[PATCH v2 1/3] starfive: pci: Add StarFive JH7110 pcie driver
Minda Chen
minda.chen at starfivetech.com
Mon Mar 27 03:03:46 CEST 2023
On 2023/3/25 20:31, Pali Rohár wrote:
> On Friday 24 March 2023 18:57:33 Minda Chen wrote:
>> On 2023/3/24 2:19, Pali Rohár wrote:
>> > On Thursday 23 March 2023 18:51:38 Minda Chen wrote:
>> >> On 2023/3/11 1:42, Pali Rohár wrote:
>> >> > On Friday 10 March 2023 18:36:44 Minda Chen wrote:
>> >> >> On 2023/3/8 15:31, Pali Rohár wrote:
>> >> >> > Hello! See few comments below.
>> >> >> >
>> >> >> > On Wednesday 08 March 2023 13:48:31 Minda Chen wrote:
>> >> >> >> From: Mason Huo <mason.huo at starfivetech.com>
>> >> >> >>
>> >> >> >> Add pcie driver for StarFive JH7110, the driver depends on
>> >> >> >> starfive gpio, pinctrl, clk and reset driver to do init.
>> >> >> >>
>> >> >> >> Several devices are tested:
>> >> >> >> a) M.2 NVMe SSD
>> >> >> >> b) Realtek 8169 Ethernet adapter.
>> >> >> >>
>> >> >> >> Signed-off-by: Mason Huo <mason.huo at starfivetech.com>
>> >> >> >> Signed-off-by: Minda Chen <minda.chen at starfivetech.com>
>> >> >> >> ---
>> >> >> >> drivers/pci/Kconfig | 11 +
>> >> >> >> drivers/pci/Makefile | 1 +
>> >> >> >> drivers/pci/pcie_starfive_jh7110.c | 478 +++++++++++++++++++++++++++++
>> >> >> >> 3 files changed, 490 insertions(+)
>> >> >> >> create mode 100644 drivers/pci/pcie_starfive_jh7110.c
>> >> >> >>
>> >> >> >> diff --git a/drivers/pci/Kconfig b/drivers/pci/Kconfig
>> >> >> >> index ef328d2652..e7b0ff5bc3 100644
>> >> >> >> --- a/drivers/pci/Kconfig
>> >> >> >> +++ b/drivers/pci/Kconfig
>> >> >> >> @@ -374,4 +374,15 @@ config PCIE_UNIPHIER
>> >> >> >> Say Y here if you want to enable PCIe controller support on
>> >> >> >> UniPhier SoCs.
>> >> >> >>
>> >> >> >> +config PCIE_STARFIVE_JH7110
>> >> >> >> + bool "Enable Starfive JH7110 PCIe driver"
>> >> >> >> + depends on STARFIVE_JH7110
>> >> >> >> + depends on PINCTRL_STARFIVE_JH7110
>> >> >> >> + depends on CLK_JH7110
>> >> >> >> + depends on RESET_JH7110
>> >> >> >> + default y
>> >> >> >> + help
>> >> >> >> + Say Y here if you want to enable PCIe controller support on
>> >> >> >> + StarFive JH7110 SoC.
>> >> >> >> +
>> >> >> >> endif
>> >> >> >> diff --git a/drivers/pci/Makefile b/drivers/pci/Makefile
>> >> >> >> index 49506e7ba5..bbe3323bb5 100644
>> >> >> >> --- a/drivers/pci/Makefile
>> >> >> >> +++ b/drivers/pci/Makefile
>> >> >> >> @@ -49,3 +49,4 @@ obj-$(CONFIG_PCI_OCTEONTX) += pci_octeontx.o
>> >> >> >> obj-$(CONFIG_PCIE_OCTEON) += pcie_octeon.o
>> >> >> >> obj-$(CONFIG_PCIE_DW_SIFIVE) += pcie_dw_sifive.o
>> >> >> >> obj-$(CONFIG_PCIE_UNIPHIER) += pcie_uniphier.o
>> >> >> >> +obj-$(CONFIG_PCIE_STARFIVE_JH7110) += pcie_starfive_jh7110.o
>> >> >> >> diff --git a/drivers/pci/pcie_starfive_jh7110.c b/drivers/pci/pcie_starfive_jh7110.c
>> >> >> >> new file mode 100644
>> >> >> >> index 0000000000..5ccef1ef02
>> >> >> >> --- /dev/null
>> >> >> >> +++ b/drivers/pci/pcie_starfive_jh7110.c
>> >> >> >> @@ -0,0 +1,478 @@
>> >> >> >> +// SPDX-License-Identifier: GPL-2.0+
>> >> >> >> +/*
>> >> >> >> + * StarFive PLDA PCIe host controller driver
>> >> >> >> + *
>> >> >> >> + * Copyright (c) 2023 Starfive, Inc.
