[PATCH RFC u-boot-mvebu 0/2] arm: mvebu: Fix eMMC boot
Martin Rowe
martin.p.rowe at gmail.com
Wed Mar 22 13:38:02 CET 2023
On Tue, 21 Mar 2023 at 08:08, Pali Rohár <pali at kernel.org> wrote:
> On Tuesday 21 March 2023 08:01:16 Martin Rowe wrote:
> > On Mon, 20 Mar 2023 at 17:33, Pali Rohár <pali at kernel.org> wrote:
> >
> > > On Monday 20 March 2023 11:48:59 Martin Rowe wrote:
> > > > On Sun, 19 Mar 2023 at 16:22, Pali Rohár <pali at kernel.org> wrote:
> > > >
> > > > > On Sunday 19 March 2023 00:32:01 Martin Rowe wrote:
> > > > > > On Mon, 6 Mar 2023 at 11:53, Pali Rohár <pali at kernel.org> wrote:
> > > > > >
> > > > > > > Could you try to print mmc->part_config (ideally as early as
> > > possible)?
> > > > > > >
> > > > > >
> > > > > > In SPL mmc->part_config is 255
> > > > > > In main u-boot at the start of clearfog.c board_init()
> > > mmc->part_config
> > > > > is
> > > > > > 255
> > > > > > In main u-boot at the start of clearfog.c checkboard()
> > > mmc->part_config
> > > > > is
> > > > > > 8 (ack: 0, partition_enable: 1, access: 0)
> > > > >
> > > > > 255 is uninitialized value.
> > > > >
> > > > > > If I set partition_enable to 2, I get the same result except the
> > > value is
> > > > > > 16 (ack: 0, partition_enable: 2, access: 0) instead of 8 for the
> > > last
> > > > > value
> > > > >
> > > > > Try to change "access" bits.
> > > > >
> > > > > > <partition_enable 1>
> > > > > > BootROM - 1.73
> > > > > >
> > > > > > Booting from MMC
> > > > > >
> > > > > > U-Boot SPL 2023.04-rc3-00159-gd1653548d2-dirty (Mar 19 2023 -
> > > 10:05:32
> > > > > > +1000)
> > > > > > High speed PHY - Version: 2.0
> > > > > > EEPROM TLV detection failed: Using static config for Clearfog
> Pro.
> > > > > > Detected Device ID 6828
> > > > > > board SerDes lanes topology details:
> > > > > > | Lane # | Speed | Type |
> > > > > > --------------------------------
> > > > > > | 0 | 3 | SATA0 |
> > > > > > | 1 | 0 | SGMII1 |
> > > > > > | 2 | 5 | PCIe1 |
> > > > > > | 3 | 5 | USB3 HOST1 |
> > > > > > | 4 | 5 | PCIe2 |
> > > > > > | 5 | 0 | SGMII2 |
> > > > > > --------------------------------
> > > > > > High speed PHY - Ended Successfully
> > > > > > mv_ddr: 14.0.0
> > > > > > DDR3 Training Sequence - Switching XBAR Window to FastPath Window
> > > > > > mv_ddr: completed successfully
> > > > > > spl.c spl_boot_device part_config = 255
> > > > > > Trying to boot from MMC1
> > > > > >
> > > > > >
> > > > > > U-Boot 2023.04-rc3-00159-gd1653548d2-dirty (Mar 19 2023 -
> 10:05:32
> > > +1000)
> > > > > >
> > > > > > SoC: MV88F6828-A0 at 1600 MHz
> > > > > > DRAM: 1 GiB (800 MHz, 32-bit, ECC not enabled)
> > > > > > clearfog.c board_init part_config = 255
> > > > > > Core: 38 devices, 22 uclasses, devicetree: separate
> > > > > > MMC: mv_sdh: 0
> > > > > > Loading Environment from MMC... *** Warning - bad CRC, using
> default
> > > > > > environment
> > > > > >
> > > > > > Model: SolidRun Clearfog A1
> > > > > > clearfog.c checkboard part_config = 8
> > > > > > Board: SolidRun Clearfog Pro
> > > > > > Net:
> > > > > > Warning: ethernet at 70000 (eth1) using random MAC address -
> > > > > 32:16:0e:b4:d1:d8
> > > > > > eth1: ethernet at 70000
> > > > > > Warning: ethernet at 30000 (eth2) using random MAC address -
> > > > > 72:30:3f:79:07:12
> > > > > > , eth2: ethernet at 30000
> > > > > > Warning: ethernet at 34000 (eth3) using random MAC address -
> > > > > 82:fb:71:23:46:4f
> > > > > > , eth3: ethernet at 34000
> > > > > > Hit any key to stop autoboot: 0
> > > > > > => mmc partconf 0
> > > > > > EXT_CSD[179], PARTITION_CONFIG:
> > > > > > BOOT_ACK: 0x0
> > > > > > BOOT_PARTITION_ENABLE: 0x1
> > > > > > PARTITION_ACCESS: 0x0
> > > > > > </partition_enable 1>
> > > > > >
> > > > > > <partition_enable 2>
> > > > > > BootROM - 1.73
> > > > > >
> > > > > > Booting from MMC
> > > > > >
> > > > > > U-Boot SPL 2023.04-rc3-00159-gd1653548d2-dirty (Mar 19 2023 -
> > > 10:05:32
> > > > > > +1000)
> > > > > > High speed PHY - Version: 2.0
> > > > > > EEPROM TLV detection failed: Using static config for Clearfog
> Pro.
