ERR 8
> -#define PLIC_INT_DMA_CH2_DONE
> 9
> -#define PLIC_INT_DMA_CH2_ERR 10
> -#define PLIC_INT_DMA_CH3_DONE
> 11
> -#define PLIC_INT_DMA_CH3_ERR 12
> -
> -#define PLIC_INT_GPIO0_BIT0_OR_GPIO2_BIT0 13
> -#define PLIC_INT_GPIO0_BIT1_OR_GPIO2_BIT1 14
> -#define PLIC_INT_GPIO0_BIT2_OR_GPIO2_BIT2 15
> -#define PLIC_INT_GPIO0_BIT3_OR_GPIO2_BIT3 16
> -#define PLIC_INT_GPIO0_BIT4_OR_GPIO2_BIT4 17
> -#define PLIC_INT_GPIO0_BIT5_OR_GPIO2_BIT5 18
> -#define PLIC_INT_GPIO0_BIT6_OR_GPIO2_BIT6 19
> -#define PLIC_INT_GPIO0_BIT7_OR_GPIO2_BIT7 20
> -#define PLIC_INT_GPIO0_BIT8_OR_GPIO2_BIT8 21
> -#define PLIC_INT_GPIO0_BIT9_OR_GPIO2_BIT9 22
> -#define PLIC_INT_GPIO0_BIT10_OR_GPIO2_BIT10 23
> -#define PLIC_INT_GPIO0_BIT11_OR_GPIO2_BIT11 24
> -#define PLIC_INT_GPIO0_BIT12_OR_GPIO2_BIT12 25
> -#define PLIC_INT_GPIO0_BIT13_OR_GPIO2_BIT13 26
> -#define PLIC_INT_GPIO1_BIT0_OR_GPIO2_BIT14 27
> -#define PLIC_INT_GPIO1_BIT1_OR_GPIO2_BIT15 28
> -#define PLIC_INT_GPIO1_BIT2_OR_GPIO2_BIT16 29
> -#define PLIC_INT_GPIO1_BIT3_OR_GPIO2_BIT17 30
> -#define PLIC_INT_GPIO1_BIT4_OR_GPIO2_BIT18 31
> -#define PLIC_INT_GPIO1_BIT5_OR_GPIO2_BIT19 32
> -#define PLIC_INT_GPIO1_BIT6_OR_GPIO2_BIT20 33
> -#define PLIC_INT_GPIO1_BIT7_OR_GPIO2_BIT21 34
> -#define PLIC_INT_GPIO1_BIT8_OR_GPIO2_BIT22 35
> -#define PLIC_INT_GPIO1_BIT9_OR_GPIO2_BIT23 36
> -#define PLIC_INT_GPIO1_BIT10_OR_GPIO2_BIT24 37
> -#define PLIC_INT_GPIO1_BIT11_OR_GPIO2_BIT25 38
> -#define PLIC_INT_GPIO1_BIT12_OR_GPIO2_BIT26 39
> -#define PLIC_INT_GPIO1_BIT13_OR_GPIO2_BIT27 40
> -#define PLIC_INT_GPIO1_BIT14_OR_GPIO2_BIT28 41
> -#define PLIC_INT_GPIO1_BIT15_OR_GPIO2_BIT29 42
> -#define PLIC_INT_GPIO1_BIT16_OR_GPIO2_BIT30 43
> -#define PLIC_INT_GPIO1_BIT17_OR_GPIO2_BIT31 44
> -#define PLIC_INT_GPIO1_BIT18 45
> -#define PLIC_INT_GPIO1_BIT19 46
> -#define PLIC_INT_GPIO1_BIT20 47
> -#define PLIC_INT_GPIO1_BIT21 48
> -#define PLIC_INT_GPIO1_BIT22 49
> -#define PLIC_INT_GPIO1_BIT23 50
> -#define PLIC_INT_GPIO0_NON_DIRECT 51
> -#define PLIC_INT_GPIO1_NON_DIRECT 52
> -#define PLIC_INT_GPIO2_NON_DIRECT 53
> -#define PLIC_INT_SPI0
> 54
> -#define PLIC_INT_SPI1
> 55
> -#define PLIC_INT_CAN0
> 56
> -#define PLIC_INT_CAN1
> 57
> -#define PLIC_INT_I2C0_MAIN
> 58
> -#define PLIC_INT_I2C0_ALERT
> 59
> -#define PLIC_INT_I2C0_SUS
> 60
> -#define PLIC_INT_I2C1_MAIN
> 61
> -#define PLIC_INT_I2C1_ALERT
> 62
> -#define PLIC_INT_I2C1_SUS
> 63
> -#define PLIC_INT_MAC0_INT
> 64
> -#define PLIC_INT_MAC0_QUEUE1 65
> -#define PLIC_INT_MAC0_QUEUE2 66
> -#define PLIC_INT_MAC0_QUEUE3 67
> -#define PLIC_INT_MAC0_EMAC
> 68
> -#define PLIC_INT_MAC0_MMSL
> 69
> -#define PLIC_INT_MAC1_INT
> 70
> -#define PLIC_INT_MAC1_QUEUE1 71
> -#define PLIC_INT_MAC1_QUEUE2 72
