[PATCH 2/2] arm: dts: imx8mp: Sync the DT with kernel 6.4-rc4
Adam Ford
aford173 at gmail.com
Wed May 31 00:45:58 CEST 2023
Several changes have been made to the device tree
in the kernel, so update that as well as the
corresponding imx8mp-u-boot.dtsi files to prevent
breaking the booting.
Signed-off-by: Adam Ford <aford173 at gmail.com>
diff --git a/arch/arm/dts/imx8mp-u-boot.dtsi b/arch/arm/dts/imx8mp-u-boot.dtsi
index 18d1728e1d..dfb747bb02 100644
--- a/arch/arm/dts/imx8mp-u-boot.dtsi
+++ b/arch/arm/dts/imx8mp-u-boot.dtsi
@@ -44,6 +44,9 @@
&aips3 {
bootph-pre-ram;
+ spba-bus at 30800000 {
+ bootph-pre-ram;
+ };
};
&iomuxc {
diff --git a/arch/arm/dts/imx8mp.dtsi b/arch/arm/dts/imx8mp.dtsi
index bb916a0948..428c60462e 100644
--- a/arch/arm/dts/imx8mp.dtsi
+++ b/arch/arm/dts/imx8mp.dtsi
@@ -123,6 +123,7 @@
A53_L2: l2-cache0 {
compatible = "cache";
+ cache-unified;
cache-level = <2>;
cache-size = <0x80000>;
cache-line-size = <64>;
@@ -379,6 +380,8 @@
compatible = "fsl,imx8mp-tmu";
reg = <0x30260000 0x10000>;
clocks = <&clk IMX8MP_CLK_TSENSOR_ROOT>;
+ nvmem-cells = <&tmu_calib>;
+ nvmem-cell-names = "calib";
#thermal-sensor-cells = <1>;
};
@@ -406,12 +409,36 @@
status = "disabled";
};
+ gpt1: timer at 302d0000 {
+ compatible = "fsl,imx8mp-gpt", "fsl,imx6dl-gpt";
+ reg = <0x302d0000 0x10000>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_GPT1_ROOT>, <&clk IMX8MP_CLK_GPT1>;
+ clock-names = "ipg", "per";
+ };
+
+ gpt2: timer at 302e0000 {
+ compatible = "fsl,imx8mp-gpt", "fsl,imx6dl-gpt";
+ reg = <0x302e0000 0x10000>;
+ interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_GPT2_ROOT>, <&clk IMX8MP_CLK_GPT2>;
+ clock-names = "ipg", "per";
+ };
+
+ gpt3: timer at 302f0000 {
+ compatible = "fsl,imx8mp-gpt", "fsl,imx6dl-gpt";
+ reg = <0x302f0000 0x10000>;
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_GPT3_ROOT>, <&clk IMX8MP_CLK_GPT3>;
+ clock-names = "ipg", "per";
+ };
+
iomuxc: pinctrl at 30330000 {
compatible = "fsl,imx8mp-iomuxc";
reg = <0x30330000 0x10000>;
};
- gpr: iomuxc-gpr at 30340000 {
+ gpr: syscon at 30340000 {
compatible = "fsl,imx8mp-iomuxc-gpr", "syscon";
reg = <0x30340000 0x10000>;
};
@@ -424,27 +451,44 @@
#address-cells = <1>;
#size-cells = <1>;
- imx8mp_uid: unique-id at 420 {
+ /*
+ * The register address below maps to the MX8M
+ * Fusemap Description Table entries this way.
+ * Assuming
+ * reg = <ADDR SIZE>;
+ * then
+ * Fuse Address = (ADDR * 4) + 0x400
+ * Note that if SIZE is greater than 4, then
+ * each subsequent fuse is located at offset
+ * +0x10 in Fusemap Description Table (e.g.
+ * reg = <0x8 0x8> describes fuses 0x420 and
+ * 0x430).
