[PATCH 4/7] tools: mkeficapsule: Add support for parsing capsule params from config file
Takahiro Akashi
takahiro.akashi at linaro.org
Fri Jun 16 07:18:02 CEST 2023
On Fri, Jun 16, 2023 at 10:37:01AM +0530, Sughosh Ganu wrote:
> hi Takahiro,
>
> On Fri, 16 Jun 2023 at 10:16, Takahiro Akashi
> <takahiro.akashi at linaro.org> wrote:
> >
> > Hi Sughosh,
> >
> > On Fri, Jun 16, 2023 at 09:56:33AM +0530, Sughosh Ganu wrote:
> > > On Thu, 15 Jun 2023 at 11:19, Takahiro Akashi
> > > <takahiro.akashi at linaro.org> wrote:
> > > >
> > > > On Thu, Jun 15, 2023 at 10:09:06AM +0530, Sughosh Ganu wrote:
> > > > > On Wed, 14 Jun 2023 at 11:23, Takahiro Akashi
> > > > > <takahiro.akashi at linaro.org> wrote:
> > > > > >
> > > > > > On Wed, Jun 14, 2023 at 10:56:23AM +0530, Sughosh Ganu wrote:
> > > > > > > hi Takahiro,
> > > > > > >
> > > > > > > On Wed, 14 Jun 2023 at 09:09, Takahiro Akashi
> > > > > > > <takahiro.akashi at linaro.org> wrote:
> > > > > > > >
> > > > > > > > Hi Sughosh,
> > > > > > > >
> > > > > > > > I think this is a good extension to mkeficapsule, but
> > > > > > > >
> > > > > > > > On Tue, Jun 13, 2023 at 04:08:03PM +0530, Sughosh Ganu wrote:
> > > > > > > > > Add support for specifying the parameters needed for capsule
> > > > > > > > > generation through a config file, instead of passing them through
> > > > > > > > > command-line. Parameters for more than a single capsule file can be
> > > > > > > > > specified, resulting in generation of multiple capsules through a
> > > > > > > > > single invocation of the command.
> > > > > > > > >
> > > > > > > > > This path is to be used for generating capsules through a make target,
> > > > > > > > > with the parameters being parsed from the config file.
> > > > > > > > >
> > > > > > > > > Signed-off-by: Sughosh Ganu <sughosh.ganu at linaro.org>
> > > > > > > > > ---
> > > > > > > > > tools/Kconfig | 9 +
> > > > > > > > > tools/Makefile | 1 +
> > > > > > > > > tools/eficapsule.h | 110 ++++++++++++
> > > > > > > > > tools/mkeficapsule.c | 106 +++++++-----
> > > > > > > > > tools/mkeficapsule_parse.c | 345 +++++++++++++++++++++++++++++++++++++
> > > > > > > > > 5 files changed, 531 insertions(+), 40 deletions(-)
> > > > > > > > > create mode 100644 tools/mkeficapsule_parse.c
> > > > > > > > >
> > > > > > > > > diff --git a/tools/Kconfig b/tools/Kconfig
> > > > > > > > > index 539708f277..95f27b7c45 100644
> > > > > > > > > --- a/tools/Kconfig
> > > > > > > > > +++ b/tools/Kconfig
> > > > > > > > > @@ -98,6 +98,15 @@ config TOOLS_MKEFICAPSULE
> > > > > > > > > optionally sign that file. If you want to enable UEFI capsule
> > > > > > > > > update feature on your target, you certainly need this.
> > > > > > > > >
> > > > > > > > > +config EFI_CAPSULE_CFG_FILE
> > > > > > > > > + string "Path to the EFI Capsule Config File"
> > > > > > > > > + default ""
> > > > > > > > > + help
> > > > > > > > > + Path to the EFI capsule config file which provides the
> > > > > > > > > + parameters needed to build capsule(s). Parameters can be
> > > > > > > > > + provided for multiple payloads resulting in corresponding
> > > > > > > > > + capsule images being generated.
> > > > > > > > > +
> > > > > > > > > menuconfig FSPI_CONF_HEADER
> > > > > > > > > bool "FlexSPI Header Configuration"
> > > > > > > > > help
> > > > > > > > > diff --git a/tools/Makefile b/tools/Makefile
> > > > > > > > > index d793cf3bec..ef366f3d61 100644
> > > > > > > > > --- a/tools/Makefile
> > > > > > > > > +++ b/tools/Makefile
> > > > > > > > > @@ -250,6 +250,7 @@ HOSTLDLIBS_mkeficapsule += \
> > > > > > > > > HOSTLDLIBS_mkeficapsule += \
> > > > > > > > > $(shell pkg-config --libs uuid 2> /dev/null || echo "-luuid")
> > > > > > > > > hostprogs-$(CONFIG_TOOLS_MKEFICAPSULE) += mkeficapsule
> > > > > > > > > +mkeficapsule-objs := mkeficapsule.o mkeficapsule_parse.o
> > > > > > > > >
> > > > > > > > > # We build some files with extra pedantic flags to try to minimize things
> > > > > > > > > # that won't build on some weird host compiler -- though there are lots of
> > > > > > > > > diff --git a/tools/eficapsule.h b/tools/eficapsule.h
> > > > > > > > > index 072a4b5598..42e66c6d6a 100644
> > > > > > > > > --- a/tools/eficapsule.h
> > > > > > > > > +++ b/tools/eficapsule.h
> > > > > > > > > @@ -52,6 +52,38 @@ typedef struct {
> > > > > > > > > /* flags */
> > > > > > > > > #define CAPSULE_FLAGS_PERSIST_ACROSS_RESET 0x00010000
> > > > > > > > >
> > > > > > > > > +enum capsule_type {
> > > > > > > > > + CAPSULE_NORMAL_BLOB = 0,
> > > > > > > > > + CAPSULE_ACCEPT,
> > > > > > > > > + CAPSULE_REVERT,
> > > > > > > > > +};
> > > > > > > > > +
> > > > > > > > > +/**
> > > > > > > > > + * struct efi_capsule_params - Capsule parameters
