[PATCH v2 7/9] spi: bcm63xx-hsspi: Add prepend mode support
William Zhang
william.zhang at broadcom.com
Tue May 2 20:58:14 CEST 2023
Due to the controller limitation to keep the chip select low during the
bus idle time between the transfer, a dummy cs workaround was used when
this driver was first upstreamed to the u-boot based on linux kernel
driver. It basically picks the dummy cs as !actual_cs so typically dummy
cs is 1 when most of the case only cs 0 is used in the board design.
Then invert the polarity of both cs and tell the controller to start the
transfers using dummy cs. Assuming both cs are active low before the
inversion, effectively this keeps dummy cs high and actual cs low during
the transfer and workaround the issue.
This workaround requires that dummy cs 1 pin to is set to SPI chip
selection function in the pinmux when the transfer clock is above 25MHz.
The old chips likely have default pinmux set to chip select on the dummy
cs pin so it works but this is not case for the new Broadband BCA chips
and this workaround stop working. This is specifically an issue to
support SPI NAND and SPI NOR flash because these flash devices can
typically run at or above 100MHz.
This patch utilizes the prepend feature of the controller to combine the
multiple transfers in the same message to a single transfer when
possible. This way there is no need to keep clock low between transfers
and solve the issue without any pinmux requirement.
Multiple transfers within a SPI message may be combined into one
transfer if the following are all true:
* One or more half duplex write transfer in single bit mode
* Optional full duplex read/write at the end
* No delay and cs_change between transfers
Most of the SPI device meets this requirements such as SPI NOR, SPI NAND
flash, Broadcom SPI voice card and etc. So this change switches to the
prepend mode as the default mode. For any SPI message that does not meet
the above requirement, we switch to original dummy cs mode but limit the
clock rate to the safe 25MHz.
Port from linux patch:
Link: https://lore.kernel.org/r/20230209200246.141520-12-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang at broadcom.com>
---
Changes in v2: None
drivers/spi/bcm63xx_hsspi.c | 259 +++++++++++++++++++++++++++++++++---
1 file changed, 242 insertions(+), 17 deletions(-)
diff --git a/drivers/spi/bcm63xx_hsspi.c b/drivers/spi/bcm63xx_hsspi.c
index 0d12c345b1dd..a24bb430cbb4 100644
--- a/drivers/spi/bcm63xx_hsspi.c
+++ b/drivers/spi/bcm63xx_hsspi.c
@@ -20,7 +20,13 @@
#define HSSPI_PP 0
-#define SPI_MAX_SYNC_CLOCK 30000000
+/*
+ * The maximum frequency for SPI synchronous mode is 30MHz for some chips and
+ * 25MHz for some others. This depends on the chip layout and SPI signals
+ * distance to the pad. We use the lower of these values to cover all relevant
+ * chips.
+ */
+#define SPI_MAX_SYNC_CLOCK 25000000
/* SPI Control register */
#define SPI_CTL_REG 0x000
@@ -72,12 +78,16 @@
#define SPI_PFL_MODE_REG(x) (0x100 + (0x20 * (x)) + 0x08)
#define SPI_PFL_MODE_FILL_SHIFT 0
#define SPI_PFL_MODE_FILL_MASK (0xff << SPI_PFL_MODE_FILL_SHIFT)
+#define SPI_PFL_MODE_MDRDST_SHIFT 8
+#define SPI_PFL_MODE_MDWRST_SHIFT 12
#define SPI_PFL_MODE_MDRDSZ_SHIFT 16
#define SPI_PFL_MODE_MDRDSZ_MASK (1 << SPI_PFL_MODE_MDRDSZ_SHIFT)
#define SPI_PFL_MODE_MDWRSZ_SHIFT 18