+ */
+ imx8mp_uid: unique-id at 8 { /* 0x420-0x430 */
reg = <0x8 0x8>;
};
- cpu_speed_grade: speed-grade at 10 {
+ cpu_speed_grade: speed-grade at 10 { /* 0x440 */
reg = <0x10 4>;
};
- eth_mac1: mac-address at 90 {
+ eth_mac1: mac-address at 90 { /* 0x640 */
reg = <0x90 6>;
};
- eth_mac2: mac-address at 96 {
+ eth_mac2: mac-address at 96 { /* 0x658 */
reg = <0x96 6>;
};
+
+ tmu_calib: calib at 264 { /* 0xd90-0xdc0 */
+ reg = <0x264 0x10>;
+ };
};
- anatop: anatop at 30360000 {
- compatible = "fsl,imx8mp-anatop", "fsl,imx8mm-anatop",
- "syscon";
+ anatop: clock-controller at 30360000 {
+ compatible = "fsl,imx8mp-anatop", "fsl,imx8mm-anatop";
reg = <0x30360000 0x10000>;
+ #clock-cells = <1>;
};
snvs: snvs at 30370000 {
@@ -523,6 +567,7 @@
compatible = "fsl,imx8mp-gpc";
reg = <0x303a0000 0x1000>;
interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
interrupt-controller;
#interrupt-cells = <3>;
@@ -589,7 +634,7 @@
reg = <IMX8MP_POWER_DOMAIN_MIPI_PHY2>;
};
- pgc_hsiomix: power-domains at 17 {
+ pgc_hsiomix: power-domain at 17 {
#power-domain-cells = <0>;
reg = <IMX8MP_POWER_DOMAIN_HSIOMIX>;
clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
@@ -631,6 +676,14 @@
reg = <IMX8MP_POWER_DOMAIN_VPU_VC8000E>;
clocks = <&clk IMX8MP_CLK_VPU_VC8KE_ROOT>;
};
+
+ pgc_mlmix: power-domain at 24 {
+ #power-domain-cells = <0>;
+ reg = <IMX8MP_POWER_DOMAIN_MLMIX>;
+ clocks = <&clk IMX8MP_CLK_ML_AXI>,
+ <&clk IMX8MP_CLK_ML_AHB>,
+ <&clk IMX8MP_CLK_NPU_ROOT>;
+ };
};
};
};
@@ -693,6 +746,30 @@
clocks = <&osc_24m>;
clock-names = "per";
};
+
+ gpt6: timer at 306e0000 {
+ compatible = "fsl,imx8mp-gpt", "fsl,imx6dl-gpt";
+ reg = <0x306e0000 0x10000>;
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_GPT6_ROOT>, <&clk IMX8MP_CLK_GPT6>;
+ clock-names = "ipg", "per";
+ };
+
+ gpt5: timer at 306f0000 {
+ compatible = "fsl,imx8mp-gpt", "fsl,imx6dl-gpt";
+ reg = <0x306f0000 0x10000>;
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_GPT5_ROOT>, <&clk IMX8MP_CLK_GPT5>;
+ clock-names = "ipg", "per";
+ };
+
+ gpt4: timer at 30700000 {
+ compatible = "fsl,imx8mp-gpt", "fsl,imx6dl-gpt";
+ reg = <0x30700000 0x10000>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_GPT4_ROOT>, <&clk IMX8MP_CLK_GPT4>;
+ clock-names = "ipg", "per";
+ };
};
aips3: bus at 30800000 {
@@ -702,112 +779,129 @@
#size-cells = <1>;
ranges;
- ecspi1: spi at 30820000 {
+ spba-bus at 30800000 {
+ compatible = "fsl,spba-bus", "simple-bus";
+ reg = <0x30800000 0x100000>;
#address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx8mp-ecspi", "fsl,imx51-ecspi";
- reg = <0x30820000 0x10000>;
- interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clk IMX8MP_CLK_ECSPI1_ROOT>,
- <&clk IMX8MP_CLK_ECSPI1_ROOT>;
- clock-names = "ipg", "per";
- dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
+ #size-cells = <1>;
+ ranges;
- ecspi2: spi at 30830000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx8mp-ecspi", "fsl,imx51-ecspi";
- reg = <0x30830000 0x10000>;
- interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clk IMX8MP_CLK_ECSPI2_ROOT>,
- <&clk IMX8MP_CLK_ECSPI2_ROOT>;
- clock-names = "ipg", "per";
- dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
+ ecspi1: spi at 30820000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi";
+ reg = <0x30820000 0x10000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_ECSPI1_ROOT>,
+ <&clk IMX8MP_CLK_ECSPI1_ROOT>;
+ clock-names = "ipg", "per";
