[PATCH v4 06/10] dts: basic devicetree for Renesas RZ/N1 SoC

Ralph Siemsen ralph.siemsen at linaro.org
Wed Mar 8 21:26:49 CET 2023


This is taken from Linux kernel 5.17, and contains just bare minimum
functionality: CPU, UART and system timer.

Additional functionality (from newer kernel versions) will be added
later. Note that the Linux side is under active development.

Signed-off-by: Ralph Siemsen <ralph.siemsen at linaro.org>
---
The following changes were made, compared with Linux 5.17:

1) Add node for system controller registers.
   Declare it as syscon to provide a regmap interface.

2) In the clock controller node (renesas,r9a06g032-sysctrl),
   replace regs with regmap.

3) Add syscon-reset node, making use of the syscon regmap.

4) Add syscon phandle to ddrctrl. Used for checking h/w version.

5) Simplify the compatible string for all the UARTS, as per
   doc/device-tree-bindings/serial/snps-dw-apb-uart.txt

I could not find a way to avoid 1) and 2). Putting "syscon" in the
compatible string for the clock controller leads to a catch-22,
where the driver fails to initialize, and then boot hangs.

(no changes since v3)

Changes in v3:
- add syscon phandle to ddrctl
- simplify UART compatible strings

 arch/arm/dts/r9a06g032.dtsi                   | 226 ++++++++++++++++++
 include/dt-bindings/clock/r9a06g032-sysctrl.h | 148 ++++++++++++
 2 files changed, 374 insertions(+)
 create mode 100644 arch/arm/dts/r9a06g032.dtsi
 create mode 100644 include/dt-bindings/clock/r9a06g032-sysctrl.h