#define SPI_PFL_MODE_MDWRSZ_MASK (1 << SPI_PFL_MODE_MDWRSZ_SHIFT)
#define SPI_PFL_MODE_3WIRE_SHIFT 20
#define SPI_PFL_MODE_3WIRE_MASK (1 << SPI_PFL_MODE_3WIRE_SHIFT)
+#define SPI_PFL_MODE_PREPCNT_SHIFT 24
+#define SPI_PFL_MODE_PREPCNT_MASK (4 << SPI_PFL_MODE_PREPCNT_SHIFT)
/* SPI Ping-Pong FIFO registers */
#define HSSPI_FIFO_SIZE 0x200
@@ -96,12 +106,21 @@
#define HSSPI_FIFO_OP_CODE_W (2 << HSSPI_FIFO_OP_CODE_SHIFT)
#define HSSPI_FIFO_OP_CODE_R (3 << HSSPI_FIFO_OP_CODE_SHIFT)
+#define HSSPI_MAX_DATA_SIZE (HSSPI_FIFO_SIZE - HSSPI_FIFO_OP_SIZE)
+#define HSSPI_MAX_PREPEND_SIZE 15
+
+#define HSSPI_XFER_MODE_PREPEND 0
+#define HSSPI_XFER_MODE_DUMMYCS 1
+
struct bcm63xx_hsspi_priv {
void __iomem *regs;
ulong clk_rate;
uint8_t num_cs;
uint8_t cs_pols;
uint speed;
+ uint xfer_mode;
+ uint32_t prepend_cnt;
+ uint8_t prepend_buf[HSSPI_MAX_PREPEND_SIZE];
};
static int bcm63xx_hsspi_cs_info(struct udevice *bus, uint cs,
@@ -143,9 +162,16 @@ static void bcm63xx_hsspi_activate_cs(struct bcm63xx_hsspi_priv *priv,
struct dm_spi_slave_plat *plat)
{
uint32_t clr, set;
+ uint speed = priv->speed;
+
+ if (priv->xfer_mode == HSSPI_XFER_MODE_DUMMYCS &&
+ speed > SPI_MAX_SYNC_CLOCK) {
+ speed = SPI_MAX_SYNC_CLOCK;
+ debug("Force to dummy cs mode. Reduce the speed to %dHz\n", speed);
+ }
/* profile clock */
- set = DIV_ROUND_UP(priv->clk_rate, priv->speed);
+ set = DIV_ROUND_UP(priv->clk_rate, speed);
set = DIV_ROUND_UP(2048, set);
set &= SPI_PFL_CLK_FREQ_MASK;
set |= SPI_PFL_CLK_RSTLOOP_MASK;
@@ -164,7 +190,7 @@ static void bcm63xx_hsspi_activate_cs(struct bcm63xx_hsspi_priv *priv,
set |= SPI_PFL_SIG_LATCHRIS_MASK;
/* async clk */
- if (priv->speed > SPI_MAX_SYNC_CLOCK)
+ if (speed > SPI_MAX_SYNC_CLOCK)
set |= SPI_PFL_SIG_ASYNCIN_MASK;
clrsetbits_32(priv->regs + SPI_PFL_SIG_REG(plat->cs), clr, set);
@@ -173,17 +199,24 @@ static void bcm63xx_hsspi_activate_cs(struct bcm63xx_hsspi_priv *priv,
set = 0;
clr = 0;
- /* invert cs polarity */
- if (priv->cs_pols & BIT(plat->cs))
- clr |= BIT(plat->cs);
- else
- set |= BIT(plat->cs);
-
- /* invert dummy cs polarity */
- if (priv->cs_pols & BIT(!plat->cs))
- clr |= BIT(!plat->cs);
- else
- set |= BIT(!plat->cs);
+ if (priv->xfer_mode == HSSPI_XFER_MODE_PREPEND) {
+ if (priv->cs_pols & BIT(plat->cs))
+ set |= BIT(plat->cs);
+ else
+ clr |= BIT(plat->cs);
+ } else {
+ /* invert cs polarity */
+ if (priv->cs_pols & BIT(plat->cs))
+ clr |= BIT(plat->cs);
+ else
+ set |= BIT(plat->cs);
+
+ /* invert dummy cs polarity */
+ if (priv->cs_pols & BIT(!plat->cs))
+ clr |= BIT(!plat->cs);
+ else
+ set |= BIT(!plat->cs);
+ }
clrsetbits_32(priv->regs + SPI_CTL_REG, clr, set);
}
@@ -212,13 +245,18 @@ static void bcm63xx_hsspi_deactivate_cs(struct bcm63xx_hsspi_priv *priv)
* all the time. This hack is also used in the upstream linux driver and
* allows keeping CS active between transfers even if the HW doesn't give
* this possibility.
+ *
+ * This workaround only works when the dummy CS (usually CS1 when the actual
+ * CS is 0) pinmuxed to SPI chip select function if SPI clock is faster than
+ * SPI_MAX_SYNC_CLOCK. In old broadcom chip, CS1 pin is default to chip select
+ * function. But this is not the case for new chips. To make this function
+ * always work, it should be called with maximum clock of SPI_MAX_SYNC_CLOCK.