+ assigned-clock-rates = <80000000>;
+ assigned-clocks = <&clk IMX8MP_CLK_ECSPI1>;
+ assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>;
+ dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
- ecspi3: spi at 30840000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx8mp-ecspi", "fsl,imx51-ecspi";
- reg = <0x30840000 0x10000>;
- interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clk IMX8MP_CLK_ECSPI3_ROOT>,
- <&clk IMX8MP_CLK_ECSPI3_ROOT>;
- clock-names = "ipg", "per";
- dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
+ ecspi2: spi at 30830000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi";
+ reg = <0x30830000 0x10000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_ECSPI2_ROOT>,
+ <&clk IMX8MP_CLK_ECSPI2_ROOT>;
+ clock-names = "ipg", "per";
+ assigned-clock-rates = <80000000>;
+ assigned-clocks = <&clk IMX8MP_CLK_ECSPI2>;
+ assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>;
+ dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
- uart1: serial at 30860000 {
- compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart";
- reg = <0x30860000 0x10000>;
- interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clk IMX8MP_CLK_UART1_ROOT>,
- <&clk IMX8MP_CLK_UART1_ROOT>;
- clock-names = "ipg", "per";
- dmas = <&sdma1 22 4 0>, <&sdma1 23 4 0>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
+ ecspi3: spi at 30840000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi";
+ reg = <0x30840000 0x10000>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_ECSPI3_ROOT>,
+ <&clk IMX8MP_CLK_ECSPI3_ROOT>;
+ clock-names = "ipg", "per";
+ assigned-clock-rates = <80000000>;
+ assigned-clocks = <&clk IMX8MP_CLK_ECSPI3>;
+ assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>;
+ dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
- uart3: serial at 30880000 {
- compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart";
- reg = <0x30880000 0x10000>;
- interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clk IMX8MP_CLK_UART3_ROOT>,
- <&clk IMX8MP_CLK_UART3_ROOT>;
- clock-names = "ipg", "per";
- dmas = <&sdma1 26 4 0>, <&sdma1 27 4 0>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
+ uart1: serial at 30860000 {
+ compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart";
+ reg = <0x30860000 0x10000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_UART1_ROOT>,
+ <&clk IMX8MP_CLK_UART1_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 22 4 0>, <&sdma1 23 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
- uart2: serial at 30890000 {
- compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart";
- reg = <0x30890000 0x10000>;
- interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clk IMX8MP_CLK_UART2_ROOT>,
- <&clk IMX8MP_CLK_UART2_ROOT>;
- clock-names = "ipg", "per";
- dmas = <&sdma1 24 4 0>, <&sdma1 25 4 0>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
+ uart3: serial at 30880000 {
+ compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart";
+ reg = <0x30880000 0x10000>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_UART3_ROOT>,
+ <&clk IMX8MP_CLK_UART3_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 26 4 0>, <&sdma1 27 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
- flexcan1: can at 308c0000 {
- compatible = "fsl,imx8mp-flexcan";
- reg = <0x308c0000 0x10000>;
- interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clk IMX8MP_CLK_IPG_ROOT>,