>> >> >> >> + * Author: Mason Huo <mason.huo at starfivetech.com>
>> >> >> >> + *
>> >> >> >> + */
>> >> >> >> +
>> >> >> >> +#include <common.h>
>> >> >> >> +#include <clk.h>
>> >> >> >> +#include <dm.h>
>> >> >> >> +#include <generic-phy.h>
>> >> >> >> +#include <pci.h>
>> >> >> >> +#include <power-domain.h>
>> >> >> >> +#include <regmap.h>
>> >> >> >> +#include <reset.h>
>> >> >> >> +#include <syscon.h>
>> >> >> >> +#include <asm/global_data.h>
>> >> >> >> +#include <asm/io.h>
>> >> >> >> +#include <asm-generic/gpio.h>
>> >> >> >> +#include <dm/device_compat.h>
>> >> >> >> +#include <dm/pinctrl.h>
>> >> >> >> +#include <linux/delay.h>
>> >> >> >> +#include <linux/iopoll.h>
>> >> >> >> +#include <power/regulator.h>
>> >> >> >> +
>> >> >> >> +DECLARE_GLOBAL_DATA_PTR;
>> >> >> >> +
>> >> >> >> +#define GEN_SETTINGS 0x80
>> >> >> >> +#define PCIE_PCI_IDS 0x9C
>> >> >> >> +#define PCIE_WINROM 0xFC
>> >> >> >> +#define PMSG_SUPPORT_RX 0x3F0
>> >> >> >> +#define PCI_MISC 0xB4
>> >> >> >> +
>> >> >> >> +#define PLDA_EP_ENABLE 0
>> >> >> >> +#define PLDA_RP_ENABLE 1
>> >> >> >> +
>> >> >> >> +#define IDS_REVISION_ID 0x02
>> >> >> >> +#define IDS_PCI_TO_PCI_BRIDGE 0x060400
>> >> >> >> +#define IDS_CLASS_CODE_SHIFT 8
>> >> >> >
>> >> >> > Please do not duplicate standard PCI macros and constants. In U-Boot
>> >> >> > they are already available in include/pci_ids.h header file.
>> >> >> >
>> >> >> ok
>> >> >> >> +#define PREF_MEM_WIN_64_SUPPORT BIT(3)
>> >> >> >> +#define PMSG_LTR_SUPPORT BIT(2)
>> >> >> >> +#define PLDA_FUNCTION_DIS BIT(15)
>> >> >> >> +#define PLDA_FUNC_NUM 4
>> >> >> >> +#define PLDA_PHY_FUNC_SHIFT 9
>> >> >> >> +
>> >> >> >> +#define XR3PCI_ATR_AXI4_SLV0 0x800
>> >> >> >> +#define XR3PCI_ATR_SRC_ADDR_LOW 0x0
>> >> >> >> +#define XR3PCI_ATR_SRC_ADDR_HIGH 0x4
>> >> >> >> +#define XR3PCI_ATR_TRSL_ADDR_LOW 0x8
>> >> >> >> +#define XR3PCI_ATR_TRSL_ADDR_HIGH 0xc
>> >> >> >> +#define XR3PCI_ATR_TRSL_PARAM 0x10
>> >> >> >> +#define XR3PCI_ATR_TABLE_OFFSET 0x20
>> >> >> >> +#define XR3PCI_ATR_MAX_TABLE_NUM 8
>> >> >> >> +
>> >> >> >> +#define XR3PCI_ATR_SRC_WIN_SIZE_SHIFT 1
>> >> >> >> +#define XR3PCI_ATR_SRC_ADDR_MASK GENMASK(31, 12)
>> >> >> >> +#define XR3PCI_ATR_TRSL_ADDR_MASK GENMASK(31, 12)
>> >> >> >> +#define XR3_PCI_ECAM_SIZE 28
>> >> >> >> +#define XR3PCI_ATR_TRSL_DIR BIT(22)
>> >> >> >> +/* IDs used in the XR3PCI_ATR_TRSL_PARAM */
>> >> >> >> +#define XR3PCI_ATR_TRSLID_PCIE_MEMORY 0x0
>> >> >> >> +#define XR3PCI_ATR_TRSLID_PCIE_CONFIG 0x1
>> >> >> >> +
>> >> >> >> +#define ECAM_BUS_SHIFT 20
>> >> >> >> +#define ECAM_DEV_SHIFT 15
>> >> >> >> +#define ECAM_FUNC_SHIFT 12
>> >> >> >
>> >> >> > Please do not implement duplicate PCIe ECAM code. U-Boot and also Linux
>> >> >> > kernel already provides PCIE_ECAM_OFFSET() macro.
>> >> >> >
>> >> >> >> +/* Secondary bus number offset in config space */
>> >> >> >> +#define PCI_SECONDARY_BUS 0x19
>> >> >> >
>> >> >> > Unused.