> -#define PLIC_INT_MAC1_QUEUE3 73
> -#define PLIC_INT_MAC1_EMAC
> 74
> -#define PLIC_INT_MAC1_MMSL
> 75
> -#define PLIC_INT_DDRC_TRAIN
> 76
> -#define PLIC_INT_SCB_INTERRUPT
> 77
> -#define PLIC_INT_ECC_ERROR
> 78
> -#define PLIC_INT_ECC_CORRECT 79
> -#define PLIC_INT_RTC_WAKEUP
> 80
> -#define PLIC_INT_RTC_MATCH
> 81
> -#define PLIC_INT_TIMER1
> 82
> -#define PLIC_INT_TIMER2
> 83
> -#define PLIC_INT_ENVM
> 84
> -#define PLIC_INT_QSPI
> 85
> -#define PLIC_INT_USB_DMA
> 86
> -#define PLIC_INT_USB_MC
> 87
> -#define PLIC_INT_MMC_MAIN
> 88
> -#define PLIC_INT_MMC_WAKEUP
> 89
> -#define PLIC_INT_MMUART0
> 90
> -#define PLIC_INT_MMUART1
> 91
> -#define PLIC_INT_MMUART2
> 92
> -#define PLIC_INT_MMUART3
> 93
> -#define PLIC_INT_MMUART4
> 94
> -#define PLIC_INT_G5C_DEVRST
> 95
> -#define PLIC_INT_G5C_MESSAGE 96
> -#define PLIC_INT_USOC_VC_INTERRUPT 97
> -#define PLIC_INT_USOC_SMB_INTERRUPT 98
> -#define PLIC_INT_E51_0_MAINTENACE 99
> -#define PLIC_INT_WDOG0_MRVP
> 100
> -#define PLIC_INT_WDOG1_MRVP
> 101
> -#define PLIC_INT_WDOG2_MRVP
> 102
> -#define PLIC_INT_WDOG3_MRVP
> 103
> -#define PLIC_INT_WDOG4_MRVP
> 104
> -#define PLIC_INT_WDOG0_TOUT
> 105
> -#define PLIC_INT_WDOG1_TOUT
> 106
> -#define PLIC_INT_WDOG2_TOUT
> 107
> -#define PLIC_INT_WDOG3_TOUT
> 108
> -#define PLIC_INT_WDOG4_TOUT
> 109
> -#define PLIC_INT_G5C_MSS_SPI 110
> -#define PLIC_INT_VOLT_TEMP_ALARM 111
> -#define PLIC_INT_ATHENA_COMPLETE 112
> -#define PLIC_INT_ATHENA_ALARM
> 113
> -#define PLIC_INT_ATHENA_BUS_ERROR 114
> -#define PLIC_INT_USOC_AXIC_US
> 115
> -#define PLIC_INT_USOC_AXIC_DS
> 116
> -#define PLIC_INT_SPARE
> 117
> -#define PLIC_INT_FABRIC_F2H_0
> 118
> -#define PLIC_INT_FABRIC_F2H_1
> 119
> -#define PLIC_INT_FABRIC_F2H_2
> 120
> -#define PLIC_INT_FABRIC_F2H_3
> 121
> -#define PLIC_INT_FABRIC_F2H_4
> 122
> -#define PLIC_INT_FABRIC_F2H_5
> 123
> -#define PLIC_INT_FABRIC_F2H_6
> 124
> -#define PLIC_INT_FABRIC_F2H_7
> 125
> -#define PLIC_INT_FABRIC_F2H_8
> 126
> -#define PLIC_INT_FABRIC_F2H_9
> 127
> -#define PLIC_INT_FABRIC_F2H_10
> 128
> -#define PLIC_INT_FABRIC_F2H_11
> 129
> -#define PLIC_INT_FABRIC_F2H_12
> 130
> -#define PLIC_INT_FABRIC_F2H_13
> 131
> -#define PLIC_INT_FABRIC_F2H_14
> 132
> -#define PLIC_INT_FABRIC_F2H_15
> 133
> -#define PLIC_INT_FABRIC_F2H_16
> 134
> -#define PLIC_INT_FABRIC_F2H_17
> 135
> -#define PLIC_INT_FABRIC_F2H_18
> 136
> -#define PLIC_INT_FABRIC_F2H_19
> 137
> -#define PLIC_INT_FABRIC_F2H_20
> 138
> -#define PLIC_INT_FABRIC_F2H_21
> 139
> -#define PLIC_INT_FABRIC_F2H_22
> 140
> -#define PLIC_INT_FABRIC_F2H_23
> 141
> -#define PLIC_INT_FABRIC_F2H_24
> 142
> -#define PLIC_INT_FABRIC_F2H_25
> 143
> -#define PLIC_INT_FABRIC_F2H_26