- <&clk IMX8MP_CLK_CAN1_ROOT>;
- clock-names = "ipg", "per";
- assigned-clocks = <&clk IMX8MP_CLK_CAN1>;
- assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_40M>;
- assigned-clock-rates = <40000000>;
- fsl,clk-source = /bits/ 8 <0>;
- fsl,stop-mode = <&gpr 0x10 4>;
- status = "disabled";
- };
+ uart2: serial at 30890000 {
+ compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart";
+ reg = <0x30890000 0x10000>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_UART2_ROOT>,
+ <&clk IMX8MP_CLK_UART2_ROOT>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma1 24 4 0>, <&sdma1 25 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
- flexcan2: can at 308d0000 {
- compatible = "fsl,imx8mp-flexcan";
- reg = <0x308d0000 0x10000>;
- interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clk IMX8MP_CLK_IPG_ROOT>,
- <&clk IMX8MP_CLK_CAN2_ROOT>;
- clock-names = "ipg", "per";
- assigned-clocks = <&clk IMX8MP_CLK_CAN2>;
- assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_40M>;
- assigned-clock-rates = <40000000>;
- fsl,clk-source = /bits/ 8 <0>;
- fsl,stop-mode = <&gpr 0x10 5>;
- status = "disabled";
+ flexcan1: can at 308c0000 {
+ compatible = "fsl,imx8mp-flexcan";
+ reg = <0x308c0000 0x10000>;
+ interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_IPG_ROOT>,
+ <&clk IMX8MP_CLK_CAN1_ROOT>;
+ clock-names = "ipg", "per";
+ assigned-clocks = <&clk IMX8MP_CLK_CAN1>;
+ assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_40M>;
+ assigned-clock-rates = <40000000>;
+ fsl,clk-source = /bits/ 8 <0>;
+ fsl,stop-mode = <&gpr 0x10 4>;
+ status = "disabled";
+ };
+
+ flexcan2: can at 308d0000 {
+ compatible = "fsl,imx8mp-flexcan";
+ reg = <0x308d0000 0x10000>;
+ interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_IPG_ROOT>,
+ <&clk IMX8MP_CLK_CAN2_ROOT>;
+ clock-names = "ipg", "per";
+ assigned-clocks = <&clk IMX8MP_CLK_CAN2>;
+ assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_40M>;
+ assigned-clock-rates = <40000000>;
+ fsl,clk-source = /bits/ 8 <0>;
+ fsl,stop-mode = <&gpr 0x10 5>;
+ status = "disabled";
+ };
};
crypto: crypto at 30900000 {
@@ -1063,11 +1157,11 @@
noc_opp_table: opp-table {
compatible = "operating-points-v2";
- opp-200M {
+ opp-200000000 {
opp-hz = /bits/ 64 <200000000>;
};
- opp-1000M {
+ opp-1000000000 {
opp-hz = /bits/ 64 <1000000000>;
};
};
@@ -1080,10 +1174,78 @@
#size-cells = <1>;
ranges;
+ mipi_dsi: dsi at 32e60000 {
+ compatible = "fsl,imx8mp-mipi-dsim";
+ reg = <0x32e60000 0x400>;
+ clocks = <&clk IMX8MP_CLK_MEDIA_APB_ROOT>,
+ <&clk IMX8MP_CLK_MEDIA_MIPI_PHY1_REF>;
+ clock-names = "bus_clk", "sclk_mipi";
+ assigned-clocks = <&clk IMX8MP_CLK_MEDIA_APB>,
+ <&clk IMX8MP_CLK_MEDIA_MIPI_PHY1_REF>;
+ assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>,
+ <&clk IMX8MP_CLK_24M>;
+ assigned-clock-rates = <200000000>, <24000000>;
+ samsung,pll-clock-frequency = <24000000>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&media_blk_ctrl IMX8MP_MEDIABLK_PD_MIPI_DSI_1>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+
+ dsim_from_lcdif1: endpoint {
+ remote-endpoint = <&lcdif1_to_dsim>;
+ };
+ };
+ };
+ };
+
+ lcdif1: display-controller at 32e80000 {
+ compatible = "fsl,imx8mp-lcdif";
+ reg = <0x32e80000 0x10000>;
+ clocks = <&clk IMX8MP_CLK_MEDIA_DISP1_PIX_ROOT>,
+ <&clk IMX8MP_CLK_MEDIA_APB_ROOT>,
+ <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>;
+ clock-names = "pix", "axi", "disp_axi";