> > > > > > Detected Device ID 6828
> > > > > > board SerDes lanes topology details:
> > > > > > | Lane # | Speed | Type |
> > > > > > --------------------------------
> > > > > > | 0 | 3 | SATA0 |
> > > > > > | 1 | 0 | SGMII1 |
> > > > > > | 2 | 5 | PCIe1 |
> > > > > > | 3 | 5 | USB3 HOST1 |
> > > > > > | 4 | 5 | PCIe2 |
> > > > > > | 5 | 0 | SGMII2 |
> > > > > > --------------------------------
> > > > > > High speed PHY - Ended Successfully
> > > > > > mv_ddr: 14.0.0
> > > > > > DDR3 Training Sequence - Switching XBAR Window to FastPath Window
> > > > > > mv_ddr: completed successfully
> > > > > > spl.c spl_boot_device part_config = 255
> > > > > > Trying to boot from MMC1
> > > > > >
> > > > > >
> > > > > > U-Boot 2023.04-rc3-00159-gd1653548d2-dirty (Mar 19 2023 -
> 10:05:32
> > > +1000)
> > > > > >
> > > > > > SoC: MV88F6828-A0 at 1600 MHz
> > > > > > DRAM: 1 GiB (800 MHz, 32-bit, ECC not enabled)
> > > > > > clearfog.c board_init part_config = 255
> > > > > > Core: 38 devices, 22 uclasses, devicetree: separate
> > > > > > MMC: mv_sdh: 0
> > > > > > Loading Environment from MMC... *** Warning - bad CRC, using
> default
> > > > > > environment
> > > > > >
> > > > > > Model: SolidRun Clearfog A1
> > > > > > clearfog.c checkboard part_config = 16
> > > > > > Board: SolidRun Clearfog Pro
> > > > > > Net:
> > > > > > Warning: ethernet at 70000 (eth1) using random MAC address -
> > > > > 92:5a:fc:14:e8:f6
> > > > > > eth1: ethernet at 70000
> > > > > > Warning: ethernet at 30000 (eth2) using random MAC address -
> > > > > 42:9c:d8:3a:cb:b2
> > > > > > , eth2: ethernet at 30000
> > > > > > Warning: ethernet at 34000 (eth3) using random MAC address -
> > > > > c6:99:20:f4:02:a0
> > > > > > , eth3: ethernet at 34000
> > > > > > Hit any key to stop autoboot: 0
> > > > > > => mmc partconf 0
> > > > > > EXT_CSD[179], PARTITION_CONFIG:
> > > > > > BOOT_ACK: 0x0
> > > > > > BOOT_PARTITION_ENABLE: 0x2
> > > > > > PARTITION_ACCESS: 0x0
> > > > > > </partition_enable 2>
> > > > >
> > > > > Are both logs from the configuration when SPL+u-boot is stored on
> > > Boot0?
> > > > > Could you try to erase Boot0 and store SPL+u-boot to Boot1? I'm
> > > > > interested to see if "access" bits are changed in SPL (before
> loading
> > > > > main u-boot).
> > > > >
> > > > > > I'm having trouble trying to find the hooks which run between
> > > board_init
> > > > > > and checkboard. If you can point me in the right direction I'm
> happy
> > > to
> > > > > > re-run and try to narrow down where the valid values are being
> set
> > > from.
> > > > >
> > > > > Print it directly in drivers/mmc/mmc.c mmc_startup_v4() where
> > > > > mmc->part_config = is set from ext_csd[EXT_CSD_PART_CONF] register.
> > > > > I want to see original value from EXT_CSD_PART_CONF.
> > > > >
> > > > > I do not know which hook is the best, so printing it from mmc.c
> driver
> > > > > should work better.
> > > > >
> > > >
> > > > u-boot in boot0, partconf set to 0x1:
> > > > mmc->part_config = 8
> > > >
> > > > u-boot in boot0, partconf set to 0x2:
> > > > mmc->part_config = 16
> > > >
> > > > u-boot in boot1 (boot0 zeroed), partconf set to 0x1:
> > > > mmc->part_config = 8
> > > >
> > > > u-boot in boot1 (boot0 zeroed), partconf set to 0x2:
> > > > mmc->part_config = 16
> > >
> > > Ah, that does not look useful :-(
> > >
> > > Just to confirm, is this output from SPL or from main U-Boot?