> 144
> -#define PLIC_INT_FABRIC_F2H_27
> 145
> -#define PLIC_INT_FABRIC_F2H_28
> 146
> -#define PLIC_INT_FABRIC_F2H_29
> 147
> -#define PLIC_INT_FABRIC_F2H_30
> 148
> -#define PLIC_INT_FABRIC_F2H_31
> 149
> -#define PLIC_INT_FABRIC_F2H_32
> 150
> -#define PLIC_INT_FABRIC_F2H_33
> 151
> -#define PLIC_INT_FABRIC_F2H_34
> 152
> -#define PLIC_INT_FABRIC_F2H_35
> 153
> -#define PLIC_INT_FABRIC_F2H_36
> 154
> -#define PLIC_INT_FABRIC_F2H_37
> 155
> -#define PLIC_INT_FABRIC_F2H_38
> 156
> -#define PLIC_INT_FABRIC_F2H_39
> 157
> -#define PLIC_INT_FABRIC_F2H_40
> 158
> -#define PLIC_INT_FABRIC_F2H_41
> 159
> -#define PLIC_INT_FABRIC_F2H_42
> 160
> -#define PLIC_INT_FABRIC_F2H_43
> 161
> -#define PLIC_INT_FABRIC_F2H_44
> 162
> -#define PLIC_INT_FABRIC_F2H_45
> 163
> -#define PLIC_INT_FABRIC_F2H_46
> 164
> -#define PLIC_INT_FABRIC_F2H_47
> 165
> -#define PLIC_INT_FABRIC_F2H_48
> 166
> -#define PLIC_INT_FABRIC_F2H_49
> 167
> -#define PLIC_INT_FABRIC_F2H_50
> 168
> -#define PLIC_INT_FABRIC_F2H_51
> 169
> -#define PLIC_INT_FABRIC_F2H_52
> 170
> -#define PLIC_INT_FABRIC_F2H_53
> 171
> -#define PLIC_INT_FABRIC_F2H_54
> 172
> -#define PLIC_INT_FABRIC_F2H_55
> 173
> -#define PLIC_INT_FABRIC_F2H_56
> 174
> -#define PLIC_INT_FABRIC_F2H_57
> 175
> -#define PLIC_INT_FABRIC_F2H_58
> 176
> -#define PLIC_INT_FABRIC_F2H_59
> 177
> -#define PLIC_INT_FABRIC_F2H_60
> 178
> -#define PLIC_INT_FABRIC_F2H_61
> 179
> -#define PLIC_INT_FABRIC_F2H_62
> 180
> -#define PLIC_INT_FABRIC_F2H_63
> 181
> -#define PLIC_INT_BUS_ERROR_UNIT_HART_0 182
> -#define PLIC_INT_BUS_ERROR_UNIT_HART_1 183
> -#define PLIC_INT_BUS_ERROR_UNIT_HART_2 184
> -#define PLIC_INT_BUS_ERROR_UNIT_HART_3 185
> -#define PLIC_INT_BUS_ERROR_UNIT_HART_4 186
> -
> -#endif /* _DT_BINDINGS_INTERRUPT_CONTROLLER_MICROCHIP_MPFS_PLIC_H */
> diff --git a/include/dt-bindings/interrupt-controller/riscv-hart.h
> b/include/dt-bindings/interrupt-controller/riscv-hart.h
> deleted file mode 100644
> index c4331b8521..0000000000
> --- a/include/dt-bindings/interrupt-controller/riscv-hart.h
> +++ /dev/null
> @@ -1,17 +0,0 @@
> -/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
> -/* Copyright (c) 2020-2021 Microchip Technology Inc */
> -
> -#ifndef _DT_BINDINGS_INTERRUPT_CONTROLLER_RISCV_HART_H
> -#define _DT_BINDINGS_INTERRUPT_CONTROLLER_RISCV_HART_H
> -
> -#define HART_INT_U_SOFT 0
> -#define HART_INT_S_SOFT 1
> -#define HART_INT_M_SOFT 3
> -#define HART_INT_U_TIMER 4
> -#define HART_INT_S_TIMER 5
> -#define HART_INT_M_TIMER 7
> -#define HART_INT_U_EXT 8
> -#define HART_INT_S_EXT 9
> -#define HART_INT_M_EXT 11
> -
> -#endif /* _DT_BINDINGS_INTERRUPT_CONTROLLER_RISCV_HART_H */
More information about the U-Boot
mailing list