>> >> >> >
>> >> >> ok
>> >> >> >> +
>> >> >> >> +/* system control */
>> >> >> >> +#define STG_SYSCON_K_RP_NEP_MASK BIT(8)
>> >> >> >> +#define STG_SYSCON_AXI4_SLVL_ARFUNC_MASK GENMASK(22, 8)
>> >> >> >> +#define STG_SYSCON_AXI4_SLVL_ARFUNC_SHIFT 8
>> >> >> >> +#define STG_SYSCON_AXI4_SLVL_AWFUNC_MASK GENMASK(14, 0)
>> >> >> >> +#define STG_SYSCON_CLKREQ_MASK BIT(22)
>> >> >> >> +#define STG_SYSCON_CKREF_SRC_SHIFT 18
>> >> >> >> +#define STG_SYSCON_CKREF_SRC_MASK GENMASK(19, 18)
>> >> >> >> +
>> >> >> >> +struct starfive_pcie {
>> >> >> >> + struct udevice *dev;
>> >> >> >> +
>> >> >> >> + void __iomem *reg_base;
>> >> >> >> + void __iomem *cfg_base;
>> >> >> >> +
>> >> >> >> + struct regmap *regmap;
>> >> >> >> + u32 stg_arfun;
>> >> >> >> + u32 stg_awfun;
>> >> >> >> + u32 stg_rp_nep;
>> >> >> >> +
>> >> >> >> + struct clk_bulk clks;
>> >> >> >> + struct reset_ctl_bulk rsts;
>> >> >> >> +
>> >> >> >> + int atr_table_num;
>> >> >> >> + int first_busno;
>> >> >> >> +};
>> >> >> >> +
>> >> >> >> +static int starfive_pcie_addr_valid(pci_dev_t bdf, int first_busno)
>> >> >> >> +{
>> >> >> >> + if ((PCI_BUS(bdf) == first_busno) && (PCI_DEV(bdf) > 0))
>> >> >> >> + return 0;
>> >> >> >> + if ((PCI_BUS(bdf) == first_busno + 1) && (PCI_DEV(bdf) > 0))
>> >> >> >> + return 0;
>> >> >> >
>> >> >> > If fisrt_busno is the bus of the root port then first_busno+1 does not
>> >> >> > have to bus of the PCIe device on the other end of the link from the
>> >> >> > root port. See for example pci_mvebu.c how this logic is handled.
>> >> >> > You probably want to also limit access to non-zero function of root port
>> >> >> > unless you have multifunction root-port device.
>> >> >> >
>> >> >> root port limitation can follow the pci_mvebu.c
>> >> >
>> >> > It can follow, but question is why it should follow pci_mvebu.c. Marvell
>> >> > PCIe controller does not use ECAM, instead it uses Intel PCI conf1
>> >> > mechanism and moreover it contains HW bugs which are workarounded in
>> >> > that filter code.
>> >> >
>> >> starfive_pcie_addr_valid limit the access the non-zero device.
>> >>
>> >> The limitaion reason is list below
>> >> For PCIe bus of JH7110 SoC limitation, The PCIe host bridge of just support one device.
>> >>
>> >> (The simple topic graph)
>> >> ================ JH7110 SoC ==================
>> >> [Processor]
>> >> |
>> >> (Root Complex)
>> >> |
>> >> ------------------------------
>> >> [Host Bridge Domain 0000]
>> >> |
>> >> (Bus 0)
>> >> |
>> >> [Bus 0 Device 0]
>> >> |
>> >> ================ JH7110 SoC ==================
>> >> |
>> >> (BUS 1)
>> >> |
>> >> [BUS 1 Device 0]
>> >>
>> >> To avoid access non-zero device config space, add this limitation.
>> >
>> > Ok. The hierarchy is quite standard. But question is why you need to do
>> > explicit filtering in the driver? ECAM should correctly work also when
>> > you ask non-existent device (e.g. by returning all-ones).
>> >
>> > Is the driver working fine also without filtering?
>> >
>> >> And I can see designware PCIe code (pcie_dw_common.c) have the same
>> >> code logic(pcie_dw_addr_valid).
>> >
>> > In mvebu is explicit filtering because of HW bug which cause that HW
>> > ignores device number. And so device 0 is aliased to device 2, 3, 4...
>> > So to prevent kernel to see tons of non-existent devices, mvebu driver
>> > has to filter access.
>> >
>> > But normally any special logic should not be needed unless there is a HW
>> > bug. HW just normally returns to kernel that there is no other device.
>> >
>> > mvebu driver is not something useful for taking as a template driver for
>> > building a new driver because it contains tons of code for workarounding
>> > real HW issues without which other kernel (and userspace) PCIe parts do
>> > not work.
>> >
>> Uboot PCIe can not work well. If without filtering, uboot get duplicate
>> devices. device 0 is aliased to device 2, 3, 4...31
>
> Ok, so you are seeing same issue as on mvebu HW which I described above,
> right? And which bus is affected by this issue? Root (zero) bus? Or the
> bus behind it (1)?