> > > > > > > > > + * @image_guid: Guid value of the payload input image
> > > > > > > > > + * @image_index: Image index value
> > > > > > > > > + * @hardware_instance: Hardware instance to be used for the image
> > > > > > > > > + * @monotonic_count: Monotonic count value to be used for signed capsule
> > > > > > > > > + * @privkey_file: Path to private key used in capsule signing
> > > > > > > > > + * @cert_file: Path to public key certificate used in capsule signing
> > > > > > > > > + * @input_file: Path to payload input image
> > > > > > > > > + * @capsule_file: Path to the output capsule file
> > > > > > > > > + * @oemflags: Oemflags to be populated in the capsule header
> > > > > > > > > + * @capsule: Capsule Type, normal or accept or revert
> > > > > > > > > + */
> > > > > > > > > +struct efi_capsule_params {
> > > > > > > > > + efi_guid_t *image_guid;
> > > > > > > > > + unsigned long image_index;
> > > > > > > > > + unsigned long hardware_instance;
> > > > > > > > > + uint64_t monotonic_count;
> > > > > > > > > + char *privkey_file;
> > > > > > > > > + char *cert_file;
> > > > > > > > > + char *input_file;
> > > > > > > > > + char *capsule_file;
> > > > > > > > > + unsigned long oemflags;
> > > > > > > > > + enum capsule_type capsule;
> > > > > > > > > +};
> > > > > > > > > +
> > > > > > > > > struct efi_capsule_header {
> > > > > > > > > efi_guid_t capsule_guid;
> > > > > > > > > uint32_t header_size;
> > > > > > > > > @@ -113,4 +145,82 @@ struct efi_firmware_image_authentication {
> > > > > > > > > struct win_certificate_uefi_guid auth_info;
> > > > > > > > > } __packed;
> > > > > > > > >
> > > > > > > > > +/**
> > > > > > > > > + * capsule_with_cfg_file() - Generate capsule from config file
> > > > > > > > > + * @cfg_file: Path to the config file
> > > > > > > > > + *
> > > > > > > > > + * Parse the capsule parameters from the config file and use the
> > > > > > > > > + * parameters for generating one or more capsules.
> > > > > > > > > + *
> > > > > > > > > + * Return: None
> > > > > > > > > + *
> > > > > > > > > + */
> > > > > > > > > +void capsule_with_cfg_file(const char *cfg_file);
> > > > > > > > > +
> > > > > > > > > +/**
> > > > > > > > > + * convert_uuid_to_guid() - convert UUID to GUID
> > > > > > > > > + * @buf: UUID binary
> > > > > > > > > + *
> > > > > > > > > + * UUID and GUID have the same data structure, but their binary
> > > > > > > > > + * formats are different due to the endianness. See lib/uuid.c.
> > > > > > > > > + * Since uuid_parse() can handle only UUID, this function must
> > > > > > > > > + * be called to get correct data for GUID when parsing a string.
> > > > > > > > > + *
> > > > > > > > > + * The correct data will be returned in @buf.
> > > > > > > > > + */
> > > > > > > > > +void convert_uuid_to_guid(unsigned char *buf);
> > > > > > > > > +
> > > > > > > > > +/**
> > > > > > > > > + * create_empty_capsule() - Generate an empty capsule
> > > > > > > > > + * @path: Path to the empty capsule file to be generated
> > > > > > > > > + * @guid: Guid value of the image for which empty capsule is generated
> > > > > > > > > + * @fw_accept: Flag to specify whether to generate accept or revert capsule
> > > > > > > > > + *
> > > > > > > > > + * Generate an empty capsule, either an accept or a revert capsule to be
> > > > > > > > > + * used to flag acceptance or rejection of an earlier executed firmware
> > > > > > > > > + * update operation. Being used in the FWU Multi Bank firmware update
> > > > > > > > > + * feature.
> > > > > > > > > + *
> > > > > > > > > + * Return: 0 if OK, -ve on error
> > > > > > > > > + *
> > > > > > > > > + */
> > > > > > > > > +int create_empty_capsule(char *path, efi_guid_t *guid, bool fw_accept);
> > > > > > > > > +
> > > > > > > > > +/**
> > > > > > > > > + * create_fwbin - create an uefi capsule file
> > > > > > > > > + * @path: Path to a created capsule file
> > > > > > > > > + * @bin: Path to a firmware binary to encapsulate
> > > > > > > > > + * @guid: GUID of related FMP driver
> > > > > > > > > + * @index: Index number in capsule
> > > > > > > > > + * @instance: Instance number in capsule
> > > > > > > > > + * @mcount: Monotonic count in authentication information
> > > > > > > > > + * @private_file: Path to a private key file
> > > > > > > > > + * @cert_file: Path to a certificate file
> > > > > > > > > + * @oemflags: Capsule OEM Flags, bits 0-15
> > > > > > > > > + *
> > > > > > > > > + * This function actually does the job of creating an uefi capsule file.
> > > > > > > > > + * All the arguments must be supplied.
> > > > > > > > > + * If either @private_file ror @cert_file is NULL, the capsule file
> > > > > > > > > + * won't be signed.
