[PATCH v2 2/5] net: dwc_eth_qos: Add StarFive ethernet driver glue layer
Yanhong Wang
yanhong.wang at starfivetech.com
Wed Mar 29 12:27:17 CEST 2023
The StarFive ETHQOS hardware has its own clock and reset,so add a
corresponding glue driver to configure them.
Signed-off-by: Yanhong Wang <yanhong.wang at starfivetech.com>
---
drivers/net/Kconfig | 7 +
drivers/net/Makefile | 1 +
drivers/net/dwc_eth_qos.c | 6 +
drivers/net/dwc_eth_qos.h | 1 +
drivers/net/dwc_eth_qos_starfive.c | 249 +++++++++++++++++++++++++++++
5 files changed, 264 insertions(+)
create mode 100644 drivers/net/dwc_eth_qos_starfive.c
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index ceadee98a1..161289d00f 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -249,6 +249,13 @@ config DWC_ETH_QOS_QCOM
The Synopsys Designware Ethernet QOS IP block with specific
configuration used in Qcom QCS404 SoC.
+config DWC_ETH_QOS_STARFIVE
+ bool "Synopsys DWC Ethernet QOS device support for STARFIVE"
+ depends on DWC_ETH_QOS
+ help
+ The Synopsys Designware Ethernet QOS IP block with specific
+ configuration used in STARFIVE JH7110 soc.
+
config E1000
bool "Intel PRO/1000 Gigabit Ethernet support"
depends on PCI
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 75daa5e694..69af678757 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -21,6 +21,7 @@ obj-$(CONFIG_DSA_SANDBOX) += dsa_sandbox.o
obj-$(CONFIG_DWC_ETH_QOS) += dwc_eth_qos.o
obj-$(CONFIG_DWC_ETH_QOS_IMX) += dwc_eth_qos_imx.o
obj-$(CONFIG_DWC_ETH_QOS_QCOM) += dwc_eth_qos_qcom.o
+obj-$(CONFIG_DWC_ETH_QOS_STARFIVE) += dwc_eth_qos_starfive.o
obj-$(CONFIG_E1000) += e1000.o
obj-$(CONFIG_E1000_SPI) += e1000_spi.o
obj-$(CONFIG_EEPRO100) += eepro100.o
diff --git a/drivers/net/dwc_eth_qos.c b/drivers/net/dwc_eth_qos.c
index 112deb546d..9aecd56e73 100644
--- a/drivers/net/dwc_eth_qos.c
+++ b/drivers/net/dwc_eth_qos.c
@@ -1718,6 +1718,12 @@ static const struct udevice_id eqos_ids[] = {
.data = (ulong)&eqos_qcom_config
},
#endif
+#if IS_ENABLED(CONFIG_DWC_ETH_QOS_STARFIVE)
+ {
+ .compatible = "starfive,jh7110-dwmac",
+ .data = (ulong)&eqos_jh7110_config
+ },
+#endif
{ }
};
diff --git a/drivers/net/dwc_eth_qos.h b/drivers/net/dwc_eth_qos.h
index fddbe9336c..a6b719af80 100644
--- a/drivers/net/dwc_eth_qos.h
+++ b/drivers/net/dwc_eth_qos.h
@@ -289,3 +289,4 @@ int eqos_null_ops(struct udevice *dev);
extern struct eqos_config eqos_imx_config;
extern struct eqos_config eqos_qcom_config;
+extern struct eqos_config eqos_jh7110_config;
diff --git a/drivers/net/dwc_eth_qos_starfive.c b/drivers/net/dwc_eth_qos_starfive.c
new file mode 100644
index 0000000000..5be8ac0f1a
--- /dev/null
+++ b/drivers/net/dwc_eth_qos_starfive.c
@@ -0,0 +1,249 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2023 StarFive Technology Co., Ltd.