*/
-static int bcm63xx_hsspi_xfer(struct udevice *dev, unsigned int bitlen,
- const void *dout, void *din, unsigned long flags)
+static int bcm63xx_hsspi_xfer_dummy_cs(struct udevice *dev, unsigned int data_bytes,
+ const void *dout, void *din, unsigned long flags)
{
struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
struct dm_spi_slave_plat *plat = dev_get_parent_plat(dev);
- size_t data_bytes = bitlen / 8;
size_t step_size = HSSPI_FIFO_SIZE;
uint16_t opcode = 0;
uint32_t val = SPI_PFL_MODE_FILL_MASK;
@@ -304,6 +342,182 @@ static int bcm63xx_hsspi_xfer(struct udevice *dev, unsigned int bitlen,
return 0;
}
+static int bcm63xx_prepare_prepend_transfer(struct bcm63xx_hsspi_priv *priv,
+ unsigned int data_bytes, const void *dout, void *din,
+ unsigned long flags)
+{
+ /*
+ * only support multiple half duplex write transfer + optional
+ * full duplex read/write at the end.
+ */
+ if (flags & SPI_XFER_BEGIN) {
+ /* clear prepends */
+ priv->prepend_cnt = 0;
+ }
+
+ if (din) {
+ /* buffering reads not possible for prepend mode */
+ if (!(flags & SPI_XFER_END)) {
+ debug("unable to buffer reads\n");
+ return HSSPI_XFER_MODE_DUMMYCS;
+ }
+
+ /* check rx size */
+ if (data_bytes > HSSPI_MAX_DATA_SIZE) {
+ debug("max rx bytes exceeded\n");
+ return HSSPI_XFER_MODE_DUMMYCS;
+ }
+ }
+
+ if (dout) {
+ /* check tx size */
+ if (flags & SPI_XFER_END) {
+ if (priv->prepend_cnt + data_bytes > HSSPI_MAX_DATA_SIZE) {
+ debug("max tx bytes exceeded\n");
+ return HSSPI_XFER_MODE_DUMMYCS;
+ }
+ } else {
+ if (priv->prepend_cnt + data_bytes > HSSPI_MAX_PREPEND_SIZE) {
+ debug("max prepend bytes exceeded\n");
+ return HSSPI_XFER_MODE_DUMMYCS;
+ }
+
+ /*
+ * buffer transfer data in the prepend buf in case we have to fall
+ * back to dummy cs mode.
+ */
+ memcpy(&priv->prepend_buf[priv->prepend_cnt], dout, data_bytes);
+ priv->prepend_cnt += data_bytes;
+ }
+ }
+
+ return HSSPI_XFER_MODE_PREPEND;
+}
+
+static int bcm63xx_hsspi_xfer_prepend(struct udevice *dev, unsigned int data_bytes,
+ const void *dout, void *din, unsigned long flags)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
+ struct dm_spi_slave_plat *plat = dev_get_parent_plat(dev);
+ uint16_t opcode = 0;
+ uint32_t val, offset;
+ int ret;
+
+ if (flags & SPI_XFER_END) {
+ offset = HSSPI_FIFO_BASE + HSSPI_FIFO_OP_SIZE;
+ if (priv->prepend_cnt) {
+ /* copy prepend data */
+ memcpy_toio(priv->regs + offset,
+ priv->prepend_buf, priv->prepend_cnt);
+ }
+
+ if (dout && data_bytes) {
+ /* copy tx data */
+ offset += priv->prepend_cnt;
+ memcpy_toio(priv->regs + offset, dout, data_bytes);
+ }
+
+ bcm63xx_hsspi_activate_cs(priv, plat);
+ if (dout && !din) {
+ /* all half-duplex write. merge to single write */
+ data_bytes += priv->prepend_cnt;
+ opcode = HSSPI_FIFO_OP_CODE_W;
+ priv->prepend_cnt = 0;
+ } else if (!dout && din) {
+ /* half-duplex read with prepend write */
+ opcode = HSSPI_FIFO_OP_CODE_R;
+ } else {
+ /* full duplex read/write */
+ opcode = HSSPI_FIFO_OP_READ_WRITE;
+ }
+
+ /* profile mode */
+ val = SPI_PFL_MODE_FILL_MASK;
+ if (plat->mode & SPI_3WIRE)
+ val |= SPI_PFL_MODE_3WIRE_MASK;
+
+ /* dual mode */
+ if ((opcode == HSSPI_FIFO_OP_CODE_R && (plat->mode & SPI_RX_DUAL)) ||
+ (opcode == HSSPI_FIFO_OP_CODE_W && (plat->mode & SPI_TX_DUAL))) {