> > > > > > > > > + *
> > > > > > > > > + * Return:
> > > > > > > > > + * * 0 - on success
> > > > > > > > > + * * -1 - on failure
> > > > > > > > > + */
> > > > > > > > > +int create_fwbin(char *path, char *bin, efi_guid_t *guid,
> > > > > > > > > + unsigned long index, unsigned long instance,
> > > > > > > > > + uint64_t mcount, char *privkey_file, char *cert_file,
> > > > > > > > > + uint16_t oemflags);
> > > > > > > > > +
> > > > > > > > > +/**
> > > > > > > > > + * print_usage() - Print the command usage string
> > > > > > > > > + *
> > > > > > > > > + * Prints the standard command usage string. Called in the case
> > > > > > > > > + * of incorrect parameters being passed to the tool.
> > > > > > > > > + *
> > > > > > > > > + * Return: None
> > > > > > > > > + *
> > > > > > > > > + */
> > > > > > > > > +void print_usage(void);
> > > > > > > > > +
> > > > > > > > > #endif /* _EFI_CAPSULE_H */
> > > > > > > > > diff --git a/tools/mkeficapsule.c b/tools/mkeficapsule.c
> > > > > > > > > index b71537beee..711adf0439 100644
> > > > > > > > > --- a/tools/mkeficapsule.c
> > > > > > > > > +++ b/tools/mkeficapsule.c
> > > > > > > > > @@ -31,12 +31,6 @@ efi_guid_t efi_guid_cert_type_pkcs7 = EFI_CERT_TYPE_PKCS7_GUID;
> > > > > > > > >
> > > > > > > > > static const char *opts_short = "g:i:I:v:p:c:m:o:dhAR";
> > > > > > > > >
> > > > > > > > > -enum {
> > > > > > > > > - CAPSULE_NORMAL_BLOB = 0,
> > > > > > > > > - CAPSULE_ACCEPT,
> > > > > > > > > - CAPSULE_REVERT,
> > > > > > > > > -} capsule_type;
> > > > > > > > > -
> > > > > > > > > static struct option options[] = {
> > > > > > > > > {"guid", required_argument, NULL, 'g'},
> > > > > > > > > {"index", required_argument, NULL, 'i'},
> > > > > > > > > @@ -52,7 +46,16 @@ static struct option options[] = {
> > > > > > > > > {NULL, 0, NULL, 0},
> > > > > > > > > };
> > > > > > > > >
> > > > > > > > > -static void print_usage(void)
> > > > > > > > > +/**
> > > > > > > > > + * print_usage() - Print the command usage string
> > > > > > > > > + *
> > > > > > > > > + * Prints the standard command usage string. Called in the case
> > > > > > > > > + * of incorrect parameters being passed to the tool.
> > > > > > > > > + *
> > > > > > > > > + * Return: None
> > > > > > > > > + *
> > > > > > > > > + */
> > > > > > > > > +void print_usage(void)
> > > > > > > > > {
> > > > > > > > > fprintf(stderr, "Usage: %s [options] <image blob> <output file>\n"
> > > > > > > > > "Options:\n"
> > > > > > > > > @@ -400,10 +403,10 @@ static void free_sig_data(struct auth_context *ctx)
> > > > > > > > > * * 0 - on success
> > > > > > > > > * * -1 - on failure
> > > > > > > > > */
> > > > > > > > > -static int create_fwbin(char *path, char *bin, efi_guid_t *guid,
> > > > > > > > > - unsigned long index, unsigned long instance,
> > > > > > > > > - uint64_t mcount, char *privkey_file, char *cert_file,
> > > > > > > > > - uint16_t oemflags)
> > > > > > > > > +int create_fwbin(char *path, char *bin, efi_guid_t *guid,
> > > > > > > > > + unsigned long index, unsigned long instance,
> > > > > > > > > + uint64_t mcount, char *privkey_file, char *cert_file,
> > > > > > > > > + uint16_t oemflags)
> > > > > > > > > {
> > > > > > > > > struct efi_capsule_header header;
> > > > > > > > > struct efi_firmware_management_capsule_header capsule;
> > > > > > > > > @@ -580,7 +583,21 @@ void convert_uuid_to_guid(unsigned char *buf)
> > > > > > > > > buf[7] = c;
> > > > > > > > > }
> > > > > > > > >
> > > > > > > > > -static int create_empty_capsule(char *path, efi_guid_t *guid, bool fw_accept)
> > > > > > > > > +/**
> > > > > > > > > + * create_empty_capsule() - Generate an empty capsule
> > > > > > > > > + * @path: Path to the empty capsule file to be generated
> > > > > > > > > + * @guid: Guid value of the image for which empty capsule is generated
> > > > > > > > > + * @fw_accept: Flag to specify whether to generate accept or revert capsule
> > > > > > > > > + *
> > > > > > > > > + * Generate an empty capsule, either an accept or a revert capsule to be
> > > > > > > > > + * used to flag acceptance or rejection of an earlier executed firmware
> > > > > > > > > + * update operation. Being used in the FWU Multi Bank firmware update
> > > > > > > > > + * feature.
> > > > > > > > > + *
> > > > > > > > > + * Return: 0 if OK, -ve on error
> > > > > > > > > + *
> > > > > > > > > + */
> > > > > > > > > +int create_empty_capsule(char *path, efi_guid_t *guid, bool fw_accept)
> > > > > > > > > {
> > > > > > > > > struct efi_capsule_header header = { 0 };
> > > > > > > > > FILE *f = NULL;
> > > > > > > > > @@ -623,19 +640,7 @@ err:
> > > > > > > > > return ret;
> > > > > > > > > }
> > > > > > > > >
> > > > > > > > > -/**
> > > > > > > > > - * main - main entry function of mkeficapsule
> > > > > > > > > - * @argc: Number of arguments
> > > > > > > > > - * @argv: Array of pointers to arguments
> > > > > > > > > - *
> > > > > > > > > - * Create an uefi capsule file, optionally signing it.
> > > > > > > > > - * Parse all the arguments and pass them on to create_fwbin().