>
bus 1.
>> >> >> >> +
>> >> >> >> + return 1;
>> >> >> >> +}
>> >> >> >> +
>> >> >> >> +static int starfive_pcie_off_conf(pci_dev_t bdf, uint offset)
>> >> >> >> +{
>> >> >> >> + unsigned int bus = PCI_BUS(bdf);
>> >> >> >> + unsigned int dev = PCI_DEV(bdf);
>> >> >> >> + unsigned int func = PCI_FUNC(bdf);
>> >> >> >> +
>> >> >> >> + return (bus << ECAM_BUS_SHIFT) | (dev << ECAM_DEV_SHIFT) |
>> >> >> >> + (func << ECAM_FUNC_SHIFT) | offset;
>> >> >> >> +}
>> >> >> >> +
>> >> >> >> +static bool starfive_pcie_hide_rc_bar(pci_dev_t bdf, int offset)
>> >> >> >> +{
>> >> >> >> + /* Only root port 1 is in use */
>> >> >> >> + if ((PCI_BUS(bdf) == 0) &&
>> >> >> >
>> >> >> > This looks like an incorrect check for the bus of he root port.
>> >> >> > See for example pci_mvebu.c where logic should be correct.
>> >> >> >
>> >> >> > I guess you wanted to use: PCI_BUS(bdf)-dev_seq(udev)
>> >> >> > [1] This is a work around method. Our PCIe support 64bit. But the config
>> >> >> space is 16KB. If no limitation here, uboot will set high 32 bit base address to 0xfffffff after init.
>> >> >
>> >> > I just do not understand. BAR configures PCIe MEM space mapping and it
>> >> > is fully independent of the PCIe config space. I do not see reason for
>> >> > limitation.
>> >> >
>> >> >> But this will make kernel pcie failed. This value will be not cleared.
>> >> >> While kernel read the base address first. kernel pcie can not work.
>> >> >> And our IC we can not reset the PCIe to clear this value.
>> >> >> I dont know how to fix it expcept this method.
>> >> >
>> >> > Well, this sounds like a bug in kernel, which should be fixed or at
>> >> > least reported.
>> >> >> And if in the u-boot is workaround for particular kernel bug then it
>> >> > should be properly documented with information in which kernel version
>> >> > was bug fixed. Otherwise u-boot code stay in non-maintenanceble state.
>> >> >
>> >> I am not sure whether it is a kernel issue. For this are workaround codes,
>> >> I will remove this function (starfive_pcie_hide_rc_bar) in next version. Remove this codes uboot PCIe still can work.
>> >
>> > If everything is working fine then I do not see reason for having it
>> > there.
>> >
>> >> >> >> + (offset == PCI_BASE_ADDRESS_0 || offset == PCI_BASE_ADDRESS_1))
>> >> >> >> + return true;
>> >> >> >> +
>> >> >> >> + return false;
>> >> >> >> +}
>> >> >> >> +
>> >> >> >> +static int starfive_pcie_conf_address(const struct udevice *udev, pci_dev_t bdf,
>> >> >> >> + uint offset, void **paddr)
>> >> >> >> +{
>> >> >> >> + struct starfive_pcie *priv = dev_get_priv(udev);
>> >> >> >> + int where = starfive_pcie_off_conf(bdf, offset);
>> >> >> >> +
>> >> >> >> + if (!starfive_pcie_addr_valid(bdf, priv->first_busno))
>> >> >> >> + return -EINVAL;
>> >> >> >
>> >> >> > Is this check needed? Does it mean that ECAM returns bogus information
>> >> >> > for disconnected devices, that it needs to be manually filtered? (Which
>> >> >> > is against PCIe spec).
>> >> >> >
>> >> >> I found nvme device can not work if the non-zero function of root port
>> >> >> without limitation. But I will try to fix it. Maybe I can remove this.
>> >> Please ignore this reply. I have replied wrong message. I am sorry about this
>> >> It is not 'non-zero function'. I should said 'non-zero device'. The check reason
>> >> see starfive_pcie_addr_valid reply.
>> >> > So you have multifunction root port device (if you are talking about
>> >> > non-zero function)? And what does it mean that NVMe device cannot work?
>> >> > Can you connect your device to second function of root port if it works?
>> >> >
>> >> Please ignore previous reply. And the test NVMe devices do not support
>> >> multi-function.