+ opcode |= HSSPI_FIFO_OP_MBIT_MASK;
+
+ if (plat->mode & SPI_RX_DUAL) {
+ val |= SPI_PFL_MODE_MDRDSZ_MASK;
+ val |= priv->prepend_cnt << SPI_PFL_MODE_MDRDST_SHIFT;
+ }
+ if (plat->mode & SPI_TX_DUAL) {
+ val |= SPI_PFL_MODE_MDWRSZ_MASK;
+ val |= priv->prepend_cnt << SPI_PFL_MODE_MDWRST_SHIFT;
+ }
+ }
+ val |= (priv->prepend_cnt << SPI_PFL_MODE_PREPCNT_SHIFT);
+ writel(val, priv->regs + SPI_PFL_MODE_REG(plat->cs));
+
+ /* set fifo operation */
+ val = opcode | (data_bytes & HSSPI_FIFO_OP_BYTES_MASK);
+ writew(cpu_to_be16(val),
+ priv->regs + HSSPI_FIFO_OP_REG);
+
+ /* issue the transfer */
+ val = SPI_CMD_OP_START;
+ val |= (plat->cs << SPI_CMD_PFL_SHIFT) &
+ SPI_CMD_PFL_MASK;
+ val |= (plat->cs << SPI_CMD_SLAVE_SHIFT) &
+ SPI_CMD_SLAVE_MASK;
+ writel(val, priv->regs + SPI_CMD_REG);
+
+ /* wait for completion */
+ ret = wait_for_bit_32(priv->regs + SPI_STAT_REG,
+ SPI_STAT_SRCBUSY_MASK, false,
+ 1000, false);
+ if (ret) {
+ bcm63xx_hsspi_deactivate_cs(priv);
+ printf("spi polling timeout\n");
+ return ret;
+ }
+
+ /* copy rx data */
+ if (din)
+ memcpy_fromio(din, priv->regs + HSSPI_FIFO_BASE,
+ data_bytes);
+ bcm63xx_hsspi_deactivate_cs(priv);
+ }
+
+ return 0;
+}
+
+static int bcm63xx_hsspi_xfer(struct udevice *dev, unsigned int bitlen,
+ const void *dout, void *din, unsigned long flags)
+{
+ struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
+ int ret;
+ u32 data_bytes = bitlen >> 3;
+
+ if (priv->xfer_mode == HSSPI_XFER_MODE_PREPEND) {
+ priv->xfer_mode =
+ bcm63xx_prepare_prepend_transfer(priv, data_bytes, dout, din, flags);
+ }
+
+ /* if not prependable, fall back to dummy cs mode with safe clock */
+ if (priv->xfer_mode == HSSPI_XFER_MODE_DUMMYCS) {
+ /* For pending prepend data from previous transfers, send it first */
+ if (priv->prepend_cnt) {
+ bcm63xx_hsspi_xfer_dummy_cs(dev, priv->prepend_cnt,
+ priv->prepend_buf, NULL,
+ (flags & ~SPI_XFER_END) | SPI_XFER_BEGIN);
+ priv->prepend_cnt = 0;
+ }
+ ret = bcm63xx_hsspi_xfer_dummy_cs(dev, data_bytes, dout, din, flags);
+ } else {
+ ret = bcm63xx_hsspi_xfer_prepend(dev, data_bytes, dout, din, flags);
+ }
+
+ if (flags & SPI_XFER_END)
+ priv->xfer_mode = HSSPI_XFER_MODE_PREPEND;
+
+ return ret;
+}
+
static const struct dm_spi_ops bcm63xx_hsspi_ops = {
.cs_info = bcm63xx_hsspi_cs_info,
.set_mode = bcm63xx_hsspi_set_mode,
@@ -321,6 +535,7 @@ static int bcm63xx_hsspi_child_pre_probe(struct udevice *dev)
{
struct bcm63xx_hsspi_priv *priv = dev_get_priv(dev->parent);
struct dm_spi_slave_plat *plat = dev_get_parent_plat(dev);
+ struct spi_slave *slave = dev_get_parent_priv(dev);
/* check cs */
if (plat->cs >= priv->num_cs) {
@@ -334,6 +549,13 @@ static int bcm63xx_hsspi_child_pre_probe(struct udevice *dev)
else
priv->cs_pols &= ~BIT(plat->cs);
+ /*
+ * set the max read/write size to make sure each xfer are within the
+ * prepend limit
+ */
+ slave->max_read_size = HSSPI_MAX_DATA_SIZE;
+ slave->max_write_size = HSSPI_MAX_DATA_SIZE;
+
return 0;
}
@@ -395,6 +617,9 @@ static int bcm63xx_hsspi_probe(struct udevice *dev)
priv->cs_pols = readl(priv->regs + SPI_CTL_REG) &
SPI_CTL_CS_POL_MASK;
+ /* default in prepend mode */
+ priv->xfer_mode = HSSPI_XFER_MODE_PREPEND;
+
return 0;
}
--
2.37.3
More information about the U-Boot
mailing list