diff --git a/arch/arm/dts/r9a06g032.dtsi b/arch/arm/dts/r9a06g032.dtsi
new file mode 100644
index 0000000000..e0ddffb074
--- /dev/null
+++ b/arch/arm/dts/r9a06g032.dtsi
@@ -0,0 +1,226 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Base Device Tree Source for the Renesas RZ/N1D (R9A06G032)
+ *
+ * Copyright (C) 2018 Renesas Electronics Europe Limited
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/r9a06g032-sysctrl.h>
+
+/ {
+	compatible = "renesas,r9a06g032";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0>;
+			clocks = <&sysctrl R9A06G032_CLK_A7MP>;
+		};
+
+		cpu at 1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <1>;
+			clocks = <&sysctrl R9A06G032_CLK_A7MP>;
+			enable-method = "renesas,r9a06g032-smp";
+			cpu-release-addr = <0 0x4000c204>;
+		};
+	};
+
+	ext_jtag_clk: extjtagclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	ext_mclk: extmclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <40000000>;
+	};
+
+	ext_rgmii_ref: extrgmiiref {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	ext_rtc_clk: extrtcclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-parent = <&gic>;
+		ranges;
+
+		plat_regs: system-controller at 4000c000 {
+			compatible = "syscon";
+			reg = <0x4000c000 0x1000>;
+			u-boot,dm-pre-reloc;
+		};
+
+		sysctrl: clock {
+			compatible = "renesas,r9a06g032-sysctrl";
+			#clock-cells = <1>;
+			regmap = <&plat_regs>;
+			u-boot,dm-pre-reloc;
+
+			clocks = <&ext_mclk>, <&ext_rtc_clk>,
+					<&ext_jtag_clk>, <&ext_rgmii_ref>;
+			clock-names = "mclk", "rtc", "jtag", "rgmii_ref_ext";
+		};
+
+		ddrctrl: memory-controller at 4000d000 {
+			compatible = "cadence,ddr-ctrl";
+			reg = <0x4000d000 0x1000>, <0x4000e000 0x100>;
+			reg-names = "ddrc", "phy";
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sysctrl R9A06G032_CLK_DDRC>, <&sysctrl R9A06G032_HCLK_DDRC>;
+			clock-names = "clk_ddrc", "hclk_ddrc";
+			syscon = <&plat_regs>;
+			status = "disabled";
+		};
+
+		uart0: serial at 40060000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x40060000 0x400>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART0>, <&sysctrl R9A06G032_HCLK_UART0>;
+			clock-names = "baudclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart1: serial at 40061000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x40061000 0x400>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART1>, <&sysctrl R9A06G032_HCLK_UART1>;
+			clock-names = "baudclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart2: serial at 40062000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x40062000 0x400>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART2>, <&sysctrl R9A06G032_HCLK_UART2>;
+			clock-names = "baudclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart3: serial at 50000000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x50000000 0x400>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART3>, <&sysctrl R9A06G032_HCLK_UART3>;
+			clock-names = "baudclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart4: serial at 50001000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x50001000 0x400>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART4>, <&sysctrl R9A06G032_HCLK_UART4>;
+			clock-names = "baudclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart5: serial at 50002000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x50002000 0x400>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART5>, <&sysctrl R9A06G032_HCLK_UART5>;
+			clock-names = "baudclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart6: serial at 50003000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x50003000 0x400>;