>> >> >> >> +
>> >> >> >> + *paddr = (void *)(priv->cfg_base + where);
>> >> >> >> + return 0;
>> >> >> >> +}
>> >> >> >> +
>> >> >> >> +static int starfive_pcie_config_read(const struct udevice *udev, pci_dev_t bdf,
>> >> >> >> + uint offset, ulong *valuep,
>> >> >> >> + enum pci_size_t size)
>> >> >> >> +{
>> >> >> >> + /* Make sure the LAST TLP is finished, before reading vendor ID. */
>> >> >> >> + if (offset == PCI_VENDOR_ID)
>> >> >> >> + mdelay(20);
>> >> >> >
>> >> >> > This looks strange. There is some bug / errata that reading vendor id
>> >> >> > from ECAM does not work correctly?
>> >> >> >
>> >> >> I will remove this. It is not a errata of reading the vendor ID.
>> >> >> >> +
>> >> >> >> + return pci_generic_mmap_read_config(udev, starfive_pcie_conf_address,
>> >> >> >> + bdf, offset, valuep, size);
>> >> >> >> +}
>> >> >> >> +
>> >> >> >> +int starfive_pcie_config_write(struct udevice *udev, pci_dev_t bdf,
>> >> >> >> + uint offset, ulong value,
>> >> >> >> + enum pci_size_t size)
>> >> >> >> +{
>> >> >> >> + if (starfive_pcie_hide_rc_bar(bdf, offset))
>> >> >> >> + return 0;
>> >> >> >
>> >> >> > Why you are ignoring writes to some offset, but not ignoring reads? And
>> >> >> > ignoring results in no-error (return value 0)?
>> >> >> >The same as [1]
>> >> >
>> >> > But this does not explain why is result ignored. I'm just lost what is
>> >> > aim or expected result here.
>> >> >
>> >> Since it is a workaround codes for booting kernel, (Writing root port base0 and base 1
>> >> register cause kernel PCIe driver can not work, So just limtation writing base0 and bas1).
>> >> I will remove starfive_pcie_hide_rc_bar as previous said.
>> >> >> >> +
>> >> >> >> + return pci_generic_mmap_write_config(udev, starfive_pcie_conf_address,
>> >> >> >> + bdf, offset, value, size);
>> >> >> >> +}
>> >> >> >> +
>> >> >> >> +static int starfive_pcie_set_atr_entry(struct starfive_pcie *priv, phys_addr_t src_addr,
>> >> >> >> + phys_addr_t trsl_addr, size_t window_size,
>> >> >> >> + int trsl_param)
>> >> >> >> +{
>> >> >> >> + void __iomem *base =
>> >> >> >> + priv->reg_base + XR3PCI_ATR_AXI4_SLV0;
>> >> >> >> +
>> >> >> >> + /* Support AXI4 Slave 0 Address Translation Tables 0-7. */
>> >> >> >> + if (priv->atr_table_num >= XR3PCI_ATR_MAX_TABLE_NUM) {
>> >> >> >> + dev_err(priv->dev, "ATR table number %d exceeds max num\n",
>> >> >> >> + priv->atr_table_num);
>> >> >> >> + return -EINVAL;
>> >> >> >> + }
>> >> >> >> + base += XR3PCI_ATR_TABLE_OFFSET * priv->atr_table_num;
>> >> >> >> + priv->atr_table_num++;
>> >> >> >> +
>> >> >> >> + /* X3PCI_ATR_SRC_ADDR_LOW:
>> >> >> >> + * - bit 0: enable entry,
>> >> >> >> + * - bits 1-6: ATR window size: total size in bytes: 2^(ATR_WSIZE + 1)
>> >> >> >> + * - bits 7-11: reserved
>> >> >> >> + * - bits 12-31: start of source address
>> >> >> >> + */
>> >> >> >> + writel((lower_32_bits(src_addr) & XR3PCI_ATR_SRC_ADDR_MASK) |
>> >> >> >> + (fls(window_size) - 1) << XR3PCI_ATR_SRC_WIN_SIZE_SHIFT | 1,
>> >> >> >> + base + XR3PCI_ATR_SRC_ADDR_LOW);
>> >> >> >> + writel(upper_32_bits(src_addr), base + XR3PCI_ATR_SRC_ADDR_HIGH);
>> >> >> >> + writel((lower_32_bits(trsl_addr) & XR3PCI_ATR_TRSL_ADDR_MASK),
>> >> >> >> + base + XR3PCI_ATR_TRSL_ADDR_LOW);
>> >> >> >> + writel(upper_32_bits(trsl_addr), base + XR3PCI_ATR_TRSL_ADDR_HIGH);
>> >> >> >> + writel(trsl_param, base + XR3PCI_ATR_TRSL_PARAM);
>> >> >> >> +
>> >> >> >> + dev_dbg(priv->dev, "ATR entry: 0x%010llx %s 0x%010llx [0x%010llx] (param: 0x%06x)\n",
>> >> >> >> + src_addr, (trsl_param & XR3PCI_ATR_TRSL_DIR) ? "<-" : "->",
>> >> >> >> + trsl_addr, (u64)window_size, trsl_param);
>> >> >> >> + return 0;
>> >> >> >> +}
>> >> >> >> +
>> >> >> >> +static int starfive_pcie_atr_init(struct starfive_pcie *priv)
>> >> >> >> +{
>> >> >> >> + struct udevice *ctlr = pci_get_controller(priv->dev);
>> >> >> >> + struct pci_controller *hose = dev_get_uclass_priv(ctlr);
>> >> >> >> + int i, ret;
>> >> >> >> +
>> >> >> >> + /* As the two host bridges in JH7110 soc have the same default
>> >> >> >> + * address translation table, this cause the second root port can't
>> >> >> >> + * access it's host bridge config space correctly.