> > > > > > > > > - *
> > > > > > > > > - * Return:
> > > > > > > > > - * * 0 - on success
> > > > > > > > > - * * -1 - on failure
> > > > > > > > > - */
> > > > > > > > > -int main(int argc, char **argv)
> > > > > > > > > +static void capsule_with_cmdline_params(int argc, char **argv)
> > > > > > > > > {
> > > > > > > > > efi_guid_t *guid;
> > > > > > > > > unsigned char uuid_buf[16];
> > > > > > > > > @@ -643,6 +648,7 @@ int main(int argc, char **argv)
> > > > > > > > > uint64_t mcount;
> > > > > > > > > unsigned long oemflags;
> > > > > > > > > char *privkey_file, *cert_file;
> > > > > > > > > + enum capsule_type capsule;
> > > > > > > > > int c, idx;
> > > > > > > > >
> > > > > > > > > guid = NULL;
> > > > > > > > > @@ -652,7 +658,7 @@ int main(int argc, char **argv)
> > > > > > > > > privkey_file = NULL;
> > > > > > > > > cert_file = NULL;
> > > > > > > > > dump_sig = 0;
> > > > > > > > > - capsule_type = CAPSULE_NORMAL_BLOB;
> > > > > > > > > + capsule = CAPSULE_NORMAL_BLOB;
> > > > > > > > > oemflags = 0;
> > > > > > > > > for (;;) {
> > > > > > > > > c = getopt_long(argc, argv, opts_short, options, &idx);
> > > > > > > > > @@ -702,20 +708,20 @@ int main(int argc, char **argv)
> > > > > > > > > dump_sig = 1;
> > > > > > > > > break;
> > > > > > > > > case 'A':
> > > > > > > > > - if (capsule_type) {
> > > > > > > > > + if (capsule) {
> > > > > > > > > fprintf(stderr,
> > > > > > > > > "Select either of Accept or Revert capsule generation\n");
> > > > > > > > > exit(1);
> > > > > > > > > }
> > > > > > > > > - capsule_type = CAPSULE_ACCEPT;
> > > > > > > > > + capsule = CAPSULE_ACCEPT;
> > > > > > > > > break;
> > > > > > > > > case 'R':
> > > > > > > > > - if (capsule_type) {
> > > > > > > > > + if (capsule) {
> > > > > > > > > fprintf(stderr,
> > > > > > > > > "Select either of Accept or Revert capsule generation\n");
> > > > > > > > > exit(1);
> > > > > > > > > }
> > > > > > > > > - capsule_type = CAPSULE_REVERT;
> > > > > > > > > + capsule = CAPSULE_REVERT;
> > > > > > > > > break;
> > > > > > > > > case 'o':
> > > > > > > > > oemflags = strtoul(optarg, NULL, 0);
> > > > > > > > > @@ -732,21 +738,21 @@ int main(int argc, char **argv)
> > > > > > > > > }
> > > > > > > > >
> > > > > > > > > /* check necessary parameters */
> > > > > > > > > - if ((capsule_type == CAPSULE_NORMAL_BLOB &&
> > > > > > > > > - ((argc != optind + 2) || !guid ||
> > > > > > > > > - ((privkey_file && !cert_file) ||
> > > > > > > > > - (!privkey_file && cert_file)))) ||
> > > > > > > > > - (capsule_type != CAPSULE_NORMAL_BLOB &&
> > > > > > > > > - ((argc != optind + 1) ||
> > > > > > > > > - ((capsule_type == CAPSULE_ACCEPT) && !guid) ||
> > > > > > > > > - ((capsule_type == CAPSULE_REVERT) && guid)))) {
> > > > > > > > > + if ((capsule == CAPSULE_NORMAL_BLOB &&
> > > > > > > > > + ((argc != optind + 2) || !guid ||
> > > > > > > > > + ((privkey_file && !cert_file) ||
> > > > > > > > > + (!privkey_file && cert_file)))) ||
> > > > > > > > > + (capsule != CAPSULE_NORMAL_BLOB &&
> > > > > > > > > + ((argc != optind + 1) ||
> > > > > > > > > + (capsule == CAPSULE_ACCEPT && !guid) ||
> > > > > > > > > + (capsule == CAPSULE_REVERT && guid)))) {
> > > > > > > > > print_usage();
> > > > > > > > > exit(EXIT_FAILURE);
> > > > > > > > > }
> > > > > > > > >
> > > > > > > > > - if (capsule_type != CAPSULE_NORMAL_BLOB) {
> > > > > > > > > + if (capsule != CAPSULE_NORMAL_BLOB) {
> > > > > > > > > if (create_empty_capsule(argv[argc - 1], guid,
> > > > > > > > > - capsule_type == CAPSULE_ACCEPT) < 0) {
> > > > > > > > > + capsule == CAPSULE_ACCEPT) < 0) {
> > > > > > > > > fprintf(stderr, "Creating empty capsule failed\n");
> > > > > > > > > exit(EXIT_FAILURE);
> > > > > > > > > }
> > > > > > > > > @@ -756,6 +762,26 @@ int main(int argc, char **argv)
> > > > > > > > > fprintf(stderr, "Creating firmware capsule failed\n");
> > > > > > > > > exit(EXIT_FAILURE);
> > > > > > > > > }
> > > > > > > > > +}
> > > > > > > > > +
> > > > > > > > > +/**
> > > > > > > > > + * main - main entry function of mkeficapsule
> > > > > > > > > + * @argc: Number of arguments
> > > > > > > > > + * @argv: Array of pointers to arguments
> > > > > > > > > + *
> > > > > > > > > + * Create an uefi capsule file, optionally signing it.
> > > > > > > > > + * Parse all the arguments and pass them on to create_fwbin().
