[PATCH 3/4] usb: Move SPL_USB_GADGET and related Kconfig symbols to drivers/usb/
Marek Vasut
marex at denx.de
Sat May 6 16:42:39 CEST 2023
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_GADGET and related symbols. Fix typo and
rename SPL_USB_GADGET to "USB Gadget Support in SPL" .
Update the gadget Makefile to match the symbol changes.
Signed-off-by: Marek Vasut <marex at denx.de>
---
Cc: Andrew Davis <afd at ti.com>
Cc: Chris Packham <judge.packham at gmail.com>
Cc: Jim Liu <jim.t90615 at gmail.com>
Cc: Lukasz Majewski <lukma at denx.de>
Cc: Samuel Holland <samuel at sholland.org>
Cc: Simon Glass <sjg at chromium.org>
Cc: Stefan Roese <sr at denx.de>
Cc: Tom Rini <trini at konsulko.com>
Cc: Weijie Gao <weijie.gao at mediatek.com>
---
common/spl/Kconfig | 63 ------------------------------------
drivers/usb/gadget/Kconfig | 64 +++++++++++++++++++++++++++++++++++++
drivers/usb/gadget/Makefile | 5 ++-
3 files changed, 66 insertions(+), 66 deletions(-)
diff --git a/common/spl/Kconfig b/common/spl/Kconfig
index 5ad29af21cb..6774ba5b42e 100644
--- a/common/spl/Kconfig
+++ b/common/spl/Kconfig
@@ -1345,69 +1345,6 @@ config SPL_THERMAL
automatic power-off when the temperature gets too high or low. Other
devices may be discrete but connected on a suitable bus.
-config SPL_USB_GADGET
- bool "Suppport USB Gadget drivers"
- help
- Enable USB Gadget API which allows to enable USB device functions
- in SPL.
-
-if SPL_USB_GADGET
-
-config SPL_USB_ETHER
- bool "Support USB Ethernet drivers"
- depends on SPL_NET
- help
- Enable access to the USB network subsystem and associated
- drivers in SPL. This permits SPL to load U-Boot over a
- USB-connected Ethernet link (such as a USB Ethernet dongle) rather
- than from an onboard peripheral. Environment support is required
- since the network stack uses a number of environment variables.
- See also SPL_NET and SPL_ETH.
-
-config SPL_DFU
- bool "Support DFU (Device Firmware Upgrade)"
- select SPL_HASH
- select SPL_DFU_NO_RESET
- depends on SPL_RAM_SUPPORT
- help
- This feature enables the DFU (Device Firmware Upgrade) in SPL with
- RAM memory device support. The ROM code will load and execute
- the SPL built with dfu. The user can load binaries (u-boot/kernel) to
- selected device partition from host-pc using dfu-utils.
- This feature is useful to flash the binaries to factory or bare-metal
- boards using USB interface.
-
-choice
- bool "DFU device selection"
- depends on SPL_DFU
-
-config SPL_DFU_RAM
- bool "RAM device"
- depends on SPL_DFU && SPL_RAM_SUPPORT
- help
- select RAM/DDR memory device for loading binary images
- (u-boot/kernel) to the selected device partition using
- DFU and execute the u-boot/kernel from RAM.
-
-endchoice
-
-config SPL_USB_SDP_SUPPORT
- bool "Support SDP (Serial Download Protocol)"
- depends on SPL_SERIAL
- help
- Enable Serial Download Protocol (SDP) device support in SPL. This
- allows to download images into memory and execute (jump to) them
- using the same protocol as implemented by the i.MX family's boot ROM.
-
-config SPL_SDP_USB_DEV
- int "SDP USB controller index"
- default 0
- depends on SPL_USB_SDP_SUPPORT
- help
- Some boards have USB controller other than 0. Define this option
- so it can be used in compiled environment.
