[PATCH v2 5/5] imx8mn-var-som: adjust PHY reset gpios according to hardware configuration

Hugo Villeneuve hugo at hugovil.com
Thu May 25 23:02:29 CEST 2023


From: Hugo Villeneuve <hvilleneuve at dimonoff.com>

For SOM with the EC configuration, the ethernet PHY is located on the
SOM itself, and connected to the CPU ethernet controller. It has a
reset line controlled via GPIO1_IO9. In this configuration, the PHY
located on the carrier board is not connected to anything and is
therefore not used.

For SOM without EC configuration, the ethernet PHY on the carrier
board is connected to the CPU ethernet controller. It has a reset line
controlled via the GPIO expander PCA9534_IO5.

The hardware configuration (EC) is determined at runtime by
reading from the SOM EEPROM.

To support both hardware configurations (EC and non-EC), adjust/fix
the PHY reset gpios according to the hardware configuration
read at runtime from the SOM EEPROM. This adjustement is done in
U-Boot (OF_BOARD_FIXUP) and kernel (OF_BOARD_SETUP) device trees.

Signed-off-by: Hugo Villeneuve <hvilleneuve at dimonoff.com>
---
 arch/arm/dts/imx8mn-var-som-symphony.dts      |  4 -
 .../variscite/imx8mn_var_som/imx8mn_var_som.c | 80 +++++++++++++++++++
 configs/imx8mn_var_som_defconfig              |  2 +
 3 files changed, 82 insertions(+), 4 deletions(-)

diff --git a/arch/arm/dts/imx8mn-var-som-symphony.dts b/arch/arm/dts/imx8mn-var-som-symphony.dts
index 3ed7021a48..5c8e4e8175 100644
--- a/arch/arm/dts/imx8mn-var-som-symphony.dts
+++ b/arch/arm/dts/imx8mn-var-som-symphony.dts
@@ -56,10 +56,6 @@
 	};
 };
 
-&ethphy {
-	reset-gpios = <&pca9534 5 GPIO_ACTIVE_HIGH>;
-};
-
 &i2c2 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default";
diff --git a/board/variscite/imx8mn_var_som/imx8mn_var_som.c b/board/variscite/imx8mn_var_som/imx8mn_var_som.c
index a89457e8f5..61b9455a8f 100644
--- a/board/variscite/imx8mn_var_som/imx8mn_var_som.c
+++ b/board/variscite/imx8mn_var_som/imx8mn_var_som.c
@@ -14,6 +14,7 @@
 #include <malloc.h>
 #include <asm/io.h>
 #include <asm/global_data.h>
+#include <dt-bindings/gpio/gpio.h>
 #include <linux/libfdt.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -161,4 +162,83 @@ int checkboard(void)
 
 #endif /* CONFIG_DISPLAY_BOARDINFO */
 
+static int insert_gpios_prop(void *blob, int node, const char *prop,
+			     unsigned int phandle, u32 gpio, u32 flags)
+{
+	fdt32_t val[3] = { cpu_to_fdt32(phandle), cpu_to_fdt32(gpio),
+			   cpu_to_fdt32(flags) };
+	return fdt_setprop(blob, node, prop, &val, sizeof(val));
+}
+
+static int configure_phy_reset_gpios(void *blob)
+{
+	int node;
+	int phynode;
+	int ret;
+	u32 handle;
+	u32 gpio;
+	u32 flags;
+	char path[1024];
+	const char *eth_alias = "ethernet0";
+
+	snprintf(path, sizeof(path), "%s/mdio/ethernet-phy at 4",
+		 fdt_get_alias(blob, eth_alias));
+
+	phynode = fdt_path_offset(blob, path);
+	if (phynode < 0) {
+		pr_err("%s(): unable to locate PHY node: %s\n", __func__, path);
+		return 0;
+	}
+
+	if (gd_board_type() & VAR_EEPROM_F_ETH) {
+		snprintf(path, sizeof(path), "%s",
+			 fdt_get_alias(blob, "gpio0")); /* Alias to gpio1 */
+		gpio = 9;
+		flags = GPIO_ACTIVE_LOW;
+	} else {
+		snprintf(path, sizeof(path), "%s/gpio at 20",
+			 fdt_get_alias(blob, "i2c1")); /* Alias to i2c2 */
+		gpio = 5;
+		flags = GPIO_ACTIVE_HIGH;
+	}
+
+	node = fdt_path_offset(blob, path);
+	if (node < 0) {
+		pr_err("%s(): unable to locate GPIO node: %s\n", __func__,
+		       path);
+		return 0;
+	}
+
+	handle = fdt_get_phandle(blob, node);
+	if (handle < 0) {
+		pr_err("%s(): unable to locate GPIO controller handle: %s\n",
+		       __func__, path);
+	}
+
+	ret = insert_gpios_prop(blob, phynode, "reset-gpios",
+				handle, gpio, flags);
+	if (ret < 0) {
+		pr_err("%s(): failed to set reset-gpios property\n", __func__);
+		return ret;
+	}
+
+	return 0;
+}
+
+#if defined(CONFIG_OF_BOARD_FIXUP)
+int board_fix_fdt(void *blob)
+{
+	/* Fix U-Boot device tree: */
+	return configure_phy_reset_gpios(blob);
+}
+#endif /* CONFIG_OF_BOARD_FIXUP */
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+	/* Fix kernel device tree: */
+	return configure_phy_reset_gpios(blob);
+}
+#endif /* CONFIG_OF_BOARD_SETUP */
+
 #endif /* CONFIG_SPL_BUILD */
diff --git a/configs/imx8mn_var_som_defconfig b/configs/imx8mn_var_som_defconfig
index f0e232081f..d8a442d623 100644
--- a/configs/imx8mn_var_som_defconfig
+++ b/configs/imx8mn_var_som_defconfig
@@ -22,10 +22,12 @@ CONFIG_SPL_SYS_MALLOC_F_LEN=0x2000
 CONFIG_SPL=y
 CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000
 CONFIG_SYS_LOAD_ADDR=0x40480000
+CONFIG_OF_BOARD_FIXUP=y
 CONFIG_SYS_MONITOR_LEN=524288
 CONFIG_FIT=y
 CONFIG_FIT_EXTERNAL_OFFSET=0x3000
 CONFIG_SPL_LOAD_FIT=y
+CONFIG_OF_BOARD_SETUP=y
 CONFIG_OF_SYSTEM_SETUP=y
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_DEFAULT_FDT_FILE="freescale/imx8mn-var-som-symphony.dtb"
-- 
2.30.2



More information about the U-Boot mailing list