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&media_blk_ctrl IMX8MP_MEDIABLK_PD_LCDIF_1>;
+ status = "disabled";
+
+ port {
+ lcdif1_to_dsim: endpoint {
+ remote-endpoint = <&dsim_from_lcdif1>;
+ };
+ };
+ };
+
+ lcdif2: display-controller at 32e90000 {
+ compatible = "fsl,imx8mp-lcdif";
+ reg = <0x32e90000 0x10000>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_MEDIA_DISP2_PIX_ROOT>,
+ <&clk IMX8MP_CLK_MEDIA_APB_ROOT>,
+ <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>;
+ clock-names = "pix", "axi", "disp_axi";
+ power-domains = <&media_blk_ctrl IMX8MP_MEDIABLK_PD_LCDIF_2>;
+ status = "disabled";
+
+ port {
+ lcdif2_to_ldb: endpoint {
+ remote-endpoint = <&ldb_from_lcdif2>;
+ };
+ };
+ };
+
media_blk_ctrl: blk-ctrl at 32ec0000 {
compatible = "fsl,imx8mp-media-blk-ctrl",
"syscon";
reg = <0x32ec0000 0x10000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
power-domains = <&pgc_mediamix>,
<&pgc_mipi_phy1>,
<&pgc_mipi_phy1>,
@@ -1122,12 +1284,55 @@
"disp1", "disp2", "isp", "phy";
assigned-clocks = <&clk IMX8MP_CLK_MEDIA_AXI>,
- <&clk IMX8MP_CLK_MEDIA_APB>;
+ <&clk IMX8MP_CLK_MEDIA_APB>,
+ <&clk IMX8MP_CLK_MEDIA_DISP1_PIX>,
+ <&clk IMX8MP_CLK_MEDIA_DISP2_PIX>,
+ <&clk IMX8MP_VIDEO_PLL1>;
assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_1000M>,
- <&clk IMX8MP_SYS_PLL1_800M>;
- assigned-clock-rates = <500000000>, <200000000>;
-
+ <&clk IMX8MP_SYS_PLL1_800M>,
+ <&clk IMX8MP_VIDEO_PLL1_OUT>,
+ <&clk IMX8MP_VIDEO_PLL1_OUT>;
+ assigned-clock-rates = <500000000>, <200000000>,
+ <0>, <0>, <1039500000>;
#power-domain-cells = <1>;
+
+ lvds_bridge: bridge at 5c {
+ compatible = "fsl,imx8mp-ldb";
+ reg = <0x5c 0x4>, <0x128 0x4>;
+ reg-names = "ldb", "lvds";
+ clocks = <&clk IMX8MP_CLK_MEDIA_LDB>;
+ clock-names = "ldb";
+ assigned-clocks = <&clk IMX8MP_CLK_MEDIA_LDB>;
+ assigned-clock-parents = <&clk IMX8MP_VIDEO_PLL1_OUT>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+
+ ldb_from_lcdif2: endpoint {
+ remote-endpoint = <&lcdif2_to_ldb>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+
+ ldb_lvds_ch0: endpoint {
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
+
+ ldb_lvds_ch1: endpoint {
+ };
+ };
+ };
+ };
};
pcie_phy: pcie-phy at 32f00000 {
@@ -1158,6 +1363,7 @@
<&noc IMX8MP_ICM_PCIE &noc IMX8MP_ICN_HSIO>;
interconnect-names = "noc-pcie", "usb1", "usb2", "pcie";
#power-domain-cells = <1>;
+ #clock-cells = <0>;
};
};
@@ -1165,6 +1371,13 @@
compatible = "fsl,imx8mp-pcie";
reg = <0x33800000 0x400000>, <0x1ff00000 0x80000>;
reg-names = "dbi", "config";
+ clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
+ <&clk IMX8MP_CLK_HSIO_AXI>,
+ <&clk IMX8MP_CLK_PCIE_ROOT>;
+ clock-names = "pcie", "pcie_bus", "pcie_aux";
+ assigned-clocks = <&clk IMX8MP_CLK_PCIE_AUX>;
+ assigned-clock-rates = <10000000>;
+ assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_50M>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
@@ -1192,6 +1405,32 @@
status = "disabled";
};
+ pcie_ep: pcie-ep at 33800000 {
+ compatible = "fsl,imx8mp-pcie-ep";
+ reg = <0x33800000 0x000400000>, <0x18000000 0x08000000>;
+ reg-names = "dbi", "addr_space";
+ clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
+ <&clk IMX8MP_CLK_HSIO_AXI>,
+ <&clk IMX8MP_CLK_PCIE_ROOT>;
+ clock-names = "pcie", "pcie_bus", "pcie_aux";
+ assigned-clocks = <&clk IMX8MP_CLK_PCIE_AUX>;
+ assigned-clock-rates = <10000000>;
+ assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_50M>;