>> >> >> >> + * To workaround, config the ATR of host bridge config space by SW.
>> >> >> >> + */
>> >> >> >> +
>> >> >> >> + ret = starfive_pcie_set_atr_entry(priv,
>> >> >> >> + (phys_addr_t)priv->cfg_base,
>> >> >> >> + 0,
>> >> >> >> + 1 << XR3_PCI_ECAM_SIZE,
>> >> >> >> + XR3PCI_ATR_TRSLID_PCIE_CONFIG);
>> >> >> >> + if (ret)
>> >> >> >> + return ret;
>> >> >> >> +
>> >> >> >> + for (i = 0; i < hose->region_count; i++) {
>> >> >> >> + if (hose->regions[i].flags == PCI_REGION_SYS_MEMORY)
>> >> >> >> + continue;
>> >> >> >> +
>> >> >> >> + /* Only support identity mappings. */
>> >> >> >> + if (hose->regions[i].bus_start !=
>> >> >> >> + hose->regions[i].phys_start)
>> >> >> >> + return -EINVAL;
>> >> >> >> +
>> >> >> >> + ret = starfive_pcie_set_atr_entry(priv,
>> >> >> >> + hose->regions[i].phys_start,
>> >> >> >> + hose->regions[i].bus_start,
>> >> >> >> + hose->regions[i].size,
>> >> >> >> + XR3PCI_ATR_TRSLID_PCIE_MEMORY);
>> >> >> >> + if (ret)
>> >> >> >> + return ret;
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + return 0;
>> >> >> >> +}
>> >> >> >> +
>> >> >> >> +static int starfive_pcie_get_syscon(struct udevice *dev)
>> >> >> >> +{
>> >> >> >> + struct starfive_pcie *priv = dev_get_priv(dev);
>> >> >> >> + struct udevice *syscon;
>> >> >> >> + struct ofnode_phandle_args syscfg_phandle;
>> >> >> >> + u32 cells[4];
>> >> >> >> + int ret;
>> >> >> >> +
>> >> >> >> + /* get corresponding syscon phandle */
>> >> >> >> + ret = dev_read_phandle_with_args(dev, "starfive,stg-syscon", NULL, 0, 0,
>> >> >> >> + &syscfg_phandle);
>> >> >> >> +
>> >> >> >> + if (ret < 0) {
>> >> >> >> + dev_err(dev, "Can't get syscfg phandle: %d\n", ret);
>> >> >> >> + return ret;
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + ret = uclass_get_device_by_ofnode(UCLASS_SYSCON, syscfg_phandle.node,
>> >> >> >> + &syscon);
>> >> >> >> + if (ret) {
>> >> >> >> + dev_err(dev, "Unable to find syscon device (%d)\n", ret);
>> >> >> >> + return ret;
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + priv->regmap = syscon_get_regmap(syscon);
>> >> >> >> + if (!priv->regmap) {
>> >> >> >> + dev_err(dev, "Unable to find regmap\n");
>> >> >> >> + return -ENODEV;
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + /* get syscon register offset */
>> >> >> >> + ret = dev_read_u32_array(dev, "starfive,stg-syscon",
>> >> >> >> + cells, ARRAY_SIZE(cells));
>> >> >> >> + if (ret) {
>> >> >> >> + dev_err(dev, "Get syscon register err %d\n", ret);
>> >> >> >> + return -EINVAL;
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + dev_dbg(dev, "Get syscon values: %x, %x, %x\n",
>> >> >> >> + cells[1], cells[2], cells[3]);
>> >> >> >> + priv->stg_arfun = cells[1];
>> >> >> >> + priv->stg_awfun = cells[2];
>> >> >> >> + priv->stg_rp_nep = cells[3];
>> >> >> >> +
>> >> >> >> + return 0;
>> >> >> >> +}
>> >> >> >> +
>> >> >> >> +static int starfive_pcie_parse_dt(struct udevice *dev)
>> >> >> >> +{
>> >> >> >> + struct starfive_pcie *priv = dev_get_priv(dev);
>> >> >> >> + int ret;
>> >> >> >> +
>> >> >> >> + priv->reg_base = (void *)dev_read_addr_name(dev, "reg");
>> >> >> >> + if (priv->reg_base == (void __iomem *)FDT_ADDR_T_NONE) {
>> >> >> >> + dev_err(dev, "Missing required reg address range\n");
>> >> >> >> + return -EINVAL;
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + priv->cfg_base = (void *)dev_read_addr_name(dev, "config");