+ * Author: Yanhong Wang<yanhong.wang at starfivetech.com>
+ */
+
+#include <common.h>
+#include <asm/cache.h>
+#include <asm/gpio.h>
+#include <clk.h>
+#include <dm.h>
+#include <eth_phy.h>
+#include <net.h>
+#include <regmap.h>
+#include <reset.h>
+#include <syscon.h>
+
+#include "dwc_eth_qos.h"
+
+#define STARFIVE_DWMAC_PHY_INFT_RGMII 0x1
+#define STARFIVE_DWMAC_PHY_INFT_RMII 0x4
+#define STARFIVE_DWMAC_PHY_INFT_FIELD 0x7U
+
+struct starfive_platform_data {
+ struct regmap *regmap;
+ struct reset_ctl_bulk resets;
+ struct clk_bulk clks;
+ phy_interface_t interface;
+ u32 offset;
+ u32 shift;
+ bool tx_use_rgmii_clk;
+};
+
+static int eqos_interface_init_jh7110(struct udevice *dev)
+{
+ struct eth_pdata *pdata = dev_get_plat(dev);
+ struct starfive_platform_data *data = pdata->priv_pdata;
+ struct ofnode_phandle_args args;
+ unsigned int mode;
+ int ret;
+
+ switch (data->interface) {
+ case PHY_INTERFACE_MODE_RMII:
+ mode = STARFIVE_DWMAC_PHY_INFT_RMII;
+ break;
+
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ mode = STARFIVE_DWMAC_PHY_INFT_RGMII;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ ret = dev_read_phandle_with_args(dev, "starfive,syscon", NULL,
+ 2, 0, &args);
+ if (ret)
+ return ret;
+
+ if (args.args_count != 2)
+ return -EINVAL;
+
+ data->offset = args.args[0];
+ data->shift = args.args[1];
+ data->regmap = syscon_regmap_lookup_by_phandle(dev, "starfive,syscon");
+ if (IS_ERR(data->regmap)) {
+ ret = PTR_ERR(data->regmap);
+ pr_err("Failed to get regmap: %d\n", ret);
+ return ret;
+ }
+
+ return regmap_update_bits(data->regmap, data->offset,
+ STARFIVE_DWMAC_PHY_INFT_FIELD << data->shift,
+ mode << data->shift);
+}
+
+static int eqos_set_tx_clk_speed_jh7110(struct udevice *dev)
+{
+ struct eqos_priv *eqos = dev_get_priv(dev);
+ struct eth_pdata *pdata = dev_get_plat(dev);
+ struct starfive_platform_data *data = pdata->priv_pdata;
+ struct clk *pclk, *c;
+ ulong rate;
+ int ret;
+
+ /* Generally, the rgmii_tx clock is provided by the internal clock,
+ * which needs to match the corresponding clock frequency according
+ * to different speeds. If the rgmii_tx clock is provided by the
+ * external rgmii_rxin, there is no need to configure the clock
+ * internally, because rgmii_rxin will be adaptively adjusted.
+ */
+ if (data->tx_use_rgmii_clk)
+ return 0;
+
+ switch (eqos->phy->speed) {
+ case SPEED_1000:
+ rate = 125 * 1000 * 1000;
+ break;
+ case SPEED_100:
+ rate = 25 * 1000 * 1000;
+ break;
+ case SPEED_10:
+ rate = 2.5 * 1000 * 1000;
+ break;
+ default:
+ pr_err("invalid speed %d", eqos->phy->speed);
+ return -EINVAL;
+ }
+
+ /* eqos->clk_tx clock has no set rate operation, so just set the parent
+ * clock rate directly
+ */
+ ret = clk_get_by_id(eqos->clk_tx.id, &c);
+ if (ret)
+ return ret;
+
+ pclk = clk_get_parent(c);
+ if (pclk) {
+ ret = clk_set_rate(pclk, rate);
+ if (ret < 0) {
+ pr_err("jh7110 (clk_tx, %lu) failed: %d", rate, ret);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static ulong eqos_get_tick_clk_rate_jh7110(struct udevice *dev)
+{
+ struct eqos_priv *eqos = dev_get_priv(dev);
+
+ return clk_get_rate(&eqos->clk_tx);
+}
+
+static int eqos_start_clks_jh7110(struct udevice *dev)
+{
+ struct eth_pdata *pdata = dev_get_plat(dev);
+ struct starfive_platform_data *data = pdata->priv_pdata;
+