> > > > > > > > > + *
> > > > > > > > > + * Return:
> > > > > > > > > + * * 0 - on success
> > > > > > > > > + * * -1 - on failure
> > > > > > > > > + */
> > > > > > > > > +int main(int argc, char **argv)
> > > > > > > > > +{
> > > > > > > > > + if (!strcmp(CONFIG_EFI_CAPSULE_CFG_FILE, ""))
> > > > > > > > > + capsule_with_cmdline_params(argc, argv);
> > > > > > > > > + else
> > > > > > > > > + capsule_with_cfg_file(CONFIG_EFI_CAPSULE_CFG_FILE);
> > > > > > > >
> > > > > > > > I don't know where the macro, CONFIG_EFI_CAPSULE_CFG_FILE, comes from.
> > > > > > > > Anyhow, as a general rule, any host tool must be as generic as it should not
> > > > > > > > depend on a target's config.
> > > > > > > > (I was told so before.)
> > > > > > > >
> > > > > > > > So I would suggest that you add another command line, say "--config-file <file>",
> > > > > > > > to make the command generic.
> > > > > > >
> > > > > > > Yes, that would be something followed by most of the tools. The reason
> > > > > > > I did not add a command-line option for the confile file is because I
> > > > > > > want the capsule generation added as a make target. With the path to
> > > > > > > the config file specified through the Kconfig symbol, we can invoke
> > > > > > > 'make capsule', and it would build the capsules by parsing the
> > > > > > > parameters from the config file, taken from the Kconfig symbol. I know
> > > > > > > there are ways of specifying options when using a make command, but I
> > > > > > > don't think that is a clean way of doing things.
> > > > > >
> > > > > > Not sure, but in your [5/7],
> > > > > > cmd_mkeficapsule = $(objtree)/tools/mkeficapsule --config-file $(CONFIG_EFI_CAPSULE_CFG_FILE)
> > > > > >
> > > > > > Doesn't this change work?
> > > > >
> > > > > So, I tried the above suggested change. But trying to run a make
> > > > > 'target' does not work without the .config file being present.
> > > >
> > > > Not sure what you meant to say here.
> > > > Why don't you have .config when building U-Boot (or rather 'target')?
> > >
> > > Maybe I misunderstood your earlier comment, but I thought you were
> > > looking to build capsules without relying on a target config.
> >
> > Not exactly.
> > The basic requirement, I believe, is that the exact same binary (with
> > the same set of functionalities) should be generated for any host tool
> > whatever a target's config, including tools-only_defconfig, is.
>
> Okay. I think I now understand what you are looking for. However, I
> believe if you want the same binary for both scenarios, the only way
> might be to drop the make target to generate capsules, and do it
> through the --config-file command-line option.
Again not sure what you're trying to do.
> I will check if we can
> pass the config file as a parameter when building capsules as a
> target. I could not get it working when I tried it earlier though. If
> this is indeed not possible, do you have a strong opinion on having
> the same binary for both scenarios?
I have no reason why you can't.
If you see any failure, please give me more details about how
you are going to manage so that I can help you.
-Takahiro Akashi
> -sughosh
>
> >
> > Is it clear now?
> >
> > -Takahiro Akashi
> >
> > > Which I
> > > believe cannot be done for a make target.
> > >
> > > -sughosh
> > >
> > > >
> > > > -Takahiro Akashi
> > > >
> > > > > FWIW,
> > > > > the same is the case for building tools as well. I think that is the
> > > > > reason for the tools-only_defconfig.
> > > > >
> > > > > -sughosh
> > > > >
> > > > > >
> > > > > > -Takahiro Akashi
> > > > > >
> > > > > >
> > > > > > > Given the use case of
> > > > > > > a make target, I hope we can use the Kconfig symbol for specifying the
> > > > > > > config file path.
> > > > > > >
> > > > > > > -sughosh
> > > > > > >
> > > > > > > >
> > > > > > > > -Takahiro Akashi
> > > > > > > >
> > > > > > > >
> > > > > > > > >
> > > > > > > > > exit(EXIT_SUCCESS);
> > > > > > > > > }
> > > > > > > > > diff --git a/tools/mkeficapsule_parse.c b/tools/mkeficapsule_parse.c
> > > > > > > > > new file mode 100644
> > > > > > > > > index 0000000000..ef4f3f6705
> > > > > > > > > --- /dev/null
> > > > > > > > > +++ b/tools/mkeficapsule_parse.c
> > > > > > > > > @@ -0,0 +1,345 @@
> > > > > > > > > +// SPDX-License-Identifier: GPL-2.0
> > > > > > > > > +/*
> > > > > > > > > + * Copyright 2023 Linaro Limited
> > > > > > > > > + */
> > > > > > > > > +
> > > > > > > > > +/*
> > > > > > > > > + * The code in this file adds parsing ability to the mkeficapsule
> > > > > > > > > + * tool. This allows specifying parameters needed to build the capsule
> > > > > > > > > + * through the config file instead of specifying them on the command-line.
> > > > > > > > > + * Parameters can be specified for more than one payload, generating the
> > > > > > > > > + * corresponding capsule files.
> > > > > > > > > + *
> > > > > > > > > + * The parameters are specified in a "key:value" pair. All the parameters
> > > > > > > > > + * that are currently supported by the mkeficapsule tool can be specified
> > > > > > > > > + * in the config file.
> > > > > > > > > + *
> > > > > > > > > + * The example below shows four payloads. The first payload is an example
> > > > > > > > > + * of generating a signed capsule. The second payload is an example of
> > > > > > > > > + * generating an unsigned capsule. The third payload is an accept empty
> > > > > > > > > + * capsule, while the fourth payload is the revert empty capsule, used
> > > > > > > > > + * for the multi-bank firmware update feature.