-endif
-
config SPL_WATCHDOG
bool "Support watchdog drivers"
imply SPL_WDT if !HW_WATCHDOG
diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
index 941f97c96d0..6f85089a9bf 100644
--- a/drivers/usb/gadget/Kconfig
+++ b/drivers/usb/gadget/Kconfig
@@ -36,6 +36,12 @@ menuconfig USB_GADGET
peripheral/device side bus controller, and a "gadget driver" for
your peripheral protocol.
+config SPL_USB_GADGET
+ bool "USB Gadget Support in SPL"
+ help
+ Enable USB Gadget API which allows to enable USB device functions
+ in SPL.
+
if USB_GADGET
config USB_GADGET_MANUFACTURER
@@ -265,3 +271,61 @@ config USBNET_HOST_ADDR
endif # USB_ETHER
endif # USB_GADGET
+
+if SPL_USB_GADGET
+
+config SPL_USB_ETHER
+ bool "Support USB Ethernet drivers in SPL"
+ depends on SPL_NET
+ help
+ Enable access to the USB network subsystem and associated
+ drivers in SPL. This permits SPL to load U-Boot over a
+ USB-connected Ethernet link (such as a USB Ethernet dongle) rather
+ than from an onboard peripheral. Environment support is required
+ since the network stack uses a number of environment variables.
+ See also SPL_NET and SPL_ETH.
+
+config SPL_DFU
+ bool "Support DFU (Device Firmware Upgrade) in SPL"
+ select SPL_HASH
+ select SPL_DFU_NO_RESET
+ depends on SPL_RAM_SUPPORT
+ help
+ This feature enables the DFU (Device Firmware Upgrade) in SPL with
+ RAM memory device support. The ROM code will load and execute
+ the SPL built with dfu. The user can load binaries (u-boot/kernel) to
+ selected device partition from host-pc using dfu-utils.
+ This feature is useful to flash the binaries to factory or bare-metal
+ boards using USB interface.
+
+choice
+ bool "DFU device selection in SPL"
+ depends on SPL_DFU
+
+config SPL_DFU_RAM
+ bool "RAM device"
+ depends on SPL_DFU && SPL_RAM_SUPPORT
+ help
+ select RAM/DDR memory device for loading binary images
+ (u-boot/kernel) to the selected device partition using
+ DFU and execute the u-boot/kernel from RAM.
+
+endchoice
+
+config SPL_USB_SDP_SUPPORT
+ bool "Support SDP (Serial Download Protocol) in SPL"
+ depends on SPL_SERIAL
+ help
+ Enable Serial Download Protocol (SDP) device support in SPL. This
+ allows to download images into memory and execute (jump to) them
+ using the same protocol as implemented by the i.MX family's boot ROM.
+
+config SPL_SDP_USB_DEV
+ int "SDP USB controller index in SPL"
+ default 0
+ depends on SPL_USB_SDP_SUPPORT
+ help
+ Some boards have USB controller other than 0. Define this option
+ so it can be used in compiled environment.
+
+endif # SPL_USB_GADGET
diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile
index 6cfe0f3a041..a9edeb9f396 100644
--- a/drivers/usb/gadget/Makefile
+++ b/drivers/usb/gadget/Makefile
@@ -3,8 +3,8 @@
# (C) Copyright 2000-2007
# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-obj-$(CONFIG_USB_GADGET) += epautoconf.o config.o usbstring.o
-obj-$(CONFIG_USB_ETHER) += epautoconf.o config.o usbstring.o
+obj-$(CONFIG_$(SPL_TPL_)USB_GADGET) += epautoconf.o config.o usbstring.o
+obj-$(CONFIG_$(SPL_TPL_)USB_ETHER) += epautoconf.o config.o usbstring.o ether.o
ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_SPL_USB_GADGET) += g_dnl.o
@@ -34,7 +34,6 @@ endif
obj-$(CONFIG_CI_UDC) += ci_udc.o
-obj-$(CONFIG_USB_ETHER) += ether.o
obj-$(CONFIG_USB_ETH_RNDIS) += rndis.o
# Devices not related to the new gadget layer depend on CONFIG_USB_DEVICE
--
2.39.2
More information about the U-Boot
mailing list