+			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART6>, <&sysctrl R9A06G032_HCLK_UART6>;
+			clock-names = "baudclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart7: serial at 50004000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x50004000 0x400>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&sysctrl R9A06G032_CLK_UART7>, <&sysctrl R9A06G032_HCLK_UART7>;
+			clock-names = "baudclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		pinctrl: pinctrl at 40067000 {
+			compatible = "renesas,r9a06g032-pinctrl", "renesas,rzn1-pinctrl";
+			reg = <0x40067000 0x1000>, <0x51000000 0x480>;
+			clocks = <&sysctrl R9A06G032_HCLK_PINCONFIG>;
+			clock-names = "bus";
+			status = "disabled";
+		};
+
+		gic: interrupt-controller at 44101000 {
+			compatible = "arm,gic-400", "arm,cortex-a7-gic";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x44101000 0x1000>, /* Distributer */
+			      <0x44102000 0x2000>, /* CPU interface */
+			      <0x44104000 0x2000>, /* Virt interface control */
+			      <0x44106000 0x2000>; /* Virt CPU interface */
+			interrupts =
+				<GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+	};
+
+	timer {
+		compatible = "arm,cortex-a7-timer",
+			     "arm,armv7-timer";
+		interrupt-parent = <&gic>;
+		arm,cpu-registers-not-fw-configured;
+		always-on;
+		interrupts =
+			<GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	reboot {
+		compatible = "syscon-reboot";
+		regmap = <&plat_regs>;
+		offset = <0x198>;       /* sysctrl.RSTEN */
+		mask = <0x40>;          /* bit 6 = SWRST_REQ */
+		value = <0x40>;
+	};
+};
diff --git a/include/dt-bindings/clock/r9a06g032-sysctrl.h b/include/dt-bindings/clock/r9a06g032-sysctrl.h
new file mode 100644
index 0000000000..90c0f3dc1b
--- /dev/null
+++ b/include/dt-bindings/clock/r9a06g032-sysctrl.h
@@ -0,0 +1,148 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * R9A06G032 sysctrl IDs
+ *
+ * Copyright (C) 2018 Renesas Electronics Europe Limited
+ *
+ * Michel Pollet <michel.pollet at bp.renesas.com>, <buserror at gmail.com>
+ */
+
+#ifndef __DT_BINDINGS_R9A06G032_SYSCTRL_H__
+#define __DT_BINDINGS_R9A06G032_SYSCTRL_H__
+
+#define R9A06G032_CLK_PLL_USB		1
+#define R9A06G032_CLK_48		1	/* AKA CLK_PLL_USB */
+#define R9A06G032_MSEBIS_CLK		3	/* AKA CLKOUT_D16 */
+#define R9A06G032_MSEBIM_CLK		3	/* AKA CLKOUT_D16 */
+#define R9A06G032_CLK_DDRPHY_PLLCLK	5	/* AKA CLKOUT_D1OR2 */
+#define R9A06G032_CLK50			6	/* AKA CLKOUT_D20 */
+#define R9A06G032_CLK25			7	/* AKA CLKOUT_D40 */
+#define R9A06G032_CLK125		9	/* AKA CLKOUT_D8 */
+#define R9A06G032_CLK_P5_PG1		17	/* AKA DIV_P5_PG */
+#define R9A06G032_CLK_REF_SYNC		21	/* AKA DIV_REF_SYNC */
+#define R9A06G032_CLK_25_PG4		26
+#define R9A06G032_CLK_25_PG5		27
+#define R9A06G032_CLK_25_PG6		28
+#define R9A06G032_CLK_25_PG7		29
+#define R9A06G032_CLK_25_PG8		30
+#define R9A06G032_CLK_ADC		31
+#define R9A06G032_CLK_ECAT100		32
+#define R9A06G032_CLK_HSR100		33
+#define R9A06G032_CLK_I2C0		34
+#define R9A06G032_CLK_I2C1		35
+#define R9A06G032_CLK_MII_REF		36
+#define R9A06G032_CLK_NAND		37
+#define R9A06G032_CLK_NOUSBP2_PG6	38
+#define R9A06G032_CLK_P1_PG2		39
+#define R9A06G032_CLK_P1_PG3		40
+#define R9A06G032_CLK_P1_PG4		41
+#define R9A06G032_CLK_P4_PG3		42
+#define R9A06G032_CLK_P4_PG4		43
+#define R9A06G032_CLK_P6_PG1		44
+#define R9A06G032_CLK_P6_PG2		45
+#define R9A06G032_CLK_P6_PG3		46
+#define R9A06G032_CLK_P6_PG4		47
+#define R9A06G032_CLK_PCI_USB		48
+#define R9A06G032_CLK_QSPI0		49
+#define R9A06G032_CLK_QSPI1		50
+#define R9A06G032_CLK_RGMII_REF		51