> > > > > > > > > + *
> > > > > > > > > + * This functionality can be easily extended to generate a single capsule
> > > > > > > > > + * comprising multiple payloads.
> > > > > > > > > +
> > > > > > > > > + {
> > > > > > > > > + image-guid: 02f4d760-cfd5-43bd-8e2d-a42acb33c660
> > > > > > > > > + hardware-instance: 0
> > > > > > > > > + monotonic-count: 1
> > > > > > > > > + payload: u-boot.bin
> > > > > > > > > + image-index: 1
> > > > > > > > > + private-key: /path/to/priv/key
> > > > > > > > > + pub-key-cert: /path/to/pub/key
> > > > > > > > > + capsule: u-boot.capsule
> > > > > > > > > + }
> > > > > > > > > + {
> > > > > > > > > + image-guid: 4ce292da-1dd8-428d-a1c2-77743ef8b96e
> > > > > > > > > + hardware-instance: 0
> > > > > > > > > + payload: u-boot.itb
> > > > > > > > > + image-index: 2
> > > > > > > > > + oemflags: 0x8000
> > > > > > > > > + capsule: fit.capsule
> > > > > > > > > + }
> > > > > > > > > + {
> > > > > > > > > + capsule-type: accept
> > > > > > > > > + image-guid: 4ce292da-1dd8-428d-a1c2-77743ef8b96e
> > > > > > > > > + capsule: accept.capsule
> > > > > > > > > + }
> > > > > > > > > + {
> > > > > > > > > + capsule-type: revert
> > > > > > > > > + capsule: revert.capsule
> > > > > > > > > + }
> > > > > > > > > +*/
> > > > > > > > > +
> > > > > > > > > +#include <ctype.h>
> > > > > > > > > +#include <limits.h>
> > > > > > > > > +#include <stdio.h>
> > > > > > > > > +#include <stdlib.h>
> > > > > > > > > +#include <string.h>
> > > > > > > > > +
> > > > > > > > > +#include <uuid/uuid.h>
> > > > > > > > > +
> > > > > > > > > +#include "eficapsule.h"
> > > > > > > > > +
> > > > > > > > > +#define PARAMS_START "{"
> > > > > > > > > +#define PARAMS_END "}"
> > > > > > > > > +
> > > > > > > > > +#define PSTART 2
> > > > > > > > > +#define PEND 3
> > > > > > > > > +
> > > > > > > > > +#define MALLOC_FAIL_STR "Unable to allocate memory\n"
> > > > > > > > > +
> > > > > > > > > +#define ARRAY_SIZE(x) (sizeof(x) / sizeof((x)[0]))
> > > > > > > > > +
> > > > > > > > > +const char *capsule_params[] = {
> > > > > > > > > + "image-guid", "image-index", "private-key",
> > > > > > > > > + "pub-key-cert", "payload", "capsule",
> > > > > > > > > + "hardware-instance", "monotonic-count",
> > > > > > > > > + "capsule-type", "oemflags" };
> > > > > > > > > +
> > > > > > > > > +static unsigned char params_start;
> > > > > > > > > +static unsigned char params_end;
> > > > > > > > > +
> > > > > > > > > +static void print_and_exit(const char *str)
> > > > > > > > > +{
> > > > > > > > > + fprintf(stderr, "%s", str);
> > > > > > > > > + exit(EXIT_FAILURE);
> > > > > > > > > +}
> > > > > > > > > +
> > > > > > > > > +static int param_delim_checks(char *line, unsigned char *token)
> > > > > > > > > +{
> > > > > > > > > + if (!strcmp(line, PARAMS_START)) {
> > > > > > > > > + if (params_start || !params_end) {
> > > > > > > > > + fprintf(stderr, "Earlier params processing still in progress. ");
> > > > > > > > > + fprintf(stderr, "Can't start processing a new params.\n");
> > > > > > > > > + exit(EXIT_FAILURE);
> > > > > > > > > + } else {
> > > > > > > > > + params_start = 1;
> > > > > > > > > + params_end = 0;
> > > > > > > > > + *token = PSTART;
> > > > > > > > > + return 1;
> > > > > > > > > + }
> > > > > > > > > + } else if (!strcmp(line, PARAMS_END)) {
> > > > > > > > > + if (!params_start) {
> > > > > > > > > + fprintf(stderr, "Cannot put end braces without start braces. ");
> > > > > > > > > + fprintf(stderr, "Please check the documentation for reference config file syntax\n");
> > > > > > > > > + exit(EXIT_FAILURE);
> > > > > > > > > + } else {
> > > > > > > > > + params_start = 0;
> > > > > > > > > + params_end = 1;
> > > > > > > > > + *token = PEND;
> > > > > > > > > + return 1;
> > > > > > > > > + }
> > > > > > > > > + } else if (!params_start) {
> > > > > > > > > + fprintf(stderr, "Params should be passed within braces. ");
> > > > > > > > > + fprintf(stderr, "Please check the documentation for reference config file syntax\n");
> > > > > > > > > + exit(EXIT_FAILURE);
> > > > > > > > > + }
> > > > > > > > > +
> > > > > > > > > + return 0;
> > > > > > > > > +}
> > > > > > > > > +
> > > > > > > > > +static void add_guid(efi_guid_t **guid_param, char *guid)
> > > > > > > > > +{
> > > > > > > > > + unsigned char uuid_buf[16];
> > > > > > > > > +
> > > > > > > > > + *guid_param = malloc(sizeof(efi_guid_t));
> > > > > > > > > + if (!*guid_param)
> > > > > > > > > + print_and_exit(MALLOC_FAIL_STR);
> > > > > > > > > +
> > > > > > > > > + if (uuid_parse(guid, uuid_buf))
> > > > > > > > > + print_and_exit("Wrong guid format\n");
> > > > > > > > > +
