[PATCH v4 08/14] net: dwc_eth_qos: Add i.MX8M Plus RMII support

[Marek Vasut]

With DM clock support in place, it is easy to add RMII support into the
MAC driver. The RMII cannot operate at 1000 Mbps and at 100 and 10 Mbps
the clock frequency is 50 MHz and 5 MHz instead of 25 MHz and 2.5 MHz.

The board DT requires the following adjustments to EQoS node:
  phy-mode = "rmii";
  assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>,
  			<&clk IMX8MP_SYS_PLL2_100M>,
  			<&clk IMX8MP_SYS_PLL2_50M>;
  assigned-clock-rates = <0>, <100000000>, <50000000>;

Reviewed-by: Ramon Fried <rfried.dev at gmail.com>
Signed-off-by: Marek Vasut <marex at denx.de>
---
Cc: "Ariel D'Alessandro" <ariel.dalessandro at collabora.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx at nxp.com>
Cc: Andrey Zhizhikin <andrey.zhizhikin at leica-geosystems.com>
Cc: Fabio Estevam <festevam at gmail.com>
Cc: Joe Hershberger <joe.hershberger at ni.com>
Cc: Lukasz Majewski <lukma at denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler at toradex.com>
Cc: Marek Vasut <marex at denx.de>
Cc: Michael Trimarchi <michael at amarulasolutions.com>
Cc: Peng Fan <peng.fan at nxp.com>
Cc: Ramon Fried <rfried.dev at gmail.com>
Cc: Sean Anderson <seanga2 at gmail.com>
Cc: Stefano Babic <sbabic at denx.de>
Cc: Tim Harvey <tharvey at gateworks.com>
Cc: Tommaso Merciai <tommaso.merciai at amarulasolutions.com>
Cc: u-boot at lists.denx.de
---
V2: Add RB from Ramon
V3: Handle RGMII_*ID variants
V4: No change
---
 drivers/net/dwc_eth_qos_imx.c | 29 ++++++++++++++++++-----------
 1 file changed, 18 insertions(+), 11 deletions(-)

diff --git a/drivers/net/dwc_eth_qos_imx.c b/drivers/net/dwc_eth_qos_imx.c
index f5f3f2099f0..962c5373243 100644
--- a/drivers/net/dwc_eth_qos_imx.c
+++ b/drivers/net/dwc_eth_qos_imx.c
@@ -179,21 +179,28 @@ static int eqos_set_tx_clk_speed_imx(struct udevice *dev)
 
 	debug("%s(dev=%p):\n", __func__, dev);
 
-	switch (eqos->phy->speed) {
-	case SPEED_1000:
-		rate = 125 * 1000 * 1000;
-		break;
-	case SPEED_100:
-		rate = 25 * 1000 * 1000;
-		break;
-	case SPEED_10:
-		rate = 2.5 * 1000 * 1000;
-		break;
-	default:
+	if (eqos->phy->interface == PHY_INTERFACE_MODE_RMII)
+		rate = 5000;	/* 5000 kHz = 5 MHz */
+	else
+		rate = 2500;	/* 2500 kHz = 2.5 MHz */
+
+	if (eqos->phy->speed == SPEED_1000 &&
+	    (eqos->phy->interface == PHY_INTERFACE_MODE_RGMII ||
+	     eqos->phy->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+	     eqos->phy->interface == PHY_INTERFACE_MODE_RGMII_RXID ||
+	     eqos->phy->interface == PHY_INTERFACE_MODE_RGMII_TXID)) {
+		rate *= 50;	/* Use 50x base rate i.e. 125 MHz */
+	} else if (eqos->phy->speed == SPEED_100) {
+		rate *= 10;	/* Use 10x base rate */
+	} else if (eqos->phy->speed == SPEED_10) {
+		rate *= 1;	/* Use base rate */
+	} else {
 		pr_err("invalid speed %d", eqos->phy->speed);
 		return -EINVAL;
 	}
 
+	rate *= 1000;	/* clk_set_rate() operates in Hz */
+
 	ret = clk_set_rate(&eqos->clk_tx, rate);
 	if (ret < 0) {
 		pr_err("imx (tx_clk, %lu) failed: %d", rate, ret);
-- 
2.39.2