+ return clk_enable_bulk(&data->clks);
+}
+
+static int eqos_stop_clks_jh7110(struct udevice *dev)
+{
+ struct eth_pdata *pdata = dev_get_plat(dev);
+ struct starfive_platform_data *data = pdata->priv_pdata;
+
+ return clk_disable_bulk(&data->clks);
+}
+
+static int eqos_start_resets_jh7110(struct udevice *dev)
+{
+ struct eth_pdata *pdata = dev_get_plat(dev);
+ struct starfive_platform_data *data = pdata->priv_pdata;
+
+ return reset_deassert_bulk(&data->resets);
+}
+
+static int eqos_stop_resets_jh7110(struct udevice *dev)
+{
+ struct eth_pdata *pdata = dev_get_plat(dev);
+ struct starfive_platform_data *data = pdata->priv_pdata;
+
+ return reset_assert_bulk(&data->resets);
+}
+
+static int eqos_remove_resources_jh7110(struct udevice *dev)
+{
+ struct eth_pdata *pdata = dev_get_plat(dev);
+ struct starfive_platform_data *data = pdata->priv_pdata;
+
+ reset_assert_bulk(&data->resets);
+ clk_disable_bulk(&data->clks);
+
+ return 0;
+}
+
+static int eqos_probe_resources_jh7110(struct udevice *dev)
+{
+ struct eqos_priv *eqos = dev_get_priv(dev);
+ struct eth_pdata *pdata = dev_get_plat(dev);
+ struct starfive_platform_data *data;
+ int ret;
+
+ data = calloc(1, sizeof(struct starfive_platform_data));
+ if (!data)
+ return -ENOMEM;
+
+ pdata->priv_pdata = data;
+ data->interface = eqos->config->interface(dev);
+ if (data->interface == PHY_INTERFACE_MODE_NA) {
+ pr_err("Invalid PHY interface\n");
+ return -EINVAL;
+ }
+
+ ret = reset_get_bulk(dev, &data->resets);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_get_bulk(dev, &data->clks);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_get_by_name(dev, "gtx", &eqos->clk_tx);
+ if (ret)
+ return ret;
+
+ data->tx_use_rgmii_clk = dev_read_bool(dev, "starfive,tx-use-rgmii-clk");
+
+ return eqos_interface_init_jh7110(dev);
+}
+
+static struct eqos_ops eqos_jh7110_ops = {
+ .eqos_inval_desc = eqos_inval_desc_generic,
+ .eqos_flush_desc = eqos_flush_desc_generic,
+ .eqos_inval_buffer = eqos_inval_buffer_generic,
+ .eqos_flush_buffer = eqos_flush_buffer_generic,
+ .eqos_probe_resources = eqos_probe_resources_jh7110,
+ .eqos_remove_resources = eqos_remove_resources_jh7110,
+ .eqos_stop_resets = eqos_stop_resets_jh7110,
+ .eqos_start_resets = eqos_start_resets_jh7110,
+ .eqos_stop_clks = eqos_stop_clks_jh7110,
+ .eqos_start_clks = eqos_start_clks_jh7110,
+ .eqos_calibrate_pads = eqos_null_ops,
+ .eqos_disable_calibration = eqos_null_ops,
+ .eqos_set_tx_clk_speed = eqos_set_tx_clk_speed_jh7110,
+ .eqos_get_enetaddr = eqos_null_ops,
+ .eqos_get_tick_clk_rate = eqos_get_tick_clk_rate_jh7110
+};
+
+/* mdio_wait: There is no need to wait after setting the MAC_MDIO_Address register
+ * swr_wait: Software reset bit must be read at least 4 CSR clock cycles
+ * after it is written to 1.
+ * config_mac: Enable rx queue to DCB mode.
+ * config_mac_mdio: CSR clock range is 250-300 Mhz.
+ * axi_bus_width: The width of the data bus is 64 bit.
+ */
+struct eqos_config __maybe_unused eqos_jh7110_config = {
+ .reg_access_always_ok = false,
+ .mdio_wait = 0,
+ .swr_wait = 4,
+ .config_mac = EQOS_MAC_RXQ_CTRL0_RXQ0EN_ENABLED_DCB,
+ .config_mac_mdio = EQOS_MAC_MDIO_ADDRESS_CR_250_300,
+ .axi_bus_width = EQOS_AXI_WIDTH_64,
+ .interface = dev_read_phy_mode,
+ .ops = &eqos_jh7110_ops
+};
--
2.17.1
More information about the U-Boot
mailing list