>> >> >> >> + if (priv->cfg_base == (void __iomem *)FDT_ADDR_T_NONE) {
>> >> >> >> + dev_err(dev, "Missing required config address range");
>> >> >> >> + return -EINVAL;
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + ret = starfive_pcie_get_syscon(dev);
>> >> >> >> + if (ret) {
>> >> >> >> + dev_err(dev, "Can't get syscon: %d\n", ret);
>> >> >> >> + return ret;
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + ret = reset_get_bulk(dev, &priv->rsts);
>> >> >> >> + if (ret) {
>> >> >> >> + dev_err(dev, "Can't get reset: %d\n", ret);
>> >> >> >> + return ret;
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + ret = clk_get_bulk(dev, &priv->clks);
>> >> >> >> + if (ret) {
>> >> >> >> + dev_err(dev, "Can't get clock: %d\n", ret);
>> >> >> >> + return ret;
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + return 0;
>> >> >> >> +}
>> >> >> >> +
>> >> >> >> +static int starfive_pcie_init_port(struct udevice *dev)
>> >> >> >> +{
>> >> >> >> + int ret, i;
>> >> >> >> + unsigned int value;
>> >> >> >> + struct starfive_pcie *priv = dev_get_priv(dev);
>> >> >> >> +
>> >> >> >> + ret = clk_enable_bulk(&priv->clks);
>> >> >> >> + if (ret) {
>> >> >> >> + dev_err(dev, "Failed to enable clks (ret=%d)\n", ret);
>> >> >> >> + return ret;
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + ret = reset_deassert_bulk(&priv->rsts);
>> >> >> >> + if (ret) {
>> >> >> >> + dev_err(dev, "Failed to deassert resets (ret=%d)\n", ret);
>> >> >> >> + goto err_deassert_clk;
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + ret = pinctrl_select_state(dev, "perst-active");
>> >> >> >> + if (ret) {
>> >> >> >> + dev_err(dev, "Set perst-active pinctrl failed: %d\n", ret);
>> >> >> >> + goto err_deassert_reset;
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + /* Disable physical functions except #0 */
>> >> >> >> + for (i = 1; i < PLDA_FUNC_NUM; i++) {
>> >> >> >> + regmap_update_bits(priv->regmap,
>> >> >> >> + priv->stg_arfun,
>> >> >> >> + STG_SYSCON_AXI4_SLVL_ARFUNC_MASK,
>> >> >> >> + (i << PLDA_PHY_FUNC_SHIFT) <<
>> >> >> >> + STG_SYSCON_AXI4_SLVL_ARFUNC_SHIFT);
>> >> >> >> + regmap_update_bits(priv->regmap,
>> >> >> >> + priv->stg_awfun,
>> >> >> >> + STG_SYSCON_AXI4_SLVL_AWFUNC_MASK,
>> >> >> >> + i << PLDA_PHY_FUNC_SHIFT);
>> >> >> >> +
>> >> >> >> + value = readl(priv->reg_base + PCI_MISC);
>> >> >> >> + value |= PLDA_FUNCTION_DIS;
>> >> >> >> + writel(value, priv->reg_base + PCI_MISC);
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + /* Disable physical functions */
>> >> >> >> + regmap_update_bits(priv->regmap,
>> >> >> >> + priv->stg_arfun,
>> >> >> >> + STG_SYSCON_AXI4_SLVL_ARFUNC_MASK,
>> >> >> >> + 0);
>> >> >> >> + regmap_update_bits(priv->regmap,
>> >> >> >> + priv->stg_awfun,
>> >> >> >> + STG_SYSCON_AXI4_SLVL_AWFUNC_MASK,
>> >> >> >> + 0);
>> >> >> >> +
>> >> >> >> + /* Enable root port */
>> >> >> >> + value = readl(priv->reg_base + GEN_SETTINGS);
>> >> >> >> + value |= PLDA_RP_ENABLE;
>> >> >> >> + writel(value, priv->reg_base + GEN_SETTINGS);
>> >> >> >> +
>> >> >> >> + /* PCIe PCI Standard Configuration Identification Settings. */
>> >> >> >> + value = (IDS_PCI_TO_PCI_BRIDGE << IDS_CLASS_CODE_SHIFT) | IDS_REVISION_ID;
>> >> >> >> + writel(value, priv->reg_base + PCIE_PCI_IDS);
>> >> >> >> +
>> >> >> >> + /* The LTR message forwarding of PCIe Message Reception was set by core
>> >> >> >> + * as default, but the forward id & addr are also need to be reset.