> > > > > > > > > + convert_uuid_to_guid(uuid_buf);
> > > > > > > > > + memcpy(*guid_param, uuid_buf, sizeof(efi_guid_t));
> > > > > > > > > +}
> > > > > > > > > +
> > > > > > > > > +static void add_string(char **dst, char *val)
> > > > > > > > > +{
> > > > > > > > > + *dst = strdup(val);
> > > > > > > > > + if (!*dst)
> > > > > > > > > + print_and_exit(MALLOC_FAIL_STR);
> > > > > > > > > +}
> > > > > > > > > +
> > > > > > > > > +static void match_and_populate_param(char *key, char *val,
> > > > > > > > > + struct efi_capsule_params *param)
> > > > > > > > > +{
> > > > > > > > > + int i;
> > > > > > > > > +
> > > > > > > > > + for (i = 0; i < ARRAY_SIZE(capsule_params); i++) {
> > > > > > > > > + if (!strcmp(key, capsule_params[i])) {
> > > > > > > > > + switch (i) {
> > > > > > > > > + case 0:
> > > > > > > > > + add_guid(¶m->image_guid, val);
> > > > > > > > > + return;
> > > > > > > > > + case 1:
> > > > > > > > > + param->image_index = strtoul(val, NULL, 0);
> > > > > > > > > + if (param->image_index == ULONG_MAX)
> > > > > > > > > + print_and_exit("Enter a valid value of index bewtween 1-255");
> > > > > > > > > + return;
> > > > > > > > > + case 2:
> > > > > > > > > + add_string(¶m->privkey_file, val);
> > > > > > > > > + return;
> > > > > > > > > + case 3:
> > > > > > > > > + add_string(¶m->cert_file, val);
> > > > > > > > > + return;
> > > > > > > > > + case 4:
> > > > > > > > > + add_string(¶m->input_file, val);
> > > > > > > > > + return;
> > > > > > > > > + case 5:
> > > > > > > > > + add_string(¶m->capsule_file, val);
> > > > > > > > > + return;
> > > > > > > > > + case 6:
> > > > > > > > > + param->hardware_instance = strtoul(val, NULL, 0);
> > > > > > > > > + if (param->hardware_instance == ULONG_MAX)
> > > > > > > > > + print_and_exit("Enter a valid hardware instance value");
> > > > > > > > > + return;
> > > > > > > > > + case 7:
> > > > > > > > > + param->monotonic_count = strtoull(val, NULL, 0);
> > > > > > > > > + if (param->monotonic_count == ULLONG_MAX)
> > > > > > > > > + print_and_exit("Enter a valid monotonic count value");
> > > > > > > > > + return;
> > > > > > > > > + case 8:
> > > > > > > > > + if (!strcmp(val, "normal"))
> > > > > > > > > + param->capsule = CAPSULE_NORMAL_BLOB;
> > > > > > > > > + else if (!strcmp(val, "accept"))
> > > > > > > > > + param->capsule = CAPSULE_ACCEPT;
> > > > > > > > > + else if (!strcmp(val, "revert"))
> > > > > > > > > + param->capsule = CAPSULE_REVERT;
> > > > > > > > > + else
> > > > > > > > > + print_and_exit("Invalid type of capsule");
> > > > > > > > > +
> > > > > > > > > + return;
> > > > > > > > > + case 9:
> > > > > > > > > + param->oemflags = strtoul(val, NULL, 0);
> > > > > > > > > + if (param->oemflags > 0xffff)
> > > > > > > > > + print_and_exit("OemFlags must be between 0x0 and 0xffff\n");
> > > > > > > > > + return;
> > > > > > > > > + }
> > > > > > > > > + }
> > > > > > > > > + }
> > > > > > > > > +
> > > > > > > > > + fprintf(stderr, "Undefined param %s specified. ", key);
> > > > > > > > > + fprintf(stderr, "Please check the documentation for reference config file syntax\n");
> > > > > > > > > + exit(EXIT_FAILURE);
> > > > > > > > > +}
> > > > > > > > > +
> > > > > > > > > +static int get_capsule_params(char *line, struct efi_capsule_params *params)
> > > > > > > > > +{
> > > > > > > > > + char *key = NULL;
> > > > > > > > > + char *val = NULL;
> > > > > > > > > + unsigned char token;
> > > > > > > > > +
> > > > > > > > > + if (param_delim_checks(line, &token))
> > > > > > > > > + return token;
> > > > > > > > > +
> > > > > > > > > + key = strtok(line, ":");
> > > > > > > > > + if (key)
> > > > > > > > > + val = strtok(NULL, "\0");
> > > > > > > > > + else
> > > > > > > > > + print_and_exit("Expect the params in a key:value pair\n");
> > > > > > > > > +
> > > > > > > > > + match_and_populate_param(key, val, params);
> > > > > > > > > +
> > > > > > > > > + return 0;
> > > > > > > > > +}
> > > > > > > > > +
> > > > > > > > > +static char *skip_whitespace(char *line)
> > > > > > > > > +{
> > > > > > > > > + char *ptr, *newline;
> > > > > > > > > +
> > > > > > > > > + ptr = malloc(strlen(line) + 1);
> > > > > > > > > + if (!ptr)
> > > > > > > > > + print_and_exit(MALLOC_FAIL_STR);
> > > > > > > > > +
> > > > > > > > > + for (newline = ptr; *line; line++)
> > > > > > > > > + if (!isblank(*line))
> > > > > > > > > + *ptr++ = *line;
> > > > > > > > > + *ptr = '\0';
> > > > > > > > > + return newline;
> > > > > > > > > +}
> > > > > > > > > +
> > > > > > > > > +static int parse_capsule_payload_params(FILE *fp, struct efi_capsule_params *params)
> > > > > > > > > +{