+ num-lanes = <1>;
+ interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; /* eDMA */
+ interrupt-names = "dma";
+ fsl,max-link-speed = <3>;
+ power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_PCIE>;
+ resets = <&src IMX8MP_RESET_PCIE_CTRL_APPS_EN>,
+ <&src IMX8MP_RESET_PCIE_CTRL_APPS_TURNOFF>;
+ reset-names = "apps", "turnoff";
+ phys = <&pcie_phy>;
+ phy-names = "pcie-phy";
+ num-ib-windows = <4>;
+ num-ob-windows = <4>;
+ status = "disabled";
+ };
+
gpu3d: gpu at 38000000 {
compatible = "vivante,gc";
reg = <0x38000000 0x8000>;
@@ -1223,6 +1462,28 @@
power-domains = <&pgc_gpu2d>;
};
+ vpu_g1: video-codec at 38300000 {
+ compatible = "nxp,imx8mm-vpu-g1";
+ reg = <0x38300000 0x10000>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_VPU_G1_ROOT>;
+ assigned-clocks = <&clk IMX8MP_CLK_VPU_G1>;
+ assigned-clock-parents = <&clk IMX8MP_VPU_PLL_OUT>;
+ assigned-clock-rates = <600000000>;
+ power-domains = <&vpumix_blk_ctrl IMX8MP_VPUBLK_PD_G1>;
+ };
+
+ vpu_g2: video-codec at 38310000 {
+ compatible = "nxp,imx8mq-vpu-g2";
+ reg = <0x38310000 0x10000>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clk IMX8MP_CLK_VPU_G2_ROOT>;
+ assigned-clocks = <&clk IMX8MP_CLK_VPU_G2>;
+ assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_1000M>;
+ assigned-clock-rates = <500000000>;
+ power-domains = <&vpumix_blk_ctrl IMX8MP_VPUBLK_PD_G2>;
+ };
+
vpumix_blk_ctrl: blk-ctrl at 38330000 {
compatible = "fsl,imx8mp-vpu-blk-ctrl", "syscon";
reg = <0x38330000 0x100>;
@@ -1234,6 +1495,9 @@
<&clk IMX8MP_CLK_VPU_G2_ROOT>,
<&clk IMX8MP_CLK_VPU_VC8KE_ROOT>;
clock-names = "g1", "g2", "vc8000e";
+ assigned-clocks = <&clk IMX8MP_CLK_VPU_BUS>, <&clk IMX8MP_VPU_PLL>;
+ assigned-clock-parents = <&clk IMX8MP_VPU_PLL_OUT>;
+ assigned-clock-rates = <600000000>, <600000000>;
interconnects = <&noc IMX8MP_ICM_VPU_G1 &noc IMX8MP_ICN_VIDEO>,
<&noc IMX8MP_ICM_VPU_G2 &noc IMX8MP_ICN_VIDEO>,
<&noc IMX8MP_ICM_VPU_H1 &noc IMX8MP_ICN_VIDEO>;
@@ -1279,7 +1543,7 @@
reg = <0x32f10100 0x8>,
<0x381f0000 0x20>;
clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
- <&clk IMX8MP_CLK_USB_ROOT>;
+ <&clk IMX8MP_CLK_USB_SUSP>;
clock-names = "hsio", "suspend";
interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB>;
@@ -1292,9 +1556,9 @@
usb_dwc3_0: usb at 38100000 {
compatible = "snps,dwc3";
reg = <0x38100000 0x10000>;
- clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
+ clocks = <&clk IMX8MP_CLK_USB_ROOT>,
<&clk IMX8MP_CLK_USB_CORE_REF>,
- <&clk IMX8MP_CLK_USB_ROOT>;
+ <&clk IMX8MP_CLK_USB_SUSP>;
clock-names = "bus_early", "ref", "suspend";
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
phys = <&usb3_phy0>, <&usb3_phy0>;
@@ -1321,7 +1585,7 @@
reg = <0x32f10108 0x8>,
<0x382f0000 0x20>;
clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
- <&clk IMX8MP_CLK_USB_ROOT>;
+ <&clk IMX8MP_CLK_USB_SUSP>;
clock-names = "hsio", "suspend";
interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB>;
@@ -1334,9 +1598,9 @@
usb_dwc3_1: usb at 38200000 {
compatible = "snps,dwc3";
reg = <0x38200000 0x10000>;
- clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
+ clocks = <&clk IMX8MP_CLK_USB_ROOT>,
<&clk IMX8MP_CLK_USB_CORE_REF>,
- <&clk IMX8MP_CLK_USB_ROOT>;
+ <&clk IMX8MP_CLK_USB_SUSP>;
clock-names = "bus_early", "ref", "suspend";
interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
phys = <&usb3_phy1>, <&usb3_phy1>;
--
2.39.2
More information about the U-Boot
mailing list