> > >
> >
> > Definitely SPL. I triple checked because I was also disappointed with
> those
> > results. With BootROM hardcoded with its boot order it seems like neither
> > CONFIG_SYS_MMCSD_RAW_MODE_EMMC_BOOT_PARTITION nor relying on
> > mmc->part_config is going to work well.
>
> In emmc spec is written:
>
> Each time the host wants to access a partition the following flow shall be
> executed:
> 1. Set PARTITION_ACCESS bits in the PARTITION_CONFIG field of the Extended
> CSD register in order to address one of the partitions
> 2. Issue commands referred to the selected partition
> 3. Restore default access to the User Data Area or re-direction the access
> to another partition
> All the reset events (CMD0 or hardware reset) will restore the access by
> default to the User Data Area.
>
> I'm feeling that partition_access bits should be preserved between
> reading data from boot0 and starting SPL. And these bits somehow could
> be used to determinate from which source bootrom loaded SPL. Maybe the
> last point ("all the reset events...") applies there and u-boot mmc
> driver does some reset in its init phase? And need to figure
> out how to read PARTITION_ACCESS without u-boot's mmc driver?
>
I enabled MMC tracing and added some printfs in mmc.c functions to see if
we can get a better idea of where best to read the value from:
<output>
BootROM - 1.73
Booting from MMC
U-Boot SPL 2023.04-rc4-00342-g7e562609bb-dirty (Mar 22 2023 - 22:14:28
+1000)
High speed PHY - Version: 2.0
EEPROM TLV detection failed: Using static config for Clearfog Pro.
Detected Device ID 6828
board SerDes lanes topology details:
| Lane # | Speed | Type |
--------------------------------
| 0 | 3 | SATA0 |
| 1 | 0 | SGMII1 |
| 2 | 5 | PCIe1 |
| 3 | 5 | USB3 HOST1 |
| 4 | 5 | PCIe2 |
| 5 | 0 | SGMII2 |
--------------------------------
High speed PHY - Ended Successfully
mv_ddr: 14.0.0
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
mv_ddr: completed successfully
Trying to boot from MMC1
===mmc_start_init start===
===Getting ext_csd===
===mmc->ext_csd[EXT_CSD_PART_CONF] = 0
===mmc_power_on===
===mmc->ext_csd[EXT_CSD_PART_CONF] = 0
===mmc_select_mode===
===mmc->ext_csd[EXT_CSD_PART_CONF] = 0
===mmc_mode2freq===
===mmc->ext_csd[EXT_CSD_PART_CONF] = 0
===mmc_set_initial_state===
===mmc->ext_csd[EXT_CSD_PART_CONF] = 0
CMD_SEND:0
ARG 0x00000000
MMC_RSP_NONE
CMD_SEND:8
ARG 0x000001aa
RET -110
CMD_SEND:55
ARG 0x00000000
RET -110
CMD_SEND:0
ARG 0x00000000
MMC_RSP_NONE
CMD_SEND:1
ARG 0x00000000
MMC_RSP_R3,4 0x40ff8080
CMD_SEND:1
ARG 0x40300080
MMC_RSP_R3,4 0x40ff8080
CMD_SEND:1
ARG 0x40300080
MMC_RSP_R3,4 0xc0ff8080
===mmc_start_init end===
===mmc->ext_csd[EXT_CSD_PART_CONF] = 0
CMD_SEND:2
ARG 0x00000000
MMC_RSP_R2 0x15010038
0x474d4534
0x52010418
0xfc4f7300
DUMPING DATA
000 - 15 01 00 38
004 - 47 4d 45 34
008 - 52 01 04 18
012 - fc 4f 73 00
CMD_SEND:3
ARG 0x00010000
MMC_RSP_R1,5,6,7 0x00000500
CMD_SEND:9
ARG 0x00010000
MMC_RSP_R2 0xd0270132
0x0f5903ff
0xf6dbffef
0x8e404000
DUMPING DATA
000 - d0 27 01 32
004 - 0f 59 03 ff
008 - f6 db ff ef
012 - 8e 40 40 00
===mmc_select_mode===
===mmc->ext_csd[EXT_CSD_PART_CONF] = 0
===mmc_mode2freq===
===mmc->ext_csd[EXT_CSD_PART_CONF] = 0
CMD_SEND:7
ARG 0x00010000
MMC_RSP_R1,5,6,7 0x00000700
CMD_SEND:8
ARG 0x00000000
MMC_RSP_R1,5,6,7 0x00000900
===mmc_startup_v4===
===mmc->ext_csd[EXT_CSD_PART_CONF] = 8
<snip>
</output>
More information about the U-Boot
mailing list