> > > > > > > > > + char *line = NULL;
> > > > > > > > > + char *newline;
> > > > > > > > > + size_t n = 0;
> > > > > > > > > + ssize_t len;
> > > > > > > > > +
> > > > > > > > > + while ((len = getline(&line, &n, fp)) != -1) {
> > > > > > > > > + if (len == 1 && line[len - 1] == '\n')
> > > > > > > > > + continue;
> > > > > > > > > +
> > > > > > > > > + line[len - 1] = '\0';
> > > > > > > > > +
> > > > > > > > > + newline = skip_whitespace(line);
> > > > > > > > > +
> > > > > > > > > + if (newline[0] == '#')
> > > > > > > > > + continue;
> > > > > > > > > +
> > > > > > > > > + if (get_capsule_params(newline, params) == PEND)
> > > > > > > > > + return 0;
> > > > > > > > > + }
> > > > > > > > > +
> > > > > > > > > + if (errno == EINVAL || errno == ENOMEM) {
> > > > > > > > > + fprintf(stderr, "getline() returned an error %s reading the line\n",
> > > > > > > > > + strerror(errno));
> > > > > > > > > + exit(EXIT_FAILURE);
> > > > > > > > > + } else if (params_start == 1 || params_end == 0) {
> > > > > > > > > + fprintf(stderr, "Params should be passed within braces. ");
> > > > > > > > > + fprintf(stderr, "Please check the documentation for reference config file syntax\n");
> > > > > > > > > + exit(EXIT_FAILURE);
> > > > > > > > > + } else {
> > > > > > > > > + return -1;
> > > > > > > > > + }
> > > > > > > > > +}
> > > > > > > > > +
> > > > > > > > > +static void params_dependency_check(struct efi_capsule_params *params)
> > > > > > > > > +{
> > > > > > > > > + /* check necessary parameters */
> > > > > > > > > + if ((params->capsule == CAPSULE_NORMAL_BLOB &&
> > > > > > > > > + ((!params->input_file || !params->capsule_file ||
> > > > > > > > > + !params->image_guid) ||
> > > > > > > > > + ((params->privkey_file && !params->cert_file) ||
> > > > > > > > > + (!params->privkey_file && params->cert_file)))) ||
> > > > > > > > > + (params->capsule != CAPSULE_NORMAL_BLOB &&
> > > > > > > > > + (!params->capsule_file ||
> > > > > > > > > + (params->capsule == CAPSULE_ACCEPT && !params->image_guid) ||
> > > > > > > > > + (params->capsule == CAPSULE_REVERT && params->image_guid)))) {
> > > > > > > > > + print_usage();
> > > > > > > > > + exit(EXIT_FAILURE);
> > > > > > > > > + }
> > > > > > > > > +}
> > > > > > > > > +
> > > > > > > > > +static void generate_capsule(struct efi_capsule_params *params)
> > > > > > > > > +{
> > > > > > > > > + if (params->capsule != CAPSULE_NORMAL_BLOB) {
> > > > > > > > > + if (create_empty_capsule(params->capsule_file,
> > > > > > > > > + params->image_guid,
> > > > > > > > > + params->capsule ==
> > > > > > > > > + CAPSULE_ACCEPT) < 0)
> > > > > > > > > + print_and_exit("Creating empty capsule failed\n");
> > > > > > > > > + } else if (create_fwbin(params->capsule_file, params->input_file,
> > > > > > > > > + params->image_guid, params->image_index,
> > > > > > > > > + params->hardware_instance,
> > > > > > > > > + params->monotonic_count,
> > > > > > > > > + params->privkey_file,
> > > > > > > > > + params->cert_file,
> > > > > > > > > + (uint16_t)params->oemflags) < 0) {
> > > > > > > > > + print_and_exit("Creating firmware capsule failed\n");
> > > > > > > > > + }
> > > > > > > > > +}
> > > > > > > > > +
> > > > > > > > > +/**
> > > > > > > > > + * capsule_with_cfg_file() - Generate capsule from config file
> > > > > > > > > + * @cfg_file: Path to the config file
> > > > > > > > > + *
> > > > > > > > > + * Parse the capsule parameters from the config file and use the
> > > > > > > > > + * parameters for generating one or more capsules.
> > > > > > > > > + *
> > > > > > > > > + * Return: None
> > > > > > > > > + *
> > > > > > > > > + */
> > > > > > > > > +void capsule_with_cfg_file(const char *cfg_file)
> > > > > > > > > +{
> > > > > > > > > + FILE *fp;
> > > > > > > > > + struct efi_capsule_params params = { 0 };
> > > > > > > > > +
> > > > > > > > > + fp = fopen(cfg_file, "r");
> > > > > > > > > + if (!fp) {
> > > > > > > > > + fprintf(stderr, "Unable to open the capsule config file %s\n",
> > > > > > > > > + cfg_file);
> > > > > > > > > + exit(EXIT_FAILURE);
> > > > > > > > > + }
> > > > > > > > > +
> > > > > > > > > + params_start = 0;
> > > > > > > > > + params_end = 1;
> > > > > > > > > +
> > > > > > > > > + while (parse_capsule_payload_params(fp, ¶ms) != -1) {
> > > > > > > > > + params_dependency_check(¶ms);
> > > > > > > > > + generate_capsule(¶ms);
> > > > > > > > > +
> > > > > > > > > + memset(¶ms, 0, sizeof(struct efi_capsule_params));
> > > > > > > > > + }
> > > > > > > > > +}
> > > > > > > > > --
> > > > > > > > > 2.34.1
> > > > > > > > >
More information about the U-Boot
mailing list