>> >> >> >> + * If we do not disable LTR message forwarding here, or set a legal
>> >> >> >> + * forwarding address, the kernel will get stuck after this driver probe.
>> >> >> >> + * To workaround, disable the LTR message forwarding support on
>> >> >> >> + * PCIe Message Reception.
>> >> >> >> + */
>> >> >> >> + value = readl(priv->reg_base + PMSG_SUPPORT_RX);
>> >> >> >> + value &= ~PMSG_LTR_SUPPORT;
>> >> >> >> + writel(value, priv->reg_base + PMSG_SUPPORT_RX);
>> >> >> >> +
>> >> >> >> + /* Prefetchable memory window 64-bit addressing support */
>> >> >> >> + value = readl(priv->reg_base + PCIE_WINROM);
>> >> >> >> + value |= PREF_MEM_WIN_64_SUPPORT;
>> >> >> >> + writel(value, priv->reg_base + PCIE_WINROM);
>> >> >> >> +
>> >> >> >> + starfive_pcie_atr_init(priv);
>> >> >> >> +
>> >> >> >> + /* Ensure that PERST has been asserted for at least 300 ms */
>> >> >> >> + mdelay(300);
>> >> >> >> + ret = pinctrl_select_state(dev, "perst-default");
>> >> >> >> + if (ret) {
>> >> >> >> + dev_err(dev, "Set perst-default pinctrl failed: %d\n", ret);
>> >> >> >> + return ret;
>> >> >> >> + }
>> >> >> >> +
>> >> >> >> + return 0;
>> >> >> >> +
>> >> >> >> +err_deassert_clk:
>> >> >> >> + clk_disable_bulk(&priv->clks);
>> >> >> >> +err_deassert_reset:
>> >> >> >> + reset_assert_bulk(&priv->rsts);
>> >> >> >> + return ret;
>> >> >> >> +}
>> >> >> >> +
>> >> >> >> +static int starfive_pcie_probe(struct udevice *dev)
>> >> >> >> +{
>> >> >> >> + struct starfive_pcie *priv = dev_get_priv(dev);
>> >> >> >> + int ret;
>> >> >> >> +
>> >> >> >> + priv->atr_table_num = 0;
>> >> >> >> + priv->dev = dev;
>> >> >> >> + priv->first_busno = dev_seq(dev);
>> >> >> >> +
>> >> >> >> + ret = starfive_pcie_parse_dt(dev);
>> >> >> >> + if (ret)
>> >> >> >> + return ret;
>> >> >> >> +
>> >> >> >> + regmap_update_bits(priv->regmap,
>> >> >> >> + priv->stg_rp_nep,
>> >> >> >> + STG_SYSCON_K_RP_NEP_MASK,
>> >> >> >> + STG_SYSCON_K_RP_NEP_MASK);
>> >> >> >> +
>> >> >> >> + regmap_update_bits(priv->regmap,
>> >> >> >> + priv->stg_awfun,
>> >> >> >> + STG_SYSCON_CKREF_SRC_MASK,
>> >> >> >> + 2 << STG_SYSCON_CKREF_SRC_SHIFT);
>> >> >> >> +
>> >> >> >> + regmap_update_bits(priv->regmap,
>> >> >> >> + priv->stg_awfun,
>> >> >> >> + STG_SYSCON_CLKREQ_MASK,
>> >> >> >> + STG_SYSCON_CLKREQ_MASK);
>> >> >> >> +
>> >> >> >> + ret = starfive_pcie_init_port(dev);
>> >> >> >> + if (ret)
>> >> >> >> + return ret;
>> >> >> >> +
>> >> >> >> + dev_err(dev, "Starfive PCIe bus probed.\n");
>> >> >> >> +
>> >> >> >> + return 0;
>> >> >> >> +}
>> >> >> >> +
>> >> >> >> +static const struct dm_pci_ops starfive_pcie_ops = {
>> >> >> >> + .read_config = starfive_pcie_config_read,
>> >> >> >> + .write_config = starfive_pcie_config_write,
>> >> >> >> +};
>> >> >> >> +
>> >> >> >> +static const struct udevice_id starfive_pcie_ids[] = {
>> >> >> >> + { .compatible = "starfive,jh7110-pcie" },
>> >> >> >> + { }
>> >> >> >> +};
>> >> >> >> +
>> >> >> >> +U_BOOT_DRIVER(starfive_pcie_drv) = {
>> >> >> >> + .name = "starfive_7110_pcie",
>> >> >> >> + .id = UCLASS_PCI,
>> >> >> >> + .of_match = starfive_pcie_ids,
>> >> >> >> + .ops = &starfive_pcie_ops,
>> >> >> >> + .probe = starfive_pcie_probe,
>> >> >> >> + .priv_auto = sizeof(struct starfive_pcie),
>> >> >> >> +};
>> >> >> >> --
>> >> >> >> 2.17.1
>> >> >> >>
More information about the U-Boot
mailing list