+#define R9A06G032_CLK_RMII_REF		52
+#define R9A06G032_CLK_SDIO0		53
+#define R9A06G032_CLK_SDIO1		54
+#define R9A06G032_CLK_SERCOS100		55
+#define R9A06G032_CLK_SLCD		56
+#define R9A06G032_CLK_SPI0		57
+#define R9A06G032_CLK_SPI1		58
+#define R9A06G032_CLK_SPI2		59
+#define R9A06G032_CLK_SPI3		60
+#define R9A06G032_CLK_SPI4		61
+#define R9A06G032_CLK_SPI5		62
+#define R9A06G032_CLK_SWITCH		63
+#define R9A06G032_HCLK_ECAT125		65
+#define R9A06G032_HCLK_PINCONFIG	66
+#define R9A06G032_HCLK_SERCOS		67
+#define R9A06G032_HCLK_SGPIO2		68
+#define R9A06G032_HCLK_SGPIO3		69
+#define R9A06G032_HCLK_SGPIO4		70
+#define R9A06G032_HCLK_TIMER0		71
+#define R9A06G032_HCLK_TIMER1		72
+#define R9A06G032_HCLK_USBF		73
+#define R9A06G032_HCLK_USBH		74
+#define R9A06G032_HCLK_USBPM		75
+#define R9A06G032_CLK_48_PG_F		76
+#define R9A06G032_CLK_48_PG4		77
+#define R9A06G032_CLK_DDRPHY_PCLK	81	/* AKA CLK_REF_SYNC_D4 */
+#define R9A06G032_CLK_FW		81	/* AKA CLK_REF_SYNC_D4 */
+#define R9A06G032_CLK_CRYPTO		81	/* AKA CLK_REF_SYNC_D4 */
+#define R9A06G032_CLK_A7MP		84	/* AKA DIV_CA7 */
+#define R9A06G032_HCLK_CAN0		85
+#define R9A06G032_HCLK_CAN1		86
+#define R9A06G032_HCLK_DELTASIGMA	87
+#define R9A06G032_HCLK_PWMPTO		88
+#define R9A06G032_HCLK_RSV		89
+#define R9A06G032_HCLK_SGPIO0		90
+#define R9A06G032_HCLK_SGPIO1		91
+#define R9A06G032_RTOS_MDC		92
+#define R9A06G032_CLK_CM3		93
+#define R9A06G032_CLK_DDRC		94
+#define R9A06G032_CLK_ECAT25		95
+#define R9A06G032_CLK_HSR50		96
+#define R9A06G032_CLK_HW_RTOS		97
+#define R9A06G032_CLK_SERCOS50		98
+#define R9A06G032_HCLK_ADC		99
+#define R9A06G032_HCLK_CM3		100
+#define R9A06G032_HCLK_CRYPTO_EIP150	101
+#define R9A06G032_HCLK_CRYPTO_EIP93	102
+#define R9A06G032_HCLK_DDRC		103
+#define R9A06G032_HCLK_DMA0		104
+#define R9A06G032_HCLK_DMA1		105
+#define R9A06G032_HCLK_GMAC0		106
+#define R9A06G032_HCLK_GMAC1		107
+#define R9A06G032_HCLK_GPIO0		108
+#define R9A06G032_HCLK_GPIO1		109
+#define R9A06G032_HCLK_GPIO2		110
+#define R9A06G032_HCLK_HSR		111
+#define R9A06G032_HCLK_I2C0		112
+#define R9A06G032_HCLK_I2C1		113
+#define R9A06G032_HCLK_LCD		114
+#define R9A06G032_HCLK_MSEBI_M		115
+#define R9A06G032_HCLK_MSEBI_S		116
+#define R9A06G032_HCLK_NAND		117
+#define R9A06G032_HCLK_PG_I		118
+#define R9A06G032_HCLK_PG19		119
+#define R9A06G032_HCLK_PG20		120
+#define R9A06G032_HCLK_PG3		121
+#define R9A06G032_HCLK_PG4		122
+#define R9A06G032_HCLK_QSPI0		123
+#define R9A06G032_HCLK_QSPI1		124
+#define R9A06G032_HCLK_ROM		125
+#define R9A06G032_HCLK_RTC		126
+#define R9A06G032_HCLK_SDIO0		127
+#define R9A06G032_HCLK_SDIO1		128
+#define R9A06G032_HCLK_SEMAP		129
+#define R9A06G032_HCLK_SPI0		130
+#define R9A06G032_HCLK_SPI1		131
+#define R9A06G032_HCLK_SPI2		132
+#define R9A06G032_HCLK_SPI3		133
+#define R9A06G032_HCLK_SPI4		134
+#define R9A06G032_HCLK_SPI5		135
+#define R9A06G032_HCLK_SWITCH		136
+#define R9A06G032_HCLK_SWITCH_RG	137
+#define R9A06G032_HCLK_UART0		138
+#define R9A06G032_HCLK_UART1		139
+#define R9A06G032_HCLK_UART2		140
+#define R9A06G032_HCLK_UART3		141
+#define R9A06G032_HCLK_UART4		142
+#define R9A06G032_HCLK_UART5		143
+#define R9A06G032_HCLK_UART6		144
+#define R9A06G032_HCLK_UART7		145
+#define R9A06G032_CLK_UART0		146
+#define R9A06G032_CLK_UART1		147
+#define R9A06G032_CLK_UART2		148
+#define R9A06G032_CLK_UART3		149
+#define R9A06G032_CLK_UART4		150
+#define R9A06G032_CLK_UART5		151
+#define R9A06G032_CLK_UART6		152
+#define R9A06G032_CLK_UART7		153
+
+#endif /* __DT_BINDINGS_R9A06G032_SYSCTRL_H__ */
-- 
2.25.1



More information about the U-Boot mailing list